Re: Just found this on You Tube! ((Bill's newest video))

2022-10-08 Thread Tim Ziegler 
For sure Bill.
Kind Regards,

Timothy J. Ziegler
Ziegler WoodWork & Specialty
14171 160th Ave.
Foreston MN 56330

320-294-5798 shop
320-630-2243 cell


On Sat, Oct 8, 2022 at 4:41 PM  wrote:

> Yea pressure pots and epoxy and all the rest yes very expensive
>
> But sometimes something as simple as watered down pva glue soaked into the
> wood
>
> Can help done just before the final 1/32 deep finishing cut can do it
>
> Oils for timber are very good soke the wood overnight in it then mill that
> last cut
>
> But the down side is you can’t apply a finish to the timber all you can do
>
> Is buff it with like the beal buffing system. I did a lot of experimenting
>
> In this also speeds and feeds help too very slow router speed and a very
> slow feed rate
>
> On that last cut all these things can help with tear out. But some woods
> no
>
> Matter what you do tear I just don’t use them.
>
>
>
> Bill
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com <
> legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Tim Ziegler
> *Sent:* Saturday, 8 October 2022 9:38 PM
> *To:* legacy-ornamental-mills@googlegroups.com
> *Subject:* Re: Just found this on You Tube! ((Bill's newest video))
>
>
>
> That stuff costs an arm and a leg though. I looked into it when it was a
> topic of discussion a few months back.
>
> You really can tie up some serious money on it.
>
>
> Kind Regards,
>
>
>
> Timothy J. Ziegler
>
> Ziegler WoodWork & Specialty
>
> 14171 160th Ave.
>
> Foreston MN 56330
>
>
>
> 320-294-5798 shop
>
> 320-630-2243 cell
>
>
>
>
>
> On Fri, Oct 7, 2022 at 11:31 PM 'Curt George' via Legacy Ornamental Mills <
> legacy-ornamental-mills@googlegroups.com> wrote:
>
> Hey Bill
>
>
>
> I like your videos. Thank you.
>
>
>
> One suggestion on your Pine WOOD tare-out problem. Can you seal the wood
> first to make it harder?
>
> Perhaps something like Cactus juice and a vacuum chamber or pressure pot?
> or some kind of resin to harden the wood before turning?
>
>
>
> C.A.G.
>
>
>
> On Friday, October 7, 2022 at 11:07:38 AM EDT, 
> wrote:
>
>
>
>
>
> Very crappy pine wood I used on these 2 videos the router bit tore the
> wood but I didn’t make these to look at
>
> It’s to learn from, if I was doing to too keep it I would use a nice
> hardwood that is not prone to tearing
>
> As much
>
>
>
> Bill
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com <
> legacy-ornamental-mills@googlegroups.com> *On Behalf Of *
> bulke...@mmnet.com.au
> *Sent:* Saturday, 8 October 2022 1:52 AM
> *To:* legacy-ornamental-mills@googlegroups.com
> *Subject:* RE: Just found this on You Tube! ((Bill's newest video))
>
>
>
> Wow that was quick thank you I just posted it, check out the other one a
> Dimond pattern
>
> Made from that 3 start rope
>
>
>
> Bill
>
>
>
>
>
> *From:* 'Curt George' via Legacy Ornamental Mills <
> legacy-ornamental-mills@googlegroups.com>
> *Sent:* Saturday, 8 October 2022 12:16 AM
> *To:* Legacy ornamental mills 
> *Subject:* Just found this on You Tube! ((Bill's newest video))
>
>
>
> https://www.youtube.com/watch?v=S4b-j9ZCE5E
>
>
>
> I like it Bill!
>
>
>
> Thank you.
>
>
>
> C.A.G.
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com?utm_medium=email&utm_source=footer>
> .
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
> .
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legac

RE: Just found this on You Tube! ((Bill's newest video))

2022-10-08 Thread bulkeley 
Yea pressure pots and epoxy and all the rest yes very expensive 

But sometimes something as simple as watered down pva glue soaked into the wood 

Can help done just before the final 1/32 deep finishing cut can do it

Oils for timber are very good soke the wood overnight in it then mill that last 
cut

But the down side is you can’t apply a finish to the timber all you can do 

Is buff it with like the beal buffing system. I did a lot of experimenting

In this also speeds and feeds help too very slow router speed and a very slow 
feed rate

On that last cut all these things can help with tear out. But some woods no 

Matter what you do tear I just don’t use them.

 

Bill

 

From: legacy-ornamental-mills@googlegroups.com 
 On Behalf Of Tim Ziegler
Sent: Saturday, 8 October 2022 9:38 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Just found this on You Tube! ((Bill's newest video))

 

That stuff costs an arm and a leg though. I looked into it when it was a topic 
of discussion a few months back.

You really can tie up some serious money on it.




Kind Regards,

 

Timothy J. Ziegler

Ziegler WoodWork & Specialty

14171 160th Ave.

Foreston MN 56330

 

320-294-5798 shop

320-630-2243 cell

 

 

On Fri, Oct 7, 2022 at 11:31 PM 'Curt George' via Legacy Ornamental Mills 
mailto:legacy-ornamental-mills@googlegroups.com> > wrote:

Hey Bill

 

I like your videos. Thank you.

 

One suggestion on your Pine WOOD tare-out problem. Can you seal the wood first 
to make it harder?

Perhaps something like Cactus juice and a vacuum chamber or pressure pot? or 
some kind of resin to harden the wood before turning?

 

C.A.G.

 

On Friday, October 7, 2022 at 11:07:38 AM EDT, mailto:bulke...@mmnet.com.au> > wrote: 

 

 

Very crappy pine wood I used on these 2 videos the router bit tore the wood but 
I didn’t make these to look at

It’s to learn from, if I was doing to too keep it I would use a nice hardwood 
that is not prone to tearing

As much 

 

Bill 

 

From: legacy-ornamental-mills@googlegroups.com 
<mailto:legacy-ornamental-mills@googlegroups.com>  
mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of 
bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> 
Sent: Saturday, 8 October 2022 1:52 AM
To: legacy-ornamental-mills@googlegroups.com 
<mailto:legacy-ornamental-mills@googlegroups.com> 
Subject: RE: Just found this on You Tube! ((Bill's newest video))

 

Wow that was quick thank you I just posted it, check out the other one a Dimond 
pattern

Made from that 3 start rope

 

Bill

 

 

From: 'Curt George' via Legacy Ornamental Mills 
mailto:legacy-ornamental-mills@googlegroups.com> > 
Sent: Saturday, 8 October 2022 12:16 AM
To: Legacy ornamental mills mailto:legacy-ornamental-mills@googlegroups.com> >
Subject: Just found this on You Tube! ((Bill's newest video))

 

https://www.youtube.com/watch?v=S4b-j9ZCE5E  

 

I like it Bill!

 

Thank you.

 

C.A.G.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because

Re: Just found this on You Tube! ((Bill's newest video))

2022-10-08 Thread Tim Ziegler 
That stuff costs an arm and a leg though. I looked into it when it was a
topic of discussion a few months back.
You really can tie up some serious money on it.

Kind Regards,

Timothy J. Ziegler
Ziegler WoodWork & Specialty
14171 160th Ave.
Foreston MN 56330

320-294-5798 shop
320-630-2243 cell


On Fri, Oct 7, 2022 at 11:31 PM 'Curt George' via Legacy Ornamental Mills <
legacy-ornamental-mills@googlegroups.com> wrote:

> Hey Bill
>
> I like your videos. Thank you.
>
> One suggestion on your Pine WOOD tare-out problem. Can you seal the wood
> first to make it harder?
> Perhaps something like Cactus juice and a vacuum chamber or pressure pot?
> or some kind of resin to harden the wood before turning?
>
> C.A.G.
>
> On Friday, October 7, 2022 at 11:07:38 AM EDT, 
> wrote:
>
>
> Very crappy pine wood I used on these 2 videos the router bit tore the
> wood but I didn’t make these to look at
>
> It’s to learn from, if I was doing to too keep it I would use a nice
> hardwood that is not prone to tearing
>
> As much
>
>
>
> Bill
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com <
> legacy-ornamental-mills@googlegroups.com> *On Behalf Of *
> bulke...@mmnet.com.au
> *Sent:* Saturday, 8 October 2022 1:52 AM
> *To:* legacy-ornamental-mills@googlegroups.com
> *Subject:* RE: Just found this on You Tube! ((Bill's newest video))
>
>
>
> Wow that was quick thank you I just posted it, check out the other one a
> Dimond pattern
>
> Made from that 3 start rope
>
>
>
> Bill
>
>
>
>
>
> *From:* 'Curt George' via Legacy Ornamental Mills <
> legacy-ornamental-mills@googlegroups.com>
> *Sent:* Saturday, 8 October 2022 12:16 AM
> *To:* Legacy ornamental mills 
> *Subject:* Just found this on You Tube! ((Bill's newest video))
>
>
>
> https://www.youtube.com/watch?v=S4b-j9ZCE5E
>
>
>
> I like it Bill!
>
>
>
> Thank you.
>
>
>
> C.A.G.
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com?utm_medium=email&utm_source=footer>
> .
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
> .
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
> .
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/1818723068.3508189.1665203456092%40mail.yahoo.com
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/1818723068.3508189.1665203456092%40mail.yahoo.com?utm_medium=email&utm_source=footer>
> .
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEcxfMG_EFSgh37FgBNdHfdEzuLcNww_7TiFNgoi02p3A%40mail.gmail.com.

RE: Just found this on You Tube! ((Bill's newest video))

2022-10-08 Thread bulkeley 
Oh yes I can paint them with oils or thin glues  before the last cut to make it

Less likely to tear but that would make the job take much longer

And as I said these are not projects they are training

 

Bill

 

From: 'Curt George' via Legacy Ornamental Mills 
 
Sent: Saturday, 8 October 2022 3:31 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Just found this on You Tube! ((Bill's newest video))

 

Hey Bill

 

I like your videos. Thank you.

 

One suggestion on your Pine WOOD tare-out problem. Can you seal the wood first 
to make it harder?

Perhaps something like Cactus juice and a vacuum chamber or pressure pot? or 
some kind of resin to harden the wood before turning?

 

C.A.G.

 

On Friday, October 7, 2022 at 11:07:38 AM EDT, mailto:bulke...@mmnet.com.au> > wrote: 

 

 

Very crappy pine wood I used on these 2 videos the router bit tore the wood but 
I didn’t make these to look at

It’s to learn from, if I was doing to too keep it I would use a nice hardwood 
that is not prone to tearing

As much 

 

Bill 

 

From: legacy-ornamental-mills@googlegroups.com 
<mailto:legacy-ornamental-mills@googlegroups.com>  
mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of 
bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> 
Sent: Saturday, 8 October 2022 1:52 AM
To: legacy-ornamental-mills@googlegroups.com 
<mailto:legacy-ornamental-mills@googlegroups.com> 
Subject: RE: Just found this on You Tube! ((Bill's newest video))

 

Wow that was quick thank you I just posted it, check out the other one a Dimond 
pattern

Made from that 3 start rope

 

Bill

 

 

From: 'Curt George' via Legacy Ornamental Mills 
mailto:legacy-ornamental-mills@googlegroups.com> > 
Sent: Saturday, 8 October 2022 12:16 AM
To: Legacy ornamental mills mailto:legacy-ornamental-mills@googlegroups.com> >
Subject: Just found this on You Tube! ((Bill's newest video))

 

https://www.youtube.com/watch?v=S4b-j9ZCE5E  

 

I like it Bill!

 

Thank you.

 

C.A.G.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/1818723068.3508189.1665203456092%40mail.yahoo.com
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/1818723068.3508189.1665203456092%40mail.yahoo.com?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/000e01d8dae9%240dd3f760%24297be620%24%40mmnet.com.au.

Re: Just found this on You Tube! ((Bill's newest video))

2022-10-07 Thread 'Curt George' via Legacy Ornamental Mills 
 Hey Bill
I like your videos. Thank you.
One suggestion on your Pine WOOD tare-out problem. Can you seal the wood first 
to make it harder?Perhaps something like Cactus juice and a vacuum chamber or 
pressure pot? or some kind of resin to harden the wood before turning?
C.A.G.
On Friday, October 7, 2022 at 11:07:38 AM EDT,  
wrote:  
 
 
Very crappy pine wood I used on these 2 videos the router bit tore the wood but 
I didn’t make these to look at

It’s to learn from, if I was doing to too keep it I would use a nice hardwood 
that is not prone to tearing

As much 

  

Bill 

  

From: legacy-ornamental-mills@googlegroups.com 
 On Behalf Of bulke...@mmnet.com.au
Sent: Saturday, 8 October 2022 1:52 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: Just found this on You Tube! ((Bill's newest video))

  

Wow that was quick thank you I just posted it, check out the other one a Dimond 
pattern

Made from that 3 start rope

  

Bill

  

  

From: 'Curt George' via Legacy Ornamental Mills 
 
Sent: Saturday, 8 October 2022 12:16 AM
To: Legacy ornamental mills 
Subject: Just found this on You Tube! ((Bill's newest video))

  

https://www.youtube.com/watch?v=S4b-j9ZCE5E  

  

I like it Bill!

  

Thank you.

  

C.A.G.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au.


-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au.
  

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/1818723068.3508189.1665203456092%40mail.yahoo.com.

RE: Just found this on You Tube! ((Bill's newest video))

2022-10-07 Thread bulkeley 
Very crappy pine wood I used on these 2 videos the router bit tore the wood but 
I didn’t make these to look at

It’s to learn from, if I was doing to too keep it I would use a nice hardwood 
that is not prone to tearing

As much 

 

Bill 

 

From: legacy-ornamental-mills@googlegroups.com 
 On Behalf Of bulke...@mmnet.com.au
Sent: Saturday, 8 October 2022 1:52 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: Just found this on You Tube! ((Bill's newest video))

 

Wow that was quick thank you I just posted it, check out the other one a Dimond 
pattern

Made from that 3 start rope

 

Bill

 

 

From: 'Curt George' via Legacy Ornamental Mills 
mailto:legacy-ornamental-mills@googlegroups.com> > 
Sent: Saturday, 8 October 2022 12:16 AM
To: Legacy ornamental mills mailto:legacy-ornamental-mills@googlegroups.com> >
Subject: Just found this on You Tube! ((Bill's newest video))

 

https://www.youtube.com/watch?v=S4b-j9ZCE5E  

 

I like it Bill!

 

Thank you.

 

C.A.G.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
<mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au
 
<https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au?utm_medium=email&utm_source=footer>
 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/002201d8da5e%2482978a20%2487c69e60%24%40mmnet.com.au.

RE: Just found this on You Tube! ((Bill's newest video))

2022-10-07 Thread bulkeley 
Wow that was quick thank you I just posted it, check out the other one a Dimond 
pattern

Made from that 3 start rope

 

Bill

 

 

From: 'Curt George' via Legacy Ornamental Mills 
 
Sent: Saturday, 8 October 2022 12:16 AM
To: Legacy ornamental mills 
Subject: Just found this on You Tube! ((Bill's newest video))

 

https://www.youtube.com/watch?v=S4b-j9ZCE5E  

 

I like it Bill!

 

Thank you.

 

C.A.G.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com 
 .
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/465685326.3323209.1665148561808%40mail.yahoo.com
 

 .

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d8da5c%24713cdc50%2453b694f0%24%40mmnet.com.au.

Re: Just found this... ;-)

2018-02-12 Thread Tim Krause 
To clarify, the picture in the ad, the vertical four corner supports to the 
upper rail uses rectangle stock and cam clamps.  The majority of the woodchucks 
I've seen have what appear to be 1" round still stock to hold the upper rails.  
That is the version you have Richard.

⁣Sent from BlueMail ​

On Feb 12, 2018, 12:59 AM, at 12:59 AM, Richard Ellis  
wrote:
>My Woodchuck rails and legs are all rectangle in shape ,same size. But
>the 
>two top rails are of thicker section material .
>Richard
>
>On Sunday, February 11, 2018 at 9:42:33 PM UTC, Tim wrote:
>>
>> This machine is really early in legacy's history.  Take note of the 
>> rectangle steel legs instead of the round.  There is also no mention
>of the 
>> IRT name designation which the picture appears to be.  Please refer
>to the 
>> hidden history page. http://ornamentalmills.com/history/ .
>>
>> Tim
>>
>> Sent from BlueMail  
>> On Feb 10, 2018, at 4:34 PM, 'Curt George' via Legacy Ornamental
>Mills <
>> legacy-orna...@googlegroups.com > wrote:
>>>
>>> Sep/Oct 1992 Fine Woodworking. 
>>>
>>> C.A.G. 
>>>
>>>
>>> On Saturday, February 10, 2018 7:30 PM, 'Curt George' via Legacy 
>>> Ornamental Mills >
>wrote:
>>>
>>>
>>> [image: Inline image] 
>>> C.A.G. 
>>> -- 
>>> You received this message because you are subscribed to the Google
>Groups 
>>> "Legacy Ornamental Mills" group. 
>>> To unsubscribe from this group and stop receiving emails from it,
>send an 
>>> email to legacy-ornamental-mills+unsubscr...@googlegroups.com 
>>> . 
>>> To post to this group, send email to legacy-orna...@googlegroups.com
>
>>> . 
>>> Visit this group at 
>>> https://groups.google.com/group/legacy-ornamental-mills. 
>>> For more options, visit https://groups.google.com/d/optout. 
>>>
>>>
>>> -- 
>>> You received this message because you are subscribed to the Google
>Groups 
>>> "Legacy Ornamental Mills" group. 
>>> To unsubscribe from this group and stop receiving emails from it,
>send an 
>>> email to legacy-ornamental-mills+unsubscr...@googlegroups.com 
>>> . 
>>> To post to this group, send email to legacy-orna...@googlegroups.com
>
>>> . 
>>> Visit this group at 
>>> https://groups.google.com/group/legacy-ornamental-mills. 
>>> For more options, visit https://groups.google.com/d/optout. 
>>>
>>
>
>-- 
>You received this message because you are subscribed to the Google
>Groups "Legacy Ornamental Mills" group.
>To unsubscribe from this group and stop receiving emails from it, send
>an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
>To post to this group, send email to
>legacy-ornamental-mills@googlegroups.com.
>Visit this group at
>https://groups.google.com/group/legacy-ornamental-mills.
>For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this... ;-)

2018-02-12 Thread 'Curt George' via Legacy Ornamental Mills 
Good morning  Richard
The ad post, is an older version of the Woodchuck then what you own. The IRT 
was a kit that you could buy and make your own machine.
Here is the history page.C.A.G.
History Of Phantom Engineering/ Legacy Ornamental Mill

History in a Nut Shell
>From Tracy Anderson in 2010:Here’s the history of Legacy’s Ornamental Mills in 
>a nut shell. 1990 Phantom Engineering built and offered the Woodchuck model 
>IRT33 (33” Indexing Router Table). It was made out of steel and had two flat 
>tables on top with a gap between them for the router bit to extend through. It 
>had a headstock and tailstock on an adjustable bed and an indexing head.Later 
>that year we designed a kit that you could build that was designed around the 
>Woodchuck. The kit included the steel headstock and a couple of other 
>components but everything else was made of wood based on the plans and 
>templates included in the kit. It did not have any leadscrews to drive or 
>position the router or any gears to cut spirals.In 1991 we introduced the MA 
>series Ornamental Mill that had a carriage for the router, leadscrews and 
>gears and the adjustable bed. Still called the Woodchuck, the MA series was 
>available in 4 difference sizes and lengths. Later we started Legacy 
>Woodworking Machinery and introduced the Legacy Series and two updates later 
>we have the Legacy model 900 and 1200.From Andy on the origins of "Ornamental 
>Mill" and "Ornamental Milling":"We created the terms in the early days and 
>stuck with it. "In the Ornamental Milling News volume 2 issue 4 it was written 
>"In June of 1996 Phantom Engineering introduced their new and improved 
>Ornamental Mill, the Legacy".Legacy has a long history of various machines. I 
>will attempt to put together an illustrated time line of all of the machines 
>that have come and gone. Many of the photos have been saved from Legacy's web 
>site over the years. Their web presence started approximately in 1998. All 
>dates are approximates.
| Model | Image | Year | Notes |
| Woodchuck IRT-33 |  | 1990 | The first machine produced by Phantom 
Engineering. Released as the Woodchuck Indexing Router Table. Also known as the 
IRT and also Woodchuck Router System.   
   - 33" length by 7" diameter turning capacity.
   - 13.25 degrees of taper.
   - 16 and 24 position index plates included.
Optional Accessories:   
   - Increase length to 80 inches.
   - Left and right spiral capabilities for 3,4,5,6, and 7-1/2" pitch.
  |
| Woodchuck/ IRT-KIT |  | 1990 | This was designed as a DIY kit. The kit came 
with a plan set that allowed you to build the Woodchuck from wood. Included in 
the kit was an indexable headstock, 24 position index plate ,Auto Indexing hubs 
and an operation video.Recommended length was 33".Optional Accessories:   
   - Index plates, 16,20, 32 positions.
   - Spiral attachment similar to the IRT-33 with updated plans.
 |
| Woodchuck MA |  | 1991 | All Steel Construction , Template follower feature 
added, tilting bed, Y axis with screw, multiple geared motors for independent 
drive of the spindle and x-axis leadscrew, 19 pitches. |
| 500 |  | 1997 | Steel RailsAcrylic Gears providing 1/3", 1", 2", 3" and 6".no 
taperOptions included a "Lathe Drive Package". This consisted of a gear set 
capable of creating a 1/32" pitch to be able to use the legacy as a copy lathe. 
The owner built a, "Template Support Holder."  |
| 600 | No Image Available, referenced on an early version of Legacy's Web 
site. | ? | Steel Rails, no taper |
| 1000 and 1000L | See model 1500 below | 1997 |
   - Steel Rails
   - 5 pitches
   - 60" length turning capacity
 |
| 1500 and 1500L |  | 1997 | Same as 1500 but included all optional accessories 
available at the time.   
   - Linear Drive
   - Elevation lift
   - Floor Stand
   - 20 total gear pitches
 |
| 500 |  | 2000 | This is a model 500 according to the name plate on the 
machine. The owner is selling it as a Model 500 EXS. It's believed to have the 
same pitch capabilities as the earlier steel rail version but no information is 
available. The machine was offered for sale on Ebay in Nov 2012. |
| 600EXL |  | 2000-2002 | Introduction of Aluminum rails. No y-axis screw. 
Single direction spirals.   
   - 2" thick by 8" wide flat stock
   - 5 1/2" dia. by 40" round stock capacity
   - Spiral Pitches: 1/2", 1", 2", 3", 6" and .33" per rotation
   - #2MT headstock with 1" -8 tpi threads will utilize most standard lathe 
accessories
   - Precision machined, laser cut and stamped steel construction, Acrylic 
gears.
   - 24" X 48" bench space required
  |
| 1000EXL |  | 2000-2004 |
   - 3.5" thick by 14" wide flat stock capacity
   - 10" dia. by 60" round stock capacity
   - Spiral Pitches: 2", 3", 4", 4 1/2", 5", 6", and 7 1/2" per rotation
   - Maximum taper angle: 2.5 degrees or 5.25" at 60"
   - #2MT Headstock and Tailstock
   - Index Drive Center (Headstock)
   - Live Center (Tailstock)
   - Quick release tailstock
   - Precision machin

Re: Just found this... ;-)

2018-02-12 Thread Richard Ellis 
My Woodchuck rails and legs are all rectangle in shape ,same size. But the 
two top rails are of thicker section material .
Richard

On Sunday, February 11, 2018 at 9:42:33 PM UTC, Tim wrote:
>
> This machine is really early in legacy's history.  Take note of the 
> rectangle steel legs instead of the round.  There is also no mention of the 
> IRT name designation which the picture appears to be.  Please refer to the 
> hidden history page. http://ornamentalmills.com/history/ .
>
> Tim
>
> Sent from BlueMail  
> On Feb 10, 2018, at 4:34 PM, 'Curt George' via Legacy Ornamental Mills <
> legacy-orna...@googlegroups.com > wrote:
>>
>> Sep/Oct 1992 Fine Woodworking. 
>>
>> C.A.G. 
>>
>>
>> On Saturday, February 10, 2018 7:30 PM, 'Curt George' via Legacy 
>> Ornamental Mills > wrote:
>>
>>
>> [image: Inline image] 
>> C.A.G. 
>> -- 
>> You received this message because you are subscribed to the Google Groups 
>> "Legacy Ornamental Mills" group. 
>> To unsubscribe from this group and stop receiving emails from it, send an 
>> email to legacy-ornamental-mills+unsubscr...@googlegroups.com 
>> . 
>> To post to this group, send email to legacy-orna...@googlegroups.com 
>> . 
>> Visit this group at 
>> https://groups.google.com/group/legacy-ornamental-mills. 
>> For more options, visit https://groups.google.com/d/optout. 
>>
>>
>> -- 
>> You received this message because you are subscribed to the Google Groups 
>> "Legacy Ornamental Mills" group. 
>> To unsubscribe from this group and stop receiving emails from it, send an 
>> email to legacy-ornamental-mills+unsubscr...@googlegroups.com 
>> . 
>> To post to this group, send email to legacy-orna...@googlegroups.com 
>> . 
>> Visit this group at 
>> https://groups.google.com/group/legacy-ornamental-mills. 
>> For more options, visit https://groups.google.com/d/optout. 
>>
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this... ;-)

2018-02-11 Thread Tim Krause 
This machine is really early in legacy's history.  Take note of the rectangle 
steel legs instead of the round.  There is also no mention of the IRT name 
designation which the picture appears to be.  Please refer to the hidden 
history page. http://ornamentalmills.com/history/ .

Tim

⁣Sent from BlueMail ​

On Feb 10, 2018, 4:34 PM, at 4:34 PM, 'Curt George' via Legacy Ornamental Mills 
 wrote:
>Sep/Oct 1992 Fine Woodworking.
>C.A.G. 
>
>On Saturday, February 10, 2018 7:30 PM, 'Curt George' via Legacy
>Ornamental Mills  wrote:
> 
>
> 
>C.A.G.-- 
>You received this message because you are subscribed to the Google
>Groups "Legacy Ornamental Mills" group.
>To unsubscribe from this group and stop receiving emails from it, send
>an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
>To post to this group, send email to
>legacy-ornamental-mills@googlegroups.com.
>Visit this group at
>https://groups.google.com/group/legacy-ornamental-mills.
>For more options, visit https://groups.google.com/d/optout.
>
>
>   
>
>-- 
>You received this message because you are subscribed to the Google
>Groups "Legacy Ornamental Mills" group.
>To unsubscribe from this group and stop receiving emails from it, send
>an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
>To post to this group, send email to
>legacy-ornamental-mills@googlegroups.com.
>Visit this group at
>https://groups.google.com/group/legacy-ornamental-mills.
>For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this... ;-)

2018-02-11 Thread Richard Ellis 
Hi Curt
Just a quick pic of my Woodchuck,It was black when I bought it ,Sprayed it 
using auto paint
.Richard

On Sunday, February 11, 2018 at 12:30:30 AM UTC, Curt George wrote:
>
> [image: Inline image]
> C.A.G.
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this on YouTube

2016-03-19 Thread Brigitte Graham 
Yes, should have some sort of brace between the legs, perhaps he doesn't
need any because his floor is so spotless, he is not going hit any lumps to
jarr the legs.
But, having said that, the guy is "one of us" ~  he also has a SS in the
back round!
Legacy Widow

On 15 March 2016 at 01:34, Bill Bulkeley  wrote:

> I have also seen this one before I personally don’t like my legacy to be
> moveable, I know when space is an issue you don’t have a choice
>
> But I do so I have large blocks of metal on the base of my mill to stop it
> moving . I do a lot of hand cranking and the mill moves around when I do
> and I just like it nice and solid when I do and I have a 65X30ft shop just
> for my woodwork so I have lots of room with no need to move anything or I
> will have when I finally move in to my house
>
> Bill
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com [mailto:
> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *CURTIS GEORGE
> *Sent:* Tuesday, 15 March 2016 2:43 AM
> *To:* Legacy-Ornamental-Mills
> *Subject:* Just found this on YouTube
>
>
>
> https://www.youtube.com/watch?v=TRnH0A2sByE
> *Mobile Tool Base for Legacy Ornamental Mill .*
>
> Its not a new video made in Feb 2015. but Its not one that Ive seen before.
>
>
>
> C.A.G.
>
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2015.0.6189 / Virus Database: 4542/11814 - Release Date: 03/14/16
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To post to this group, send email to
> legacy-ornamental-mills@googlegroups.com.
> Visit this group at
> https://groups.google.com/group/legacy-ornamental-mills.
> For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To post to this group, send email to
> legacy-ornamental-mills@googlegroups.com.
> Visit this group at
> https://groups.google.com/group/legacy-ornamental-mills.
> For more options, visit https://groups.google.com/d/optout.
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

RE: Just found this on YouTube

2016-03-14 Thread Bill Bulkeley 
I have also seen this one before I personally don’t like my legacy to be 
moveable, I know when space is an issue you don’t have a choice

But I do so I have large blocks of metal on the base of my mill to stop it 
moving . I do a lot of hand cranking and the mill moves around when I do and I 
just like it nice and solid when I do and I have a 65X30ft shop just for my 
woodwork so I have lots of room with no need to move anything or I will have 
when I finally move in to my house

Bill

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE
Sent: Tuesday, 15 March 2016 2:43 AM
To: Legacy-Ornamental-Mills
Subject: Just found this on YouTube

 

https://www.youtube.com/watch?v=TRnH0A2sByE   


Mobile Tool Base for Legacy Ornamental Mill .


Its not a new video made in Feb 2015. but Its not one that Ive seen before.





C.A.G.

No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.6189 / Virus Database: 4542/11814 - Release Date: 03/14/16

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this on YouTube

2016-03-14 Thread CURTIS GEORGE 
Hello Joe and Mac 
  
I too had hoped for more from this video.  I agree that in the very least cross 
support should have been added. that looks like a pretty shaky design, even 
before the casters were added. 
Now a tool box! that would be a great idea. 
It wasn't all that long ago, I carpenter's skill would be measured by his tool 
box that he used. The Forman would judge the skills of the carpenter by the way 
he made his tool box.  
  
But ON the other hand, I should not judge this guy very hard on his skills, He 
did post a video, something that most legacy owners just do not do. 
Perhaps someday I can talk Mike to come back to my shop, and then we could make 
a good video on some Legacy ideas that most, do not use. 
Now that just might get people talking! ;-) 
  
I have to get back to work now. (My lunch is over.) 
talk to you all more latter. 
Have a good day. 
C.A.G. 
- Original Message -

From: "'joe biunno' via Legacy Ornamental Mills" 
 
To: "Legacy Ornamental Mills"  
Cc: Legacy-Ornamental-Mills@googlegroups.com 
Sent: Monday, March 14, 2016 3:54:32 PM 
Subject: Re: Just found this on YouTube 

seen this before...and have to say that the design could be a lot better, in 
that it does not remove any of the flex or twisting that can happen to a legacy 
when mounted on the original legacy legs...i would still suggest a rectangular, 
reinforced, plywood box, on wheels...eliminates all bowing of the bed and 
"racking of the rails...granted, you cannot do any joinery to the edges of 
large panels, but that is not what the legacy does best anyway...and if 
designed and constructed properly, the below space can be used for 
storage...just my opinion...hope all is well with everyone...joe 





-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this on YouTube

2016-03-14 Thread MWF 
Joe,Thanks - you always have such great input.Good to hear from you.Mac-Original Message-
From: 'joe biunno' via Legacy Ornamental Mills 
Sent: Mar 14, 2016 3:54 PM
To: Legacy Ornamental Mills 
Cc: Legacy-Ornamental-Mills@googlegroups.com
Subject: Re: Just found this on YouTube

seen this before...and have to say that the design could be a lot better, in that it does not remove any of the flex or twisting that can happen to a legacy when mounted on the original legacy legs...i would still suggest a rectangular, reinforced, plywood box, on wheels...eliminates all bowing of the bed and "racking of the rails...granted, you cannot do any joinery to the edges of large panels, but that is not what the legacy does best anyway...and if designed and constructed properly, the below space can be used for storage...just my opinion...hope all is well with everyone...joe








-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Just found this on YouTube

2016-03-14 Thread 'joe biunno' via Legacy Ornamental Mills 
seen this before...and have to say that the design could be a lot better, 
in that it does not remove any of the flex or twisting that can happen to a 
legacy when mounted on the original legacy legs...i would still suggest a 
rectangular, reinforced, plywood box, on wheels...eliminates all bowing of 
the bed and "racking of the rails...granted, you cannot do any joinery to 
the edges of large panels, but that is not what the legacy does best 
anyway...and if designed and constructed properly, the below space can be 
used for storage...just my opinion...hope all is well with everyone...joe


-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.