Hi,
I noticed that the initial-tuning-data files for Swedish dvb-t are a bit
outdated and spent some time to generate new ones.
Since it's 220 tuning files I tar:ed them and placed the archive here:
http://boomer.se/tmp/initial-tuning-data.se-2006-11-15.tar.gz
Regards,
Richard
On Wed, 15 Nov 2006, andrea venturi wrote:
Graham Leggett wrote:
Hi all,
I have been searching for a USB2 DVB-S receiver that is capable of receiving
a full transport stream, with working Linux drivers.
The last time I looked, the only USB capable receivers out there were v1.1,
Hi,
On Wed, 15 Nov 2006, Steven Cockeram wrote:
Dave Leatherdale wrote:
Hi
I recently got a few of the Hauppauge nova-t stick devices. I tried using
the latest source from http://linuxtv.org/hg/v4l-dvb and the /~pb/v4l-dvb
trees but I always get no frontend was attached. I'm running
Hi,
I just ask Mauro to pull a fix for the Usage counter from
http://linuxtv.org/hg/~pb/v4l-dvb .
It should cure the situation.
Patrick.
--
Mail: [EMAIL PROTECTED]
WWW: http://www.wi-bw.tfh-wildau.de/~pboettch/
On Fri, 10 Nov 2006, Matthias Schwarzott wrote:
Hi There!
I have these
Hi Stefan,
I've exactly the same error when I plug that stick into a USB 1.1 port.
Make sur it negociate high speed USB and not full speed.
Guy
On Tue, 14 Nov 2006 18:57:07 +0100
Stefan Schweizer [EMAIL PROTECTED] wrote:
Hi,
the Freecom dvb-t receiver that I bought last week gives
Hi,
On 11/15/06, Mark Howells [EMAIL PROTECTED] wrote:
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Stefan Schweizer
Sent: 14 November 2006 18:34
To: linux-dvb@linuxtv.org
Subject: [linux-dvb] RE: Freecom - recv bulk message failed: -110
-Original Message-
From: Markus Rechberger [mailto:[EMAIL PROTECTED]
Sent: 15 November 2006 10:37
To: Mark Howells
Cc: Stefan Schweizer; linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] RE: Freecom - recv bulk message failed: -110
Do
you think it has something to do with
On 11/15/06, Mark Howells [EMAIL PROTECTED] wrote:
-Original Message-
From: Markus Rechberger [mailto:[EMAIL PROTECTED]
Sent: 15 November 2006 10:37
To: Mark Howells
Cc: Stefan Schweizer; linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] RE: Freecom - recv bulk message failed: -110
I have the Nova-T 500 Dual card fully working under windows with a reception of
95% When using the latest dvb-usb-dib0700-module I cannot get a lock when using
svbtune or scan.
get a maximum of 50% reception in Kaffeine = no lock And I do not move my
antenna!
Firmware used :
I installed Kaffeine from source today.
It appeared that the version I was using didn't have dvb support :)
So now I can do a channel scan with Kaffeine.
It does find the same channels I get with dvb-scan or mythtv.
I don't have to reboot after each transponder with Kaffeine.
However it does not
Hello,
This small patch enables video over s-video and composite1.
One question : i 'm unable to test sound via line-in in my card ?
i've tested it with :
mplayer tv://23 -vo x11 -tv
tomlohave wrote:
Hello,
This small patch enables video over s-video and composite1.
One question : i 'm unable to test sound via line-in in my card ?
Tom,
The .amux value is the audio mux -- this might be set incorrectly, if you
are not hearing audio. Try and see if LINE1 works, instead.
---BeginMessage---
tomlohave wrote:
Hello,
This small patch enables video over s-video and composite1.
One question : i 'm unable to test sound via line-in in my card ?
Tom,
The .amux value is the audio mux -- this might be set incorrectly, if you
are not hearing audio. Try and see if
---BeginMessage---
Michael Krufky a écrit :
tomlohave wrote:
Hello,
This small patch enables video over s-video and composite1.
One question : i 'm unable to test sound via line-in in my card ?
Tom,
The .amux value is the audio mux -- this might be set incorrectly, if you
are not
Joep,
Within windows with the Twinhan Software scanning for the dutch channels
does not work either. It does not find any dutch channels.
Regards,
Michel.
(Still working to get it working on my fc5)
joep admiraal schreef:
I installed Kaffeine from source today.
It appeared that the version
Can you both play with the msleep in dib0700_core.c:232 ? It is already at
500ms (normally it should be 100ms) .
I tried it at both 10,000ms and 100ms, same as before.
I wish companies would open up their specs a bit more. I could spend
time reading them rather than waiting for someone
16 matches
Mail list logo
