Re: Networking IP Address Issues : NetBSD on Xen VM
On 04-Jul-2012, at 10:22 AM, dhaneshk k wrote: List, Please ignore my previous mail with the same subject line because there was a terrible formatting mistake. Please see the attached pdf which briefs the problem in assigning the IP address to the netbsd virtual machine. The Xen VM is running on Debian/ GNU Linux. I am assuming you are trying to get a bridge setup working. What is the bridge configuration in dom0? On a separate note, your email still is not proper. Learn to put contents in an email rather describing your problem in a PDF. Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 From: sub...@80386.org Date: Wed, 4 Jul 2012 00:06:56 +0530 To: dhanes...@hotmail.com CC: freebsd-questions@freebsd.org Subject: Re: Networking IP Address Issues : NetBSD on Xen VM On 03-Jul-2012, at 12:34 PM, dhaneshk k wrote: The Same problems discussed here were faced. Any hints to solve these issues much appreciated. No hints till you learn how to format your email properly, a basic requirement when posting to a mailing list. Thank you You are welcome. Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org NETBSD-AS-A-VIRTUAL-MACHINE-IPAddress_Issues.pdf___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Tweetless
On 04-Jul-2012, at 1:59 AM, Lars Eighner wrote: On Wed, 4 Jul 2012, Subhro Sankha Kar wrote: Hello, On 03-Jul-2012, at 9:14 PM, Tobias Rehbein wrote: Am Tue, Jul 03, 2012 at 01:04:07AM -0500 schrieb Lars Eighner: Call me crazy, but it seems that since the perl bump (5.12 - threaded-5.16) when firefox (13.0.1,1) got rebuilt, it seems twitter pages do not fully load, give me the slow loading banner, and the page (not browser or X) freezes, but no such problems were evident before, and twitter seems entirely normal in Opera 12.00. Disabling SPDY in about:config (a solution proposed on the net) didn't fix this issue. Another thing that doesn't work is rebuilding firefox from the ground up with portupgrade -fR firefox. Where does it burp? Can you post, say, the last 10-15 lines of the compile? Can you post the contents of about:config and also try to launch FF from command line and see if there is anything interesting reported back? Also, I hope you do not have any funky CFLAGS set in your make.conf? Of course firefox will not run from the command line (Error: no display specified), but there are no messages as firefox fails repeated to load twitter pages fully when firefox is launched in an xterm. Sorry for the ambiguity, I indeed meant to launch FF from xterm (or some equivalent Terminal Emulator in X) and report back the error. But since you say there is no problem with that, guess things should be good. make.conf: QT4_OPTIONS= CUPS WITH_GCC = yes # added by use.perl 2012-07-03 02:17:12 PERL_VERSION=5.16.0 This looks pretty generic, so nothing to complain about. I hate GUIs, so my mouse-fu skills are not good enough to copy about.config, but here is a save as snip Okay, try this out. Go to preferences and disable hardware acceleration. Also go to about:config and search for gfx. Set the property gfx.direct2d.disabled to true. Bounce the browser and go to about:support. At the bottom of the page, GPU Accelerated Windows should read 0/1. See if that makes a difference. Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Tweetless
On 04-Jul-2012, at 7:44 PM, Lars Eighner wrote: On Wed, 4 Jul 2012, Subhro Sankha Kar wrote: On 04-Jul-2012, at 1:59 AM, Lars Eighner wrote: On Wed, 4 Jul 2012, Subhro Sankha Kar wrote: Hello, On 03-Jul-2012, at 9:14 PM, Tobias Rehbein wrote: Am Tue, Jul 03, 2012 at 01:04:07AM -0500 schrieb Lars Eighner: Call me crazy, but it seems that since the perl bump (5.12 - threaded-5.16) when firefox (13.0.1,1) got rebuilt, it seems twitter pages do not fully load, give me the slow loading banner, and the page (not browser or X) freezes, but no such problems were evident before, and twitter seems entirely normal in Opera 12.00. Disabling SPDY in about:config (a solution proposed on the net) didn't fix this issue. Let us for a minute assume that there is nothing wrong with FF. How about installing Firebug and see in the Net tab that what precisely is happening when you load the Twitter main page? Is it waiting for apparently no reason at a particular place? Also, not strictly required, but can you also pass the traffic through something like LiveHTTPHeaders and post a traffic dump? As a third step, run a pcap session and see what is happening on the wire/air ? Adapter Description GLXtest process failed (exited with status 1): GLX version older / than the required 1.3 WebGL Renderer: Blocked for your graphics card because of unresolved driver issues. GPU Accelerated Windows: 0. Blocked for your graphics driver version. / Try updating your graphics driver to version / Anything with EXT_texture_from_pixmap support or newer. This probably means that none of the advanced rendering stuff work on your X setup. The only drivers that work with this machine (Intel G33) are intel and vesa. The intel driver does occasionally freeze X entirely requiring a boot, but this is not what happens when trying to load twitter pages. This is a completely distinct problem but probably it would be interesting to try and figure out why Graphics Acceleration is not working. I have very limited experience with Intel Graphics chipsets. In the i915 days, there used to be something called AIGLX which required some explicit configuration in xorg.conf. Could you check on that? Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Tweetless
Hello, On 03-Jul-2012, at 9:14 PM, Tobias Rehbein wrote: Am Tue, Jul 03, 2012 at 01:04:07AM -0500 schrieb Lars Eighner: Call me crazy, but it seems that since the perl bump (5.12 - threaded-5.16) when firefox (13.0.1,1) got rebuilt, it seems twitter pages do not fully load, give me the slow loading banner, and the page (not browser or X) freezes, but no such problems were evident before, and twitter seems entirely normal in Opera 12.00. Disabling SPDY in about:config (a solution proposed on the net) didn't fix this issue. Can you post the contents of about:config and also try to launch FF from command line and see if there is anything interesting reported back? Also, I hope you do not have any funky CFLAGS set in your make.conf? Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Networking IP Address Issues : NetBSD on Xen VM
On 03-Jul-2012, at 12:34 PM, dhaneshk k wrote: The Same problems discussed here were faced. Any hints to solve these issues much appreciated. No hints till you learn how to format your email properly, a basic requirement when posting to a mailing list. Thank you You are welcome. Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: FreeBSD 9.0 hang
On 03-Jul-2012, at 11:45 AM, Doug Hardie wrote: On 2 July 2012, at 22:59, Wojciech Puchar wrote: I have no ATM interfaces so it shouldn't be loading to my way of thinking. so check while this module is loading at all, no matter if it's unsuccessull. FreeBSD is not random place like windows, everything must have a reason. True it must, but I have no idea why if_en would try to be loaded or even how to figure that out. There is nothing in the logs. My understanding is that you would have to have an interface that requires the en driver. pciconf doesn't show any. How about a verbose boot and a list of your boot messages? Also, how about you create a kernel with ATM missing and see what stops working? Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: openoffice doesn't work - any ideas?
Hello, On 20-May-2012, at 3:00 AM, User Wojtek wrote: the problem is that what i found is not this. all description i found is that deleting .openoffice* from $HOME fixes it. it doesn't. i even created new user with no leftover any config files and still same. Are your ports up to date? Also, did you apply any funky compile time flags? Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On Sat, 19 May 2012, lokada...@gmx.de wrote: On 05/19/12 13:24, User Wojtek wrote: [wojtek@wojtek ~/robod]$ openoffice-3.4.0 [Java framework] Error in function createSettingsDocument (elements.cxx).javaldx failed! terminate called after throwing an instance of 'com::sun::star::uno::RuntimeException' compiled fine, installed without problems jdk 1.6 too. any ideas? thanks ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org Google find many things with javaldx failed. Is a problem with java, but different solutions (wrong xml, home permission, java- version ...). Hope you find a solution. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: can't kill -9 Xorg
On 12-Jun-2012, at 1:54 PM, Anton Shterenlikht wrote: On Tue, Jun 12, 2012 at 09:13:06AM +0100, Anton Shterenlikht wrote: On Tue, Jun 12, 2012 at 12:07:06AM +0530, Subhro Sankha Kar wrote: Hello What happens if you run without a xorg.conf? Xorg has become pretty good at guessing correct settings these days. No change. I removed /etc/X11/xorg.conf completely. Anyway, I can understand my X setup is fucked, no problem. Okay. That is kind of odd. But I am assuming you figured out what the precise problem is. What worries me more is the the fact that a process ignores kill -9. Doesn't it indicate a problem with the OS? I think potentially this is a security vulnerability. No not really. There are instances when a process can ignore SIGKILL or kill -9 as colloquially stated. For example, when a process in in the state of an uninterruptible sleep, marked as D in the top output, it will ignore all signals. Similarly for processes which are zombies, showing up as Z in the top output, will ignore the SIGKILL as well. Ideally, if you think you are hitting on a case where the process is not an uninterruptible state and still refuses to listen to SIGKILL, you should attach a strace or dtrace session to the process and see what is going on. Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 # X X.Org X Server 1.7.7 Release Date: 2010-05-04 X Protocol Version 11, Revision 0 Build Operating System: FreeBSD 10.0-CURRENT amd64 Current Operating System: FreeBSD mech-aslap239.men.bris.ac.uk 10.0-CURRENT FreeBSD 10.0-CURRENT #0 r236740M: Sat Jun 9 22:35:49 BST 2012 r...@mech-aslap239.men.bris.ac.uk:/usr/obj/usr/src/sys/BUZI amd64 Build Date: 11 June 2012 12:11:20PM Current version of pixman: 0.24.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: /var/log/Xorg.0.log, Time: Tue Jun 12 09:10:17 2012 (==) Using default built-in configuration (30 lines) (EE) Failed to load module vesa (module does not exist, 0) (EE) Failed to load module fbdev (module does not exist, 0) XRANDR name: VGA-0 Connector: VGA CRT1: INTERNAL_KLDSCP_DAC1 DDC reg: 0x7e50 XRANDR name: LVDS Connector: LVDS LCD1: INTERNAL_LVTM1 DDC reg: 0x7e40 Dac detection success finished output detect: 0 finished output detect: 1 finished all detect Dac detection success Output LCD1 disable success Blank CRTC 0 success Disable CRTC 0 success Blank CRTC 1 success Disable CRTC 1 success Output CRT1 disable success Output LCD1 disable success Blank CRTC 0 success Disable CRTC 0 success Blank CRTC 1 success Disable CRTC 1 success ^C^C^C Can kill it with neither CTRL/C nor kill -9: # ps ax|grep X 1060 0 R+ 0:38.95 X (Xorg) 1073 1 R+ 0:00.01 grep X # kill -9 1060 # ps ax|grep X 1060 0 RE+ 0:45.71 X (Xorg) 1089 1 R+ 0:00.00 grep X # Anton Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On 11-Jun-2012, at 5:01 PM, Anton Shterenlikht wrote: My X is unusable since the recent png update. This is r236740M on HP Compaq 6715s amd64 laptop. I've no hal installed (if this matters). # pkg info -x xorg linux-f10-xorg-libs-7.4_1 Xorg libraries (Linux Fedora 10) xorg-cf-files-1.0.4X.org cf files for use with imake builds xorg-fonts-7.5.1 X.org fonts meta-port xorg-fonts-100dpi-7.5.1X.Org 100dpi bitmap fonts xorg-fonts-75dpi-7.5.1 X.Org 75dpi bitmap fonts xorg-fonts-cyrillic-7.5.1 X.Org Cyrillic bitmap fonts xorg-fonts-miscbitmaps-7.5.1 X.Org miscellaneous bitmap fonts xorg-fonts-truetype-7.5.1 X.Org TrueType fonts xorg-fonts-type1-7.5.1 X.Org Type1 fonts xorg-libraries-7.5.1 X.org libraries meta-port xorg-macros-1.16.1 X.Org development aclocal macros xorg-server-1.7.7_5,1 X.Org X server and related programs # # pkg info -x xf86 libXxf86dga-1.1.2 X DGA Extension libXxf86misc-1.0.3 X XF86-Misc Extension libXxf86vm-1.1.1 X Vidmode Extension xf86-input-keyboard-1.6.1 X.Org keyboard input driver xf86-input-mouse-1.7.1 X.Org mouse input driver xf86-video-ati-6.14.3_1X.Org ati display driver xf86bigfontproto-1.2.0 XFree86-Bigfont extension headers xf86dgaproto-2.1 XFree86-DGA extension headers xf86driproto-2.1.1 XFree86-DRI extension headers xf86miscproto-0.9.3XFree86-Misc extension headers xf86vidmodeproto-2.3.1 XFree86-VidModeExtension extension headers # My xorg.conf.new: Section ServerLayout Identifier X.org
Re: can't kill -9 Xorg
Hello What happens if you run without a xorg.conf? Xorg has become pretty good at guessing correct settings these days. Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On 11-Jun-2012, at 5:01 PM, Anton Shterenlikht wrote: My X is unusable since the recent png update. This is r236740M on HP Compaq 6715s amd64 laptop. I've no hal installed (if this matters). # pkg info -x xorg linux-f10-xorg-libs-7.4_1 Xorg libraries (Linux Fedora 10) xorg-cf-files-1.0.4X.org cf files for use with imake builds xorg-fonts-7.5.1 X.org fonts meta-port xorg-fonts-100dpi-7.5.1X.Org 100dpi bitmap fonts xorg-fonts-75dpi-7.5.1 X.Org 75dpi bitmap fonts xorg-fonts-cyrillic-7.5.1 X.Org Cyrillic bitmap fonts xorg-fonts-miscbitmaps-7.5.1 X.Org miscellaneous bitmap fonts xorg-fonts-truetype-7.5.1 X.Org TrueType fonts xorg-fonts-type1-7.5.1 X.Org Type1 fonts xorg-libraries-7.5.1 X.org libraries meta-port xorg-macros-1.16.1 X.Org development aclocal macros xorg-server-1.7.7_5,1 X.Org X server and related programs # # pkg info -x xf86 libXxf86dga-1.1.2 X DGA Extension libXxf86misc-1.0.3 X XF86-Misc Extension libXxf86vm-1.1.1 X Vidmode Extension xf86-input-keyboard-1.6.1 X.Org keyboard input driver xf86-input-mouse-1.7.1 X.Org mouse input driver xf86-video-ati-6.14.3_1X.Org ati display driver xf86bigfontproto-1.2.0 XFree86-Bigfont extension headers xf86dgaproto-2.1 XFree86-DGA extension headers xf86driproto-2.1.1 XFree86-DRI extension headers xf86miscproto-0.9.3XFree86-Misc extension headers xf86vidmodeproto-2.3.1 XFree86-VidModeExtension extension headers # My xorg.conf.new: Section ServerLayout Identifier X.org Configured Screen 0 Screen0 0 0 InputDeviceMouse0 CorePointer InputDeviceKeyboard0 CoreKeyboard Option AllowEmptyInput Off EndSection Section Files ModulePath /usr/local/lib/xorg/modules FontPath /usr/local/lib/X11/fonts/misc/ FontPath /usr/local/lib/X11/fonts/TTF/ FontPath /usr/local/lib/X11/fonts/OTF FontPath /usr/local/lib/X11/fonts/Type1/ FontPath /usr/local/lib/X11/fonts/100dpi/ FontPath /usr/local/lib/X11/fonts/75dpi/ EndSection Section Module Load extmod Load record Load dbe Load glx Load dri Load dri2 EndSection Section InputDevice Identifier Keyboard0 Driver kbd EndSection Section InputDevice Identifier Mouse0 Driver mouse Option Protocol auto Option Device /dev/sysmouse Option ZAxisMapping 4 5 6 7 EndSection Section Monitor #DisplaySize 330 210 # mm Identifier Monitor0 VendorName LPL ModelNamed600 EndSection Section Device Identifier Card0 Driver radeon VendorName Advanced Micro Devices [AMD] nee ATI BoardName RS690M [Radeon X1200 Series] BusID PCI:1:5:0 Option int10 on Option BusType PCIE Option RenderAccel on Option AccelMethod xaa Option DynamicPM on Option DRI on EndSection Section Screen Identifier Screen0 Device Card0 MonitorMonitor0 SubSection Display Viewport 0 0 Depth 1 EndSubSection SubSection Display Viewport 0 0 Depth 4 EndSubSection SubSection Display Viewport 0 0 Depth 8 EndSubSection SubSection Display Viewport 0 0 Depth 15 EndSubSection SubSection Display Viewport 0 0 Depth 16 EndSubSection SubSection Display Viewport 0 0 Depth 24 EndSubSection EndSection The Xorg.0.log: X.Org X Server 1.7.7 Release Date: 2010-05-04 X Protocol Version 11, Revision 0 Build Operating System: FreeBSD 10.0-CURRENT amd64 Current Operating System: FreeBSD mech-aslap239.men.bris.ac.uk 10.0-CURRENT FreeBSD 10.0-CURRENT #0 r236740M: Sat Jun 9 22:35:49 BST 2012 r...@mech-aslap239.men.bris.ac.uk:/usr/obj/usr/src/sys/BUZI amd64 Build Date: 11 June 2012 12:11:20PM Current version of pixman: 0.24.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: /var/log/Xorg.0.log, Time: Mon Jun 11 12:24
Re: mysqld startup issue
On 11-Jun-2012, at 11:02 PM, Gary Aitken wrote: I've done the following after having a running system with a running mysql on it: moved user accounts, although no logical move: /usr/home/foo was = /hd1/foo now /usr/home = /hd1/home and /hd1/foo is now /hd1/home/foo repartitioned the SSD and restored the system from a dump taken prior to repartitioning. removed all ports and reinstalled them Unfortunately, mysqld won't start: 120611 10:55:52 [Warning] Can't create test file /var/db/mysql/breakaway.lower-test What's the permission of /var/db/mysql? Also what user is mysql running as? Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 120611 10:55:52 [Warning] Can't create test file /var/db/mysql/breakaway.lower-test mysqld: Table 'mysql.plugin' doesn't exist 120611 10:55:52 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 120611 10:55:52 InnoDB: The InnoDB memory heap is disabled 120611 10:55:52 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120611 10:55:52 InnoDB: Compressed tables use zlib 1.2.5 120611 10:55:52 InnoDB: Initializing buffer pool, size = 128.0M 120611 10:55:52 InnoDB: Completed initialization of buffer pool 120611 10:55:52 InnoDB: Operating system error number 13 in a file operation. InnoDB: The error means mysqld does not have the access rights to InnoDB: the directory. InnoDB: File name ./ibdata1 InnoDB: File operation call: 'create'. InnoDB: Cannot continue operation. Running mysqld --verbose shows: basedir /usr/local general-log-file/var/db/mysql/breakaway.log ls -aol /usr/local/libexec/mysqld -rwxr-xr-x 1 root wheel - 9558944 Jun 11 10:40 /usr/local/libexec/mysqld ls -dl /var/db/mysql drwxr-xr-x 2 mysql mysql 512 Jun 11 10:31 /var/db/mysql cd / find . -ls | grep my.cnf shows nothing. This looks like some kind of access / setuid problem, but I'm not sure what. Suggestions? ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Chromium Crashes
Hello, On 10-Jun-2012, at 11:40 AM, The Todds wrote: Yes this is the latest build (5th June) of Chromium. I suppose I could revert to the 18.0.1025.168 version using portdowngrade until this fault is fixed. Glenn It looks like the port is lagging back from mainstream. You could also write to the maintainers. I am copying the maintainers just in case someone is already on it. Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On Sun, 2012-06-10 at 10:37 +0530, Subhro Sankha Kar wrote: Hello, It looks like you have hit a documented bug. See this: http://code.google.com/p/chromium/issues/detail?id=125447 http://src.chromium.org/viewvc/chrome?view=revrevision=141116 Did you try upgrading your ports? Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On 10-Jun-2012, at 10:11 AM, The Todds wrote: I have just have built and installed Chromium 19.0.1084.52 from the ports on my amd64 machine - 8.2-STABLE FreeBSD 8.2-STABLE #0: Sat Nov 5 08:40:03 NZDT 2011 Portversion chromium-19.0.1084.52_2 = up-to-date with port On web sites which contains graphics Chromium crashes with the following error: [3152:171983296:14310963010:ERROR:CONSOLE(1)] Uncaught ReferenceError: ntp is not defined, source: (1) Any ideas how to resolve this issue. Glenn ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: ports: make config-recursive doesn't really
You can have a look at port-mgmt/portmaster. Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On 10-Jun-2012, at 10:07 PM, Gary Aitken wrote: I'm trying to build a script to rebuild and reinstall everything I have installed from ports. I don't want to have to keep checking on it and filling out the appropriate check boxes for options. I naively assumed: for port in $ports do cd /usr/port/$port make config-recursive cd ../.. done would allow me to set up all the dependencies before continuing with the install. It appears, however, that it doesn't really recurse properly. I say appears only because this is my first time trying this and despite doing the above setting of options, I am confronted with additional options screens as the build progresses. Is there a way to get around this? Thanks, Gary ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Firefox Script Problems
Hello Sean, Can you run FF from a terminal and report back what you see? Thanks -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On 11-Jun-2012, at 1:44 AM, sean wrote: Hello All, I just upgraded Firefox to the latest available in ports. Since this upgrade Firefox is near unresponsive. Messages keep popping up about unresponsive script errors on the page being viewed. Would anyone have any ideas on how to best approach this problem to find the fix? Thanks in advance, Sean ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: link_elf_obj: symbol ata_controlcmd undefined
Hello, Looks like you have missed out something related to ATA in the kernel configuration file. Can you post your complete kernel config? Thanks Subhro -- Subhro Sankha Kar System Administrator Working and playing with FreeBSD since 2002 On 20-May-2012, at 5:53 PM, C. P. Ghost wrote: Hello, what does this boot message means, and where does it come from? link_elf_obj: symbol ata_controlcmd undefined linker_load_file: Unsupported file type It appears between between ZFS storage pool version 28 and drm0: ATI Radeon HD 3200 Graphics on vgapci0 uname -a: FreeBSD phenom.cordula.ws 9.0-STABLE FreeBSD 9.0-STABLE #0 r235604: Fri May 18 15:49:06 CEST 2012 r...@phenom.cordula.ws: /usr/obj/usr/src/sys/GENERIC amd64 TIA, -cpghost. -- Cordula's Web. http://www.cordula.ws/ ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Chromium Crashes
Hello, It looks like you have hit a documented bug. See this: http://code.google.com/p/chromium/issues/detail?id=125447 http://src.chromium.org/viewvc/chrome?view=revrevision=141116 Did you try upgrading your ports? Thanks Subhro -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002 On 10-Jun-2012, at 10:11 AM, The Todds wrote: I have just have built and installed Chromium 19.0.1084.52 from the ports on my amd64 machine - 8.2-STABLE FreeBSD 8.2-STABLE #0: Sat Nov 5 08:40:03 NZDT 2011 Portversion chromium-19.0.1084.52_2 = up-to-date with port On web sites which contains graphics Chromium crashes with the following error: [3152:171983296:14310963010:ERROR:CONSOLE(1)] Uncaught ReferenceError: ntp is not defined, source: (1) Any ideas how to resolve this issue. Glenn ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: ran out of inodes on /var, recommended value?
On 10-Jun-2012, at 6:13 AM, ill...@gmail.com wrote: On 9 June 2012 18:38, RW rwmailli...@googlemail.com wrote: On Sat, 09 Jun 2012 07:22:50 -0600 Gary Aitken wrote: I reconfigured my ssd filesystem with the /var partition of size 512M. Unfortunately, something in portsnap or the ports tree in general uses a boatload of small files, and i ran out of inodes. Can anyone recommend an appropriate size for the newfs -i value? 1024? less? portsnap needs roughly one file per port plus one for each out of date port during a fetch. There are 23658 ports. In FreeBSD 9 the fragment size increased, halving the default number of inodes. With only 32k inodes it's possible to run out with portsnap alone. You can probably get away with the old default of 64k (-i 8192), or perhaps 128k (-i 4096). Check how many files you have outside of portsnap and do the arithmetic. Or, move the portsnap tree to somewhere other than /var (see /etc/portsnap.conf for that such). I think that a file-backed md* mounted only when portsnap was in use would save on inodes, yeah? Actually I think that is a very good idea. That is how I have set up my system as well with one difference. I have tons of memory and use a memory based filesystem to store all the in-compile objects. -- Subhro Sankha Kar System Administrator Working and Playing with FreeBSD since 2002___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: mount /unmount
Hello, You seem to be new to FreeBSD. In that case , I would recommend you to read the Handbook. It is very very good documentation. On 04-Jul-2011, at 5:58 PM, tethys ocean wrote: Hi, I have 3 question is FreeBSD can boot and run all service while one of slice is not mount for example /usr slice.. Yes, FreeBSD can run off a single filesystem. and second question is my mysql is in /var slice if /var is not mout can I access mysql being root and chek all databases also can read log file on /var If /var is on separate filesystem, then there is no way you can access anything inside /var without mounting /var first. third question is can I mount any unmount slice by using just fsck :) fsck is a utility which is used to check filesystem for consistency. For mounting a filesystem you should be using /sbin/mount and for unmounting you should use /sbin/unmount. Thanks Subhro
Re: Best RAID setup
On 26-Jan-2011, at 6:26 AM, Don O'Neil wrote: I'm getting ready to setup a new FreeBSD 8.1 64 bit server and wanted to know everyone's thoughts on which way to go. software RAID 5 (or 10) or hardware RAID 5 (or 10). If you need to select between software and hardware RAID, then by all means go for hardware RAID. RAID 10 is always faster than RAID5 and the difference really stands out when writing data. I currently have a 3Ware card in one of my servers and it works great, but I haven't really been keeping up on what the latest RAID support is. All RAID cards (that I have come across) support both RAID 10 and RAID5. So there is a fair chance that your card will not disappoint you. How is the ZFS support these days? Is it production ready? ZFS is fine. I use it on my prod boxes and so far there have been no issues. What about hardware RAID, is there a compatibility list somewhere with what hardware (or pseudo hardware) RAID controllers are supported? Didn't get this question though. I'm just looking for the most stable, and production ready RAID that can handle at least 1 TB disks and create volumes in the 3-4 TB range. Any thoughts, feedback, caveats, etc. are welcomed. You need to RTFM. Thanks -- Subhro Kar Visit my Blog: http://blog.80386.org ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Get access to csh (default freebsd shell) for root to solve login problem.
On 04-Jul-2010, at 9:48 PM, Thomas Keusch wrote: On Sun, Jul 04, 2010 at 05:02:59PM +0100, Luca Renaud wrote: Hi, The root shell is now bash,but I was unaware that bash was not self-contained(it depends at least of libintl.so.8), and doing some upgrades with ports I erased libintl.so.8,now I cannot access the root account because bash is not operational and I need root access to install again libintl.so.8,or any other way to solve the problem. So,how can I get access to csh for root without having access to a root shell(the previously defined bash does not work,and I need root access to change the shell for the root acount). if you haven't activated the 'toor' account (another UID 0 account besides root), you'll have to boot from fixit media (or another live cd / system) and go from there. I think that would be an overkill. From the su(1) manpage, -m Leave the environment unmodified. The invoked shell is your login shell, and no directory changes are made. As a security precaution, if the target user's shell is a non-standard shell (as defined by getusershell(3)) and the caller's real uid is non- zero, su will fail. So, you could use su -m to switch to root and remain in the same shell as your user calling su. Once there, AFAIK, you could use vipw(8) or chsh(1) to change the root shell back to csh. Thanks Subhro -- Subhro Kar Blog: http://80386.org Twitter: http://twitter.com/subhrokar FaceBook: http://www.facebook.com/subhrokar
Re: FreeBSD support for HP DL180/G5
HP produces pretty good boxes and historically I have been able to get them working without any troubles. However I would say DL180 is a pretty non customizable box. The hardware works perfectly with FreeBSD 7.0. I didnt try it with 6.3, so cant comment on that. However I would say DL380 is a better off. The main advantage of DL3xx boxes are there is a lot of room to play with add-on cards. Also not all the latest and greatest processors are available with DL1xx family of servers. Also make sure that you go for an external RAID controller like 3ware or Areca. I prefer Areca more :-D. The HP RAID controller cant take the beating I give to it. Thanks Subhro On Fri, Oct 10, 2008 at 1:55 AM, Josef Grosch [EMAIL PROTECTED]wrote: Does anyone have experience running FreeBSD 6.x and 7.x on an HP DL180/G5? The company I work for is looking to get a number of these to be put in production. Your general impressions would be a good start. Josef -- Josef Grosch | Another day closer to a | FreeBSD 6.3 [EMAIL PROTECTED] | Micro$oft free world | Berkeley, Ca. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Can't adduser using FreeBSD 7.0 (amd64)
Oops it should be pwd_mkdb instead of pw_mkdb so pwd_mkdb -p /etc/master.passwd Cheers again!! Subhro On Fri, Sep 12, 2008 at 2:52 PM, Subhro [EMAIL PROTECTED] wrote: pw_mkdb -p /etc/master.passwd Cheers! Subhro On Fri, Sep 12, 2008 at 2:09 PM, Froilan Romualdo [EMAIL PROTECTED] wrote: Here's my uname -a: FreeBSD fbsd.its1.localhost.com 7.0-RELEASE FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC amd64 Error upon running adduser: pwd_mkdb: 14 uid is incorrect pwd_mkdb: /etc/master.passwd: Inappropiate file type or format pw: user 'froilanr' disappeared during update adduser: ERROR: There was an error adding user (froilanr). NOTE: I already read the FreeBSD handbook and google search the problem, but I can't see a solution. Thank you in advance. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Can't adduser using FreeBSD 7.0 (amd64)
pw_mkdb -p /etc/master.passwd Cheers! Subhro On Fri, Sep 12, 2008 at 2:09 PM, Froilan Romualdo [EMAIL PROTECTED] wrote: Here's my uname -a: FreeBSD fbsd.its1.localhost.com 7.0-RELEASE FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC amd64 Error upon running adduser: pwd_mkdb: 14 uid is incorrect pwd_mkdb: /etc/master.passwd: Inappropiate file type or format pw: user 'froilanr' disappeared during update adduser: ERROR: There was an error adding user (froilanr). NOTE: I already read the FreeBSD handbook and google search the problem, but I can't see a solution. Thank you in advance. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: pf to block against DDoS?
What exactly are you looking for? Are you looking for example rulesets? Thanks Subhro On 9/5/08, Redd Vinylene [EMAIL PROTECTED] wrote: Hello hello! I was quite shocked today when I heard I could use pf to block against DDoS attacks, using Stateful Tracking Options, http://www.openbsd.org/faq/pf/filter.html#stateopts. But does anybody have any nice setups of this they'd want to share? Much obliged, and thanks. -- http://www.home.no/reddvinylene ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Sent from Gmail for mobile | mobile.google.com Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Wine security question...
man jail Thanks Subhro On Fri, Aug 29, 2008 at 8:16 AM, Christopher Joyner [EMAIL PROTECTED] wrote: Is it possible to use wine in a secure way? I had a warning about it after installing it from the ports. So I was wondering if it's possible to limit it to a certain area. Like a sandbox? In Love in Jesus Christ, Or Lord and Savior. For God so loved the world, that he gave his only *begotten Son, that whosoever believeth in him should not perish, but have everlasting life. --John 3:16 ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Network, routers, DHCP and PXE
Just to add to that suggestion, if you have a separate DHCP server, make sure your router works as a DHCP client for the internal network as well. You should be able to do that by telnetting into the management port. You may use a serial cable as well. This is required in order to get the NAT working properly. Thanks Subhro On Mon, Jul 28, 2008 at 1:18 PM, Manolis Kiagias [EMAIL PROTECTED] wrote: Svein Halvor Halvorsen wrote: Hi, list! I have a private home network, on an ADSL2+ connection to the internet. The home network is behind NAT, all automatically set up by the router/dhcp server/wlan access point/adsl modem that I got from my ISP. It's a Thomson SpeedTouch 585 router. Now, on this network, most of the computers get their IP by means of DHCP. Except our home audio server, which have a hard coded ip address in rc.conf, set to something within the range of the dhcp server (10.0.0.2-10.0.0.253). The server seems to pick this up, and don't give that address away to someone else. You may also want to ensure that the router will never allocate your static IP address to someone else. Look at the DHCP router settings either for DHCP scope (set it to narrower values, and use a static IP outside the range) or for something like exceptions / exclusion where you can mark a specific IP that DHCP will never assign. I've tried using other addresses outside this range, like 10.0.1.1, but that doesn't work. All network access is lost when I do that. 10.0.1.1 is a different network (I assume your netmask is 255.255.255.0, but check your router or your clients) Now, on my local network I'd like to put a diskless machine. As I understand it, my DHCP server needs to tell the client about the filename and a next-server to use. I don't think I can setup the Thomson router to do this. All the instruction I can find online advises me to install a DHCP server on the same machine that serves the pxe boot image. But if I do that, I'll get two DHCP servers on my local network. Is that ok? Will there be a race condition, when a client asks for an IP address? You will have to shutdown the router's DHCP. Probably disable it permanently and assign this function to a machine. The DHCP of the router also sends you the following information (besides IP address): - DNS Server(s): Either the ones used by your ISP (consult its website) or its own address (i.e. 10.0.0.1). Most routers send their own address as a DNS server and perform the resolution by sending your request to ISP servers. - Gateway address: This is always the router's local IP address (i.e. 10.0.0.1) If you setup your own DHCP server, make sure it is set to send this info as well. (These are commonly known as DHCP options) ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: setuid not working on directories, or am I doing something wrong?
Give me the output of 'mount' please. Thanks Subhro On Fri, Jul 25, 2008 at 5:15 PM, Bill Moran [EMAIL PROTECTED] wrote: $ whoami wmoran $ mkdir test2 $ sudo chown daemon:daemon test2 $ sudo chmod 6777 test2 $ ls -lah | grep test2 drwsrwsrwx 2 daemon daemon 512B Jul 25 07:40 test2 $ touch test2/testfile.empty $ ls -lah test2 total 8 drwsrwsrwx 2 daemon daemon 512B Jul 25 07:41 . drwxr-xr-x 59 wmoran wheel6.0K Jul 25 07:40 .. -rw-r--r-- 1 wmoran daemon 0B Jul 25 07:41 testfile.empty Shouldn't testfile.empty show up as daemon:daemon? or am I misunderstanding something about how setuid works? This is on FreeBSD 7, but I observe the same thing on 6.3 and 6.2. -- Bill Moran Collaborative Fusion Inc. http://people.collaborativefusion.com/~wmoran/ [EMAIL PROTECTED] Phone: 412-422-3463x4023 IMPORTANT: This message contains confidential information and is intended only for the individual named. If the reader of this message is not an intended recipient (or the individual responsible for the delivery of this message to an intended recipient), please be advised that any re-use, dissemination, distribution or copying of this message is prohibited. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system. E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail transmission. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- WC Fields - A rich man is nothing but a poor man with money. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: NFS drops with em0 driver
Thanks everyone for the replies so far. I have disabled ACPI on my boxes. However the drops still persist. I would be grateful if someone can provide more ideas. Thanks Subhro On Sun, Jun 1, 2008 at 2:17 PM, Catalin Miclaus [EMAIL PROTECTED] wrote: -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Subhro Sent: Sunday, June 01, 2008 7:06 AM To: freebsd-questions@freebsd.org Subject: NFS drops with em0 driver Hello, I am facing a strange problem on my systems. I am running FreeBSD-6.2-RELEASE-p12. My network interface uses the em driver. I am facing a lot of issues where the NFS connections are dying randomly. Is there any known bug with the em driver? I am using the SCHED_ULE scheduler. Thanks Subhro Check this: http://wiki.freebsd.org/JeremyChadwick/Commonly_reported_issues Best Regards Catalin Miclaus Network/Security ISP-Data Starcomms Ltd. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
NFS drops with em0 driver
Hello, I am facing a strange problem on my systems. I am running FreeBSD-6.2-RELEASE-p12. My network interface uses the em driver. I am facing a lot of issues where the NFS connections are dying randomly. Is there any known bug with the em driver? I am using the SCHED_ULE scheduler. Thanks Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Release Build
Hello everyone, I am trying to create a customized release build. The idea is to have a NFS export which can be used during installation over the network. My build box is running the same version of BSD(6.2) as the NFS export I intend to create. So instead of mirroring the cvs repository (bandwidth woes :-S) I am using /usr/src. I have built the release using make release CHROOTDIR=/tmp/release BUILDNAME=FreeBSD-custom-6.2 EXTSRCDIR=/usr/src EXTPORTSDIR=/usr/ports WORLD_FLAGS='-j16 -march=prescott' KERNEL_FLAGS='-j16 -march=prescott' -DNOPORTS -DNODOC RELEASETAG=RELENG_6_2 This had completed successfully with my newly built release in /tmp/release/R/. The next thing I did was to export the disc1 folder inside cdrom over NFS and try to boot over the network. I have checked that my netboot works using a CDROM as a NFS export. This time it locks up with Extracting packages. Any clues about where I should start looking?? Thanks Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Local package mirror
Hello Lowell, Thank you so much for the reply. I am trying to do the build once and use prebuilt packages for the target boxes. However the problem I am facing is a bit crude. Lets assume I am trying to build pkgA which has dependencies of pkgB and pkgC. The process I am following is cd /usr/ports/xxx/pkgA ; make package. This makes the prebuilt package in /usr/ports/ packages. However it does not case about pkgB which is a dependency. On a target system when I am trying to pkg_add it, it is rightly complaining about a missing dependency and also saying that it cant find the package in the local repository and aborting. How can this be taken care of? Thanks Subhro On Sat, Apr 5, 2008 at 6:26 PM, Lowell Gilbert [EMAIL PROTECTED] wrote: Subhro [EMAIL PROTECTED] writes: I am trying to get a Network install working on my local network. I have been able to successfully create a NFS export of the installation disk and perform a install from there. The target machines boot over PXE and fetch stuff from the NFS. However I am unable to figure out how to get the packages working. I have a list of about 180 packages which needs to be installed. But I am unable to figure out how to go about it. I would like to use precompiled packages, but the CD do not contain the packages I am looking for. One of the option is to mirror the whole package directory from the freebsd mirrors, but that story involves a lot of data transfer and bandwidth. Is there something obvious I am missing? Any help would be highly appreciated. There are a number of ways to do this general sort of thing. For the base system approach, with pkg_add(1), setting PACKAGEROOT (or possibly PACKAGESITE depending on exactly how you configure the server for network fetch, or PKG_PATH if the clients have the NFS directory mounted) should be good enough. On the other hand, the way I do it is to have a master server, where I build everything (or fetch everything, if I don't want to build it myself). Then the other machines mount /usr/ports from the master server. I use portupgrade to do the installs from the clients, which knows how to use packages when available locally and only fetch them if they aren't. I hope this helps. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Local package mirror
Hello, I am trying to get a Network install working on my local network. I have been able to successfully create a NFS export of the installation disk and perform a install from there. The target machines boot over PXE and fetch stuff from the NFS. However I am unable to figure out how to get the packages working. I have a list of about 180 packages which needs to be installed. But I am unable to figure out how to go about it. I would like to use precompiled packages, but the CD do not contain the packages I am looking for. One of the option is to mirror the whole package directory from the freebsd mirrors, but that story involves a lot of data transfer and bandwidth. Is there something obvious I am missing? Any help would be highly appreciated. Thanks Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Looking for IRC(chat) network with #freebsd channel (English language)
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 williamkow sat at his 'pewter and typed on 11/28/07 12:10: I have been trying to find a IRC/Chat network which has #FreeBSD channel (english), but could get one, although I have read the below links, but no help. how about irc.freenode.net? Subhro - -- = Subhro Kar Systems Engineer Yahoo! Inc. Torrey Pines Embassy Golf Links Business Park Off Koramangala - Challaghata Village Bangalore 560017 India Ph: +91-80-3077-3699 = _ / A bird in the bush usually has a friend \ \ in there with him. / - \ ^__^ \ (@@)\___ (__)\ )\/\ ||w | || || -BEGIN PGP SIGNATURE- Version: GnuPG v1.4.7 (GNU/Linux) iD8DBQFHTRBfDA+HioTWbkQRAot+AKDM0mVU0rr7RKldPSl64ZKm9dnxYgCg59gy wXqqmmdPVTUl+cL4Knrr+w4= =AGWF -END PGP SIGNATURE- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Cheaper backup mechnism for a server
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 Hello, dhaneshk k sat at his 'pewter and typed on 09/21/07 13:55: Hi ; A general question pls excuse me can any body suggest a backup mechanism for a server machine , which has a web portal , email server ,PgSQL database 4GB size , DNS server, Mailman , and a mediawiki applications running in a single machine . Can you suggest good solutions , for the server Backup mechanismso that I can restore all the data just before the crashing moment . pls share your expertise , it will help me lot to secure my data in the server machine .. If you wish to have 0 downtime then the only option is a separate failover server. However much you try, if you do not have a separate box to failover to, it is not possible to do a 0 downtime switchover. Regarding the backup solution, you can either buy an external Hard Disk and back up to it. Alternatively you can back up to tape drives or to NFS mounted volumes. Thanks Subhro - -- __ / The nice thing about Windows is - It \ | does not just crash, it displays a | | dialog box and lets you press 'OK' | \ first. (Arno Schaefer's .sig)/ -- \ ^__^ \ (@@)\___ (__)\ )\/\ ||w | || || -BEGIN PGP SIGNATURE- Version: GnuPG v1.4.7 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFG84dXDA+HioTWbkQRAu2RAKDJMztsQAu2oLuMaKt/vFEvf3YdewCgupn/ eozM9rJAJzKmkTSPSBA4oQc= =8sWc -END PGP SIGNATURE- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Cheaper backup mechnism for a server
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 Hello DharneshK, You can try to create a Mirror using RAID. You can either create a software or a hardware (recommended) managed Mirror. In case of a disk crash you still have a copy of the updated data on the disk. BTW, please make sure you hit Reply all instead of Reply. this also keeps the freebsd-questions@ updated which will allow others to look into this mail and provide a better answer as well as help future users. Thanks Subhro dhaneshk k sat at his 'pewter and typed on 09/21/07 14:39: Hi , subhro, i agree with you , I need a clarification The backup should be the uptodate one , so in case of a disk crash (permanent crash) I need the backup upto the last moment , so is ther any cheap tools , to do it , so i can save the backups to another desktop pc synchronously (I mean any mechanism for backup through online ie ; ssh OR VPN or like that ) (not manual backing up at each moment) can you tell the exact solution . If I am using rsync , I can only do it by a crontab , even though at a specfic time only the cron run , if crash occurs after this time then the data after the cron will lose , so which is the right cheaper solution ? From: Subhro Kar [EMAIL PROTECTED] To: dhaneshk k [EMAIL PROTECTED] CC: freebsd-questions@freebsd.org Subject: Re: Cheaper backup mechnism for a server Date: Fri, 21 Sep 2007 14:26:55 +0530 Hello, dhaneshk k sat at his 'pewter and typed on 09/21/07 13:55: Hi ; A general question pls excuse me can any body suggest a backup mechanism for a server machine , which has a web portal , email server ,PgSQL database 4GB size , DNS server, Mailman , and a mediawiki applications running in a single machine . Can you suggest good solutions , for the server Backup mechanismso that I can restore all the data just before the crashing moment . pls share your expertise , it will help me lot to secure my data in the server machine .. If you wish to have 0 downtime then the only option is a separate failover server. However much you try, if you do not have a separate box to failover to, it is not possible to do a 0 downtime switchover. Regarding the backup solution, you can either buy an external Hard Disk and back up to it. Alternatively you can back up to tape drives or to NFS mounted volumes. Thanks Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] _ Single,planning to marry? Find the right match @ shaadi.com http://ss1.richmedia.in/recurl.asp?pid=202 __ / The nice thing about Windows is - It \ | does not just crash, it displays a | | dialog box and lets you press 'OK' | \ first. (Arno Schaefer's .sig)/ -- \ ^__^ \ (@@)\___ (__)\ )\/\ ||w | || || -BEGIN PGP SIGNATURE- Version: GnuPG v1.4.7 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFG85AFDA+HioTWbkQRAgp1AJ4xZP+I9nblPoI53DTnSDtn+eBq/wCeMxY9 rx1uuX8ycwi3ETlB2hFqTIc= =e3cq -END PGP SIGNATURE- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Good FreeBSD Supported Gigabit Ethernet Card?
Oliver Hansen wrote: I'm looking to eventually upgrade my home network to all gigabit so I'm going to start by purchasing a few NICs for some old servers I just received. I know there are quite a few supported by FreeBSD6 which I found ( http://www.freebsd.org/releases/6.0R/hardware-i386.html#ETHERNET ) but I'm wondering if there is any real benefit in buying a $40 or $50 NIC like the Netgear GA311 or just get a $20 NIC like the D-Link DFE-530TX+. The use will probably be a firewall, proxy, file server, and DVR. http://www.EagleBit.com/Netgear_GA311_Gigabit_PCI_Card_p/eb-400-00357.htm No offence meant, but why would you like to upgrade a home network to Gbit? Is it required at all? Subhro _ / Life is difficult because it is \ \ non-linear. / - \ ^__^ \ (xx)\___ (__)\ )\/\ U ||w | || || ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Force a recompile
Hello, How do I force a recompile of all the ports installed on my system? Thanks Subhro -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Force a recompile
I was going through the man page of portupgade. Does portupgrade -af have the same effect? Thanks Subhro On 8/18/07, Gaye Abdoulaye Walsimou [EMAIL PROTECTED] wrote: Subhro a écrit : Hello, How do I force a recompile of all the ports installed on my system? Thanks Subhro #pkg_add -r portmanager #portmanager -u -f Regards -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Frequency Stepping crashing Notebook
Hello, I am running FreeBSD 6-STABLE on my notebook which is a HP nc6400. Everything was working fine till I enabled powerd to dynamiacally manage the CPU frequency. Since then the system has been crashing with 3 mins of completing booting. There is not errors indicated in the system log. Is there any known issues? Thanks Subhro -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: CRT value Absurd
Hello, On 8/3/07, Andrew Greenwood [EMAIL PROTECTED] wrote: Jonathan Horne wrote: On Thursday 02 August 2007 13:13:46 Subhro wrote: FreeBSD on this. My system boots up fine but I am repeatedly getting Errors from ACPI. I am repeatedly getting acpi_tz0: _CRT value is absurd, ignored (256C) How can I solve this problem? I had a similar problem on an HP Pavilion (don't remember the exact model) and I could only get the messages to stop by entering hw.acpi.thermal.polling_rate=0 I have tried to follow the same process. Although the sysctl value changes, the messages keep on coming in. BTW, does things like cpu speed stepping, sleep, hibernate etc work? Thanks Subhro -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
CRT value Absurd
Hello Folks, Recently I got a HP nc6400 notebook for myself and decided to install FreeBSD on this. My system boots up fine but I am repeatedly getting Errors from ACPI. I am repeatedly getting acpi_tz0: _CRT value is absurd, ignored (256C) How can I solve this problem? Thanks Subhro -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: CRT value Absurd
Hello Jonathan, This particular notebooks is shipped with a Intel 945 GM chipset which is known to have an incompaitbility with Xorg 7.2. However along with 915-resolution present in the ports, things work perfectly. Thanks Subhro On 8/3/07, Jonathan Horne [EMAIL PROTECTED] wrote: On Thursday 02 August 2007 13:13:46 Subhro wrote: Hello Folks, Recently I got a HP nc6400 notebook for myself and decided to install FreeBSD on this. My system boots up fine but I am repeatedly getting Errors from ACPI. I am repeatedly getting acpi_tz0: _CRT value is absurd, ignored (256C) How can I solve this problem? Thanks Subhro subhru, how is the rest of the install working? we have a lot of 6400s here at my office, and when i tried to install the xorg7.2 ports, i couldnt get xorg to start, and i was wondering how it was going for you. -- Jonathan Horne http://dfwlpiki.dfwlp.org [EMAIL PROTECTED] ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Software Engineer Dynamic Digital Technologies Pvt. Ltd. EPY-3, Sector: V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Xorg
Hello Folks, I would like to know which is the latest version of Xorg present in the ports tree. The one I can find in 6.9. However the latest version present on the Xorg homepage is 7.1 which was release on May 22, 2006. Has it been ported to the ports tree yet? If not when can it be expected to be done. Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Acroread not working
Hello Michael, Thank for writing back. On 10/16/06, Michael S [EMAIL PROTECTED] wrote: My setup is quite similar: linux-XFree86-libs-4.3.99.902_7 XFree86 libraries, Linux binary linux-aspell-0.50.4.1_1 Spelling checker with better logic than ispell (linux versi linux-atk-1.9.1 Accessibility Toolkit, Linux/i386 binary linux-expat-1.95.8 Linux/i386 binary port of Expat XML-parsing library linux-flashplugin-7.0r63_1 Adobe Flash Player NPAPI Plugin linux-fontconfig-2.2.3_5 Linux/i386 binary of Fontconfig linux-glib2-2.6.6 Version 2.X Linux/i386 binary port of GLib linux-gtk2-2.6.10 GTK+ library, version 2.X, Linux binary linux-jpeg-6b.34RPM of the JPEG lib linux-openmotif-2.2.4_2 Motif toolkit Linux libraries linux-pango-1.8.1 Linux pango binary linux-png-1.2.8_2 RPM of the PNG lib linux-realplayer-10.0.7.785.20060201 Linux RealPlayer 10 from RealNetworks linux-tiff-3.7.1TIFF library, Linux/i386 binary linux-xorg-libs-6.8.2_5 Xorg libraries, linux binaries linux_base-fc-4_8 Base set of packages needed in Linux mode (for i386/amd64) linuxpluginwrapper-20051113_4 A wrapper allowing use of linux-plugins with native applica linuxthreads-2.2.3_21 POSIX pthreads implementation using rfork to generate kerne I am running 5.5 on this machine though. And linux compatibility is enabled I assume? Yeh!! I am just running xorg and not XFree86. Do you think I need to install XFree86? Also I installed acroread from the ports. Should not it fetch all the dependancies? Regarding linux compatibility: [EMAIL PROTECTED] ~]$ cat /etc/rc.conf | grep linux linux_enable=YES So, yes, its enabled. Thanks for replying back. Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Flash Plugin not working
Hello Michael, Thanks for the info. This is just for the help of others. The commands present there helped me and flash is currently working fine for me. Thanks Subhro On 10/16/06, Michael S [EMAIL PROTECTED] wrote: I followed the link below (just executed the commands, I can't read Portuguese) and everything worked fine. http://www.unixlike.com.br/?p=%2081 --- Subhro [EMAIL PROTECTED] wrote: Hello, I am running FreeBSD 6.2-PRERELEASE on i386 hardware. I have installed linux-firefox and linux-flashplugin from the ports collection. The same is iterated by pkg_info. [EMAIL PROTECTED] ~]$ pkg_info | grep flash linux-flashplugin-7.0r68 Adobe Flash Player NPAPI Plugin [EMAIL PROTECTED] ~]$ linux-firefox [EMAIL PROTECTED] ~]$ pkg_info | grep firefox firefox-1.5.0.7,1 Web browser based on the browser portion of Mozilla linux-firefox-1.5.0.7 Web browser based on the browser portion of Mozilla However when I am trying to open any sites from linux-firefox, the embedded flash applications are not displayed. Also the browser complains about missing plugin. I have checked the installed plugins by typing about:plugins. But there is no flash plugin displayed there either. Where am I going wrong? Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Acroread not working
Thanks for your reply Michael. Here is the output: phoenix# pkg_info | grep linux linux-atk-1.9.1 Accessibility Toolkit, Linux/i386 binary linux-expat-1.95.8 Linux/i386 binary port of Expat XML-parsing library linux-firefox-1.5.0.7 Web browser based on the browser portion of Mozilla linux-flashplugin-7.0r68 Adobe Flash Player NPAPI Plugin linux-glib2-2.6.6 Version 2.X Linux/i386 binary port of GLib linux-gtk-1.2.10_4 RPM of the Gtk lib linux-hicolor-icon-theme-0.5 A high-color icon theme shell from the FreeDesktop project linux-jpeg-6b.34RPM of the JPEG lib linux-png-1.2.8_2 RPM of the PNG lib linux-tiff-3.7.1TIFF library, Linux/i386 binary linux-xorg-libs-6.8.2_5 Xorg libraries, linux binaries linux_base-fc-4_9 Base set of packages needed in Linux mode (for i386/amd64) linuxpluginwrapper-20051113_6 A wrapper allowing use of linux-plugins with native applica Also I have installed acroread from ports. So sould it not fetch all the dependancies? Thanks Subhro On 10/16/06, Michael S [EMAIL PROTECTED] wrote: Have you enabled Linux emulation in your /etc/rc.conf ? Do you have the linux_base and related (linux_gtk, linux_XFree) ports installed? Have you also added linuxprocfs to your /etc/fstab file? --- Subhro [EMAIL PROTECTED] wrote: Hello Folks, I have installed acroread from the ports collection. I am running FreeBSD 6.2-PRERELEASE. When I am trying to run the same from the command line, I am getting quite a few errors. I have pasted the error below. [EMAIL PROTECTED] ~]$ acroread (acroread:6260): GdkPixbuf-WARNING **: Can not open pixbuf loader module file '/ etc/gtk-2.0/gdk-pixbuf.loaders': No such file or directory (acroread:6260): GdkPixbuf-WARNING **: Error loading XPM image loader: Image typ e 'xpm' is not supported (acroread:6260): GdkPixbuf-WARNING **: Can not open pixbuf loader module file '/ etc/gtk-2.0/gdk-pixbuf.loaders': No such file or directory (acroread:6260): GdkPixbuf-WARNING **: Error loading XPM image loader: Image typ e 'xpm' is not supported (acroread:6260): GdkPixbuf-WARNING **: Can not open pixbuf loader module file '/ etc/gtk-2.0/gdk-pixbuf.loaders': No such file or directory (acroread:6260): GdkPixbuf-WARNING **: Error loading XPM image loader: Image typ e 'xpm' is not supported (acroread:6260): GLib-GObject-CRITICAL **: g_object_ref: assertion `G_IS_OBJECT (object)' failed (acroread:6260): GLib-GObject-CRITICAL **: g_object_ref: assertion `G_IS_OBJECT (object)' failed (acroread:6260): GLib-GObject-CRITICAL **: g_object_ref: assertion `G_IS_OBJECT (object)' failed (acroread:6260): GLib-GObject-CRITICAL **: g_object_unref: assertion `G_IS_OBJEC T (object)' failed (acroread:6260): GLib-GObject-CRITICAL **: g_object_unref: assertion `G_IS_OBJEC T (object)' failed (acroread:6260): GLib-GObject-CRITICAL **: g_object_unref: assertion `G_IS_OBJEC T (object)' failed (acroread:6260): Gdk-CRITICAL **: file gdkwindow-x11.c: line 3502 (gdk_window_se t_icon_list): assertion `GDK_IS_PIXBUF (pixbuf)' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_ get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_ get_height): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_ get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_ get_height): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_ get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_ get_height): assertion `pixbuf != NULL' failed (acroread:6260): Gdk-CRITICAL **: file gdkwindow-x11.c: line 3502 (gdk_window_se t_icon_list): assertion `GDK_IS_PIXBUF (pixbuf)' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_ get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_ get_height): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_
Acroread not working
' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_ get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_ get_height): assertion `pixbuf != NULL' failed (acroread:6260): Gdk-CRITICAL **: file gdkwindow-x11.c: line 3502 (gdk_window_set_icon_list): assertion `GDK_IS_PIXBUF (pixbuf)' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_get_height): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_get_height): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 481 (gdk_pixbuf_get_width): assertion `pixbuf != NULL' failed (acroread:6260): GdkPixbuf-CRITICAL **: file gdk-pixbuf.c: line 497 (gdk_pixbuf_get_height): assertion `pixbuf != NULL' failed ** (acroread:6260): WARNING **: No builtin or dynamically loaded modules were found. Pango will not work correctly. This probably means there was an error in the creation of: '/etc/pango/pango.modules' You may be able to recreate this file by running pango-querymodules. (acroread:6260): GLib-GObject-CRITICAL **: g_object_ref: assertion `G_IS_OBJECT (object)' failed ** (acroread:6260): CRITICAL **: file pango-engine.c: line 68 (_pango_engine_shape_shape): assertion `PANGO_IS_FONT (font)' failed ** ERROR **: file shape.c: line 75 (pango_shape): assertion failed: (glyphs-num_glyphs 0) aborting... [EMAIL PROTECTED] ~]$ uname -a FreeBSD phoenix.ivizindia.com 6.2-PRERELEASE FreeBSD 6.2-PRERELEASE #0: Sat Oct 14 13:17:59 IST 2006 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/PHOENIX i386 Please tell me where I am going wrong. Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Flash Plugin not working
Hello, I am running FreeBSD 6.2-PRERELEASE on i386 hardware. I have installed linux-firefox and linux-flashplugin from the ports collection. The same is iterated by pkg_info. [EMAIL PROTECTED] ~]$ pkg_info | grep flash linux-flashplugin-7.0r68 Adobe Flash Player NPAPI Plugin [EMAIL PROTECTED] ~]$ linux-firefox [EMAIL PROTECTED] ~]$ pkg_info | grep firefox firefox-1.5.0.7,1 Web browser based on the browser portion of Mozilla linux-firefox-1.5.0.7 Web browser based on the browser portion of Mozilla However when I am trying to open any sites from linux-firefox, the embedded flash applications are not displayed. Also the browser complains about missing plugin. I have checked the installed plugins by typing about:plugins. But there is no flash plugin displayed there either. Where am I going wrong? Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: X Configuration Woes
On 9/12/06, Arindam [EMAIL PROTECTED] wrote: 1. The Mouse still does not work ... may be I should try MouseSystems protocol. You need to put the proper protocol in xorg.conf 2. What should I do about GNOME / KDE etc. I am not aching to get a jazzy a GUI on my FreeBSD installation. I can make do with a very minimal one. But I want a minimal one at least now, I just have to get this running or I can't sleep. Try ratpoison if you are more keyboard friendly or try out enlightenment if you are mouse friendly. Cheers!! Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
load balancing nat
Hello folks,
I have a strange problem on hand. I have got two internal LANs and one
ISP link. I am trying to share the link between the two internal LANs
and do a load balancing between the two. The rules I am using are:
nat on $ext_if from { $int1_if:network, $int2_if:network } to any -
$ext_if round-robin
where $int1_if, $int2_if are two internal interfaces and $ext_if is
the external interface.
However my observation is systems using $int_2 as gateway loose
connectivity randomly. Also the TTL values for the pings to the
gateway change to 150 from 64 as soon as the system looses
connectivity.
The systems in the LAN are all windows xp boxes.
Could anyone please tell me where I am going wrong?
Thanks and Best Regards
Subhro
--
Subhro Kar
Security Engineer
iViZ Techno Solutions Pvt. Ltd.
Dhanshree Bldg, 1st Floor
Plot XI-16, Sector V
Salt Lake City
700091
India
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: load balancing nat
Hello Bob,
Thanks for taking the time to answer. I would post a diagram as requested.
To ISP
| (ext_if)
--
| |
| FBSD |
||
(int1_if)| |(int2_if)
| |
- -
||
---
||| |
| LAN 1|| LAN 2 |
| || |
As shown above, int1_if = 192.168.0.0/24 and int2_if = 10.0.0.0/24
The FreeBSD box needs to route the packes from both the networks to
the ISP with equal priority.
Thanks and Best Regards
Subhro
On 9/5/06, Bob [EMAIL PROTECTED] wrote:
How about posting a diagram of the cable wiring of your network,
then maybe we have a starting point to work on your problem.
Chances this has nothing to do with NAT as source of problem.
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Subhro
Sent: Monday, September 04, 2006 5:04 PM
To: FreeBSD Questions
Subject: load balancing nat
Hello folks,
I have a strange problem on hand. I have got two internal LANs and one
ISP link. I am trying to share the link between the two internal LANs
and do a load balancing between the two. The rules I am using are:
nat on $ext_if from { $int1_if:network, $int2_if:network } to any -
$ext_if round-robin
where $int1_if, $int2_if are two internal interfaces and $ext_if is
the external interface.
However my observation is systems using $int_2 as gateway loose
connectivity randomly. Also the TTL values for the pings to the
gateway change to 150 from 64 as soon as the system looses
connectivity.
The systems in the LAN are all windows xp boxes.
Could anyone please tell me where I am going wrong?
Thanks and Best Regards
Subhro
--
Subhro Kar
Security Engineer
iViZ Techno Solutions Pvt. Ltd.
Dhanshree Bldg, 1st Floor
Plot XI-16, Sector V
Salt Lake City
700091
India
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
--
Subhro Kar
Security Engineer
iViZ Techno Solutions Pvt. Ltd.
Dhanshree Bldg, 1st Floor
Plot XI-16, Sector V
Salt Lake City
700091
India
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Newbie questions
Hello, Welcome to the world of FreeBSD. First of all, why are you trying to install binaries? I would say it is wiser to use the port system yourself. However remember to cvsup your ports tree before you start using it to get the required software. Refer to the handbook for understanding how ports work. Thanks and Best Regards Subhro On 8/23/06, E. Gad [EMAIL PROTECTED] wrote: Hello First I was directed to post the here because I posted to the stable mailing list before re-reading what it's purpose is- I apologise-. I am playing with freebsd 6 on a testing box. I Upgraded l from 6.0 to 6.1 because it looked like popular opinion is that it's got a number of improvements After a few false starts and finally figuring what I did wrong it went basicly ok. I went to use sysinstall to install a few usefull looking items however I got a error message: Release 6.1-p3 not found on server What is puzling is if I do essentially the samething: run pkg_add -f from the command line I seem to get some of the packages I wanted-to install. Is this normal? or did I do something wrong? I am not entirely sure how fix this and any assistance is apreciated. (The free-bsd etiquite note statements says I should mention what I have done so far) I have started by using google to see if anyone else has this problem. I haven't found the problem on bulitin boards or the like (not yet anyway-i'll look again in the morning) -thanks - Do you Yahoo!? Get on board. You're invited to try the new Yahoo! Mail. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Boot over network
Hello Folks, I was just wondering if this can be done. I would like to have a FreeBSD server which would supply a few workstations connected over the network a boot image. The catch is the boot image has to be a Ubuntu Linux image. I have a fresh installed FreeBSD box as well as a working Ubuntu box which boots locally. All the systems in question has network boot enabled NICs. Can the above setup be done? Any pointers would be welcome. Thanks and Best Regards Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: What FreeBSD users really want
Hello Sammy, It is really nice that you have told us yourt insight on the matter. I would also like to express my ideas. Please read my replies inline. On 7/22/06, sammy sumer [EMAIL PROTECTED] wrote: Every Linux Distributor in the world is hard at work reinventing the interface and making the Linux as user friendly as possible but we're still dogged by turn of the century hassle with our FreeBSD. This is not correct. The only distros which are working hard to get the interface more friendly are thoes which has some kind of earning. Just for example, if you check slackware, they still have a barebones interface. Secondly FreeBSD community only looks after the base tree. And as per my knowledge, the interface is something external. Here is what I would fix: 1.Reinvent the installer and interface. This is not a bad idea. But again is that really worth the trouble. The existing interface works perfectly. So why fix something which is not broken. BTW, by reinventing if you mean to say that make the installer go graphical, then there is a small problem. You are making the installer more heavy which really has no value. 2.Integrate a PHP shell into the core of the system. This would be a very good idea if you have something call FreeBSD-Web_Edition which is not the case. FreeBSD hosts all kinds of services. Therefore the more things u put in stock OS, there would be more points of failure. BTW why do you feel that the existing port system is not adequate? PHP is by far the most popular computing language in the world. Why not have a shell called PHP shell. So lots of web developers out there can easily create shell scripts in PHP syntax to automate and run programs on FreeBSD. Perl is no less popular. Specially Perl had been around far longer than PHP. But FBSD does not have perl in stock installations either. Primarrily for the idea of Keep It Simple. Who wants to learn bash or sh scripting? They are by far the least popular and ugly programming language in the world. It may be ugly, but its a really fast way to implement small operations. And FYI, we system admins swear by shell scripts. It is astounding that FreeBSD developers have not clued in to the fact that millions of backend webmasters could easily migrate and adopt FreeBSD as their O.S of their choice because of PHP. Do you have this documented? 3.Content Management Website Your current website looks very ordinary and doesn't make any impression for anyone visiting your site for the first time. Well we recently got the website look changed. Did you like the earlier view? Would you please tell us what you mean by ordinary and what kind of website would be more acceptable to people in generaly. Please consider the fact that sometimes all you have is a text based browser to refer to the handbook when you are stuck up in the middle of an installation. So please provide your comments considering the same. Don't get me wrong, I love FreeBSD and I always remain loyal to it. I love the unique port collection concept for third party application installation. Of course not. The biggest asset of FreeBSD is its users. So as a user you have full rights to express your insight. Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Problem in Starting KDE
Let me have a look at /etc/make.conf and /etc/resolv.conf Subhro On 7/18/06, Sean M. [EMAIL PROTECTED] wrote: OK, that one little thing has made it about 80% perfect now. Just three details: 1) It takes an awfully long time to start up. I guess this is related to the next point: 2) The output from 'startx' is still mostly the same as before: xauth: creating new authority file /root/.serverauth.566 ### Standard X startup message ### DCOPClient::attachInternal. Attach failed Could not open network socket DCOPClient::attachInternal. Attach failed Could not open network socket Warning: kbuildsycoca is unable to register with DCOP. kbuildsycoca running... DCOPClient::attachInternal. Attach failed Could not open network socket kbuildsycoca running... DCOP Cleaning up dead connections. Reusing existing ksycoca ### Still a pagefull of kbuildsyscoa mime-type warnings ### 3) In the course of using Konqueror, I see kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol PKCS7_content_free kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OpenSSL_add_all_algorithms kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OPENSSL_add_all_algorithms kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OpenSSL_add_all_algorithms_conf kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol PKCS7_content_free kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OpenSSL_add_all_algorithms kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OPENSSL_add_all_algorithms kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OpenSSL_add_all_algorithms_conf kio (KLauncher): ERROR: SlavePool: No communication with slave. kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol PKCS7_content_free kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OpenSSL_add_all_algorithms kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OPENSSL_add_all_algorithms kdecore (KLibLoader): WARNING: KLibrary: Undefined symbol OpenSSL_add_all_algorithms_conf kio (KIOConnection): ERROR: Could not write data kio (KIOConnection): ERROR: Could not write data kio (KIOConnection): ERROR: Could not write data get written. --- Subhro [EMAIL PROTECTED] wrote: Add this so that the hosts looks like this: On 7/18/06, Sean M. [EMAIL PROTECTED] wrote: Here is /etc/hosts. It's not very spectacular. # # This file should contain the addresses and aliases for local hosts that # share this file. Replace 'my.domain' below with the domainname of your # machine. # # In the presence of the domain name service or NIS, this file may # not be consulted at all; see /etc/nsswitch.conf for the resolution order. # # ::1 localhost localhost.my.domain 127.0.0.1 localhost localhost.my.domain 127.0.0.1 compy compy.my.domain # # Imaginary network. #10.0.0.2 myname.my.domain myname #10.0.0.3 myfriend.my.domain myfriend # # According to RFC 1918, you can use the following IP networks for # private nets which will never be connected to the Internet: # # 10.0.0.0- 10.255.255.255 # 172.16.0.0 - 172.31.255.255 # 192.168.0.0 - 192.168.255.255 # # In case you want to be able to connect to the Internet, you need # real official assigned numbers. Do not try to invent your own network # numbers but instead get one from your network provider (if any) or # from your regional registry (ARIN, APNIC, LACNIC, RIPE NCC, or AfriNIC.) # o.com Your issue is, X does not know how to connect to compy:0. Creating an entry in the hosts tells it the IP to connect. :-) Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: problems running freebsd 6.0+
Tom Cruickshank wrote: Hello, Hello Tom, I'm hoping is the correct mailing list for this, if not, please feel free to direct me to a more appriopriate one. You are on the correct mailing list :-). I have a box which I'm trying to run FreeBSD on. I can run FreeBSD 5.4 on it without any problems, but if I try run FreeBSD 6.0 or 6.1, at any point in time while the system is running (could be on load up or when system is already loaded), the computer just *freezes*. The only thing which can be done afterwards is a cold reboot. I hav checked the /var/log/messages file and haven't been able to find anything wrong. Hardware specs: Motherboard: A7N8X-X The information you have provided is not complete. We would be requiring more information to understand what is going wrong. For a start can you show us a copy of dmesg and your kernel config file (if you are not running a GENERIC kernel). Thanks and Best Regards Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Content filtering
Loren M. Lang wrote: Shawn Guillemette wrote: Hello, I have recently been thinking about adding content filtering to my FreeBSD fire wall at home as the kids are starting to use the internet more and they are getting older too ;-) I'm running FreeBSD 4.11 RELEASE using IPFW as my firewall. The system its running on is an old alpha machine. I was wondering if anyone knew of a port that I could use to filter some web content from my children. I do have the X86 option as well Just have to reload the OS and start from scratch on another system. Thanks Shawn ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] I'd look at squid+squidguard. Both are opensource and available in ports. How about dansguardian. Also set up a transparent proxy set up so that the kids cant get past the proxy settings :-D Thanks and Best Regards Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Openoffice compilation failure
On 6/1/06, Lowell Gilbert [EMAIL PROTECTED] wrote: Andrea Venturoli [EMAIL PROTECTED] writes: I reported it several months ago and all I got to be told was that it's a strange problem. Well, that's true... Do you have devel/epm installed by any chance? No I do not have epm installed. Should I install it and try again? Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Openoffice compilation failure
On 6/2/06, Lowell Gilbert [EMAIL PROTECTED] wrote: Subhro [EMAIL PROTECTED] writes: On 6/1/06, Lowell Gilbert [EMAIL PROTECTED] wrote: Andrea Venturoli [EMAIL PROTECTED] writes: I reported it several months ago and all I got to be told was that it's a strange problem. Well, that's true... Do you have devel/epm installed by any chance? No I do not have epm installed. Should I install it and try again? No. If you had it, I would recommend removing it before trying again. Initially did not have epm. Even tried to compile *with* epm installed. Still stuck up at the same place. :-( Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Openoffice compilation failure
Hello folks, I am running FreeBSD-6.1-STABLE. I was trying to compile OpenOffice 2.0 from the ports tree. Below I have mentioned the error I am getting. Can anyone please tell me whats wrong? ... cleaning the output tree ... ... removing directory /usr/ports/editors/openoffice.org-2.0/work/OOB680_m5/inst setoo_native/unxfbsd.pro/OpenOffice/bsd/zip/en-US ... ... removing directory /usr/ports/editors/openoffice.org-2.0/work/OOB680_m5/inst setoo_native/unxfbsd.pro/OpenOffice/bsd/services.rdb/en-US ... ... removing directory /usr/ports/editors/openoffice.org-2.0/work/OOB680_m5/inst setoo_native/unxfbsd.pro/OpenOffice/bsd/starregistryrdb/en-US ... ... removing directory /usr/ports/editors/openoffice.org-2.0/work/OOB680_m5/inst setoo_native/unxfbsd.pro/OpenOffice/bsd/stripped/en-US ... ** ERROR: ERROR: epm -f bsd openoffice.org-gnome-integration /usr/ports/editors/op enoffice.org-2.0/work/OOB680_m5/instsetoo_native/unxfbsd.pro/OpenOffice/bsd/list file/en-US/epm_OpenOffice_gid_Module_Optional_Gnome_unxfbsd_OOB680__en-US.lst -v 21 |! in function: call_epm ** ** ERROR: Saved logfile: /usr/ports/editors/openoffice.org-2.0/work/OOB680_m5/insts etoo_native/unxfbsd.pro/OpenOffice/bsd/logging/en-US/log_OOB680__en-US.log ** Mon May 29 11:22:37 2006 (01:10 min.) dmake: Error code 255, while making 'openoffice_en-US.bsd' '---* tg_merge.mk *---' ERROR: Error 65280 occurred while making /usr/ports/editors/openoffice.org-2.0/w ork/OOB680_m5/instsetoo_native/util dmake: Error code 1, while making 'build_instsetoo_native' '---* *---' *** Error code 255 Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Software taking a long time to load on FreeBSD6
Levi Campbell sat at his 'puter and typed on 5/20/2006 8:51: Why is it that some applications like x11, ratpoison, and firefox come up instantly while applications like xmms, emacs and thunderbird take about five minutes to load? I've tried several things to try and fix this. - I've deinstalled packages to see if ports was any better and vice versa. - I've cleaned out /tmp, /var/tmp, and /var/lock and checked free space. - getting the vanilla sources from the origional FTP site and compiling them Does the hostname for your system resolve? If not, either set it up or put proper entries in /etc/hosts Thanks and Best Regards Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Error in installing c++ API
how are you trying to make ir? You can try gmake once. Subhro On 5/16/06, [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: Please send me the process to install the c++ API,as i am facing problem when typing make install is given .The error is makefile:68*** missing separator stop, all client libraries are loaded. mail2web - Check your email from the web at http://mail2web.com/ . ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Sluggish system
You can do a pkg_delete -a. This will delete all the packages. After that pkgdb -fF This will rebuild the package database. However I dont think this is necessary. then reinstall everything as required. Thanks and Best Regards Subhro On 5/16/06, [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: Quoting Subhro [EMAIL PROTECTED]: Why do you want to NOT reinstall the OS? Loads of data, loads of accounts / passwords, nothing wrong with the 'base' part of the OS... There's no need to really. My problems are generated from to many ports / inconsistencies in the ports, and so forth. So that's really the only part of the OS that actually needs some serious work. I also can't re-install the Base OS remotely... Yes, I can make world to upgrade it (which has already been done), but not reinstall it in the sense of format / repartition / etc... -- Chris ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. Dhanshree Bldg, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Bluetooth not working
Hello Folks, Recently I bought a new bluetooth dongle, an ISSC Bluetooth Stack implementation. It works (apparently seems so) with Wind0ze. But when I plug it into my FreeBSD 6.1-STABLE box, I get this in the kernel logs: May 9 15:43:32 phoenix kernel: ubt0: vendor 0x1131 ISSCBTA, rev 1.10/3.73, addr 2 May 9 15:43:32 phoenix kernel: ubt0: vendor 0x1131 ISSCBTA, rev 1.10/3.73, addr 2 May 9 15:43:32 phoenix kernel: ubt0: Interface 0 endpoints: interrupt=0x81, bulk-in=0x82, bulk-out=0x2 May 9 15:43:32 phoenix kernel: ubt0: Interface 1 (alt.config 5) endpoints: isoc-in=0x83, isoc-out=0x3; wMaxPacketSize=49; nframes=6, buffer size=294 May 9 15:43:37 phoenix kernel: ng_hci_process_command_timeout: ubt0hci - unable to complete HCI command OGF=0x3, OCF=0x3. Timeout May 9 15:43:38 phoenix root: /etc/rc.d/bluetooth: ERROR: Unable to setup Bluetooth stack for device ubt0 What could be the problem? Any insights? Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Upgrade 5.4 - 6.0 errors.
On 5/9/06, Ben Hacker Jr [EMAIL PROTECTED] wrote: Is there a way to clean out my /usr/src directory and start from scratch in case it is corrupted some how?? rm -rf /usr/src/* snip $ su root -c make kernel KERNCONF=HACK06 The correct command is make buildkernel KERNCONF=HACK06 and not make kernel You need to read the handbook :-) snip Manually attempting to build my kernel will yield the following: hackserver$ su root Password: hackserver# pwd /usr/src/sys/i386/conf hackserver# config HACK06 ERROR: version of config(8) does not match kernel! config version = 500013, version required = 63 This is a deprecated method. Not a good idea to try out. :-) Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: jails or chroot?
On 5/9/06, Michael Grant [EMAIL PROTECTED] wrote: I host a bunch of websites on my box. Recently I had some problems with file access problems with php which caused me to look into putting each of my clients into their own jail or chroot. I have roughly 100 different domains I'd need to split. I won't be doing this even if someone pays me twice for doing it. This is going to create a HELL lot of problems later on, especially during upgrades. BTW can you tell us your exact requirements? Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Remote 'viewing / control' of X Windows
Marc G. Fournier sat at his 'puter and typed on 5/7/2006 7:02: I'm dealing with a situation where I'm migrating ppl over to using X vs M$ Windows ... I'd like to be able to help them out remotely, similar to how I can with VNC for Windows ... Is there something similar for Unix that would allow me to 'piggyback' in such a way that they're X desktop is an xterm on my machine, so that I can move their mouse around, show them the steps to do something, etc? VNC had also been ported to FreeBSD. You can try something like tightvnc. Thanks and Best Regards Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: problem building xorg
Did you cvsup before building? If not then please do so. Also please post the output of gnomelogalyzer Subhro On 3/28/06, RJ45 [EMAIL PROTECTED] wrote: I am doing it on a new installation with no previous port installed I do not know why it behaves liek that ... any hints ? thanks Rick On Tue, 28 Mar 2006, Subhro wrote: Hello, checking for xrender = 0.8.2... gnome-config: not found gnome-config: not found checking for xrender = 0... gnome-config: not found gnome-config: not found checking for X... libraries /usr/X11R6/lib, headers /usr/X11R6/include checking X11/extensions/Xrender.h usability... no checking X11/extensions/Xrender.h presence... no checking for X11/extensions/Xrender.h... no configure: error: Xrender.h not found. === Script configure failed unexpectedly. Please run the gnomelogalyzer, available from http://www.freebsd.org/gnome/gnomelogalyzer.sh;, which will diagnose the problem and suggest a solution. If - and only if - the gnomelogalyzer cannot solve the problem, report the build failure to the FreeBSD GNOME team at [EMAIL PROTECTED], and attach (a) Whats the output of that script? Are u installing xorg on a freshly installed system or did this contain something earlier? Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: problem building xorg
Please answer the questions I have asked you. You are constantly posting new errors without performing any diagnostic steps that had been provided. Without that, it is very difficult to help you out. Subhro On 3/29/06, RJ45 [EMAIL PROTECTED] wrote: cc -O2 -fno-strict-aliasing -pipe -mcpu=ev4 -mtune=ev5 -mieee -mcpu=ev4 -mtune=ev5 -mieee -I/usr/X11R6/include-DCSRG_BASED -DFUNCPROTO=15 -DNARROWPROTO -c fvwm.c In file included from fvwm.c:45: fvwm.h:40:22: X11/Xlib.h: No such file or directory fvwm.h:41:23: X11/Xutil.h: No such file or directory fvwm.h:42:28: X11/cursorfont.h: No such file or directory fvwm.h:57:27: X11/Intrinsic.h: No such file or directory In file included from fvwm.c:45: I am not able to compile anything related to X11, where I can find pre compiled package of X11 for FreeBSD alpha ? I ahve 6.1-PRERELEASE on alpha built form ports I have no existent X11 include files... any hints please ? thanks Rick On Wed, 29 Mar 2006, Subhro wrote: Did you cvsup before building? If not then please do so. Also please post the output of gnomelogalyzer Subhro On 3/28/06, RJ45 [EMAIL PROTECTED] wrote: I am doing it on a new installation with no previous port installed I do not know why it behaves liek that ... any hints ? thanks Rick On Tue, 28 Mar 2006, Subhro wrote: Hello, checking for xrender = 0.8.2... gnome-config: not found gnome-config: not found checking for xrender = 0... gnome-config: not found gnome-config: not found checking for X... libraries /usr/X11R6/lib, headers /usr/X11R6/include checking X11/extensions/Xrender.h usability... no checking X11/extensions/Xrender.h presence... no checking for X11/extensions/Xrender.h... no configure: error: Xrender.h not found. === Script configure failed unexpectedly. Please run the gnomelogalyzer, available from http://www.freebsd.org/gnome/gnomelogalyzer.sh;, which will diagnose the problem and suggest a solution. If - and only if - the gnomelogalyzer cannot solve the problem, report the build failure to the FreeBSD GNOME team at [EMAIL PROTECTED], and attach (a) Whats the output of that script? Are u installing xorg on a freshly installed system or did this contain something earlier? Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Mozilla Crashing
Hello, Recently I upgraded to flashplugin 7 from flashplugin6. Eversince when I try to open a webpage with flash, I get the following error and mozilla automatically closes. /libexec/ld-elf.so.1: /usr/local/lib/pluginwrapper/flash7.so: Undefined symbol _dlsym What could be the problem? I am using the latest verson of port tree and FreeBSD 6.1-PRERELEASE. Thanks and Best Regards Subhro -- Subhro Kar Security Engineer iViZ Techno Solutions Pvt. Ltd. eRevMax House, 1st Floor Plot XI-16, Sector V Salt Lake City 700091 India ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
VPN not working
packet to 220.225.82.250 my_port 500 peer_port 500 (I) MM_NO_STATE *Feb 3 22:01:28.147: %SYS-2-CHUNKBADMAGIC: Bad magic number in chunk header, chunk 0 data 446BFA58 chunkmagic 400B97A8 chunk_freemagic 43EDF2FC -Process= IP Input, ipl= 4, pid= 74 -Traceback= 0x40ABDEE8 0x400BC510 0x402FF6B4 0x40ED1738 0x40ED48EC 0x40ED2F8C 0x40ED325C 0x40ED3318 0x40ED34BC - I am using the method mentioned in the freebsd handbook. Please help me out by telling me what exactly is wrong. Thanks and Best Regards Subhro ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Freebsd Theme Song
Kevin Kinsey sat at his 'puter and typed on 12/11/2005 11:04: Hope this saves somebody a few keystrokes: * VI * #!/bin/sh # themesong ... enables you to quickly create a singable # ode to your favorite FreeBSD pet peeve. Add it, along with # mail(1) to your crontab to really annoy list members. # # License: BSD, of course. Additions welcome, provided # the meet with the goals of the Project. if [ $OSTYPE != FreeBSD ]; then echo Wrong O.S. --- Gritch on your own project/distro's list! exit 1 fi case $1 in -c) cat /COPYRIGHT exit 0;; -C) cat /COPYRIGHT exit 0;; # let the GNU people gritch too; but they won't like this part --copyright) cat /COPYRIGHT exit 0;; esac if [ $1 ]; then echo THE BIKESHED SONG sung to 'You are my Sunshine' and humbly submitted as a candidate in the soon-to-be-announced FreeBSD Theme Song Contest (but definitely not in any code competitions...) '$1' is my bikeshed, my only bikeshed '$1' makes me happy to gritch and moan; You'll never know, friend, how much I loathe '$1' Won't you please leave my '$1' alone!? else echo Usage: themesong foo ---where 'foo' is a description of your pet peeve with this O.S., e.g. 'themesong networking' fi * DE * :D Kevin Kinsey ROFLMAO This is definitely the best of all. Well done Kevin. Simply marvelous Thanks S. -- --- \ / | Subhro Sankha Kar \./ | GSM: +919831010002 -- Fax: +919831832913 (0Y0) |MSN: [EMAIL PROTECTED] -- Yahoo!: subhro82 -ooO--(_)--Ooo- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Unable to start Webmin
Gerard Seibert sat at his 'puter and typed on 12/8/2005 0:51: Webmin has suddenly refused to start. This is the message displayed: Starting webmin. Segmentation fault (core dumped) A humongous 'perl.core' file is produced. I tried removing and reinstalling webmin, but that failed to alleviate the problem. I am open to any suggestions. Seems as if perl is messed up. Can you report back perl -v. Better still, try to reinstall perl if possible. Regards S. -- --- \ / | Subhro Sankha Kar \./ | GSM: +919831010002 -- Fax: +919831832913 (0Y0) |MSN: [EMAIL PROTECTED] -- Yahoo!: subhro82 -ooO--(_)--Ooo- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: The question that wont die: What size partitions should I make?
wrangled sat at his 'puter and typed on 12/5/2005 0:10: I have dual-boot laptop, 30GB Fat32 Win2000 and 70GB FreeBSD 6.0-R. I plan to use this for normal home desktop use (not as a server). I have 512MB RAM. According to this page: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/install-steps.html I should use: / = 100MB /swap = 1GB /var = 50MB /usr = rest (68GB) On past FreeBSD installs, I would occasionaly do things as root, and ran out of space in /root. Since then, on desktop machines (with 250GB drives), I would make / be 4GB. On my lapatop, I wouldn't want to give up 4 of my 70 gigs if I didn't have to. So I am looking for a realistic number that wont cramp me, and wont waste too much space. I am planning on 1GB, so it will be big enough to hold the contents of a 700MB CD ISO. That is a VERY VERY BAD idea. It is not recommended to do ANYTHING as root which can be done as some other non privileged user. I have no idea how much of /var I need, other than I like to install various packages to try them out, and I would not want to limit something like a webserver or email server if I chose to run one for limited use. A friend took the default install suggestions for a machine he planned to do some web development on, and said his /var was way too small (they were new to FreeBSD also). I am guessing 5GB for /var would allow me to run a mail-server (for personal use) and Apache+extensions for limited website developement Generally the maximum space is eaten up by the logs and the databases (if any) hosted on the system. A swap of 1GB is fine, I'm not sure I've ever actually used any swap on my machines that had more than 128MB. Depends solely on the applications you are trying to run on the box. I want /usr to be as big as possible (obviously), so my primary user account will have as much space as possible in /use/home/account. Should I use: / = 1GB /swap = 1GB /var = 5GB /usr = rest (63GB) This is my personal scheme for my desktop which hosts my personal website and a very very small database which is basically my phone directory and appointment schedules. / = 128M swap=2G /var = 2G /var/tmp = 128M /usr = rest. /tmp is symlinked to /var/tmp. Now my system specs: Athlon 64Fx-55 1G DDR 400M RAM 3*160G SATA150 Western Digital in RAID 5 ASUS K8N-SLI DX motherboard. Again, nothing is absolute. Your requirement would dictate your labeling scheme. Thanks S. -- --- \ / | Subhro Sankha Kar \./ | GSM: +919831010002 -- Fax: +919831832913 (0Y0) |MSN: [EMAIL PROTECTED] -- Yahoo!: subhro82 -ooO--(_)--Ooo- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: doubts
Anirban Adhikary sat at his 'puter and typed on 11/30/2005 14:38: Hi guys this is Anirban.I have a doubt on the following write a Shell script that will take a tar backup of a user on a daily basis. Server details - 192.168.1.19 login - beta password - bta321 working directory to use anirban Hope i will receive my answer soon. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] Hello Anirban, What exactly do you want? You want a shell script to take tar backups of all the user directories or that of a particular user? I also do not understand why you are providing login information to your system. Thirdly that IP is a non routable IP address and is not accessible from outside. So that is of no use. Thanks S. -- --- \ / | Subhro Sankha Kar \./ | GSM: +919831010002 -- Fax: +919831832913 (0Y0) |MSN: [EMAIL PROTECTED] -- Yahoo!: subhro82 -ooO--(_)--Ooo- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Can't compile kernel
Jose Borquez sat at his 'puter and typed on 11/23/2005 12:50: I made a standard install of FreeBSD 5.4 with Kern-Developer Full binaries and doc, kernel source only. I attempted to compile a custom kernel running: make buildkernel KERNCONF=CUSTOM Then I get the following error: make: don't know how to make buildkernel. Stop I run it from the /usr/src/ directory. The /usr/src/ directory is empty. Does that mean the source files were not installed? Exactly. The kernel sources had not been installed. Read the chapter on building a custom kernel in the handbook. make sure you cvsup properly before you attempt to go for the compile. Regards S. -- --- \ / | Subhro Sankha Kar \./ | GSM: +919831010002 -- Fax: +919831832913 (0Y0) |MSN: [EMAIL PROTECTED] -- Yahoo!: subhro82 -ooO--(_)--Ooo- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Low volume
manish jain sat at his 'puter and typed on 11/8/2005 12:28: Hi, I am using FreeBSD 5.4 with an Intel 810 chipset which has an onboard soundcard. While everything else works fine, the sound volume is inexplicably low. I have set snd_ich_load to YES in loader.conf, which is probably all I am required to do. Even when I use Volume Control to set the PCM to maximum volume (with the 800 W speakers too set to maximum volume), sound is barely audible in multimedia applications like xmms and xine. What could possibly be wrong ? Thanks for any help. Manish Jain - Yahoo! FareChase - Search multiple travel sites in one click. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] Install aumix from the Ports collection and try to control the volume from there. Thanks S. -- ---+-- | Subhro Sankha Kar \ / | GSM: +919831064613 -- Fax: +919831832913 \./ | MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) | ICQ: 203567534 -- AIM: bsdboy1982 ooO--(_)--Ooo--+-- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: What happened with portaudit?
Kövesdán Gábor sat at his 'puter and typed on 11/6/2005 22:00: Hello, One of my machines I got a report about 3 vulnerable packages (php4, ruby, openssl) in tomorrows security run output, but in today's security run output all of them disappeared, but nobody upgraded or removed the affected packages. I reinstalled portaudit, refreshd its database, but now it reports 0 affected pakages. The pkg_info command lists that three packages, so they are still installed. Does anybody suspect what's wrong? Cheers, Gabor Kovesdan ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] The first thing I would do is check the tripwire checksums. Thanks S. -- ---+-- | Subhro Sankha Kar \ / | GSM: +919831064613 -- Fax: +919831832913 \./ | MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) | ICQ: 203567534 -- AIM: bsdboy1982 ooO--(_)--Ooo--+-- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Bug ?: SCHED_4BSD VS SCHED_ULE
Ian Lord sat at his 'puter and typed on 11/4/2005 9:28: Hi, I am running amd64 version on a Dell 2850 Dual Xeon processor with emt64 as soon as I turn on SCHED_ULE instead of SCHED_4BSD in rc.conf, the system starts to behave strangely. During boot, named and sshd can't start normally, system is unstable, etc What exactly is the problem? What kind of instability is noticed? Thanks S. -- ---+-- | Subhro Sankha Kar \ / | GSM: +919831064613 -- Fax: +919831832913 \./ | MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) | ICQ: 203567534 -- AIM: bsdboy1982 ooO--(_)--Ooo--+-- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Compile Kernel Question
Lonnie Cumberland sat at his 'puter and typed on 11/1/2005 3:05: Greetings All, I am new to FreeBSD but have a lot of Linux experience so I think that the migration should not be too difficult. The reason that I am investigating FreeBSD is because I hear that it performs GREAT under heavy loads and many larger ISP are using it without fail. In my experience, Linux, although a great OS, seems to bog down under heavy loading. I could be wrong though and it could have just been to misconfiguration on my part. Well, I have a base installation of FreeBSD 4.11 which is needed for a particular project but now need to compile the kernel to support QUOTA's. My question is how do I install the sources over the web so that I can compile the kernel to support quotas? The FreeBSD docs tell a little, but mostly assume that you have the sources already on the system to compile which I do not have and need to download them. If some one could please give me a little guidance then I would greatly appreciate it. Thanks in advance, Lonnie ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] Did you have a look at the handbook? Read through the chapter which describes about building your own kernel and world. http://www.freebsd.org/handbook/ Thanks S. -- ---+-- | Subhro Sankha Kar \ / | GSM: +919831064613 -- Fax: +919831832913 \./ | MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) | ICQ: 203567534 -- AIM: bsdboy1982 ooO--(_)--Ooo--+-- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: music on FreeBSD
Escape Velocity sat at his 'puter and typed on 10/4/2005 19:47: Yes, I understand it would be free and I am willing to abide by the BSD License - this song would be released under the Creative Commons license (http://creativecommons.org/licenses/by-nc-sa/2.5/). Let me know what I should do next. ]That's great. However I feel there is a small glitch. As per http://creativecommons.org/licenses/by-nc-sa/2.5/, the work can not be used for Commercial Purposses. However as per the BSD license you CAN use BSD License protected softwares for commercial purposes but you wont be allowed to call it a BSD Protected software any more. Thanks S. -- ---+-- | Subhro Sankha Kar \ / | GSM: +919831064613 -- Fax: +919831832913 \./ | MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) | ICQ: 203567534 -- AIM: bsdboy1982 ooO--(_)--Ooo--+-- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: How do you patch a driver?
Foo Ji-Haw sat at his 'puter and typed on 10/3/2005 10:03: Hello Subhro, Thanks for your help. From the link I have the following files: ata-mk3m.diff-current.gz (2k) ata-mk3m.diff-releng5.gz (2k) ata-mk3m.tar.gz (100k) ata-mk3n-releng5.tar.gz (113k) ata-mk3n.diff-releng5.gz (2k) Which file should I be using? Is 'current' better than 'releng5'? Do I also need to download a pair of files: ata-mk3m.diff-current.gz with ata-mk3m.tar.gz? Sorry, but I am quite confused with kernal patching. Recompiling yes, but never patched in my life. - Original Message - From: Subhro [EMAIL PROTECTED] To: Foo Ji-Haw [EMAIL PROTECTED] Cc: freebsd-questions@freebsd.org Sent: Monday, October 03, 2005 11:53 AM Subject: Re: How do you patch a driver? Foo Ji-Haw sat at his 'puter and typed on 10/3/2005 8:46: Hello Gheorghe, I read with interest your success in getting your Adaptec 1210SA to work on FreeBSD. In your email you wrote that you downloaded patches to the driver code (and recompiled the kernel?) from http://people.freebsd.org/~sos/ATA I downloaded the files myself, but am not sure how to proceed from there. Can you please give me some pointers on the next steps? Appreciate your help, thanks! ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] The general way to patch a driver is patch -p0 patch_file. The patch file is to be copied in the first level directory of the source code. Thanks S. You need to read the handbook. Read through the chapter describing the different trees of development. If you want to run the OS on a production box I would recommend stable. Current is only for developers. BTW, your mail client indents the replies incorrectly. I can see that you are using Microsoft Outlook 6.0. I would recommend get Thunderbird. It's a much better client alltogether. Thanks S. -- -+- | Subhro Sankha Kar \ / |GSM: +919831064613 -- Fax: +919831832913 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: music on FreeBSD
Escape Velocity sat at his 'puter and typed on 10/4/2005 8:57: Hello, my name is Michael Chagnon. I am in an independent music group called Escape Velocity. Our web site is located at: www.escapevelocity.comhttp://www.escapevelocity.com. I was interested in having one song of ours, from our new album, distributed with the FreeBSD package. So that when users install FreeBSD, they have a piece of music to test their new OS's audio with. Similar to when Windows 95 and 98 discs came with several videos and/or pieces of music. Please let me know who I must contact or what I should do to make this happen. If you need any information, please let me know. Thanks. --Michael ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] Hello Michael, Are you willing to give it out for free? Also are you willing to abide by the rules and reguulations of the BSD License? Thanks S. -- -+- | Subhro Sankha Kar \ / |GSM: +919831064613 -- Fax: +919831832913 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: How do you patch a driver?
Foo Ji-Haw sat at his 'puter and typed on 10/3/2005 8:46: Hello Gheorghe, I read with interest your success in getting your Adaptec 1210SA to work on FreeBSD. In your email you wrote that you downloaded patches to the driver code (and recompiled the kernel?) from http://people.freebsd.org/~sos/ATA I downloaded the files myself, but am not sure how to proceed from there. Can you please give me some pointers on the next steps? Appreciate your help, thanks! ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] The general way to patch a driver is patch -p0 patch_file. The patch file is to be copied in the first level directory of the source code. Thanks S. -- -+- | Subhro Sankha Kar \ / |GSM: +919831064613 -- Fax: +919831832913 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Help with Xorg
Hello folks, I am facing a problem in using the nvidia driver with Xorg. I have installed both the versions from the ports tree. When I start X with the nvidia driver, it complains that no GPU was found and subsequently it says that no usable Screens found. I am attaching the Xorg log file, the error which is thrown out while starting X and my xorg.conf. Help is greatly appreciated. Thanks and Best Regards S. -- Subhro Sankha Kar School of Information Technology Block AQ-13/1 Sector V ZIP 700091 India Xorg.0.log Description: Binary data error.log Description: Binary data xorg.conf Description: Binary data ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Help with Xorg
nawcom wrote: Is the nvidia module being loaded into the kernel? i am assuming so. the devices should be created during bootup. let me know if /dev/nvidia* is being created, or email a boot log. Thanks, Ben Hello Ben, Thanks for your reply. kldstat shows that nvidia.ko has been loaded. /dev/nvidia0 and /dev/nvidiactl is also present I am also attaching a boot lon. Please let me know if any more information is required. Thanks S. Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.4-STABLE #0: Mon Jun 6 07:33:01 IST 2005 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/FIREBOX Timecounter i8254 frequency 1193182 Hz quality 0 CPU: Intel Pentium III (994.46-MHz 686-class CPU) Origin = GenuineIntel Id = 0x68a Stepping = 10 Features=0x383f9ffFPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE real memory = 536870912 (512 MB) avail memory = 515612672 (491 MB) acpi0: PTLTD RSDT on motherboard acpi0: Power Button (fixed) Timecounter ACPI-fast frequency 3579545 Hz quality 1000 acpi_timer0: 24-bit timer at 3.579545MHz port 0xf008-0xf00b on acpi0 cpu0: ACPI CPU on acpi0 acpi_button0: Power Button on acpi0 pcib0: ACPI Host-PCI bridge port 0xcf8-0xcff on acpi0 pci0: ACPI PCI bus on pcib0 pcib1: ACPI PCI-PCI bridge at device 1.0 on pci0 pci1: ACPI PCI bus on pcib1 nvidia0: GeForce FX 5700LE mem 0xe000-0xefff,0xd000-0xd0ff irq 11 at device 0.0 on pci1 pcib2: ACPI PCI-PCI bridge at device 30.0 on pci0 pci2: ACPI PCI bus on pcib2 ohci0: OPTi 82C861 (FireLink) USB controller mem 0xd100-0xd1000fff irq 5 at device 11.0 on pci2 usb0: OHCI version 1.0, legacy support usb0: OPTi 82C861 (FireLink) USB controller on ohci0 usb0: USB revision 1.0 uhub0: OPTi OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered rl0: RealTek 8139 10/100BaseTX port 0x2000-0x20ff mem 0xd1001000-0xd10010ff irq 11 at device 13.0 on pci2 miibus0: MII bus on rl0 rlphy0: RealTek internal media interface on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: Ethernet address: 00:0b:2b:0d:fa:7c pcm0: Creative EMU10K1 port 0x2400-0x241f irq 5 at device 15.0 on pci2 pcm0: SigmaTel STAC9708/11 AC97 Codec isab0: PCI-ISA bridge at device 31.0 on pci0 isa0: ISA bus on isab0 atapci0: Intel ICH UDMA66 controller port 0x1800-0x180f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 uhci0: Intel 82801AA (ICH) USB controller port 0x1000-0x101f irq 5 at device 31.2 on pci0 usb1: Intel 82801AA (ICH) USB controller on uhci0 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: serial bus, SMBus at device 31.3 (no driver attached) atkbdc0: Keyboard controller (i8042) port 0x64,0x60 irq 1 on acpi0 atkbd0: AT Keyboard irq 1 on atkbdc0 kbd0 at atkbd0 psm0: PS/2 Mouse irq 12 on atkbdc0 psm0: model IntelliMouse Explorer, device ID 4 fdc0: floppy drive controller port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fd0: 1440-KB 3.5 drive on fdc0 drive 0 ppc0: Standard parallel printer port port 0x378-0x37b irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: Parallel port bus on ppc0 lpt0: Printer on ppbus0 lpt0: Interrupt-driven port sio0: 16550A-compatible COM port port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A npx0: math processor on motherboard npx0: INT 16 interface pmtimer0 on isa0 sc0: System console at flags 0x100 on isa0 sc0: VGA 16 virtual consoles, flags=0x300 sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: Generic ISA VGA at port 0x3c0-0x3df iomem 0xa-0xb on isa0 ulpt0: Canon BJC-2100SP, rev 1.00/1.02, addr 2, iclass 7/1 ulpt0: using bi-directional mode ugen0: Logitech product 0x0920, rev 1.10/0.01, addr 2 ugen1: vendor 0x1131 product 0x1001, rev 1.10/3.73, addr 3 Timecounter TSC frequency 994456955 Hz quality 800 Timecounters tick every 10.000 msec ad0: 38166MB ST340014A/3.06 [77545/16/63] at ata0-master UDMA66 ad1: 76319MB ST380011A/3.06 [155060/16/63] at ata0-slave UDMA66 acd0: CDRW SAMSUNG CD-R/RW SW-232B/R301 at ata1-master PIO4 cd0 at ata1 bus 0 target 0 lun 0 cd0: SAMSUNG CD-R/RW SW-232B R301 Removable CD-ROM SCSI-0 device cd0: 16.000MB/s transfers cd0: cd present [259375 x 2048 byte records] (cd0:ata1:0:0:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ata1:0:0:0): CAM Status: SCSI Status Error (cd0:ata1:0:0:0): SCSI Status: Check Condition (cd0:ata1:0:0:0): ILLEGAL REQUEST asc:64,0 (cd0:ata1:0:0:0): Illegal mode for this track (cd0:ata1:0:0:0): Unretryable error (cd0:ata1:0:0:0): cddone: got error 0x6 back (cd0:ata1:0:0:0): READ(10). CDB: 28 0 0 0 0 1 0 0 1 0 (cd0:ata1:0:0:0): CAM Status: SCSI Status Error (cd0:ata1:0:0:0): SCSI Status: Check Condition
Re: Help with Xorg
Garrett Cooper wrote: On Sep 24, 2005, at 4:32 PM, nawcom wrote: Is the nvidia module being loaded into the kernel? i am assuming so. the devices should be created during bootup. let me know if / dev/nvidia* is being created, or email a boot log. Thanks, Ben Subhro wrote: Hello folks, I am facing a problem in using the nvidia driver with Xorg. I have installed both the versions from the ports tree. When I start X with the nvidia driver, it complains that no GPU was found and subsequently it says that no usable Screens found. I am attaching the Xorg log file, the error which is thrown out while starting X and my xorg.conf. Help is greatly appreciated. Thanks and Best Regards S. -- Subhro Sankha Kar School of Information Technology Block AQ-13/1 Sector V ZIP 700091 India Sounds like the card isn't being detected from what you're saying. Can you give us relevant X outputs (+/-5 lines from the issue, ie warning or error) where it states these problems? Also, the device section for your card and the screen and layout sections from your xorg.conf file would be very helpful. Thanks, -Garrett ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] Thanks fore replying back Garrett. I had already attached the Xorg log file, the error which is there on the screen and the xorg.conf in my original posting. You can take a look here: http://lists.freebsd.org/pipermail/freebsd-questions/2005-September/099700.html Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Downgrading from amd64 to i386
Andrew P. sat at his 'puter and typed on 9/18/2005 1:49: Hello! I use FreeBSD/amd64 6.0 as the only OS on my desktop PC. Having carefully thought over pros and cons, I decided to downgrade to i386 for the time being. What on earth does this mean? This is simply not possible. amd64 is a completely different platform. i386 is a 32 bit platform and amd64 is a 64 bit one. You can upgrade or downgrade from one version to other provided the platform remains constant. But upgrading from one patform to other involves buying and assembling physically different hardware holding different copies of OS. Thanks S. -- -+- | Subhro Sankha Kar \ / | GSM: +919831064613 Egold: 2078232 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Porting from LInux to FreeBSD
Deepak Naidu sat at his 'puter and typed on 9/8/2005 15:16: Hi, Hello :-), I am trying to migrate my mail servers from Fedora core 3 to FreeBSD 5.4, due to performance issue. Cool! Go for it :-) 1)Which is the suitable filesystem ie UFS2, Ext2 etc... for mailing server. I used raiserfs in linux. Which File System's are supported in FreeBSD 5.4 and which is stable for mailing system. How do i enable them in kernel. The native filesystem for FreeBSD 5.x and above is UFS2 which performs exceptionally well IMHO. Reiserfs also has support in FBSD although readonly only. Just something off topic, did you have any reasons for using ReiserFS in Linux and not use EXT2/3? 2)How to i find memory, cpu information in freebsd, apart from TOP. In linux we have free and /pro/cpuinfo. I dont see any files under /proc what information do you need that top does not provide? You can try sysctl -a | more and analyse all the kernel runtime variables. 3) Is SMP support enabled in FreeBSD 5.4, or should I recompile the kernel for the support(what kernel arguments should I use). No SMP by default is not there in the stock kernel. However you can boot up your SMP box with the stock kernel and cimpile SMP support in it. Refer to the handbook for the kernel parameters. Also have a look at /usr/src/sys/arch/conf/GENERIC and /usr/src/sys/arch/conf/NOTES for examples where arch is your architecture (i386,amd64,etc) Welcome to the world of FreeBSD. Thanks S. -- -+- | Subhro Sankha Kar \ / | GSM: +919831064613 Egold: 2078232 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Porting from LInux to FreeBSD
Deepak Naidu sat at his 'puter and typed on 9/8/2005 16:55: Hey Subhro thanx for the info. I used Reiserfs in linux, bcos its reads and writes smaller files faster like file size of 1-5 Mb, basically for mailing solution. I dont know where iam wrong. I have read regarding XFS, in freebsd any info ?. So ok FreeBSD supports UFS1/2, dos, fat, fat32, ext2 reiserfs read only, ok cool... So how do i enable Reiserfs in kernel, and do the partion at install time... http://people.freebsd.org/~rodrigc/xfs/index.html XFS is supported in FBSD. For infomration regarding enabling various stuff in the kernel have a look at /usr/src/sys/conf/NOTES. BTW, your mail client incorrectly marks the replies. Why dont u use thunderbird? Its a really cool client IMHO. Also send a cc to [EMAIL PROTECTED] Thanks S. --- Subhro [EMAIL PROTECTED] wrote: Deepak Naidu sat at his 'puter and typed on 9/8/2005 15:16: Hi, Hello :-), I am trying to migrate my mail servers from Fedora core 3 to FreeBSD 5.4, due to performance issue. Cool! Go for it :-) 1)Which is the suitable filesystem ie UFS2, Ext2 etc... for mailing server. I used raiserfs in linux. Which File System's are supported in FreeBSD 5.4 and which is stable for mailing system. How do i enable them in kernel. The native filesystem for FreeBSD 5.x and above is UFS2 which performs exceptionally well IMHO. Reiserfs also has support in FBSD although readonly only. Just something off topic, did you have any reasons for using ReiserFS in Linux and not use EXT2/3? 2)How to i find memory, cpu information in freebsd, apart from TOP. In linux we have free and /pro/cpuinfo. I dont see any files under /proc what information do you need that top does not provide? You can try sysctl -a | more and analyse all the kernel runtime variables. 3) Is SMP support enabled in FreeBSD 5.4, or should I recompile the kernel for the support(what kernel arguments should I use). No SMP by default is not there in the stock kernel. However you can boot up your SMP box with the stock kernel and cimpile SMP support in it. Refer to the handbook for the kernel parameters. Also have a look at /usr/src/sys/arch/conf/GENERIC and /usr/src/sys/arch/conf/NOTES for examples where arch is your architecture (i386,amd64,etc) Welcome to the world of FreeBSD. Thanks S. -- -+- | Subhro Sankha Kar \ / | GSM: +919831064613 Egold: 2078232 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ Does your mail provider give you FREE antivirus protection? Get Yahoo! Mail http://uk.mail.yahoo.com -- -+- | Subhro Sankha Kar \ / | GSM: +919831064613 Egold: 2078232 \./|MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 (0Y0) |ICQ: 203567534 -- AIM: bsdboy1982 --ooO--(_)--Ooo--+- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Partial web page loading
Andrew Waranowski sat at his 'puter and typed on 8/21/2005 21:31: Hey, I have the same problem over here, except that I can recreate the problem well easily and predictably. I don't know a whole lot about computers but this is very weird. Here's what happened: I have a website that I'm working on in PHP. I have a few pages that have text and image content and when I go to them, they either load completely or partially. If it's only partially loaded, I can refresh the page a few times and then it will show the whole contents of the PHP file it's displaying. At first I thought it had something to do with server caching, but then I found that when the web browser displays the whole page, I can refresh it a few times and it will display only a portion of the page; it cuts off right in the middle of some text. Weird! And I've looked at the HTML very carefully - everything is as it should be. The browser cuts off at a seemingly arbitrary place in the HTML and does not even include the footer.inc file I included. Very very strange. Let me know if you get any kind of insight about the problem. Thanks ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED] If it is not a private page, can we have a look at it? Thanks S. -- -+- \ / | Subhro Sankha Kar \./ | GSM: +919831064613 Egold: 2078232 (0Y0) |MSN:[EMAIL PROTECTED] -- Yahoo: subhro82 --ooO--(_)--Ooo--+- ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Software Router
Hello Folks, One of my clients had asked me to provide a router. I was planning to use an old P1 boxs to make the router. The requirements state that it is for the purpose of internet – vlan communication. The router must have features like encapsulation , creating sub interfaces , enabling port trunking (802.1Q) etc. Is it possible? Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: FreeBSD 6
Nikolas Britton wrote: On 7/28/05, Kris Kennaway [EMAIL PROTECTED] wrote: On Tue, Jul 26, 2005 at 03:00:49PM -0500, Nikolas Britton wrote: The kernel build failed when it tired to compile the r128drm device. Show us the error. cc -c -O2 -pipe -fno-strict-aliasing -Wall -Wredundant-decls -Wnested-externs -Wstrict-prototypes -Wmissing-prototypes -Wpointer-arith -Winline -Wcast-qual -fformat-extensions -std=c99 -nostdinc -I- -I. -I../../.. -I../../../contrib/dev/acpica -I../../../contrib/altq -I../../../contrib/ipfilter -I../../../contrib/pf -I../../../contrib/dev/ath -I../../../contrib/dev/ath/freebsd -I../../../contrib/ngatm -I../../../dev/twa -D_KERNEL -include opt_global.h -fno-common -finline-limit=8000 --param inline-unit-growth=100 --param large-function-growth=1000 -mno-align-long-strings -mpreferred-stack-boundary=2 -mno-mmx -mno-3dnow -mno-sse -mno-sse2 -ffreestanding -Werror vnode_if.c touch hack.c cc -shared -nostdlib hack.c -o hack.So rm -f hack.c MAKE=make sh ../../../conf/newvers.sh GENERIC cc -c -O2 -pipe -fno-strict-aliasing -Wall -Wredundant-decls -Wnested-externs -Wstrict-prototypes -Wmissing-prototypes -Wpointer-arith -Winline -Wcast-qual -fformat-extensions -std=c99 -nostdinc -I- -I. -I../../.. -I../../../contrib/dev/acpica -I../../../contrib/altq -I../../../contrib/ipfilter -I../../../contrib/pf -I../../../contrib/dev/ath -I../../../contrib/dev/ath/freebsd -I../../../contrib/ngatm -I../../../dev/twa -D_KERNEL -include opt_global.h -fno-common -finline-limit=8000 --param inline-unit-growth=100 --param large-function-growth=1000 -mno-align-long-strings -mpreferred-stack-boundary=2 -mno-mmx -mno-3dnow -mno-sse -mno-sse2 -ffreestanding -Werror vers.c linking kernel r128_cce.o(.text+0x354): In function `r128_do_cleanup_cce': : undefined reference to `drm_free' r128_cce.o(.text+0x372): In function `r128_do_cleanup_cce': : undefined reference to `drm_irq_uninstall' r128_cce.o(.text+0x394): In function `r128_do_cleanup_cce': : undefined reference to `drm_ioremapfree' r128_cce.o(.text+0x3a8): In function `r128_do_cleanup_cce': : undefined reference to `drm_ati_pcigart_cleanup' r128_cce.o(.text+0x3d7): In function `r128_do_cleanup_cce': : undefined reference to `drm_ioremapfree' r128_cce.o(.text+0x3e3): In function `r128_do_cleanup_cce': : undefined reference to `drm_ioremapfree' r128_cce.o(.text+0x400): In function `r128_cce_init': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0x4ab): In function `r128_cce_init': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0x4bb): In function `r128_cce_init': : undefined reference to `drm_alloc' r128_cce.o(.text+0x504): In function `r128_cce_init': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0x575): In function `r128_cce_init': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0x7e2): In function `r128_cce_init': : undefined reference to `drm_order' r128_cce.o(.text+0x851): In function `r128_cce_init': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0x8e0): In function `r128_cce_init': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0xa1d): In function `r128_cce_init': : undefined reference to `drm_ioremap' r128_cce.o(.text+0xa2f): In function `r128_cce_init': : undefined reference to `drm_ioremap' r128_cce.o(.text+0xa41): In function `r128_cce_init': : undefined reference to `drm_ioremap' r128_cce.o(.text+0xab3): In function `r128_cce_init': : undefined reference to `drm_ati_pcigart_init' r128_cce.o(.text+0xc08): In function `r128_cce_start': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0xc87): In function `r128_cce_start': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0xd13): In function `r128_cce_stop': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0xe14): In function `r128_cce_reset': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0xea1): In function `r128_cce_reset': : undefined reference to `drm_debug_flag' r128_cce.o(.text+0xedd): more undefined references to `drm_debug_flag' follow r128_drv.o(.text+0xc): In function `r128_probe': : undefined reference to `drm_probe' r128_drv.o(.text+0xca): In function `r128_attach': : undefined reference to `drm_attach' r128_drv.o(.data+0x48): undefined reference to `drm_devclass' r128_drv.o(.data+0x94): undefined reference to `drm_detach' r128_irq.o(.text+0x48): In function `r128_driver_irq_handler': : undefined reference to `drm_vbl_send_signals' r128_state.o(.text+0xb): In function `r128_emit_clip_rects': : undefined reference to `drm_debug_flag' r128_state.o(.text+0x2d0): In function `r128_cce_dispatch_flip': : undefined reference to `drm_debug_flag' r128_state.o(.text+0x523): In function `r128_cce_dispatch_indirect': : undefined reference to `drm_debug_flag' r128_state.o(.text+0x7e4): In function `r128_cce_clear': : undefined reference to `drm_debug_flag' r128_state.o(.text+0x906): In function `r128_cce_clear': : undefined reference to
Re: host is not on local network??
On 7/20/2005 14:33, Odhiambo Washington wrote: Hello FreeBSD users, I am sure I can learn from the expertise available on this list! I know it has some of the best brains in networking. I have several machines on the same physical LAN, but all those machines have been sending me this output in their daily security run output for the past few days: hostname-changed.wananchi.com kernel log messages: arplookup 62.8.72.2 failed: host is not on local network arplookup 62.8.72.2 failed: host is not on local network I have asked our network engineers what they screwed up that led to these messages coming on our servers every night but they are not giving me answers, so I am looking for something to use to hit them where it matters ;) Can someone explain this to me? Sure, however we need some more information. What does the Subnet inside your LAN look like? Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: OSDir.com Screenshots of your FreeBSD 6.0-BETA1 release
On 7/18/2005 11:35, Nikolas Britton wrote: On 7/17/05, Subhro [EMAIL PROTECTED] wrote: FreeBSD is NOT ANOTHER PENGUIN IMPLEMENTATION Secondly, I believe that this concept of posting screenshots is pretty unprofessional and childish. Its like saying Yay! my desktop is prettier than yours. At FreeBSD we concentrate more on quaality than looks. Secondly, FreeBSD does not have any Native GUI unlike few distributions like Mandrake who use a costomized GUI. Thus IMHO a FreeBSD screenshot would just be a black screen with some scribbles on it :-). FreeBSD 6.0-BETA1 Screenshot: FreeBSD/i386 (amnesiac) (ttyv0) login: █ ROFLOL. Good Joke Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: OSDir.com Screenshots of your FreeBSD 6.0-BETA1 release
On 7/18/2005 18:22, Chris wrote: FreeBSD is NOT ANOTHER PENGUIN IMPLEMENTATION Yeah.. I know what *BSD is, smartass. Secondly, I believe that this concept of posting screenshots is pretty unprofessional and childish. Its like saying Yay! my desktop is prettier than yours. At FreeBSD we concentrate more on quaality than looks. Secondly, FreeBSD does not have any Native GUI unlike few distributions like Mandrake who use a costomized GUI. Thus IMHO a FreeBSD screenshot would just be a black screen with some scribbles on it :-). How about some installation screenshots? You will find them in the handbook Installation Chapter. BTW please be kind enough to wrap your mails at 72 chars. You make life miserable for poor souls like me who cant afford more than a old P1 running only CUI. Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: OSDir.com Screenshots of your FreeBSD 6.0-BETA1 release
On 7/18/2005 10:11, Chris wrote: Congratulations on your FreeBSD 6.0-BETA1 release. We'd love to have this release listed in our screenshot gallery (http://shots.osdir.com). Posting your screenshots is an excellent way to promote your product, as submitting is free and our screenshots are seen by thousands of people daily (http://www.stathound.com/stats.aspx?m=d). Thanks If you are interested in submitting screenshots, please follow the instructions on how to submit here: http://shots.osdir.com/slideshows/how_to_submit.php. You may want to post this on your forum to get some help from your community. Thank you. You are most welcome http://shots.osdir.com/slideshows/how_to_submit.php here the first line on this site is: At OSDir, you may also submit http://shots.osdir.com/slideshows/how_to_submit_desktop.php your Linux desktop screenshot! FreeBSD is NOT ANOTHER PENGUIN IMPLEMENTATION Secondly, I believe that this concept of posting screenshots is pretty unprofessional and childish. Its like saying Yay! my desktop is prettier than yours. At FreeBSD we concentrate more on quaality than looks. Secondly, FreeBSD does not have any Native GUI unlike few distributions like Mandrake who use a costomized GUI. Thus IMHO a FreeBSD screenshot would just be a black screen with some scribbles on it :-). -- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Re Custom kernel config questions linux user
On 6/23/2005 20:24, Daniel Gonzalez wrote: Hello, I was wondering if anyone could provide me an answer to the following questions. Please keep in mind that by default I learned Unix on a Linux system, so... please no flames :(. Flames??!! What for? Buddy we have better work to do than say My OS superior than yours:-) Both Linux and *BSD are great OS. 1) Is there any sort of configuration interface (ncurses, X, etc), or am I 'stuck' with 'manually configuring' a textfile? Configuration for what? Some applications do have some kind of GUI (ncurses maybe) interface. But text files work everywhere. Also more convenient when you are on a low bandwidth remote terminal. FreeBSD system. Check out SWAT or I think there may be something called Webmin? Yeh Webmin is a tool. But you need lots of things to work right (for example, apache, a few libraries) to ensure that you can even start up webmin. 2) Is there a complete list of features which can be enabled for the kernel, other what was in the GENERIC configuration file? Of course. Refer to the NOTES (LINT in 4.* family). Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Newbie - Trouble installing OpenOffice
On 6/21/2005 5:58, Lawrence Petrykanyn wrote: Hi! Hello :-), First, I tried to install OpenOffice using the ports collection. The first attempt proceeded successfully for quite a while, but then failed because it was unable to fetch certain files (no file found, access denied), then subsequent attempts failed because it said that a lower version was already installed. Before trying a second time, did you clean up the installation folders using 'make clean'? So I did a pkg_delete which did not work because: pkg_delete couldn't entirely delete package (perhaps the packing list is incorrectly specified?). Didn't get you. What did you try to pkg_delete? So I looked in /var/db/pkg but didn't see an OpenOffice folder. Entirely expected. OpenOffice installation was not registered as it was never completed. Knowing when to quit, I decided to install the package so I downloaded OOo_1.1.3_FreeBSD410Intel410_install.tgz and did pkg_add -r openoffice. It is always a good idea to use prebuilt binaries compared to home made ones for two reasons. First of all if you dont have a very powerful system, it would be a hard time compiling something like KDE or OpenOffice which can very well take days before it finishes off. Secondly, it saves lot of bandwidth. That matters if you are not very rich and bandwidth is costly like it is for me. But the pros of using home made binaries are, you can use optimizations and make the binary hardware specific. This would give a BIG performance gain. Secondly there are a few features which needs to be enabled at compile time. In most of the cases this calls for using the ports. The attempt failed but I did manage to copy the output. It was over ten-thousand lines long, so I just excerpted it: sympatico# pkg_add -r openoffice Fetching, etc... /var: write failed, filesystem is full OpenOffice.org1.1.2/share/cde/types/it.UTF-8/vnd.sun.xml.draw.dt: Can't open OpenOffice.org1.1.2/share/cde/types/it.UTF-8/vnd.sun.xml.draw.dt': No such file or directory /var: write failed, filesystem is full OpenOffice.org1.1.2/share/cde/types/it.UTF-8/vnd.sun.xml.impress.dt: Can't open OpenOffice.org1.1.2/share/cde/types/it.UTF-8/vnd.sun.xml.impress.dt': No such file or directory . . . /var: write failed, filesystem is full OpenOffice.org1.1.2/program/python-core: Can't restore symlink to 'python-core-2.2.2': No space left on device /var: write failed, filesystem is full /var: write failed, filesystem is full Did you have softupdates enabled on your system? Soft updates sometimes defer the release of file descriptors. And if you start using file descriptors too fast then you may run out of available descriptors thus getting this error in spite of the face that there is space on the platters. When I saw the filesystem is full message, I did a df: sympatico# df Filesystem 1K-blocksUsedAvail Capacity Mounted on /dev/ad1s1a253678 119824 11356051% /devfs1 10 100%/dev /dev/ad1s1e253678 16 233368 0%/tmp /dev/ad1s1f 36221772 3195004 3012902810%/usr /dev/ad1s1d253678 1597007368468%/var /dev/ad0s19950544 7666112 228443277%/mnt It really looks to me as if the soft updates is the culprit. May we have a look at 'mount' without the 's? Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Newbie - Trouble installing OpenOffice
On 6/21/2005 20:44, Svein Halvor Halvorsen wrote: * Subhro [2005-06-21 19:23 +0530] sympatico# df Filesystem 1K-blocksUsedAvail Capacity Mounted on /dev/ad1s1a253678 119824 11356051% /devfs1 10 100%/dev /dev/ad1s1e253678 16 233368 0%/tmp /dev/ad1s1f 36221772 3195004 3012902810%/usr /dev/ad1s1d253678 1597007368468%/var /dev/ad0s19950544 7666112 228443277%/mnt It really looks to me as if the soft updates is the culprit. May we have a look at 'mount' without the 's? I don't know how big openoffice is Its about 200M. Thanks S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Kernel Core Dumping
On 6/18/2005 23:40, J T wrote: Just an update on this, everything has been fine since I deleted the file. No more crashes. Strange. -JT On 6/14/05, J T [EMAIL PROTECTED] wrote: Hi, For some reason my machine keeps crashing almost every night at around 3:00am with the following test in the messages log file: Jun 14 03:02:28 taco kernel: pid 7174 (sh), uid 0: exited on signal 11 (core dumped) I tracked it down to cvsup. I run it every night at 3:00am, the following is the log file that I make it create: ===update-os started by root on at Mon Jun 13 03:01:00 2005=== Connected to cvsup.ca.freebsd.org Updating collection src-all/cvs TreeList failed: Error in /usr/local/etc/cvsup/sup/src-all/checkouts.cvs:RELENG_5_3: 37510: File is truncated. Delete it and try again. ===update-os started by root on at Tue Jun 14 03:01:00 2005=== Connected to cvsup.ca.freebsd.org Updating collection src-all/cvs TreeList failed: Error in /usr/local/etc/cvsup/sup/src-all/checkouts.cvs:RELENG_5_3: 37510: File is truncated. Delete it and try again. The following is the 'update-os' script I made: echo ===update-os started by $USER on $HOST at `date +%c`=== /usr/local/etc/cvsup/log/update-os.log #!/bin/sh echo Updating OS sources with cvsup... /usr/local/bin/cvsup /usr/local/etc/cvsup/supfile.os /usr/local/etc/cvsup/log/update-os.log The supfile.os: *default host=cvsup.ca.freebsd.org compress *default release=cvs *default base=/usr/local/etc/cvsup *default prefix=/usr *default delete use-rel-suffix *default tag=RELENG_5_3 src-all I decided to rm the file '/usr/local/etc/cvsup/sup/src-all/checkouts.cvs:RELENG_5_3' just to see if that fixed it. And it did, but why was it crashing the entire box? -- - [EMAIL PROTECTED] I strongly feel that you need to check for BAD RAM modules. Regards S. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
