Re: [Frameworks] Problem with projector's lamp
Hi Esperanza, This happened to me once but I the take up reel was also not working and I realized that I had it selected as STILL rather than RUN on top. I'm not sure what else it could be other than that? Hope it helps! Regards, Pedro > On Jan 9, 2016, at 1:08 PM, Esperanza Collado> wrote: > > Dear Frameworkers, > > Im about to present a projector's performance and one of the projector's > lamps stopped working. I checked fuses, which are fine and i replaced the > lamp three times but the light wont appear. Optical lamp works as well as > everything else. Any idea what could it be? It is an Eiki SL-2. > > Hopefully someone can help! > Thank you, > Esperanza > > > -- > Esperanza Collado > - - - - - - - - - - - - - - > www.esperanzacollado.org > > ___ > FrameWorks mailing list > FrameWorks@jonasmekasfilms.com > https://mailman-mail5.webfaction.com/listinfo/frameworks ___ FrameWorks mailing list FrameWorks@jonasmekasfilms.com https://mailman-mail5.webfaction.com/listinfo/frameworks
Re: [Frameworks] Problem with projector's lamp
The first thing I would do is check for direct current voltage at the lamp terminals with a multi-tester.According to an online manual the proper lamp is a 250 watt 24-volt ELC. A 200-watt 24-volt ELJ may alternately be used with less output. With the lamp switch ON you should be getting about 22 VDC in the low position and 24 VDC in the high position.If the current is present, the problem is with the lamps. If no current there is a bad connection or a problem with the power transformer. Ed-Original Message- From: Esperanza ColladoSent: Jan 9, 2016 12:08 PM To: Experimental Film Discussion List Subject: [Frameworks] Problem with projector's lamp Dear Frameworkers, Im about to present a projector's performance and one of the projector's lamps stopped working. I checked fuses, which are fine and i replaced the lamp three times but the light wont appear. Optical lamp works as well as everything else. Any idea what could it be? It is an Eiki SL-2. Hopefully someone can help! Thank you,Esperanza-- Esperanza Collado- - - - - - - - - - - - - - www.esperanzacollado.org ___ FrameWorks mailing list FrameWorks@jonasmekasfilms.com https://mailman-mail5.webfaction.com/listinfo/frameworks
Re: [Frameworks] Problem with projector's lamp
It worked in the end. I cleaned the white piece where the pins of the lamp sit several times and then tested if lamp worked several times. It wouldnt work for a white but in the end it did! What a fright... I really appreciate your prompt responses. Thank you!!! Esperanza El sábado, 9 de enero de 2016, Ed Inmanescribió: > The first thing I would do is check for direct current voltage at the lamp > terminals with a multi-tester. > According to an online manual the proper lamp is a 250 watt 24-volt ELC. A > 200-watt 24-volt ELJ may alternately be used with less output. > With the lamp switch ON you should be getting about 22 VDC in the low > position and 24 VDC in the high position. > If the current is present, the problem is with the lamps. If no current > there is a bad connection or a problem with the power transformer. > Ed > > > -Original Message- > From: Esperanza Collado > Sent: Jan 9, 2016 12:08 PM > To: Experimental Film Discussion List > Subject: [Frameworks] Problem with projector's lamp > > Dear Frameworkers, > > Im about to present a projector's performance and one of the projector's > lamps stopped working. I checked fuses, which are fine and i replaced the > lamp three times but the light wont appear. Optical lamp works as well > as everything else. Any idea what could it be? It is an Eiki SL-2. > > Hopefully someone can help! > Thank you, > Esperanza > > > -- > Esperanza Collado > - - - - - - - - - - - - - - > www.esperanzacollado.org > > -- Esperanza Collado - - - - - - - - - - - - - - www.esperanzacollado.org ___ FrameWorks mailing list FrameWorks@jonasmekasfilms.com https://mailman-mail5.webfaction.com/listinfo/frameworks