Re: Kismet on FreeBSD 7.0-STABLE
On 11/6/08, Ludovit Koren <[EMAIL PROTECTED]> wrote:
>
>> On Thu, 06 Nov 2008 13:12:23 +0100
>> [EMAIL PROTECTED]("Paul B. Mahol") said:
>>
>> On 11/6/08, Ludovit Koren <[EMAIL PROTECTED]> wrote:
>> >
>> >
>> > Hi,
>> >
>> > I am using
>> >
>> > iwi0: mem 0xfafef000-0xfafe irq 9 at
>> > device 3.0 on pci2
>> >
>> >
>> > # kldload /boot/kernel/if_iwi.ko
>> > # kldload /boot/kernel/iwi_bss.ko
>> > # kldload /boot/kernel/iwi_ibss.ko
>> > # kldload /boot/kernel/iwi_monitor.ko
>> > # /etc/rc.d/wpa_supplicant start iwi0
>> >
>> > which is working fine when I am using it connecting to WiFi net. When
>> > I am using wpa_cli scan and scan_results I can see different nets.
>> >
>> > I have the following configuration line in the kismet.conf file:
>> >
>> > source=radiotap_bsd_ab,iwi0,pcapfile
>>
>> It should be:
>>
>> source=radiotap_bsd_ab,iwi0,iwi0
>
> I tried it even with this, no success
>
>>
>> More information is required. Can you put iwi0 into monitor mode and
>> use tcpdump instead?
>>
>> ifconfig iwi0 monitor
>>
>
> I cannot capture any packet.
Then it is iwi driver problem.
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: Kismet on FreeBSD 7.0-STABLE
> On Thu, 06 Nov 2008 13:12:23 +0100
> [EMAIL PROTECTED]("Paul B. Mahol") said:
>
> On 11/6/08, Ludovit Koren <[EMAIL PROTECTED]> wrote:
> >
> >
> > Hi,
> >
> > I am using
> >
> > iwi0: mem 0xfafef000-0xfafe irq 9 at
> > device 3.0 on pci2
> >
> >
> > # kldload /boot/kernel/if_iwi.ko
> > # kldload /boot/kernel/iwi_bss.ko
> > # kldload /boot/kernel/iwi_ibss.ko
> > # kldload /boot/kernel/iwi_monitor.ko
> > # /etc/rc.d/wpa_supplicant start iwi0
> >
> > which is working fine when I am using it connecting to WiFi net. When
> > I am using wpa_cli scan and scan_results I can see different nets.
> >
> > I have the following configuration line in the kismet.conf file:
> >
> > source=radiotap_bsd_ab,iwi0,pcapfile
>
> It should be:
>
> source=radiotap_bsd_ab,iwi0,iwi0
I tried it even with this, no success
>
> More information is required. Can you put iwi0 into monitor mode and
> use tcpdump instead?
>
> ifconfig iwi0 monitor
>
I cannot capture any packet.
lk
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: Kismet on FreeBSD 7.0-STABLE
Ludovit wrote: > iwi0: mem 0xfafef000-0xfafe irq 9 > at device 3.0 on pci2 Monitor is broken on iwi on FreeBSD 7. I did report it during the 7.0-BETA, but there was at least one more report in the meantime. With exactly the same setup, I can use kismet with ural (ok), zyd (many broken packages), ral (ok), and ath (good, but see below). I do not receive a single package with iwi. I did replace my iwi miniPCI device by an ath one, which is more reliable anyhow. (iwi, as all Intel cards, occasionally dies and cannot reload firmware because of too little dma memory. That was reported a few times, too.) ath can monitor, even for longer periods of time, but if I do channel hopping in kismet, it often eventually stops receiving packages after a few minutes. Restarting kismet always fixes that. (I have had that with different ath cards.) iwi monitoring did work on 6.2, but often the card would not do regular networking after that until reboot and the problem with the firmware mentioned above was already present, although it was much better than on 6.1. For monitoring, you should either get a different card or try 6.X, 6-STABLE, or maybe 8-CURRENT. (I have no experience with the latter.) Cheers, Jan Henrik ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: Kismet on FreeBSD 7.0-STABLE
On 11/6/08, Ludovit Koren <[EMAIL PROTECTED]> wrote: > > > Hi, > > I am using > > iwi0: mem 0xfafef000-0xfafe irq 9 at > device 3.0 on pci2 > > > # kldload /boot/kernel/if_iwi.ko > # kldload /boot/kernel/iwi_bss.ko > # kldload /boot/kernel/iwi_ibss.ko > # kldload /boot/kernel/iwi_monitor.ko > # /etc/rc.d/wpa_supplicant start iwi0 > > which is working fine when I am using it connecting to WiFi net. When > I am using wpa_cli scan and scan_results I can see different nets. > > I have the following configuration line in the kismet.conf file: > > source=radiotap_bsd_ab,iwi0,pcapfile It should be: source=radiotap_bsd_ab,iwi0,iwi0 More information is required. Can you put iwi0 into monitor mode and use tcpdump instead? ifconfig iwi0 monitor ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
