Hi Everyone,
Just a update on my project. Last Friday the UPS Lady carried a long box up to
the front door,I ordered a 60" x 68" pitch from Ed Sterba, after she handed it
over I seen a hole punched through the 1/4 plywood.I thought this can't be,she
was nice enough to stay lone enough
Hi Everyone,
Just a update on my project. Last Friday the UPS Lady carried a long box up to
the front door,I ordered a 60" x 68" pitch from Ed Sterba, after she handed it
over I seen a hole punched through the 1/4 plywood.I thought this can't be,she
was nice enough to stay lone enough
ke 4" off the tip. It took 4 months, several rounds of
appeals, and a see you in court notice with Fed Ex Ground before they finally
paid for it. Glad yours wasn't damaged.
-Jeff Scott
----- Original Message -
From: rkp...@comcast.net
Sent: 01/04/12 03:42 PM
To: krnet
Subject:
Hi everyone
Anyone out there have a nose gear assembly they would to sell? If so please
let me know. I am getting ready to order one,but I thought I would check with
everyone first.
Robert Pesak
Hermitage, Tn.
Hi everyone,
I would like to build my own nose gear assembly. The question I have is, What
would be a safe tube and wall dimension . I have seen some great looking home
made nose gear but didn't look to see what kine of material was used.
Robert K. Pesak
Hermitage,Tn.
Hi everyone
Can any of you guys using a O-200 remember what your weight on the nose wheel
was?
Robert Pesak
Hermitage,Tn.
Hi Mike
I personally think covering all wood surface should be covered with with deck
cloth , this will keep small cracks from showing up later on.
Hi everyone,
I looking through some of the old gatherings,I happened on a picture that
was taken in Red Oak, Ia. The KR I noticed was owned by a fellow by the name
of Steve Alderman.The caption under the picture mentioned the cowling was made
for a O-200 by Dan Deihl. Is there anyone
Hi everyone
I received my prop hub extension from Saber Inc., it looks great. I couldn't
wait to see how it looked on the front of the 0-200. It seem to be a very tight
fit over the prop hub on the engine, it would only go about 1/4" and stop.
Would I have to first heat the prop hub
Hi Everyone,
I just got home from a place called Hazel green Al. It's one hundred
fourteen miles from my home in Hermitage, Tn. I had a great time visiting with
everyone at Mark's airport, as I watched them build a deck onto the new club
house. I hope it wont be to much longer before I
Hi everyone
I sent the link for my pictures,but I'm not sure that it came out right. I
think this will work.
Robert Pesak
Hermitage, Tn.
http :// photobucket .com/ robertskrs
All the hardware in question was hand made using a metal cutting band saw to
cut the steel. or a regular wood cutting miter saw with a 60 tooth carbide
blade to cut the 6061-T6. All the steel was welded using aTIG welder.Nothing
real high tech in my shop. One other thing I didn't mention,
Hi All,
I will be in Oshkosh Sunday morning,hopefully will be staying in the private
campgrounds across from the ultralight parking. See ya there.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone,
Anyone out there know of a good supplier of stainless steel exhaust pipe?
Robert Pesak
Hermitage, Tn.
Hi Everyone,
A fellow at muhlenberge County Airport in Greenville Ky, has a kr that is
well on it's way. I personally have seen it,and the workmanship looks pretty
good.I just got off the phone with him and he asked if I would let everyone
that he would bring it to the gathering
Hi Everyone,
I hope everyone is having a great labor day week end. The UPS man delivered
a package on Friday, and it was just the thing to keep me busy this weekend. I
ordered my trim servo and grips from Ray Allen on Monday and they delivered on
Friday,great company!!! http ://
Hi Everyone,
I haven't heard anything about the camping area,I'll be up with my camper
Friday afternoon.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone,
The question I have is,Where is the best location for the pitot static port?
I do understand that it will make a deference because every kr is not shaped
the same,but just a general location would with the plumbing.
Robert Pesak
Hermitage, Tn.
Hi Everyone,
I'm not sure where I seen the pictures of two cables from the aft of the
fuselage for the seat belts. If anyone has the link for that setup,please send
it.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone
Just a little progress report on my project. I'm getting ready install the
aft deck.I spent a week finishing all the wiring for nav.lights,strobe
light,and the trim servo.This week end I installed the comm.antenna,xponder
antenna and the static vents.
Robert Pesak
I personally am using using the west system. One of the things to remember is,
when mixing micro balloons, the more micro balloons the easier to sand and it
will weigh less.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
- Original Message -
From: "rick newton"
Dan , the last I bought some venal ester it was from a boat builder we had in
Nashville. I brought my own gallon containers and he filled them from a 55
gallon drum.I don't remember what he charged, but it wasn't much .
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone,
I have also started to wire my panel,I think it's relaxing.
Robert Pesak
Hermitage,Tn.
http://photobucket.com/robertskrs
Hi Every one
A friend of mine was traveling south on I-65 last night around Huntsville
Al., He told me your not going to belive this, but there is a KR sitting along
the side of the interstate.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi All,
I'm getting ready to place a order,The question I have is concerning the gauge
of wiring for my ignition switch.The switch that I got calls for shielded
wire,but doesn't say anything the gauge. Thanks for all the help.
Robert Pesak
Hermitage, Tn.
Hi Everyone,
The question I have is in regards to the oil temperature senders. I need the
reducer for the sending unit. Anyone know where I can get one? The one Wicks
sells is with the sender for a Mitchell oil temp gauge, not sure if it will
work on my ISS gauge. Any help will be
Hi Everyone,
I can remember the first part I built for my KR-2S,it was December 2005. The
first part I built, was a one piece main spar. It doesn't seem like five years
ago.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone,
I have a question on hooking up my CHT sensor and my EGT sensor. The leads on
the sensors are only about 12" long. Do I need to use the same type of wire or
can I use
any wire for the extensions to reach the gauge? As always, thanks for the help.
Robert Pesak
Hermitage,
Dan,
What thickness was the material you use on your fuel tanks? I'm thinking
about building my header tank.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone,
I haven't had much time to update my photobucket. I'm trying to finish my
panel I painted it and started to install the instruments for the final time. I
took some pictures this afternoon and uploaded them. Hope to see you all in
Oshkosh next month.
Robert Pesak
Hermitage,
Michael,
I built fuel tank in the leading edge of my wings. Each one holds right at
nine gallons, ther are pictures on my photo bucket.
Robert Pesak
Hermitage, Tn.
http://photobucket.com/robertskrs
Hi Everyone,
Anyone know where I can buy prop bolts 51/4 inch long prop bolts? I looked on
the ACS site but longest one I seen was around four inches long.Measuring the
thickness of the prop, crush plate and the forward and aft bulkhead, I need
about 5 1/4 inch bolt. Any help would be
Hi Everyone,
I hope everyone is is well, I took some time to update my PotoBucket . One of
the things I changed was the finish on my panel,at first I painted with a
hammered gray finish,it wasn't long before I realized it was very fragile and
would chip easily.After taking every apart and
Try this link it may work better.
Robert Pesak
http://photobucket.com/robertskrs
34 matches
Mail list logo