Re: [Linphone-users] Linphone CLI Auto Answer Not Working in Bullseye

[contact]

COME OVER and I WILL SHOW YOU


On Thursday, November 24, 2022 06:12 AM CST, Jyoti Madur  
wrote:
  Hello Team, I want to set up a Sip Client only CLI no Video in Raspberry Pi 
4, Bullseye. I have installed and configured linphone CLI in Bullseye as 
mentioned in the PDF attached. The Service is failing to start:
root@raspberrypi:~# systemctl status sippaphone.service 
● sippaphone.service - SIPPAphone
     Loaded: loaded (/etc/systemd/system/sippaphone.service; enabled; vendor 
preset: enabled)
     Active: failed (Result: exit-code) since Thu 2022-11-24 15:39:33 IST; 1h 
52min ago
    Process: 899 ExecStart=/bin/bash sippaphone.sh (code=exited, 
status=255/EXCEPTION)
        CPU: 441ms
 
Nov 24 15:39:29 raspberrypi systemd[1]: Starting SIPPAphone...
Nov 24 15:39:33 raspberrypi bash[907]: ERROR: Failed to connect pipe: No such 
file or directory
Nov 24 15:39:33 raspberrypi bash[908]: ERROR: Failed to connect pipe: No such 
file or directory
Nov 24 15:39:33 raspberrypi systemd[1]: sippaphone.service: Control process 
exited, code=exited, status=255/EXCEPTION
Nov 24 15:39:33 raspberrypi systemd[1]: sippaphone.service: Failed with result 
'exit-code'.
Nov 24 15:39:33 raspberrypi systemd[1]: Failed to start SIPPAphone.I have 
checked permissions, file name and env path for the error and everything looks 
ok. I am going nuts finding the solution for this. Any document to install and 
configure linphone CLI for auto answering will help. Please guide me on finding 
the solution for the same. Thank you.
 --Regards,
Jyoti Madur
 


 
___
Linphone-users mailing list
Linphone-users@nongnu.org
https://lists.nongnu.org/mailman/listinfo/linphone-users

Re: [Linphone-users] No Incoming Calls.

[contact]

My LG LK460 to LM Linux Mint Computer IT WORKS GOOD


On Thursday, September 15, 2022 01:56 PM CDT, Lorenzo Corgiat Mecio 
 wrote:
 Hi Paul,

I am facing a similar issue.
I was using Cisco spa303 on linphone.
It has been working fine since about two weeks ago when I stopped
getting incoming calls as well on all my hardphones.
I DID NOT change anything on the network or phone configuration.
I also tried other networks and fresh factory-reset phones with
different software versions without luck.
Devices register fine and can make calls.
For experiment I setted up a classic vintage Grandstream 2000 phone
and that seems to work.
I say it seems because calls take ages to get through. I mean, I call
and the receiving phone can sometimes take 10 seconds to start
ringing.
Other SIP providers are working fine with both setups and calls are
incoming in less than a second as usual.
I opened a topic here a few days ago but no answers so far...
I get on the phone I am calling from "User hasn't been found".
Settings are UDP.

Thank you

Skinoku

Il giorno gio 15 set 2022 alle ore 19:34 Paul Flint 
ha scritto:
>
> Hi, Newbie here, long time user of Obihai ATAs, used to doing my own setup.
>
> Here's a problem I can't seem to solve:
>
> I set up a Service Provider and Voice Service for a new Linphone account on 
> an Obi 200. It registers fine and I can initiate SIP calls to Voip.ms, 
> callcentric, and SIPBroker.
>
> I can't call it, though. I get 403 and 404 errors from voip.ms, callcentric, 
> and 2 different ways from SIPBroker: a) using the **275 route from 
> callcentric, and b) dialing from a PSTN line (in both cases using the *8954 
> proxy code for linphone).
>
> When dialing from an Obi 202, I put the URI in a speed dial slot.
>
> So, am I an idiot and missing something obvious, or is something subtle going 
> on?
>
> Thanks in advance.
>
> -- Paul.
> ___
> Linphone-users mailing list
> Linphone-users@nongnu.org
> https://lists.nongnu.org/mailman/listinfo/linphone-users

___
Linphone-users mailing list
Linphone-users@nongnu.org
https://lists.nongnu.org/mailman/listinfo/linphone-users


 
___
Linphone-users mailing list
Linphone-users@nongnu.org
https://lists.nongnu.org/mailman/listinfo/linphone-users