One of the other groups here, has just put in a new Foxboro node, and I was
seting up save_all.sh to autobackup the control config's for them.
However, much to my suprise it failed to bacxkup the AB integrator, and
FoxWatch modules on that node.
Her's the log:
Save-all for all stations in
We have two FT pair of CP60s installed in our operating units and in both
cases the Fieldbus has caused us numerous headaches until we figured out
the correct installation. In fact we are still having some problems. We
thought the coax ethernet cabling would be easy, but we discovered
We have been using eXceeds for years now without to many problems. The only
issues we have had, occurred with some changes Hummingbird has implemented
in various software revs. Exceed has been installed on a number of PCs that
have Windows2000 with out any problems and we still use the original
Hi Stan,
Wat type of module is the FoxWatch module? I would not expect a comms processor to be
in /etc/cplns on the system. (FOXWATCH is
usually a COMM10 and does not contain a control database)
Was the system configuration passed through all stations? (just to sync the system
files like
I am surprised that Foxboro support did not tell you to do
a dft replace_sys ESPx SCSI3
this is a front end command to the metareplace command that is
mentioned in the output.
wb
From: Weiss, Andreas [EMAIL PROTECTED]
Reply-To: Foxboro DCS Mail List [EMAIL PROTECTED]
To: 'Foxboro DCS Mail
There's always an excuse
Ron
Johnson, Alex (Foxboro) wrote:
I forgot about AWs. Sigh...
I'm in the UK, think I can blame jet lag?
Regards,
Alex Johnson
10707 Haddington
Houston, TX 77043
713.722.2859 (office)
713.722.2700 (switchboard)
713.932.0222 (fax)
[EMAIL PROTECTED]
Yes they were all updated. This doesn't seem to be the problem, but we'll
keep checking.
Thanks for your assistance.
John
I know all FBM's require EEPROM update for version 6.2.1. But you have
I have a question about /etc/wplns and /etc/aplns
I have some scripts which check various things about a givrn Foxboro node,
and mail the results to the people concerned. These scripts use /etc/wplns,
and /etc/aplns respectivly to determine what wp's, and ap's should exist on
a systesm (aw's
Stefano Persico wrote:
Hi list
is it possible to estract data from AIM*Historian samples and convert
them in some easy format ( ASCII ) ???
In other words is it possible to read into an ms office application
samples from AIM*AT ??
Thanks
Have a look at gethist on the Cassandra site. It
Eudilson,
You can try to use remv/remd tools
Gook Luck
Chiaju
-Original Message-
From: Eudilson Nunez Cossio [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, May 02, 2001 9:56 PM
To: Foxboro DCS Mail List
Subject: Monitoring system variables
Hi,
I would like to monitoring some variables
I noticed you have CP60FT. The filedbus cabling can be confusing and you may
have both fieldbusses connected to eachother. Take care of termination and as
mentioned here: do not branch. Termination will not be correct. Only two must be
installed per fieldbus.
Ron
Campbell John C wrote:
Yes
Hi list
is it possible to estract data from AIM*Historian samples and convert
them in some easy format ( ASCII ) ???
In other words is it possible to read into an ms office application
samples from AIM*AT ??
Thanks
---
This
Hi All,
We have two AWs with mirrored concatenated drives.
I got curious yesterday and ran dft show_status was amazed and
embarrassed to find one of the AWs had been un-mirrored for quite some time.
I read HH745 and HH835, the entire section on mirrored drives in the
Foxboro System
We use single CP60's and got the same problem (we are using 200 series I/O) the
problem went away when we went to 24 FBM's. When we had 23 FBM's the fault was as you
explained regardless of FBM location. The errors predominantly reported to an
individual location and usually to a FBM204
14 matches
Mail list logo
