From: Srinivas Kandagatla <srinivas.kandaga...@linaro.org>
Thankyou Linus W, Ulf H and everyone for reviewing RFC to v3 patches.
This patch series adds Qualcomm SD Card Controller support in pl180 mmci
driver. QCom SDCC is basically a pl180, but bit more customized, some of the
register layouts and offsets are different to the ones mentioned in pl180
datasheet. The plan is to totally remove the standalone SDCC driver
drivers/mmc/host/msm_sdcc.* and start using generic mmci driver for all
Qualcomm parts, as we get chance to test on other Qcom boards.
To start using the existing mmci driver, a fake amba id for Qualcomm is added
in patches:
mmc: mmci: Add Qualcomm Id to amba id table.
Second change is, adding a 3 clock cycle delay in between writes to
CLKCTRL/POWER/DATACTRL/COMMAND registers. Most of the delays are taken care with
the existing driver except delay for the COMMAND register was too small.
This patch fixes it.
mmc: mmci: Add enough delay between writes to CMD register.
Third change is to accommodate CLK, DATCTRL and MMCICLK register layout changes
in Qcom SDCC and provide more flexibity in driver to specify these changes via
variant datastructure. Which are done in patches:
mmc: mmci: Add Qcom datactrl register variant
mmc: mmci: add ddrmode mask to variant data
mmc: mmci: add 8bit bus support in variant data
mmc: mmci: add edge support to data and command out in variant data.
mmc: mmci: add Qcom specifics of clk and datactrl registers.
mmc: mmci: Add support to data commands via variant structure.
mmc: mmci: add f_max to variant structure
mmc: mmci: add explicit clk control
Fourth major change was to add qcom specfic pio read function, the need for
this is because the way MCIFIFOCNT register behaved in QCOM SDCC is very
different to the one in pl180. This change is done in patch:
mmc: mmci: Add Qcom specific pio_read function.
Last some Qcom unrelated changes/cleanup to driver are done in patches:
mmc: mmci: use NSEC_PER_SEC macro
mmc: mmci: convert register bits to use BIT() macro.
This patches are tested in PIO mode on IFC8064 board with both eMMC and
external SD card. I would like to get this support in v3.16.
Bjorn also confirmed that there are no more CRC errors seen on sony platform.
Changes from v3:
- moved pio_read to a function pointer so as to reduce additional cycles
in hot-path, suggested by Ulf.
- simplify the flags used for explicit mclk control, suggested by Ulf.
- fixed issues in cacluating f_max and f_min pointed and suggested by
Ulf.
- removed unessary DDR flags on un-supported STE variants.
- used BIT macros as suggested by Ulf.
- removed the read/write wrappers with delays, and used most optimal way
to introduce the delays to the only registers that require delays.
Changes from v2:
- merged fbclk latch patch with clkreg_enable patch as suggested by
Linus W.
- remove qcom prefix for explicit clk control pointed by Linus W.
- cleaned up mmci_qcom_pio_read and consider SDIO as suggested by Linus
W.
Changes from v1:
- moved most of the SOC specifics to variant parameters as suggested
by Linus W.
- renamed registers as suggested by Linus W.
- Added comments in the code as suggested by Linus W.
- moved out AMBA ID addition patch from this series.
- rebased the patches to
git://git.linaro.org/people/ulf.hansson/mmc.git next
as suggested by Ulf H.
Changes from RFC:
- moved out clk setup out of spinlock as pointed by Stephen B.
If its not too late, Am hoping to get this for v3.16.
All these patches are tested on IF6410 board on both eMMC and external SD card.
Thanks,
srini
Srinivas Kandagatla (13):
mmc: mmci: use NSEC_PER_SEC macro
mmc: mmci: convert register bits to use BIT() macro.
mmc: mmci: Add Qualcomm Id to amba id table
mmc: mmci: Add enough delay between writes to CMD register.
mmc: mmci: Add Qcom datactrl register variant
mmc: mmci: add ddrmode mask to variant data
mmc: mmci: add 8bit bus support in variant data
mmc: mmci: add edge support to data and command out in variant data.
mmc: mmci: add Qcom specifics of clk and datactrl registers.
mmc: mmci: Add support to data commands via variant structure.
mmc: mmci: add f_max to variant structure
mmc: mmci: add explicit clk control
mmc: mmci: Add Qcom specific pio_read function.
drivers/mmc/host/mmci.c | 203 +++++++++++++++++++++++++++++++++---------
drivers/mmc/host/mmci.h | 228 ++++++++++++++++++++++++++----------------------
2 files changed, 288 insertions(+), 143 deletions(-)
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
