On Mon, Nov 18, 2013 at 10:08 PM, Lorenzo Marcantonio
l.marcanto...@logossrl.com wrote:
On Mon, Nov 18, 2013 at 09:19:02PM +0100, Tomasz Wlostowski wrote:
Why don't you write a one A4-page long blueprint, discuss it on the list,
and if your time permits, code the thing?
It was discussed a
Carl,
In you last fp-lib-table work, I discovered mismatch in filename vs. lib_path.
Only one lib_path had a typo.
See attached patch.
You can test the entire fp-lib-table by doing the following in pcnbew:
Toolbar(Add Modules) - Mouse Click to drop new module - Select List All.
This will
I have just committed the work.
FYI, I merged two libraries IIRC, something like smd_resistors and
Resistor_SMD_RevA and another one.
I was about to send the fp-lib-table, but I'll double-check it using the
hint you just gave me. BRB
Carl
On Mon, Nov 18, 2013 at 11:13 PM, Dick Hollenbeck
fp-lib-table is attached. I also just committed minor corrections. Somehow
a bzr move --auto didn't work and I had to do it manually.
As a general rule of thumb, the naming goes in this order:
1. Part type (resistor, cap, etc), must be in plural form
2. Package type (SOIC, SMD, etc)
3.
Le 15/11/2013 17:06, Dick Hollenbeck a écrit :
eeschema, today:
When you import the hierarchical pin from a nested sheet, you get a free,
stray
hierarchical label up at
y = 0
as well as in the pinsheet box.
It goes away after placement.
Fix committed.
--
Jean-Pierre CHARRAS
Hi,
Is it intentional to not be able to cancel the library dialog using the ESC
key on the keyboard? I am aware of some bugs in wxWidgets such as
thishttp://trac.wxwidgets.org/ticket/12952.
May it be the reason why we can't? I think it would be nice if we could
have a consistent behavior between
18/11/13 22:19, Tomasz Wlostowski kirjoitti:
On 11/18/2013 07:11 PM, Lorenzo Marcantonio wrote:
ATM the thing still I mostly miss are inter-class design rules (i.e.
having 220VAC and 5VDC on the same board).
Why don't you write a one A4-page long blueprint, discuss it on the
list, and if
Fantastic Carl!
fp-lib-table is attached. I also just committed minor corrections. Somehow a
bzr move
--auto didn't work and I had to do it manually.
As a general rule of thumb, the naming goes in this order:
1. Part type (resistor, cap, etc), must be in plural form
2. Package type
On 11/19/2013 11:20 AM, Carl Poirier wrote:
Hi,
Is it intentional to not be able to cancel the library dialog using the ESC
key on the
keyboard? I am aware of some bugs in wxWidgets such as this
http://trac.wxwidgets.org/ticket/12952. May it be the reason why we can't?
I think it
would
Yes that is I believe the behavior users would expect. (double-ESC if cell
editor is active)
Thanks for the clarification.
Carl
On Tue, Nov 19, 2013 at 12:58 PM, Dick Hollenbeck d...@softplc.com wrote:
On 11/19/2013 11:20 AM, Carl Poirier wrote:
Hi,
Is it intentional to not be able to
Sounds good to me. I'll look into adding some descriptions later on.
Anyway, it will not be a disruptive change...
On Tue, Nov 19, 2013 at 12:55 PM, Dick Hollenbeck d...@softplc.com wrote:
Fantastic Carl!
fp-lib-table is attached. I also just committed minor corrections.
Somehow a bzr
On 11/18/2013 2:46 AM, Lorenzo Marcantonio wrote:
In the target properties dialog: aren't size and thickness swapped?
I just took a look at the Target Properties dialog and it looks
correct to me. The Size property changes the diameter of the target
and the Thickness property changes the
On 11/19/2013 12:03 PM, Carl Poirier wrote:
Yes that is I believe the behavior users would expect. (double-ESC if cell
editor is active)
Thanks for the clarification.
Carl
Its another wx 2.8 specific issue.
On wx 2.9/3.0, the ESC key cancels the dialog, regardless of the status of the
On Tue, Nov 19, 2013 at 02:48:07PM -0500, Wayne Stambaugh wrote:
I just took a look at the Target Properties dialog and it looks
correct to me. The Size property changes the diameter of the target
and the Thickness property changes the line width of the target.
Uhmmm... I draw a target. In
On Tue, Nov 19, 2013 at 02:43:38PM -0600, Dick Hollenbeck wrote:
I am running into about 2 of these wx 2.8 vs. 2.9/3.0 issues per day now.
And don't forget the differences between wx/Linux and wx/Windows!
Anyway, be glad... think about what happened from Qt3 to Qt4...
I'm glad I stuck with
On 11/19/2013 12:05 PM, Carl Poirier wrote:
Sounds good to me. I'll look into adding some descriptions later on. Anyway,
it will not
be a disruptive change...
Agreed, no hurry at all.
Maybe the Description will irk some people into realizing that the libraries
are not
They way you
Testing library view in CvPCb.
Latest bzr.
EuroBoard_Outline
View Selected Footprint window active.
I have the 3D viewer open. (error does not happen when 3D is closed)
Select:
EuroBoard_Outline:EuroBoard160mmX100mm or
EuroBoard_Outline:EuroBoard160mmX100mm_holes
happens also with
Le 19/11/2013 20:48, Wayne Stambaugh a écrit :
On 11/18/2013 2:46 AM, Lorenzo Marcantonio wrote:
In the target properties dialog: aren't size and thickness swapped?
I just took a look at the Target Properties dialog and it looks
correct to me. The Size property changes the diameter of the
18 matches
Mail list logo
