OK-OK. The " It does fix PPv2.1 support, which was broken" is great reason!
-Original Message-
From: Antoine Tenart
Sent: Thursday, February 28, 2019 5:51 PM
To: Yan Markman
Cc: Antoine Tenart ; da...@davemloft.net;
li...@armlinux.org.uk; net...@vger.kernel.org; li
else is correct also for the
MVPP2_SINGLE_RESOURCE_MODE,
but new/patched isn't.
Since this patch doesn't change any functionality (right now) but reduces the
flexibility I do not see real reason to apply it.
Regards
Yan Markman
-Original Message-
From: Antoine Tenart
Sent: Thur
Hi
The eth-down/stop may concurrent with pre-scheduled stats_work.
So it seems better to cancel stats_work first and then make resetS.
Yan Markman
-Original Message-
From: Antoine Tenart
Sent: Thursday, February 28, 2019 3:21 PM
To: da...@davemloft.net; li...@armlinux.org.uk
Cc
Hi Florian
Please keep CC Yelena Krivosheev
for changes withdrivers/net/ethernet/marvell/mvneta.c
Thanks
Yan Markman
Tel. 05-44732819
-Original Message-
From: Florian Fainelli [mailto:f.faine...@gmail.com]
Sent: Thursday, March 29, 2018 1:44 AM
To: net
Hi Florian
Please keep CC Yelena Krivosheev
for changes withdrivers/net/ethernet/marvell/mvneta.c
Thanks
Yan Markman
Tel. 05-44732819
-Original Message-
From: Florian Fainelli [mailto:f.faine...@gmail.com]
Sent: Thursday, March 29, 2018 1:44 AM
To: net
Hi Florian
Please keep CC Yelena Krivosheev
for changes withdrivers/net/ethernet/marvell/mvneta.c
Thanks
Yan Markman
Tel. 05-44732819
-Original Message-
From: Florian Fainelli [mailto:f.faine...@gmail.com]
Sent: Thursday, March 29, 2018 1:44 AM
To: net
Thanks David
We are aware and it is working properly
Yan Markman
-Original Message-
From: David Miller [mailto:da...@davemloft.net]
Sent: Tuesday, March 27, 2018 8:16 PM
To: maxime.chevall...@bootlin.com
Cc: Yan Markman ; net...@vger.kernel.org;
linux-kernel@vger.kernel.org
check the correctnes of new "mvpp2_prs_entry pe" without
memset(pe, 0, sizeof(pe));
in all procedures where pe=kzalloc() has been replaced
Thanks
Yan Markman
Tel. 05-44732819
-Original Message-
From: Maxime Chevallier [mailto:maxime.chevall...@bootlin.com]
Sent: Wednesd
The DTS-patch for this board (in "old" format) is attached
Yan Markman
Tel. 05-44732819
-Original Message-
From: Stefan Chulski
Sent: Monday, March 19, 2018 2:58 PM
To: Russell King - ARM Linux ; Antoine Tenart
Cc: da...@davemloft.net; kis...@ti.com; gregory.clem...@b
I will make this tomorrow.
Thanks for attention!
Best regards
Yan Markman
Tel. 05-44732819
-Original Message-
From: Antoine Tenart [mailto:antoine.ten...@bootlin.com]
Sent: Tuesday, February 27, 2018 7:14 PM
To: David Miller
Cc: antoine.ten...@bootlin.com; Yan Markman ;
m
UP but FALSE on down
netif_carrier_off(port->dev);//YANM
BTW: It's seems your below patch should be present anyway.
+++ b/drivers/net/phy/phylink.c
@@ -798,6 +798,7 @@ void phylink_disconnect_phy(struct phylink *pl)
+ pl->phy_state.link = false;
Thank you
Best regards
Yan Markman
essage-
From: Russell King - ARM Linux [mailto:li...@armlinux.org.uk]
Sent: Wednesday, November 29, 2017 11:21 PM
To: Yan Markman
Cc: Antoine Tenart ; and...@lunn.ch;
f.faine...@gmail.com; da...@davemloft.net; gregory.clem...@free-electrons.com;
thomas.petazz...@free-electrons.com; miquel.ray..
down the callback
pl->ops->mac_link_down(ndev, pl->link_an_mode);
would be called, but it isn't
-Original Message-
From: Russell King - ARM Linux [mailto:li...@armlinux.org.uk]
Sent: Wednesday, November 29, 2017 9:59 PM
To: Yan Markman
Cc: Antoine Tenart ; an
re passing over full graceful down/reset
state.
The further ifconfig-up starts with old state parameters.
Special cases not-tested but logic 2 test-cases are:
remote side changes speed whilst link is Down or Disconnected. But local
ifconfig-up starts with old speed.
Best
14 matches
Mail list logo
