Re: ZFS performance on 7.2-release/amd64 low compared to UFS2 + SoftUpdates

The difference in layout can easily explain a 2x difference in sequential transfer performance. I seriously doubt your disk is really getting 23K seeks/s done in the UFS case - 100/s sounds much more reasonable for real hardware. Perhaps the results of caching? Joe Koberg Dan Naumov

Re: 6.4 RC1 locks up solid on first reboot

when using customized compiler options in /etc/make.conf . Rebuilding without compiler options fixed the issue. Joe Koberg joe at osoft dot us ___ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To

Re: fxp performance with POLLING

Pete French wrote: However, ethernet at 100Mbit is 4B5B coded at a 125mhz rate. So the raw Errr, 4B5B *is* 10 bits per byte surely? ... Gig ether is mainly 8B10, as is Firewire, SATA, FibreChannel and a Mind you, it assumes that you know the real bit rate, which in the case of 100baseT is

Re: fxp performance with POLLING

00+20))) or 12.34Mbyte/s. Even in the later days of modems this rule applied less and less, because the modulation schemes became synchronous. Joe Koberg joe_at_osoft_dot_us ___ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/lis

Re: HP ProLiant DL360 G5 success stories?

Johan Ström wrote: But.. http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/c00553302/c00553302.pdf seems to tell me that in basic mode I can only access BIOS (pre-OS) using the Remote Console feature, and that after POST I have to have the advanced licensed option? I don't do t

Re: HP ProLiant DL360 G5 success stories?

sing it to our Avocent IP KVMs. Joe Koberg joe at osoft dot us Johan Ström wrote: First of all, nice with all these positive answers! Thank you all (without responding to each and every post:))! On Mar 12, 2008, at 12:35 PM, Pete French wrote: What I'm looking at is a DL360 G5, probab

Re: 7.0-STABLE amd64 kernel trap during boot-time device probe

t I might be able to arrange access to for anyone who has the skill to find/fix the issue. Joe Koberg joe at osoft dot us Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 00 fault virtual address = 0x258 fault code = supervisor read data, page not present

Re: Dell hardware raid 0 (sas5ir) or gmirror?

t-)swap will initiate the rebuild. There is a CLI tool (megarc) in ports/sysutils/megarc but I haven't tried to use it yet. All in all I would recommend the PERC/5i. Joe Koberg joe at osoft dot us Jan 7 06:41:41 fw2 kernel: mfi0: 316 (4278190093s/0x0008/0) - Battery Present Jan 7

Re: The need for initialising disks before use?

necessary Unfortunately I can't find it now. Joe Koberg joe at osoft dot us ___ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[EMAIL PROTECTED]"

loader(8) crashing in 5.4, 5.3 loader works Dell Poweredge SC1425 nocona

crashes. The system is working with the 5.3 loader copied over to /boot/loader. I would like to not have to worry about this the next time I upgrade. Ideas appreciated. Joe Koberg Open Software Services, LLC joe at osoft dot us dmesg: Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c

Re: ATA Woes.

nd here. I install SATA drives in duplicate and triplicate for this reason. Preferably in removable bays with a fan. I assume they're bad out of the box... I write them full of zeros with DD, then read it all back, then do it again. If I don't get read errors then I instal

Re: gvinum or vinum in 5.3-STABLE

fixes the problem until the next reboot: Once the plexes are UP, issue a 'gvinum saveconfig'. Then try rebooting and see what happens. This has worked for me before with 5.3-R, and today with a recent 5.3-STABLE. Joe Koberg [EMAIL PROTECTED] gvinum setstate up storage.p0.s0 gvinu

Re: TIMEOUT - WRITE_DMA - A possible FIX! turn off ACPI

en dd'ing for a half hour. I hope this report helps someone! Joe Koberg joe at osoft dot us dmesg: FreeBSD 5.3-RELEASE #0: Fri Nov 5 04:19:18 UTC 2004 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Pentium II/Pentium II

PC card problems on 5.3-R: "CIS is too long -- truncating""pccard0:Orinoco Gold, SMC 2532W-B

d controller. The wi cards work OK under PCIC mode in NetBSD 1.6.2. The 3com card does not. NetBSD does not seem to work with them in cardbus mode. Thanks in advance for any help Joe Koberg joe at osoft dot us ___ [EMAIL PROTECTED] mailing list http://li

Re: freebsd 5.3 have any problem with vinum ?

ago. jim Joe Koberg joe at osoft dot us ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Re: newfs -v on vinum raid5 panics system (4.10-p3 RELEASE)

ot. I may also be totally wrong. Joe Koberg joe at osoft dot us ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[EMAIL PROTECTED]"