Re: FreeBSD 6.1 Installation problem
On Wed, 8 Nov 2006 08:02:14 -0700 Mark Maddox wrote: The cable is fine; I installed windows on the drive in the machine that is having problems, just to see if it would work. I'm still trying to get FreeBSD 6.1 up -Original Message- From: Lowell Gilbert [mailto:[EMAIL PROTECTED] Sent: Tuesday, November 07, 2006 8:09 AM To: Mark Maddox Cc: freebsd-questions@freebsd.org Subject: Re: FreeBSD 6.1 Installation problem Mark Maddox [EMAIL PROTECTED] writes: I have an onboard Intel ICH7-M SATA controller with an SATA hard drive and cdrom connected to it. I am unable to install FreeBSD onto the harddrive. According to the FreeBSD website ICH7 has been supported since version 6.0 I have tried putting the controller in Legacy Mode and tried turning turned DMA off in on boot. I have tested both of my SATA ports on the motherboard to make sure they both work with an alternate operating system (Windows) and they both worked. I have also installed the harddrive in another computer and installed FreeBSD on it successfully and then (after testing it and booting successfully on that computer) put it in the machine I am having the problems with only to have it start booting and then error out with harddrive errors. During boot I get this error: ad0: FAILURE -READ_DMA48 status=ffBUSY, READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=390721967 During install the error I get is Error mounting /mnt/dev/ad0s1e on /mnt/tmp : Input/output error ad0: FAILURE - READ_DMA status=ffBUSY,READY, DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=9303631 Anyone have any ideas? Sounds like controller problems. I'd start by replacing the SATA cable. Windows throws those messages away. And you understand it when the data got lost. WBR -- Boris Samorodov (bsam) Research Engineer, http://www.ipt.ru Telephone Internet SP FreeBSD committer, http://www.FreeBSD.org The Power To Serve ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
RE: FreeBSD 6.1 Installation problem
-Original Message- From: Boris Samorodov [mailto:[EMAIL PROTECTED] Sent: Wednesday, November 08, 2006 8:50 AM To: Mark Maddox Cc: freebsd-questions@freebsd.org Subject: Re: FreeBSD 6.1 Installation problem On Wed, 8 Nov 2006 08:02:14 -0700 Mark Maddox wrote: The cable is fine; I installed windows on the drive in the machine that is having problems, just to see if it would work. I'm still trying to get FreeBSD 6.1 up -Original Message- From: Lowell Gilbert [mailto:[EMAIL PROTECTED] Sent: Tuesday, November 07, 2006 8:09 AM To: Mark Maddox Cc: freebsd-questions@freebsd.org Subject: Re: FreeBSD 6.1 Installation problem Mark Maddox [EMAIL PROTECTED] writes: I have an onboard Intel ICH7-M SATA controller with an SATA hard drive and cdrom connected to it. I am unable to install FreeBSD onto the harddrive. According to the FreeBSD website ICH7 has been supported since version 6.0 I have tried putting the controller in Legacy Mode and tried turning turned DMA off in on boot. I have tested both of my SATA ports on the motherboard to make sure they both work with an alternate operating system (Windows) and they both worked. I have also installed the harddrive in another computer and installed FreeBSD on it successfully and then (after testing it and booting successfully on that computer) put it in the machine I am having the problems with only to have it start booting and then error out with harddrive errors. During boot I get this error: ad0: FAILURE -READ_DMA48 status=ffBUSY, READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=390721967 During install the error I get is Error mounting /mnt/dev/ad0s1e on /mnt/tmp : Input/output error ad0: FAILURE - READ_DMA status=ffBUSY,READY, DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=9303631 Anyone have any ideas? Sounds like controller problems. I'd start by replacing the SATA cable. Windows throws those messages away. And you understand it when the data got lost. I just tried a new cable and I get the same errors. Windows worked fine on the machine, but I cannot use Windows for my application. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: FreeBSD 6.1 Installation problem
On Wed, 8 Nov 2006 09:00:30 -0700 Mark Maddox wrote: On Wed, 8 Nov 2006 08:02:14 -0700 Mark Maddox wrote: The cable is fine; I installed windows on the drive in the machine that is having problems, just to see if it would work. I'm still trying to get FreeBSD 6.1 up Mark Maddox [EMAIL PROTECTED] writes: I have an onboard Intel ICH7-M SATA controller with an SATA hard drive and cdrom connected to it. I am unable to install FreeBSD onto the harddrive. According to the FreeBSD website ICH7 has been supported since version 6.0 I have tried putting the controller in Legacy Mode and tried turning turned DMA off in on boot. I have tested both of my SATA ports on the motherboard to make sure they both work with an alternate operating system (Windows) and they both worked. I have also installed the harddrive in another computer and installed FreeBSD on it successfully and then (after testing it and booting successfully on that computer) put it in the machine I am having the problems with only to have it start booting and then error out with harddrive errors. During boot I get this error: ad0: FAILURE -READ_DMA48 status=ffBUSY, READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=390721967 During install the error I get is Error mounting /mnt/dev/ad0s1e on /mnt/tmp : Input/output error ad0: FAILURE - READ_DMA status=ffBUSY,READY, DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=9303631 Anyone have any ideas? Sounds like controller problems. I'd start by replacing the SATA cable. Windows throws those messages away. And you understand it when the data got lost. I just tried a new cable and I get the same errors. Windows worked fine on the machine, but I cannot use Windows for my application. Do you have any check utility for your harddrive? Can you try the latest FreeBSD iso installation CD (seems it's a BETA-3 now)? Not for a production use but at least to test. WBR -- Boris Samorodov (bsam) Research Engineer, http://www.ipt.ru Telephone Internet SP FreeBSD committer, http://www.FreeBSD.org The Power To Serve ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
RE: FreeBSD 6.1 Installation problem
-Original Message- From: Boris Samorodov [mailto:[EMAIL PROTECTED] Sent: Wednesday, November 08, 2006 9:21 AM To: Mark Maddox Cc: freebsd-questions@freebsd.org Subject: Re: FreeBSD 6.1 Installation problem On Wed, 8 Nov 2006 09:00:30 -0700 Mark Maddox wrote: On Wed, 8 Nov 2006 08:02:14 -0700 Mark Maddox wrote: The cable is fine; I installed windows on the drive in the machine that is having problems, just to see if it would work. I'm still trying to get FreeBSD 6.1 up Mark Maddox [EMAIL PROTECTED] writes: I have an onboard Intel ICH7-M SATA controller with an SATA hard drive and cdrom connected to it. I am unable to install FreeBSD onto the harddrive. According to the FreeBSD website ICH7 has been supported since version 6.0 I have tried putting the controller in Legacy Mode and tried turning turned DMA off in on boot. I have tested both of my SATA ports on the motherboard to make sure they both work with an alternate operating system (Windows) and they both worked. I have also installed the harddrive in another computer and installed FreeBSD on it successfully and then (after testing it and booting successfully on that computer) put it in the machine I am having the problems with only to have it start booting and then error out with harddrive errors. During boot I get this error: ad0: FAILURE -READ_DMA48 status=ffBUSY, READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=390721967 During install the error I get is Error mounting /mnt/dev/ad0s1e on /mnt/tmp : Input/output error ad0: FAILURE - READ_DMA status=ffBUSY,READY, DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=9303631 Anyone have any ideas? Sounds like controller problems. I'd start by replacing the SATA cable. Windows throws those messages away. And you understand it when the data got lost. I just tried a new cable and I get the same errors. Windows worked fine on the machine, but I cannot use Windows for my application. Do you have any check utility for your harddrive? Can you try the latest FreeBSD iso installation CD (seems it's a BETA-3 now)? Not for a production use but at least to test. I have tried both the 6.1 release and the 6.2 BETA3. Both get the same errors. I have not used any hard drive check utilities on the drive but I did put the hard drive with the same SATA cable attached to it in a computer with an ICH6 controller and 6.1 installed just fine. Then after booting up and making sure everything worked I moved the hard drive back to the computer with the ICH7 controller and I got the same errors during boot and boot failed. Any ideas? Thanks, Mark ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: FreeBSD 6.1 Installation problem
On Wed, 8 Nov 2006 09:29:36 -0700 Mark Maddox wrote: On Wed, 8 Nov 2006 09:00:30 -0700 Mark Maddox wrote: On Wed, 8 Nov 2006 08:02:14 -0700 Mark Maddox wrote: The cable is fine; I installed windows on the drive in the machine that is having problems, just to see if it would work. I'm still trying to get FreeBSD 6.1 up Mark Maddox [EMAIL PROTECTED] writes: I have an onboard Intel ICH7-M SATA controller with an SATA hard drive and cdrom connected to it. I am unable to install FreeBSD onto the harddrive. According to the FreeBSD website ICH7 has been supported since version 6.0 I have tried putting the controller in Legacy Mode and tried turning turned DMA off in on boot. I have tested both of my SATA ports on the motherboard to make sure they both work with an alternate operating system (Windows) and they both worked. I have also installed the harddrive in another computer and installed FreeBSD on it successfully and then (after testing it and booting successfully on that computer) put it in the machine I am having the problems with only to have it start booting and then error out with harddrive errors. During boot I get this error: ad0: FAILURE -READ_DMA48 status=ffBUSY, READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=390721967 During install the error I get is Error mounting /mnt/dev/ad0s1e on /mnt/tmp : Input/output error ad0: FAILURE - READ_DMA status=ffBUSY,READY, DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=9303631 Anyone have any ideas? Sounds like controller problems. I'd start by replacing the SATA cable. Windows throws those messages away. And you understand it when the data got lost. I just tried a new cable and I get the same errors. Windows worked fine on the machine, but I cannot use Windows for my application. Do you have any check utility for your harddrive? Can you try the latest FreeBSD iso installation CD (seems it's a BETA-3 now)? Not for a production use but at least to test. I have tried both the 6.1 release and the 6.2 BETA3. Both get the same errors. I have not used any hard drive check utilities on the drive but I did put the hard drive with the same SATA cable attached to it in a computer with an ICH6 controller and 6.1 installed just fine. Then after booting up and making sure everything worked I moved the hard drive back to the computer with the ICH7 controller and I got the same errors during boot and boot failed. Any ideas? Only one. Open a PR, write all that info. BTW, if FreeBSD live CD can be executed with verbose dmesg, it may help. I think this PR have a good chances to be closed since there is a pre-release cycle now and ich7 controller is widely used. Sorry for not being very helpful. :-( WBR -- Boris Samorodov (bsam) Research Engineer, http://www.ipt.ru Telephone Internet SP FreeBSD committer, http://www.FreeBSD.org The Power To Serve ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: FreeBSD 6.1 Installation problem
Mark Maddox [EMAIL PROTECTED] writes: I have an onboard Intel ICH7-M SATA controller with an SATA hard drive and cdrom connected to it. I am unable to install FreeBSD onto the harddrive. According to the FreeBSD website ICH7 has been supported since version 6.0 I have tried putting the controller in Legacy Mode and tried turning turned DMA off in on boot. I have tested both of my SATA ports on the motherboard to make sure they both work with an alternate operating system (Windows) and they both worked. I have also installed the harddrive in another computer and installed FreeBSD on it successfully and then (after testing it and booting successfully on that computer) put it in the machine I am having the problems with only to have it start booting and then error out with harddrive errors. During boot I get this error: ad0: FAILURE -READ_DMA48 status=ffBUSY, READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=390721967 During install the error I get is Error mounting /mnt/dev/ad0s1e on /mnt/tmp : Input/output error ad0: FAILURE - READ_DMA status=ffBUSY,READY, DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR error=0 LBA=9303631 Anyone have any ideas? Sounds like controller problems. I'd start by replacing the SATA cable. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
