After adding device_link between the IOMMU consumer and smi,
the mediatek,larb is unnecessary now.
CC: Matthias Brugger
Signed-off-by: Yong Wu
---
arch/arm/boot/dts/mt2701.dtsi | 1 -
arch/arm/boot/dts/mt7623.dtsi | 1 -
2 files changed, 2 deletions(-)
diff --git
After adding device_link between the IOMMU consumer and smi,
the mediatek,larb is unnecessary now.
CC: Matthias Brugger
Signed-off-by: Yong Wu
---
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 15 ---
1 file changed, 15 deletions(-)
diff --git
MediaTek IOMMU has already added the device_link between the consumer
and smi-larb device. If the drm device call the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
CC: CK Hu
CC: Philipp Zabel
Signed-off-by: Yong Wu
---
MediaTek IOMMU has already added device_link between the consumer
and smi-larb device. If the jpg device call the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
CC: Rick Chang
Signed-off-by: Yong Wu
---
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c | 22
MediaTek IOMMU has already added the device_link between the consumer
and smi-larb device. If the vcodec device call the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
CC: Tiffany Lin
Signed-off-by: Yong Wu
---
Normally, If the smi-larb HW need work, we should enable the smi-common
HW power and clock firstly.
This patch adds device-link between the smi-larb dev and the smi-common
dev. then If pm_runtime_get_sync(smi-larb-dev), the pm_runtime_get_sync
(smi-common-dev) will be called automatically.
Since
MediaTek IOMMU don't have its power-domain. all the consumer connect
with smi-larb, then connect with smi-common.
M4U
|
smi-common
|
-
| |...
| |
larb1 larb2
| |
vdec venc
When the consumer works, it should
After adding device_link between the consumer with the smi-larbs,
if the consumer call its owner pm_runtime_get(_sync), the
pm_runtime_get(_sync) of smi-larb and smi-common will be called
automatically. Thus, the consumer don't need the property.
And IOMMU also know which larb this consumer
The iommu consumer should use device_link to connect with the
smi-larb(supplier). then the smi-larb should run before the iommu
consumer. Here we delay the iommu driver until the smi driver is
ready, then all the iommu consumer always is after the smi driver.
When there is no this patch, if some
DL_FLAG_AUTOREMOVE_CONSUMER/SUPPLIER means "Remove the link
automatically on consumer/supplier driver unbind", that means we should
remove whole the device_link when there is no this driver no matter what
the ref_count of the link is.
CC: Greg Kroah-Hartman
Signed-off-by: Yong Wu
---
The
MediaTek IOMMU block diagram always like below:
M4U
|
smi-common
|
-
| | ...
| |
larb1 larb2
| |
vdec venc
All the consumer connect with smi-larb, then connect with smi-common.
MediaTek IOMMU don't have its
In the reboot burning test, if some Multimedia HW has something wrong,
It may keep send the invalid request to IOMMU. In order to avoid
affect the reboot flow, we add the shutdown callback to disable
M4U HW when shutdown.
Signed-off-by: Yong Wu
---
drivers/iommu/mtk_iommu.c| 6 ++
The register VLD_PA_RNG(0x118) was forgot to backup while adding 4GB
mode support for mt2712. this patch add it.
Fixes: 30e2fccf9512 ("iommu/mediatek: Enlarge the validate PA range
for 4GB mode")
Signed-off-by: Yong Wu
---
drivers/iommu/mtk_iommu.c | 2 ++
drivers/iommu/mtk_iommu.h | 1 +
2
There are 2 mmu cells in a M4U HW. we could adjust some larbs entering
mmu0 or mmu1 to balance the bandwidth via the smi-common register
SMI_BUS_SEL(0x220)(Each larb occupy 2 bits).
In mt8183, For better performance, we switch larb1/2/5/7 to enter
mmu1 while the others still keep enter mmu0.
In
This patch only move the clk_prepare_enable and config_port into the
runtime suspend/resume callback. It doesn't change the code content
and sequence.
This is a preparing patch for adjusting SMI_BUS_SEL for mt8183.
(SMI_BUS_SEL need to be restored after smi-common resume every time.)
Also it
Switch to SPDX license identifier for MediaTek iommu/smi and their
header files.
Signed-off-by: Yong Wu
Reviewed-by: Rob Herring
---
drivers/iommu/mtk_iommu.c | 10 +-
drivers/iommu/mtk_iommu.h | 10 +-
drivers/iommu/mtk_iommu_v1.c
The "mediatek,larb-id" has already been parsed in MTK IOMMU driver.
It's no need to parse it again in SMI driver. Only clean some codes.
This patch is fit for all the current mt2701, mt2712, mt7623, mt8173
and mt8183.
After this patch, the "mediatek,larb-id" only be needed for mt2712
which have 2
Normally the M4U HW connect EMI with smi. the diagram is like below:
EMI
|
M4U
|
smi-common
|
-
||| |...
larb0 larb1 larb2 larb3
Actually there are 2 mmu cells
Both mt8173 and mt8183 don't have this vld_pa_rng(valid physical address
range) register while mt2712 have. Move it into the plat_data.
Signed-off-by: Yong Wu
---
drivers/iommu/mtk_iommu.c | 3 ++-
drivers/iommu/mtk_iommu.h | 1 +
2 files changed, 3 insertions(+), 1 deletion(-)
diff --git
The larb-id may be remapped in the smi-common, this means the
larb-id reported in the mtk_iommu_isr isn't the real larb-id,
Take mt8183 as a example:
M4U
|
-
| SMI common |
The M4U IP blocks in mt8183 is MediaTek's generation2 M4U which use
the ARM Short-descriptor like mt8173, and most of the HW registers
are the same.
Here list main differences between mt8183 and mt8173/mt2712:
1) mt8183 has only one M4U HW like mt8173 while mt2712 has two.
2) mt8183 don't have
In some SoCs like mt8183, SMI add GALS(Global Async Local Sync) module
which can help synchronize for the modules in different clock frequency.
It can be seen as a "asynchronous fifo". This is a example diagram:
M4U
|
--
||
gals0-rx
In mt8173 and mt8183, 0x48 is REG_MMU_STANDARD_AXI_MODE while
it is extended to REG_MMU_CTRL which contains _STANDARD_AXI_MODE in
the other SoCs. I move this property to plat_data since both mt8173
and mt8183 use this property.
It is a preparing patch for mt8183.
Signed-off-by: Yong Wu
---
In some SoCs, M4U doesn't have its "bclk", it will use the EMI
clock instead which has always been enabled when entering kernel.
This also is a preparing patch for mt8183.
Signed-off-by: Yong Wu
---
drivers/iommu/mtk_iommu.c | 10 +++---
drivers/iommu/mtk_iommu.h | 3 +++
2 files changed,
Use a struct as the platform special data instead of the enumeration.
Also there is a minor change that moving the position of
"enum mtk_smi_gen" definition, this is because we expect define
"struct mtk_smi_common_plat" before it is referred.
This is a preparing patch for mt8183.
Signed-off-by:
MediaTek extend the arm v7s descriptor to support the dram over 4GB.
In the mt2712 and mt8173, it's called "4GB mode", the physical address
is from 0x4000_ to 0x1_3fff_, but from EMI point of view, it
is remapped to high address from 0x1__ to 0x1__, the
bit32 is always
Add two helper functions: paddr_to_iopte and iopte_to_paddr.
Signed-off-by: Yong Wu
Reviewed-by: Robin Murphy
---
drivers/iommu/io-pgtable-arm-v7s.c | 45 --
1 file changed, 33 insertions(+), 12 deletions(-)
diff --git a/drivers/iommu/io-pgtable-arm-v7s.c
The config_port of mt2712 and mt8183 are the same. Use a general
config_port interface instead.
In addition, in mt2712, larb8 and larb9 are the bdpsys larbs which
are not the normal larb, their register space are different from the
normal one. thus, we can not call the general config_port. In
This patch adds decriptions for mt8183 IOMMU and SMI.
mt8183 has only one M4U like mt8173 and is also MTK IOMMU gen2 which
uses ARM Short-Descriptor translation table format.
The mt8183 M4U-SMI HW diagram is as below:
EMI
|
This patchset mainly adds support for mt8183 IOMMU and SMI.
mt8183 has only one M4U like mt8173 and is also MTK IOMMU gen2 which
uses ARM Short-Descriptor translation table format.
The mt8183 M4U-SMI HW diagram is as below:
EMI
|
Hi Linus,
there is a small merge conflict this time in arch/powerpc/kernel/iommu.c
with the tag I send you. I did a test-merge with your latest tree
locally to include my resolution in this email, but for some reason git
shows me a conflict in another file (drivers/iommu/amd_iommu.c) in the
31 matches
Mail list logo
