島根大学の阪本です。ダイジェストで読んでいたのですが、メールを受け付け
てくれないようで、あらためてsubscribeしなおしました。
NECのVersaPro J(VJ14M/EX-W)というノートパソコンに、FreeBSD Release6.0
をインストールしました。コンソールモードでは問題なさそうなのですが、X
を起動すると、本体のポインティングデバイスを認識してくれません。マウス
カーソーは表示されますが、全く動かず、また、ボタンも効かないようです。
dmesgを見てみると、psmを認識していないようです。/dev にもpsm0はできて
いません。「OSM」誌2005年12月号のKNOPPIX4.0.2を起動すると問題無く、Xが
使える様です。
家の少し古い型番のパソコン(同じVersaPro)でusb接続の光学マウスをつない
だのをFreeSBIEを使って起動するとマウスが認識されましたが、本体内蔵のポ
インティングデバイスは同様に認識されませんでした。試していませんが、多
分このパソコンでも、USBマウスなら使えそうです。
なんとか、USBマウスをつけずに本体のポインティングデバイスを使いたいの
ですが、同様の事例で、解決策を見つけられた方はおられないでしょうか。あ
るいは、何かのヒントがいただければ喜びます。ちょっと長いですがKNOPPIX、
FreeSBIE、FreeBSD6.0のdmesgを添付します。
_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/
_/ De SAKAMOTO Jiro 阪本滋郎
_/ Dept. of Physics 島根大学総合理工学部物質科学科
_/ Shimane University
_/ [EMAIL PROTECTED], http://maverick.riko.shimane-u.ac.jp
Linux version 2.6.12 ([EMAIL PROTECTED]) (gcc-Version 3.3.6 (Debian 1:3.3.6-7))
#2 SMP Tue Aug 9 23:20:52 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f6e0000 (usable)
BIOS-e820: 000000000f6e0000 - 000000000f6eb000 (ACPI data)
BIOS-e820: 000000000f6eb000 - 000000000f700000 (ACPI NVS)
BIOS-e820: 000000000f700000 - 0000000010000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
246MB LOWMEM available.
On node 0 totalpages: 63200
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 59104 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 NEC ) @ 0x000f80d0
ACPI: RSDT (v001 NEC ND000123 0x00000001 MSFT 0x0100000e) @ 0x0f6e57be
ACPI: FADT (v001 NEC ND000123 0x00000001 MSFT 0x0100000e) @ 0x0f6eaf64
ACPI: BOOT (v001 NEC ND000123 0x00000001 MSFT 0x0100000e) @ 0x0f6eafd8
ACPI: SSDT (v001 SataRe SataPri 0x00001000 INTL 0x20030224) @ 0x0f6e6022
ACPI: SSDT (v001 SataRe SataSec 0x00001000 INTL 0x20030224) @ 0x0f6e5990
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x0f6e57f6
ACPI: DSDT (v001 NEC ND000123 0x00000001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 10000000 (gap: 10000000:d0000000)
Built 1 zonelists
Kernel command line: ### isk_size=100000 init=/etc/init lang=ja apm=power-off
vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (012f0000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1396.791 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244696k/252800k available (1882k kernel code, 7544k reserved, 999k
data, 296k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2752.51 BogoMIPS (lpj=1376256)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9f9ff 00100000 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: afe9f9ff 00100000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9f9ff 00100000 00000000 00000040 00000000
00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: setting ELCR to 0200 (from 0ca0)
CPU0: Intel(R) Celeron(R) M processor 1.40GHz stepping 08
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 845k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd88a, last bus=6
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 6 7 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5 6 7 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 6 *7 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 7 *10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 5 6 7 10 *11)
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1142000068.868:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xc0000000, mapped to 0xd0080000, using 3072k, total
7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.11 loaded.
ahci version 1.00
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 10 (level, low) ->
IRQ 10
ahci: probe of 0000:00:1f.2 failed with error -12
ata_piix version 1.03
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 10 (level, low) ->
IRQ 10
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18B0 irq 14
ata1: dev 0 cfg 49:0f00 82:746b 83:7fe9 84:4023 85:f469 86:3c49 87:4023 88:203f
ata1: dev 0 ATA, max UDMA/100, 117210240 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: HTS541060G9AT00 Rev: MBBO
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sda4: <bsd: sda5 sda6 sda7 sda8 sda9 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 16Kbytes
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI wakeup devices:
LID LAN MODM
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
USB UHCI #1
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001820
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
USB UHCI #2
input: AT Translated Set 2 keyboard on isa0060/serio0
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 10, io base 0x00001840
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ
7
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
USB UHCI #3
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 7, io base 0x00001860
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
USB UHCI #4
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 10, io base 0x00001880
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:06:07.1[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ
5
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[b0104000-b01047ff] Max
Packet=[2048]
sbp2: $Rev: 1219 $ Ben Collins <[EMAIL PROTECTED]>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
alps.c: Enabling hardware tapping
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00004ce04c7171ea]
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.02
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 29859 blocks, 65536 bytes/block, largest block
is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
Registering unionfs 20050921-1517
Freeing unused kernel memory: 296k freed
Generic RTC Driver v1.07
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN0] (on)
ACPI: Fan [FAN1] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (42 C)
ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt 0000:06:07.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
IRQ 10
Yenta: CardBus bridge found at 0000:06:07.0 [1033:82ca]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:07.0, mfunc 0x01771c22, devctl 0x64
Yenta: ISA IRQ mask 0x0058, PCI irq 10
Socket status: 30000006
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
hw_random: RNG not detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:06:09.0[A] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ
7
eth0: RealTek RTL8139 at 0xd052e800, 00:0d:5e:e2:82:49, IRQ 7
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:1e.2[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ
5
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 49104 usecs
intel8x0: clocking to 48000
NTFS driver 2.1.22 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
mtrr: no more MTRRs available
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #1: Thu Nov 11 14:28:23 JST 2004
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) M processor 1.40GHz (1396.51-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8
Features=0xafe9f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
real memory = 258867200 (246 MB)
avail memory = 235274240 (224 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <NEC ND000123> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU (3 Cx states)> port 0x530-0x537 on acpi0
acpi_tz0: <Thermal Zone> port 0x530-0x537 on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <display> at device 2.1 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0x1820-0x183f irq 11 at device 29.0
on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x1840-0x185f irq 10 at device 29.1
on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x1860-0x187f irq 7 at device 29.2
on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x1880-0x189f irq 10 at device 29.3
on pci0
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib1
cbb0: <TI4510 PCI-CardBus Bridge> at device 7.0 on pci6
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem
0xb0100000-0xb0103fff,0xb0104000-0xb01047ff irq 5 at device 7.1 on pci6
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:e0:4c:71:71:ea
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:71:71:ea
fwe0: Ethernet address: 02:00:4c:71:71:ea
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem 0xb0104800-0xb01048ff
irq 7 at device 9.0 on pci6
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:0d:5e:e2:82:49
pcm0: <Intel ICH6 (82801FB)> port 0x18c0-0x18ff,0x1c00-0x1cff mem
0xb0040400-0xb00404ff,0xb0040800-0xb00409ff irq 5 at device 30.2 on pci0
pcm0: [GIANT-LOCKED]
pcm0: <Analog Devices AD1981B AC97 Codec>
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <GENERIC ATA controller> port
0x18b0-0x18bf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.2 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
speaker0: <PC speaker> port 0x61 on acpi0
orm0: <ISA Option ROMs> at iomem 0xe3000-0xe3fff,0xd0000-0xd3fff on isa0
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1396511355 Hz quality 800
Timecounters tick every 10.000 msec
md0: Preloaded image </boot/mfsroot> 7340032 bytes at 0xc0aba20c
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ad0: 57231MB <HTS541060G9AT00/MBBOA60A> [116280/16/63] at ata0-master UDMA33
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4244N/1.00> at ata1-master UDMA33
Mounting root from ufs:/dev/md0
md1.uzip: 2458 x 65536 blocks
md2.uzip: 12633 x 65536 blocks
md3.uzip: 11307 x 65536 blocks
md4.uzip: 337 x 65536 blocks
md5.uzip: 1515 x 65536 blocks
ipfw2 initialized, divert disabled, rule-based forwarding disabled, default to
deny, logging disabled
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #1: Thu Mar 9 15:14:45 JST 2006
[EMAIL PROTECTED]:/usr/src/sys/i386/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) M processor 1.40GHz (1396.51-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8
Features=0xafe9f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
AMD Features=0x100000<NX>
real memory = 258867200 (246 MB)
avail memory = 243834880 (232 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <NEC ND000123> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
pci_link0: <ACPI PCI Link LNKA> irq 10 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 5 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 7 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 10 on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0
pci_link5: <ACPI PCI Link LNKF> irq 0 on acpi0
pci_link6: <ACPI PCI Link LNKG> irq 0 on acpi0
pci_link7: <ACPI PCI Link LNKH> irq 11 on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0x1820-0x183f
irq 11 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0x1840-0x185f
irq 10 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0x1860-0x187f
irq 7 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0x1880-0x189f
irq 10 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xb0040000-0xb00403ff irq 11 at
device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib1
cbb0: <TI4510 PCI-CardBus Bridge> at device 7.0 on pci6
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem
0xb0104000-0xb01047ff,0xb0100000-0xb0103fff irq 5 at device 7.1 on pci6
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:e0:4c:71:71:ea
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:71:71:ea
fwe0: Ethernet address: 02:00:4c:71:71:ea
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem 0xb0104800-0xb01048ff
irq 7 at device 9.0 on pci6
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:0d:5e:e2:82:49
pci0: <multimedia, audio> at device 30.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 SATA150 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18b0-0x18bf at device 31.2 on pci0
atapci0: failed to enable memory mapping!
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd3fff,0xe3000-0xe3fff on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1396509468 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 57231MB <HTS541060G9AT00 MBBOA60A> at ata0-master UDMA100
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4244N/1.00> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s4a
rl0: link state changed to UP
