Re: Kernel built with new GCC panics immediately
--- Lukas Ertl [EMAIL PROTECTED] wrote: Hi there, just wanted to report that a kernel built with the new gcc panics immediately when booting. I've seen this on two machines. Panic and reboot happens fast that I couldn't get the panic message. Same here for an AMD Athlon a Pentium III. The panic message for AMD is: Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-CURRENT #20030712: Sat Jul 12 01:35:44 HKT 2003 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/SHIZUKA Preloaded elf kernel /boot/kernel/kernel at 0xc058a000. Preloaded elf module /boot/kernel/acpi.ko at 0xc058a1f4. Timecounter i8254 frequency 1193182 Hz CPU: AMD Unknown (286-class CPU) Origin = AuthenticAMD Stepping = 0 panic: CPU class not configured Debugger(panic) Stopped at Debugger+0x54: xchgl %ebx,in_Debugger.0 db trace Debugger(c03f6b71,c047,c0408af7,c05acd4c,100) at Debugger+0x54 panic(c0408af7,c05acd80,c03aaff7,c0262967,c0577880) at panic+0xd5 panicifcpuunsupported(c0262967,c0577880,0,c040705f,c05acd68) at panicifcpuunsup orted+0x1b cpu_startup(0,5a9000,5a9c00,5a9000,0) at cpu_startup+0x17 mi_startup() at mi_startup+0xb5 begin() at begin+0x2c regards, le -- Lukas Ertl eMail: [EMAIL PROTECTED] UNIX-Systemadministrator Tel.: (+43 1) 4277-14073 Zentraler Informatikdienst (ZID) Fax.: (+43 1) 4277-9140 der Universität Wien http://mailbox.univie.ac.at/~le/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED] __ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! http://sbc.yahoo.com ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]
gcc 3.3.1
Don't forget bump __FreeBSD_version. :) Sem. ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]
setting CPUTYPE=p4 with gcc-3.3
Is it safe to set CPUTYPE to p4 for those with p4 processors now that gcc has been upgraded to 3.3 in -CURRENT? If so, should this be set up accordingly in bsd.cpu.mk? -- Glenn Johnson [EMAIL PROTECTED] ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: [acpi-jp 2393] Re: Updated ec-burst.diff patch
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 Attached is some hokey magic, which will cause your system to panic if you have a device plugged in a being access when you go into suspend. The panic will be on resume. I think it is because the usb interrupts change at least that is what i gather from gdb. It is only for ohci since that's all I have, but I'm sure the same stuff will work for uhci and ehci. If there is a way to force all the usb device to detach right before we suspend then there is a good chance that this could work without causing panics. - -- Anish Mistry -BEGIN PGP SIGNATURE- Version: GnuPG v1.2.2 (FreeBSD) iD8DBQE/D4enxqA5ziudZT0RAjvTAKDSxYlsr4Psrb2qHPWMKoiSeucAMACdHqac wrk2eRCKrC3EJiQlRVrZhRk= =JEYV -END PGP SIGNATURE- ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: nvidia-driver database?
On 2003-07-11 20:48 +, Evan Dower wrote: We've been posting our success stories and problems for a few days now. Has anybody tried to compile these sorts of things into some sort of database? Maybe something keeping track of hardware, configuration details, and performance (success or symptoms)? If not, is anyone interested in creating one? I would but am not well equipped (in other words I don't know how). Is there interest in something like this? Are there willing victi... I mean... volunteers? E I'm maintaining the FAQ at http://www.soulwax.net/nvidia/faq.shtml (warning: not MSIE friendly). I'm slightly short on time for now, but if someone is willing to help me out I have no problem extending it to include something like what you're describing. -- Munish Chopra ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]
Regarding VMWare 3.0 Port and an odd bug that i've been gettingover and over again...
I've been using VMWare in 5.1-RELEASE for quite some time and such, and have ALWAYS gotten this bug and haven't been able to figure out exactly why it does this, but it requires me to reboot. Anyhow here's the layout of the system. P3 800Mhz with 512meg of SDRAM AHA 2940U2W, Dual 17Gig Ultra Scsi 2's (LVD) no IDE devices, IDE is normally disabled, Matrox G400 Dual head without HAL. Soundblaster PCI 512, (emu10k1) using waimea as the window manager (or kde doesn't seem to make this bug better) using netgraph bridging, i have the RTC.ko loaded (that's another nuisance i'd love to correct maybe when I have more time) I've tried reinstalling VMWare and even on a fresh FreeBSD install it gives this error. Attached are some files for you to see Scott M. Likens -- I think we ought to be out there doing what we do best - making large holes in other people's countries. - George Carlin Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-RELEASE #0: Thu Jul 10 18:28:48 PDT 2003 [EMAIL PROTECTED]:/usr/src/sys/i386/compile/LIVID Preloaded elf kernel /boot/kernel/kernel at 0xc04fd000. Preloaded elf module /boot/kernel/vesa.ko at 0xc04fd1f4. Preloaded elf module /boot/kernel/linux.ko at 0xc04fd2a0. Preloaded elf module /boot/kernel/snd_emu10k1.ko at 0xc04fd34c. Preloaded elf module /boot/kernel/snd_pcm.ko at 0xc04fd3fc. Preloaded elf module /boot/kernel/mga.ko at 0xc04fd4a8. Preloaded elf module /boot/kernel/acpi.ko at 0xc04fd550. Timecounter i8254 frequency 1193182 Hz Timecounter TSC frequency 797968113 Hz CPU: Intel Pentium III (797.97-MHz 686-class CPU) Origin = GenuineIntel Id = 0x683 Stepping = 3 Features=0x383f9ffFPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE real memory = 536854528 (511 MB) avail memory = 515981312 (492 MB) Pentium Pro MTRR support enabled VESA: v3.0, 16384k memory, flags:0x1, mode table:0xc00c52bd (c00052bd) VESA: Matrox Graphics Inc. npx0: math processor on motherboard npx0: INT 16 interface acpi0: ASUS CUV4Xon motherboard pcibios: BIOS version 2.10 Using $PIR table, 8 entries at 0xc00f0e60 ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT acpi0: power button is handled as a fixed feature programming model. Timecounter ACPI-fast frequency 3579545 Hz ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT acpi_timer0: 24-bit timer at 3.579545MHz port 0xe408-0xe40b on acpi0 acpi_cpu0: CPU on acpi0 acpi_button0: Power Button on acpi0 pcib0: ACPI Host-PCI bridge port 0xcf8-0xcff on acpi0 pci0: ACPI PCI bus on pcib0 agp0: VIA Generic host to PCI bridge mem 0xe400-0xe7ff at device 0.0 on pci0 pcib1: PCI-PCI bridge at device 1.0 on pci0 pci1: PCI bus on pcib1 drm0: Matrox G400/G450 (AGP) mem 0xe080-0xe0ff,0xe100-0xe1003fff,0xe200-0xe3ff irq 11 at device 0.0 on pci1 info: [drm] AGP at 0xe400 64MB info: [drm] Initialized mga 3.1.0 20021029 on minor 0 isab0: PCI-ISA bridge at device 4.0 on pci0 isa0: ISA bus on isab0 atapci0: VIA 82C686A UDMA66 controller port 0xd800-0xd80f at device 4.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 ahc0: Adaptec 2940 Ultra2 SCSI adapter port 0xb800-0xb8ff mem 0xe000-0xefff irq 10 at device 14.0 on pci0 aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs pcm0: Creative EMU10K1 port 0xb400-0xb41f irq 7 at device 16.0 on pci0 pcm0: TriTech TR28602 AC97 Codec xl0: 3Com 3c905C-TX Fast Etherlink XL port 0xa800-0xa87f mem 0xdf80-0xdf80007f irq 11 at device 17.0 on pci0 xl0: Ethernet address: 00:50:da:1c:29:c8 miibus0: MII bus on xl0 xlphy0: 3c905C 10/100 internal PHY on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fdc0: Enhanced floppy controller (i82077, NE72065 or clone) port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: 1440-KB 3.5 drive on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A atkbdc0: Keyboard controller (i8042) port 0x64,0x60 irq 1 on acpi0 atkbd0: AT Keyboard flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.PX40.PS2M._STA] (Node 0xc4010800), AE_AML_REGION_LIMIT ACPI-0175: ***
[-CURRENT tinderbox] failure on alpha/alpha
TB --- 2003-07-12 04:00:01 - starting CURRENT tinderbox run for alpha/alpha TB --- 2003-07-12 04:00:01 - checking out the source tree TB --- cd /home/des/tinderbox/CURRENT/alpha/alpha TB --- /usr/bin/cvs -f -R -q -d/home/ncvs update -Pd -A src TB --- 2003-07-12 04:04:21 - building world TB --- cd /home/des/tinderbox/CURRENT/alpha/alpha/src TB --- /usr/bin/make -B buildworld Building an up-to-date make(1) Rebuilding the temporary build tree stage 1: legacy release compatibility shims stage 1: bootstrap tools stage 2: cleaning up the object tree stage 2: rebuilding the object tree stage 2: build tools stage 3: cross tools stage 4: populating /home/des/tinderbox/CURRENT/alpha/alpha/obj/alpha/vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src/i386/usr/include stage 4: building libraries stage 4: make dependencies stage 4: building everything.. [...] p: not found ./gengenrtl: ÿGþ/ø¤àÃÿGþ/ð¤àÃÿGþ/è¤: not found ./gengenrtl: þ/è¤: not found ./gengenrtl: àÃÿGþ/à¤àÃÿGþ/0}§^z[kÿGþ/^§Þ#úkþ/»½#àÿÞ#^·µ^µ ðG #^·µ^µ ðG ðG ÿG*?Ð }§1X[kº½#ôéGV?Ð }§*X[kº'@½#ôéGS?Ð }§#X[kº$½#ôéGn?Ð }§X[kº½#äþ/_!êC^§: not found ./gengenrtl: 32: Syntax error: ) unexpected *** Error code 2 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src/gnu/usr.bin/cc/cc_tools. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src/gnu/usr.bin/cc. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src/gnu/usr.bin. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src/gnu. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/alpha/alpha/src. TB --- 2003-07-12 04:49:24 - /usr/bin/make returned exit code 1 TB --- 2003-07-12 04:49:24 - ERROR: failed to build world TB --- 2003-07-12 04:49:24 - tinderbox aborted ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: setting CPUTYPE=p4 with gcc-3.3
On Fri, Jul 11, 2003 at 09:10:14PM -0500, Glenn Johnson wrote: Is it safe to set CPUTYPE to p4 for those with p4 processors now that gcc has been upgraded to 3.3 in -CURRENT? Compile some of the code that was known to be bad (see the archives for extensive discussion) and tell us :) Kris pgp0.pgp Description: PGP signature
[-CURRENT tinderbox] failure on amd64/amd64
TB --- 2003-07-12 04:49:24 - starting CURRENT tinderbox run for amd64/amd64 TB --- 2003-07-12 04:49:24 - checking out the source tree TB --- cd /home/des/tinderbox/CURRENT/amd64/amd64 TB --- /usr/bin/cvs -f -R -q -d/home/ncvs update -Pd -A src TB --- 2003-07-12 04:51:54 - building world TB --- cd /home/des/tinderbox/CURRENT/amd64/amd64/src TB --- /usr/bin/make -B buildworld Building an up-to-date make(1) Rebuilding the temporary build tree stage 1: legacy release compatibility shims stage 1: bootstrap tools stage 2: cleaning up the object tree stage 2: rebuilding the object tree stage 2: build tools stage 3: cross tools stage 4: populating /home/des/tinderbox/CURRENT/amd64/amd64/obj/amd64/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/i386/usr/include stage 4: building libraries stage 4: make dependencies stage 4: building everything.. [...] makeinfo --no-validate -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/binutils/gas/doc -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/binutils/ld -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/binutils/bfd/doc -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/binutils/binutils -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/gdb/gdb/doc -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/gdb/gdb/mi -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/libreadline/doc --no-split -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc -I /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src! /gnu/usr.bin/binutils/doc/../../../../contrib/binutils /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/binutils/doc/../../../../contrib/binutils/binutils/doc/binutils.texi -o binutils.info gzip -cn binutils.info binutils.info.gz === gnu/usr.bin/cc === gnu/usr.bin/cc/cc_tools cc -O -pipe -I. -static -DGENERATOR_FILE -DIN_GCC -DHAVE_CONFIG_H -DPREFIX=\/usr\ -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/obj/amd64/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../cc_tools -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../cc_tools -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../../../../contrib/gcc -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../../../../contrib/gcc/config -c /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/contrib/gcc/gengenrtl.c cc -O -pipe -I. -static -DGENERATOR_FILE -DIN_GCC -DHAVE_CONFIG_H -DPREFIX=\/usr\ -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/obj/amd64/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../cc_tools -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../cc_tools -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../../../../contrib/gcc -I/vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools/../../../../contrib/gcc/config -o gengenrtl gengenrtl.o ./gengenrtl genrtl.c ./gengenrtl: 14: Syntax error: end of file unexpected (expecting )) *** Error code 2 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc/cc_tools. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin/cc. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu/usr.bin. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src/gnu. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src. *** Error code 1 Stop in /vol/vol0/users/des/tinderbox/CURRENT/amd64/amd64/src. TB --- 2003-07-12 05:34:07 - /usr/bin/make returned exit code 1 TB --- 2003-07-12 05:34:07 - ERROR: failed to build world TB --- 2003-07-12 05:34:07 - tinderbox aborted ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to [EMAIL PROTECTED]