Re: System reboot afther shutdown -p
On Sun, Feb 15, 2004 at 12:53:42AM +0100, Alex de Kruijff wrote: Howdy, I have a problem with powering down my system. When I give the command shutdown -p now then the system powers down, waits a couple of seconds and the reboots. I've checked the BIOS but can't find anything wrong with it. I was wondering if anything i can do to fix this? I did look in the BIOS but couldn't find anything. Or if there isn't implemented something in to the ACPI driver of FreeBSD? I also googled but didn't find anything. I like to add that the system doesn't show this behavure when its not setup to wake upt at any time (in my case 19h). Tanks in advanced for anwsering Alex # uname -a FreeBSD alex.lan 5.2-RELEASE-p2 FreeBSD 5.2-RELEASE-p2 #1: Wed Feb 11 09:43:00 CET 2004 [EMAIL PROTECTED]:/temp/obj/usr/src/sys/I686 i386 # dmesg Preloaded elf kernel /boot/kernel/kernel at 0xc0a78000. Preloaded elf module /boot/kernel/acpi.ko at 0xc0a781f4. Timecounter i8254 frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.60GHz (2605.92-MHz 686-class CPU) Origin = GenuineIntel Id = 0xf29 Stepping = 9 Features=0xbfebfbffFPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE Hyperthreading: 2 logical CPUs real memory = 536805376 (511 MB) avail memory = 511766528 (488 MB) ACPI APIC Table: IntelR AWRDACPI FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 2 ioapic0 Version 2.0 irqs 0-23 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: math processor on motherboard npx0: INT 16 interface acpi0: IntelR AWRDACPI on motherboard pcibios: BIOS version 2.10 Using $PIR table, 11 entries at 0xc00fde90 acpi0: Power Button (fixed) Timecounter ACPI-fast frequency 3579545 Hz quality 1000 acpi_timer0: 24-bit timer at 3.579545MHz port 0x408-0x40b on acpi0 acpi_cpu0: CPU port 0x530-0x537 on acpi0 acpi_cpu1: CPU port 0x530-0x537 on acpi0 acpi_tz0: Thermal Zone port 0x530-0x537 on acpi0 acpi_button0: Power Button on acpi0 pcib0: ACPI Host-PCI bridge port 0xcf8-0xcff on acpi0 pci0: ACPI PCI bus on pcib0 agp0: Intel 82865 host to AGP bridge mem 0xe800-0xefff at device 0.0 o n pci0 pcib1: PCI-PCI bridge at device 1.0 on pci0 pci1: PCI bus on pcib1 pcib1: slot 0 INTA is routed to irq 16 pci1: display, VGA at device 0.0 (no driver attached) uhci0: Intel 82801EB (ICH5) USB controller USB-A port 0xac00-0xac1f irq 16 at device 29.0 on pci0 usb0: Intel 82801EB (ICH5) USB controller USB-A on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: Intel 82801EB (ICH5) USB controller USB-B port 0xa000-0xa01f irq 19 at device 29.1 on pci0 usb1: Intel 82801EB (ICH5) USB controller USB-B on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: Intel 82801EB (ICH5) USB controller USB-C port 0xa400-0xa41f irq 18 at device 29.2 on pci0 usb2: Intel 82801EB (ICH5) USB controller USB-C on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: Intel 82801EB (ICH5) USB controller USB-D port 0xa800-0xa81f irq 16 at device 29.3 on pci0 usb3: Intel 82801EB (ICH5) USB controller USB-D on uhci3 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered pci0: serial bus, USB at device 29.7 (no driver attached) pcib2: ACPI PCI-PCI bridge at device 30.0 on pci0 pci2: ACPI PCI bus on pcib2 xl0: 3Com 3c905C-TX Fast Etherlink XL port 0x9000-0x907f mem 0xfb00-0xfb00 007f irq 20 at device 0.0 on pci2 xl0: Ethernet address: 00:0a:48:0b:0d:9d xl0: no PHY found! device_probe_and_attach: xl0 attach returned 6 xl0: 3Com 3c905C-TX Fast Etherlink XL port 0x9400-0x947f mem 0xfb001000-0xfb00 107f irq 19 at device 5.0 on pci2 xl0: Ethernet address: 00:01:02:dc:30:b3 miibus0: MII bus on xl0 xlphy0: 3c905C 10/100 internal PHY on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isab0: PCI-ISA bridge at device 31.0 on pci0 isa0: ISA bus on isab0 atapci0: Intel ICH5 UDMA100 controller port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0- 0x7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: serial bus, SMBus at device 31.3 (no driver attached) pcm0: Intel ICH5 (82801EB) port 0xb800-0xb83f,0xb400-0xb4ff mem 0xfc002000-0xf c0020ff,0xfc001000-0xfc0011ff irq 17 at device 31.5 on pci0 pcm0: Avance Logic ALC655 AC97 Codec fdc0: Enhanced floppy controller (i82077, NE72065 or clone) port 0x3f7,0x3f0-0 x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: 1440-KB 3.5
System reboot afther shutdown -p
Howdy, I have a problem with powering down my system. When I give the command shutdown -p now then the system powers down, waits a couple of seconds and the reboots. I've checked the BIOS but can't find anything wrong with it. I was wondering if anything i can do to fix this? I did look in the BIOS but couldn't find anything. Or if there isn't implemented something in to the ACPI driver of FreeBSD? I also googled but didn't find anything. # uname -a FreeBSD alex.lan 5.2-RELEASE-p2 FreeBSD 5.2-RELEASE-p2 #1: Wed Feb 11 09:43:00 CET 2004 [EMAIL PROTECTED]:/temp/obj/usr/src/sys/I686 i386 # dmesg Preloaded elf kernel /boot/kernel/kernel at 0xc0a78000. Preloaded elf module /boot/kernel/acpi.ko at 0xc0a781f4. Timecounter i8254 frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.60GHz (2605.92-MHz 686-class CPU) Origin = GenuineIntel Id = 0xf29 Stepping = 9 Features=0xbfebfbffFPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE Hyperthreading: 2 logical CPUs real memory = 536805376 (511 MB) avail memory = 511766528 (488 MB) ACPI APIC Table: IntelR AWRDACPI FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 2 ioapic0 Version 2.0 irqs 0-23 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: math processor on motherboard npx0: INT 16 interface acpi0: IntelR AWRDACPI on motherboard pcibios: BIOS version 2.10 Using $PIR table, 11 entries at 0xc00fde90 acpi0: Power Button (fixed) Timecounter ACPI-fast frequency 3579545 Hz quality 1000 acpi_timer0: 24-bit timer at 3.579545MHz port 0x408-0x40b on acpi0 acpi_cpu0: CPU port 0x530-0x537 on acpi0 acpi_cpu1: CPU port 0x530-0x537 on acpi0 acpi_tz0: Thermal Zone port 0x530-0x537 on acpi0 acpi_button0: Power Button on acpi0 pcib0: ACPI Host-PCI bridge port 0xcf8-0xcff on acpi0 pci0: ACPI PCI bus on pcib0 agp0: Intel 82865 host to AGP bridge mem 0xe800-0xefff at device 0.0 o n pci0 pcib1: PCI-PCI bridge at device 1.0 on pci0 pci1: PCI bus on pcib1 pcib1: slot 0 INTA is routed to irq 16 pci1: display, VGA at device 0.0 (no driver attached) uhci0: Intel 82801EB (ICH5) USB controller USB-A port 0xac00-0xac1f irq 16 at device 29.0 on pci0 usb0: Intel 82801EB (ICH5) USB controller USB-A on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: Intel 82801EB (ICH5) USB controller USB-B port 0xa000-0xa01f irq 19 at device 29.1 on pci0 usb1: Intel 82801EB (ICH5) USB controller USB-B on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: Intel 82801EB (ICH5) USB controller USB-C port 0xa400-0xa41f irq 18 at device 29.2 on pci0 usb2: Intel 82801EB (ICH5) USB controller USB-C on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: Intel 82801EB (ICH5) USB controller USB-D port 0xa800-0xa81f irq 16 at device 29.3 on pci0 usb3: Intel 82801EB (ICH5) USB controller USB-D on uhci3 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered pci0: serial bus, USB at device 29.7 (no driver attached) pcib2: ACPI PCI-PCI bridge at device 30.0 on pci0 pci2: ACPI PCI bus on pcib2 xl0: 3Com 3c905C-TX Fast Etherlink XL port 0x9000-0x907f mem 0xfb00-0xfb00 007f irq 20 at device 0.0 on pci2 xl0: Ethernet address: 00:0a:48:0b:0d:9d xl0: no PHY found! device_probe_and_attach: xl0 attach returned 6 xl0: 3Com 3c905C-TX Fast Etherlink XL port 0x9400-0x947f mem 0xfb001000-0xfb00 107f irq 19 at device 5.0 on pci2 xl0: Ethernet address: 00:01:02:dc:30:b3 miibus0: MII bus on xl0 xlphy0: 3c905C 10/100 internal PHY on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isab0: PCI-ISA bridge at device 31.0 on pci0 isa0: ISA bus on isab0 atapci0: Intel ICH5 UDMA100 controller port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0- 0x7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: serial bus, SMBus at device 31.3 (no driver attached) pcm0: Intel ICH5 (82801EB) port 0xb800-0xb83f,0xb400-0xb4ff mem 0xfc002000-0xf c0020ff,0xfc001000-0xfc0011ff irq 17 at device 31.5 on pci0 pcm0: Avance Logic ALC655 AC97 Codec fdc0: Enhanced floppy controller (i82077, NE72065 or clone) port 0x3f7,0x3f0-0 x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: 1440-KB 3.5 drive on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: Parallel port bus on ppc0 plip0: PLIP network interface on ppbus0 lpt0: Printer on ppbus0 lpt0:
