Anyone have any ideas here?
On 1/13/06, Aaron Burruss [EMAIL PROTECTED] wrote:
Hi there,
I'm looking for some help on a problem I'm having with a new setup I've
got... I'm running sparc64 6.0 and also have an external USB drive
enclosure with a 250GB IDE drive in it. The drive is formatted as a BSD
partition (formatting done on another box).
I've got the following in my kernel:
# USB support
device uhci # UHCI PCI-USB interface
device ohci # OHCI PCI-USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # Human Interface Devices
device umass # Disks/Mass storage - Requires scbus and da
I.m seeing this in dmesg:
[EMAIL PROTECTED] dmesg |grep -i umass
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
[EMAIL PROTECTED] dmesg|grep -i usb
ohci0: Sun PCIO-2 USB controller mem 0xe200-0xe2007fff at device
12.3 on pci1
usb0: OHCI version 1.0, legacy support
usb0: Sun PCIO-2 USB controller on ohci0
usb0: USB revision 1.0
ohci1: Sun PCIO-2 USB controller mem 0xe500-0xe5007fff at device 5.3on
pci1
usb1: OHCI version 1.0, legacy support
usb1: Sun PCIO-2 USB controller on ohci1
usb1: USB revision 1.0
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
usbdevs shows:
[EMAIL PROTECTED] usbdevs -v
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, OHCI root hub(0x),
(0x108e)(0x), rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x),
(0x108e)(0x), rev 1.00
port 1 addr 2: full speed, self powered, config 1, product 0x0702(0x0702),
vendor 0x05e3(0x05e3), rev 0.33
port 2 powered
port 3 powered
port 4 powered
My primary hard drives are da0 and da1 (all the how-to's say that daX
should be where I mount.. but /dev only has my two primary drives:
-su-2.05b# ls -la /dev/da*
crw-r- 1 root operator 4, 16 Dec 20 20:11 /dev/da0
crw-r- 1 root operator 4, 18 Dec 20 12:11 /dev/da0a
crw-r- 1 root operator 4, 19 Dec 20 20:11 /dev/da0b
crw-r- 1 root operator 4, 20 Dec 20 20:11 /dev/da0c
crw-r- 1 root operator 4, 17 Dec 20 20:11 /dev/da1
crw-r- 1 root operator 4, 21 Dec 20 20:11 /dev/da1c
crw-r- 1 root operator 4, 22 Dec 20 12:11 /dev/da1d
-su-2.05b# dmesg|grep da.:
da0: FUJITSU MAN3367M SUN36G 1502 Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C)
da1: FUJITSU MAN3367M SUN36G 1502 Fixed Direct Access SCSI-2 device
da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
da1: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C)
I can plug this into my AMD64 running FreeBSD 6, and it comes up with no
problems.
I THINK I'm probably missing something totally dumb... Anyone got any help
for me on this?
Yah.. I know.. get an i386 box with IDE drives. :) This is a small 1U
box, and fits in my closet well. so I'd like to use it if possible.
Thanks!!!
Aaron
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
