Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Hi Adam, On Wed, Oct 02, 2019 at 02:03:52PM -0500, Adam Ford wrote: > On Tue, Mar 19, 2019 at 8:33 AM Sebastian Reichel wrote: > After a bunch of testing, I think the issue I was having was the BTS > file being pulled in from linux-firmware. I was able to successfully > load a BTS file that I have from Logic PD with working BLE and BT > working together. I have to run some tests, but if you wouldn't mind > re-basing your code and pushing it again for review, I can most likely > add my 'tested-by'. > > I am not sure who to discuss my perceived bug in the BTS blob. I have > to go find the old BTS editor and see if I can determine the cause, > but the fact that I can use the BTS file that corresponds to the FCC > certified file that Logic PD used is more important to me than using > the generic BTS file provided by TI, however it would be nice for the > reference BTS file to operate without error. nice :) I just send a rebased partial series. I need some more time for the FM radio part (I plan to work on that within the next 3 weeks). -- Sebastian signature.asc Description: PGP signature
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
On Tue, Mar 19, 2019 at 8:33 AM Sebastian Reichel wrote: > > Hi Hans, > > On Thu, Mar 14, 2019 at 09:20:10AM +0100, Hans Verkuil wrote: > > On 12/21/18 2:17 AM, Sebastian Reichel wrote: > > > This moves all remaining users of the legacy TI_ST driver to hcill > > > (patches > > > 1-3). Then patches 4-7 convert wl128x-radio driver to a standard platform > > > device driver with support for multiple instances. Patch 7 will result in > > > (userless) TI_ST driver no longer supporting radio at runtime. Patch 8-11 > > > do > > > some cleanups in the wl128x-radio driver. Finally patch 12 removes the > > > TI_ST > > > specific parts from wl128x-radio and adds the required infrastructure to > > > use it > > > with the serdev hcill driver instead. The remaining patches 13 and 14 > > > remove > > > the old TI_ST code. > > > > > > The new code has been tested on the Motorola Droid 4. For testing the > > > audio > > > should be configured to route Ext to Speaker or Headphone. Then you need > > > to > > > plug headphone, since its cable is used as antenna. For testing there is a > > > 'radio' utility packages in Debian. When you start the utility you need to > > > specify a frequency, since initial get_frequency returns an error: > > > > What is the status of this series? > > > > Based on some of the replies (from Adam Ford in particular) it appears that > > this isn't ready to be merged, so is a v2 planned? > > Yes, a v2 is planned, but I'm super busy at the moment. I don't > expect to send something for this merge window. Neither LogicPD > nor IGEP use FM radio, so I can just remove FM support from the > TI_ST framework. Converting those platforms to hci_ll can be done > in a different patchset. > Sebastian, After a bunch of testing, I think the issue I was having was the BTS file being pulled in from linux-firmware. I was able to successfully load a BTS file that I have from Logic PD with working BLE and BT working together. I have to run some tests, but if you wouldn't mind re-basing your code and pushing it again for review, I can most likely add my 'tested-by' I am not sure who to discuss my perceived bug in the BTS blob. I have to go find the old BTS editor and see if I can determine the cause, but the fact that I can use the BTS file that corresponds to the FCC certified file that Logic PD used is more important to me than using the generic BTS file provided by TI, however it would be nice for the reference BTS file to operate without error. adam > If that was the only issue there would be a v2 already. But Marcel > Holtmann suggested to pass the custom packet data through the BT > subsystem, which is non-trivial (at least for me) :) > > -- Sebastian
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
On Fri, May 10, 2019 at 10:38 AM Marcel Holtmann wrote:
>
> Hi Adam,
>
> >>> This moves all remaining users of the legacy TI_ST driver to hcill
> >>> (patches
> >>> 1-3). Then patches 4-7 convert wl128x-radio driver to a standard
> >>> platform
> >>> device driver with support for multiple instances. Patch 7 will
> >>> result in
> >>> (userless) TI_ST driver no longer supporting radio at runtime. Patch
> >>> 8-11 do
> >>> some cleanups in the wl128x-radio driver. Finally patch 12 removes
> >>> the TI_ST
> >>> specific parts from wl128x-radio and adds the required infrastructure
> >>> to use it
> >>> with the serdev hcill driver instead. The remaining patches 13 and 14
> >>> remove
> >>> the old TI_ST code.
> >>>
> >>> The new code has been tested on the Motorola Droid 4. For testing the
> >>> audio
> >>> should be configured to route Ext to Speaker or Headphone. Then you
> >>> need to
> >>> plug headphone, since its cable is used as antenna. For testing there
> >>> is a
> >>> 'radio' utility packages in Debian. When you start the utility you
> >>> need to
> >>> specify a frequency, since initial get_frequency returns an error:
> >>
> >> What is the status of this series?
> >>
> >> Based on some of the replies (from Adam Ford in particular) it appears
> >> that
> >> this isn't ready to be merged, so is a v2 planned?
> >
> > Yes, a v2 is planned, but I'm super busy at the moment. I don't
> > expect to send something for this merge window. Neither LogicPD
> > nor IGEP use FM radio, so I can just remove FM support from the
> > TI_ST framework. Converting those platforms to hci_ll can be done
> > in a different patchset.
> >
> > If that was the only issue there would be a v2 already. But Marcel
> > Holtmann suggested to pass the custom packet data through the BT
> > subsystem, which is non-trivial (at least for me) :)
>
> I am running some tests today on the wl1283-st on the Logic PD Torpedo
> board. Tony had suggested a few options, so I'm going to try those.
> Looking at those today. If/when you have a V2, please CC me on it. If
> it's been posted, can you send me a link? I would really like to see
> the st-kim driver go away so I'd like to resolve the issues with the
> torpedo board.
> >>>
> >>> I have run a bunch of tests on the 5.1 kernel. I am able to get the
> >>> firmware to load now and the hci0 goes up. I was able to establish a
> >>> BLE connection to a TI Sensor Tag and read and write data to it with
> >>> good success on the wl1283.
> >>>
> >>> Unfortunately, when I tried to do some more extensive testing over
> >>> classic Bluetooth, I got an error that repeats itself at seemingly
> >>> random intervals:
> >>> Bluetooth: hci0: Frame reassembly failed (-84)
> >>>
> >>> I can still scan and pair, but these Frame reassembly failed errors
> >>> appear to come and go.
> >>
> >> there are only 3 places in h4_recv_buf that return EILSEQ. Just add an
> >> extra printk to these to figure out which one it is. Maybe it is just
> >> extra packet types that we need to handle. If it is not the packet type
> >> one, print what packet we have that is causing this.
> >>
> >
> > I added some code around
> >
> > /* Check for invalid packet type */
> >if (!skb) {
> > printk("Check for invalid packet type %x\n", (unsigned int)
> > ([i])->type);
> > return ERR_PTR(-EILSEQ);
> > }
> >
> > I don't know if I did it right or I am reading the packet type
> > correctly, but the frame reassembly errors are being caught here.
> >
> > [ 408.519165] Check for invalid packet type ff
> > [ 408.523559] Bluetooth: hci0: Frame reassembly failed (-84)
>
> so now we need to figure our on how to handle HCI_VENDOR_PKT.
>
> #define LL_RECV_VENDOR \
> .type = HCI_VENDOR_PKT, \
> .hlen = aaa, \
> .loff = bbb, \
> .lsize = ccc, \
> .maxlen = ddd
>
> static const struct h4_recv_pkt ll_recv_pkts[] = {
> ...
> { LL_RECV_WAKE_ACK, .recv = ll_recv_frame },
> { LL_RECV_VENDOR,.recv = hci_recv_diag },
> };
>
> Can you hexdump the data inside the skb and we can figure out what it uses
> for the header and size.
>
> In hci_bcm.c there are a few examples of fixed size packets and bpa10x.c
> contains one where it follows an actual header definition. Also hci_nokia.c
> contains a few for their packets.
I haven't forgotten this, but I was highly distracted. I wanted to
test a bunch of stuff on omap3630 and imx6 boards to prep them for the
upcoming 5.4 LTS kernel. As of now I 'think' this is the last item on
my to-do list.
I'm going to try and throw some debug code into the older st/kim
driver as well as debug this. I know some people have stated they
have wl1283-st working on a dm3730. dump some logs? I am curious to
see if there is
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Hi Adam,
>>> This moves all remaining users of the legacy TI_ST driver to hcill
>>> (patches
>>> 1-3). Then patches 4-7 convert wl128x-radio driver to a standard
>>> platform
>>> device driver with support for multiple instances. Patch 7 will result
>>> in
>>> (userless) TI_ST driver no longer supporting radio at runtime. Patch
>>> 8-11 do
>>> some cleanups in the wl128x-radio driver. Finally patch 12 removes the
>>> TI_ST
>>> specific parts from wl128x-radio and adds the required infrastructure
>>> to use it
>>> with the serdev hcill driver instead. The remaining patches 13 and 14
>>> remove
>>> the old TI_ST code.
>>>
>>> The new code has been tested on the Motorola Droid 4. For testing the
>>> audio
>>> should be configured to route Ext to Speaker or Headphone. Then you
>>> need to
>>> plug headphone, since its cable is used as antenna. For testing there
>>> is a
>>> 'radio' utility packages in Debian. When you start the utility you need
>>> to
>>> specify a frequency, since initial get_frequency returns an error:
>>
>> What is the status of this series?
>>
>> Based on some of the replies (from Adam Ford in particular) it appears
>> that
>> this isn't ready to be merged, so is a v2 planned?
>
> Yes, a v2 is planned, but I'm super busy at the moment. I don't
> expect to send something for this merge window. Neither LogicPD
> nor IGEP use FM radio, so I can just remove FM support from the
> TI_ST framework. Converting those platforms to hci_ll can be done
> in a different patchset.
>
> If that was the only issue there would be a v2 already. But Marcel
> Holtmann suggested to pass the custom packet data through the BT
> subsystem, which is non-trivial (at least for me) :)
I am running some tests today on the wl1283-st on the Logic PD Torpedo
board. Tony had suggested a few options, so I'm going to try those.
Looking at those today. If/when you have a V2, please CC me on it. If
it's been posted, can you send me a link? I would really like to see
the st-kim driver go away so I'd like to resolve the issues with the
torpedo board.
>>>
>>> I have run a bunch of tests on the 5.1 kernel. I am able to get the
>>> firmware to load now and the hci0 goes up. I was able to establish a
>>> BLE connection to a TI Sensor Tag and read and write data to it with
>>> good success on the wl1283.
>>>
>>> Unfortunately, when I tried to do some more extensive testing over
>>> classic Bluetooth, I got an error that repeats itself at seemingly
>>> random intervals:
>>> Bluetooth: hci0: Frame reassembly failed (-84)
>>>
>>> I can still scan and pair, but these Frame reassembly failed errors
>>> appear to come and go.
>>
>> there are only 3 places in h4_recv_buf that return EILSEQ. Just add an extra
>> printk to these to figure out which one it is. Maybe it is just extra packet
>> types that we need to handle. If it is not the packet type one, print what
>> packet we have that is causing this.
>>
>
> I added some code around
>
> /* Check for invalid packet type */
>if (!skb) {
> printk("Check for invalid packet type %x\n", (unsigned int)
> ([i])->type);
> return ERR_PTR(-EILSEQ);
> }
>
> I don't know if I did it right or I am reading the packet type
> correctly, but the frame reassembly errors are being caught here.
>
> [ 408.519165] Check for invalid packet type ff
> [ 408.523559] Bluetooth: hci0: Frame reassembly failed (-84)
so now we need to figure our on how to handle HCI_VENDOR_PKT.
#define LL_RECV_VENDOR \
.type = HCI_VENDOR_PKT, \
.hlen = aaa, \
.loff = bbb, \
.lsize = ccc, \
.maxlen = ddd
static const struct h4_recv_pkt ll_recv_pkts[] = {
...
{ LL_RECV_WAKE_ACK, .recv = ll_recv_frame },
{ LL_RECV_VENDOR,.recv = hci_recv_diag },
};
Can you hexdump the data inside the skb and we can figure out what it uses for
the header and size.
In hci_bcm.c there are a few examples of fixed size packets and bpa10x.c
contains one where it follows an actual header definition. Also hci_nokia.c
contains a few for their packets.
Regards
Marcel
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
On Thu, Mar 14, 2019 at 3:21 AM Hans Verkuil wrote: > > Hi Sebastian, > > On 12/21/18 2:17 AM, Sebastian Reichel wrote: > > Hi, > > > > This moves all remaining users of the legacy TI_ST driver to hcill (patches > > 1-3). Then patches 4-7 convert wl128x-radio driver to a standard platform > > device driver with support for multiple instances. Patch 7 will result in > > (userless) TI_ST driver no longer supporting radio at runtime. Patch 8-11 do > > some cleanups in the wl128x-radio driver. Finally patch 12 removes the TI_ST > > specific parts from wl128x-radio and adds the required infrastructure to > > use it > > with the serdev hcill driver instead. The remaining patches 13 and 14 remove > > the old TI_ST code. > > > > The new code has been tested on the Motorola Droid 4. For testing the audio > > should be configured to route Ext to Speaker or Headphone. Then you need to > > plug headphone, since its cable is used as antenna. For testing there is a > > 'radio' utility packages in Debian. When you start the utility you need to > > specify a frequency, since initial get_frequency returns an error: > > What is the status of this series? > > Based on some of the replies (from Adam Ford in particular) it appears that > this isn't ready to be merged, so is a v2 planned? If you can leave the Logic PD Torpedo board alone and don't remove the legacy st driver for now, go ahead and migrate the others. I know what you proposed 'should' work on my board, but I don't know why it doesn't. In fact other boards I maintain use your method, but it just doesn't work on the Torpedo and I don't know why. (it's not for lack of trying) adam > > Regards, > > Hans > > > > > $ radio -f 100.0 > > > > Merry Christmas! > > > > -- Sebastian > > > > Sebastian Reichel (14): > > ARM: dts: LogicPD Torpedo: Add WiLink UART node > > ARM: dts: IGEP: Add WiLink UART node > > ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support > > media: wl128x-radio: remove module version > > media: wl128x-radio: remove global radio_disconnected > > media: wl128x-radio: remove global radio_dev > > media: wl128x-radio: convert to platform device > > media: wl128x-radio: use device managed memory allocation > > media: wl128x-radio: load firmware from ti-connectivity/ > > media: wl128x-radio: simplify fmc_prepare/fmc_release > > media: wl128x-radio: fix skb debug printing > > media: wl128x-radio: move from TI_ST to hci_ll driver > > Bluetooth: btwilink: drop superseded driver > > misc: ti-st: Drop superseded driver > > > > .../boot/dts/logicpd-torpedo-37xx-devkit.dts | 8 + > > arch/arm/boot/dts/omap3-igep0020-rev-f.dts| 8 + > > arch/arm/boot/dts/omap3-igep0030-rev-g.dts| 8 + > > arch/arm/mach-omap2/pdata-quirks.c| 52 - > > drivers/bluetooth/Kconfig | 11 - > > drivers/bluetooth/Makefile| 1 - > > drivers/bluetooth/btwilink.c | 350 --- > > drivers/bluetooth/hci_ll.c| 115 ++- > > drivers/media/radio/wl128x/Kconfig| 2 +- > > drivers/media/radio/wl128x/fmdrv.h| 5 +- > > drivers/media/radio/wl128x/fmdrv_common.c | 211 ++-- > > drivers/media/radio/wl128x/fmdrv_common.h | 4 +- > > drivers/media/radio/wl128x/fmdrv_v4l2.c | 55 +- > > drivers/media/radio/wl128x/fmdrv_v4l2.h | 2 +- > > drivers/misc/Kconfig | 1 - > > drivers/misc/Makefile | 1 - > > drivers/misc/ti-st/Kconfig| 18 - > > drivers/misc/ti-st/Makefile | 6 - > > drivers/misc/ti-st/st_core.c | 922 -- > > drivers/misc/ti-st/st_kim.c | 868 - > > drivers/misc/ti-st/st_ll.c| 169 > > include/linux/ti_wilink_st.h | 337 +-- > > 22 files changed, 213 insertions(+), 2941 deletions(-) > > delete mode 100644 drivers/bluetooth/btwilink.c > > delete mode 100644 drivers/misc/ti-st/Kconfig > > delete mode 100644 drivers/misc/ti-st/Makefile > > delete mode 100644 drivers/misc/ti-st/st_core.c > > delete mode 100644 drivers/misc/ti-st/st_kim.c > > delete mode 100644 drivers/misc/ti-st/st_ll.c > > >
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Hi, On Sat, Dec 22, 2018 at 09:08:28PM +0100, Pavel Machek wrote: > Merry Christmas! > > > This moves all remaining users of the legacy TI_ST driver to hcill (patches > > 1-3). Then patches 4-7 convert wl128x-radio driver to a standard platform > > device driver with support for multiple instances. Patch 7 will result in > > (userless) TI_ST driver no longer supporting radio at runtime. Patch 8-11 do > > some cleanups in the wl128x-radio driver. Finally patch 12 removes the TI_ST > > specific parts from wl128x-radio and adds the required infrastructure to > > use it > > with the serdev hcill driver instead. The remaining patches 13 and 14 remove > > the old TI_ST code. > > > > The new code has been tested on the Motorola Droid 4. For testing the audio > > should be configured to route Ext to Speaker or Headphone. Then you need to > > plug headphone, since its cable is used as antenna. For testing there is a > > 'radio' utility packages in Debian. When you start the utility you need to > > specify a frequency, since initial get_frequency returns an error: > > > > $ radio -f 100.0 > > Ok, it seems the driver does not work built-in, due to firmware issue: > > root@devuan:/home/user# dmesg | grep wl12 > [1.018951] reg-fixed-voltage regulator-wl12xx: GPIO lookup for > consumer (null) > [1.026550] reg-fixed-voltage regulator-wl12xx: using device tree > for GPIO lookup > [1.034271] of_get_named_gpiod_flags: can't parse 'gpios' property > of node '/regulator-wl12xx[0]' > [1.043487] of_get_named_gpiod_flags: parsed 'gpio' property of > node '/regulator-wl12xx[0]' - status (0) > [4.151885] wl12xx_driver wl12xx.1.auto: Direct firmware load for > ti-connectivity/wl128x-nvs.bin failed with error -2 > [ 11.368286] vwl1271: disabling > root@devuan:/home/user# find /lib/firmware/ | grep wl128 > /lib/firmware/ti-connectivity/wl128x-fw-5-plt.bin > /lib/firmware/ti-connectivity/wl128x-fw-5-mr.bin > /lib/firmware/ti-connectivity/wl128x-fw-5-sr.bin > /lib/firmware/ti-connectivity/wl128x-nvs.bin > root@devuan:/home/user# > > Ideas welcome... ... ... am I supposed to compile wl128-nvs.bin into > the kernel using EXTRA_FIRMWARE? This is due to the driver loading before the rootfs is available. You can workaround this without touching your kernel configuration by rebinding the driver via sysfs: https://lwn.net/Articles/143397/ -- Sebastian signature.asc Description: PGP signature
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
* Adam Ford [181222 20:36]: > As much as I'd like to see the ti-st kim stuff go, I am not able to > load the Bluetooth on the Torpedo board (wl1283). The hooks on a > different, wl18xx and 127x board work fine. I am not sure if there is > anything different about the wl1283, but I don't have any other boards > other than the Logic PD Torpedo kit. Do you have any wl1283 boards to > test? I'd like to see this BT timeout stuff resolved before we dump > the ti-st kim stuff, otherwise, I'll forever be porting drivers. :-( Sebastian and I both tested this with droid 4, which has wl1283. So it's probably some missing GPIO/regulator/pinconf stuff that the pdata-quirks.c does for you. Maybe try adding back also the pdata-quirks.c code and see if that helps? Regards, Tony
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
* Sebastian Reichel [181222 02:48]: > On Fri, Dec 21, 2018 at 10:02:05AM -0800, Tony Lindgren wrote: > > Hmm so looks like nothing to configure for the clocks or > > CPCAP_BIT_ST_L_TIMESLOT bits for cap for the EXT? So the > > wl12xx audio is wired directly to cpcap EXT then and not a > > TDM slot on the mcbsp huh? > > For FM radio it's directly wired to EXT with no DAI being required. > I think that EXT is only used by FM radio and not by bluetooth. BT > seems to use TDM. OK then it sounds like we just need a diff -u of the cpcap regs from Android with cpcaprw --all before and after using a bluetooth headset during a voice call to configure it for voice calls for the TDM. I think snd-soc-motmd just needs the voice output specified in the mixer in addition to the cpcap configuration. I don't think have any bluetooth audio gear though, maybe somebody using a headset can post the diff. Regards, Tony
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Hi! > > This moves all remaining users of the legacy TI_ST driver to hcill (patches > > 1-3). Then patches 4-7 convert wl128x-radio driver to a standard platform > > device driver with support for multiple instances. Patch 7 will result in > > (userless) TI_ST driver no longer supporting radio at runtime. Patch 8-11 do > > some cleanups in the wl128x-radio driver. Finally patch 12 removes the TI_ST > > specific parts from wl128x-radio and adds the required infrastructure to > > use it > > with the serdev hcill driver instead. The remaining patches 13 and 14 remove > > the old TI_ST code. > > > > The new code has been tested on the Motorola Droid 4. For testing the audio > > should be configured to route Ext to Speaker or Headphone. Then you need to > > plug headphone, since its cable is used as antenna. For testing there is a > > 'radio' utility packages in Debian. When you start the utility you need to > > specify a frequency, since initial get_frequency returns an error: > > > > $ radio -f 100.0 > > Ok, it seems the driver does not work built-in, due to firmware issue: > > root@devuan:/home/user# dmesg | grep wl12 > [1.018951] reg-fixed-voltage regulator-wl12xx: GPIO lookup for > consumer (null) > [1.026550] reg-fixed-voltage regulator-wl12xx: using device tree > for GPIO lookup > [1.034271] of_get_named_gpiod_flags: can't parse 'gpios' property > of node '/regulator-wl12xx[0]' > [1.043487] of_get_named_gpiod_flags: parsed 'gpio' property of > node '/regulator-wl12xx[0]' - status (0) > [4.151885] wl12xx_driver wl12xx.1.auto: Direct firmware load for > ti-connectivity/wl128x-nvs.bin failed with error -2 > [ 11.368286] vwl1271: disabling > root@devuan:/home/user# find /lib/firmware/ | grep wl128 > /lib/firmware/ti-connectivity/wl128x-fw-5-plt.bin > /lib/firmware/ti-connectivity/wl128x-fw-5-mr.bin > /lib/firmware/ti-connectivity/wl128x-fw-5-sr.bin > /lib/firmware/ti-connectivity/wl128x-nvs.bin > root@devuan:/home/user# > > Ideas welcome... ... ... am I supposed to compile wl128-nvs.bin into > the kernel using EXTRA_FIRMWARE? EXTRA_FIRMWARE gets me further... some of it was not in debian. "Speaker right" needs to be set to "Ext" in alsamixer, and then... it works! :-) Quality does not seem to be great, but that may be mixer settings or something. Thanks! Pavel Tested-by: Pavel Machek -- (english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html signature.asc Description: Digital signature
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
On Sat, Dec 22, 2018 at 11:09 AM Tony Lindgren wrote: > > * Sebastian Reichel [181221 01:18]: > > The new code has been tested on the Motorola Droid 4. For testing the audio > > should be configured to route Ext to Speaker or Headphone. Then you need to > > plug headphone, since its cable is used as antenna. For testing there is a > > 'radio' utility packages in Debian. When you start the utility you need to > > specify a frequency, since initial get_frequency returns an error: > > Nice, good to see that ti-st kim stuff gone :) I gave this a quick Tony, As much as I'd like to see the ti-st kim stuff go, I am not able to load the Bluetooth on the Torpedo board (wl1283). The hooks on a different, wl18xx and 127x board work fine. I am not sure if there is anything different about the wl1283, but I don't have any other boards other than the Logic PD Torpedo kit. Do you have any wl1283 boards to test? I'd like to see this BT timeout stuff resolved before we dump the ti-st kim stuff, otherwise, I'll forever be porting drivers. :-( adam > try using fmtools.git and fmscan works just fine. No luck yet with > fm though, it gives VIDIOC_G_CTRL: Not a tty error somehow so > maybe I'm missing some options, patch below for omap2plus_defconfig. > > Hmm so looks like nothing to configure for the clocks or > CPCAP_BIT_ST_L_TIMESLOT bits for cap for the EXT? So the > wl12xx audio is wired directly to cpcap EXT then and not a > TDM slot on the mcbsp huh? > > > Merry Christmas! > > Same to you! > > Tony > > 8< > From tony Mon Sep 17 00:00:00 2001 > From: Tony Lindgren > Date: Fri, 21 Dec 2018 07:57:09 -0800 > Subject: [PATCH] ARM: omap2plus_defconfig: Add RADIO_WL128X as a loadable > module > > This allows using the FM radio in the wl12xx chips after modprobe > fm_drv using radio from xawt, or fmtools. > > Note that the firmware placed into /lib/firmware/ti-connectivity > directory: > > fm_rx_ch8_1283.2.bts > fmc_ch8_1283.2.bts > > Signed-off-by: Tony Lindgren > --- > arch/arm/configs/omap2plus_defconfig | 3 +++ > 1 file changed, 3 insertions(+) > > diff --git a/arch/arm/configs/omap2plus_defconfig > b/arch/arm/configs/omap2plus_defconfig > --- a/arch/arm/configs/omap2plus_defconfig > +++ b/arch/arm/configs/omap2plus_defconfig > @@ -126,6 +126,7 @@ CONFIG_AF_RXRPC=m > CONFIG_RXKAD=y > CONFIG_CFG80211=m > CONFIG_MAC80211=m > +CONFIG_RFKILL=m > CONFIG_DEVTMPFS=y > CONFIG_DEVTMPFS_MOUNT=y > CONFIG_DMA_CMA=y > @@ -343,12 +344,14 @@ CONFIG_IR_GPIO_TX=m > CONFIG_IR_PWM_TX=m > CONFIG_MEDIA_SUPPORT=m > CONFIG_MEDIA_CAMERA_SUPPORT=y > +CONFIG_MEDIA_RADIO_SUPPORT=y > CONFIG_MEDIA_CEC_SUPPORT=y > CONFIG_MEDIA_CONTROLLER=y > CONFIG_VIDEO_V4L2_SUBDEV_API=y > CONFIG_V4L_PLATFORM_DRIVERS=y > CONFIG_VIDEO_OMAP3=m > CONFIG_CEC_PLATFORM_DRIVERS=y > +CONFIG_RADIO_WL128X=m > # CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set > CONFIG_VIDEO_TVP5150=m > CONFIG_DRM=m > -- > 2.19.2
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Merry Christmas! > This moves all remaining users of the legacy TI_ST driver to hcill (patches > 1-3). Then patches 4-7 convert wl128x-radio driver to a standard platform > device driver with support for multiple instances. Patch 7 will result in > (userless) TI_ST driver no longer supporting radio at runtime. Patch 8-11 do > some cleanups in the wl128x-radio driver. Finally patch 12 removes the TI_ST > specific parts from wl128x-radio and adds the required infrastructure to use > it > with the serdev hcill driver instead. The remaining patches 13 and 14 remove > the old TI_ST code. > > The new code has been tested on the Motorola Droid 4. For testing the audio > should be configured to route Ext to Speaker or Headphone. Then you need to > plug headphone, since its cable is used as antenna. For testing there is a > 'radio' utility packages in Debian. When you start the utility you need to > specify a frequency, since initial get_frequency returns an error: > > $ radio -f 100.0 Ok, it seems the driver does not work built-in, due to firmware issue: root@devuan:/home/user# dmesg | grep wl12 [1.018951] reg-fixed-voltage regulator-wl12xx: GPIO lookup for consumer (null) [1.026550] reg-fixed-voltage regulator-wl12xx: using device tree for GPIO lookup [1.034271] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-wl12xx[0]' [1.043487] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-wl12xx[0]' - status (0) [4.151885] wl12xx_driver wl12xx.1.auto: Direct firmware load for ti-connectivity/wl128x-nvs.bin failed with error -2 [ 11.368286] vwl1271: disabling root@devuan:/home/user# find /lib/firmware/ | grep wl128 /lib/firmware/ti-connectivity/wl128x-fw-5-plt.bin /lib/firmware/ti-connectivity/wl128x-fw-5-mr.bin /lib/firmware/ti-connectivity/wl128x-fw-5-sr.bin /lib/firmware/ti-connectivity/wl128x-nvs.bin root@devuan:/home/user# Ideas welcome... ... ... am I supposed to compile wl128-nvs.bin into the kernel using EXTRA_FIRMWARE? Pavel > Merry Christmas! > > -- Sebastian > > Sebastian Reichel (14): > ARM: dts: LogicPD Torpedo: Add WiLink UART node > ARM: dts: IGEP: Add WiLink UART node > ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support > media: wl128x-radio: remove module version > media: wl128x-radio: remove global radio_disconnected > media: wl128x-radio: remove global radio_dev > media: wl128x-radio: convert to platform device > media: wl128x-radio: use device managed memory allocation > media: wl128x-radio: load firmware from ti-connectivity/ > media: wl128x-radio: simplify fmc_prepare/fmc_release > media: wl128x-radio: fix skb debug printing > media: wl128x-radio: move from TI_ST to hci_ll driver > Bluetooth: btwilink: drop superseded driver > misc: ti-st: Drop superseded driver > > .../boot/dts/logicpd-torpedo-37xx-devkit.dts | 8 + > arch/arm/boot/dts/omap3-igep0020-rev-f.dts| 8 + > arch/arm/boot/dts/omap3-igep0030-rev-g.dts| 8 + > arch/arm/mach-omap2/pdata-quirks.c| 52 - > drivers/bluetooth/Kconfig | 11 - > drivers/bluetooth/Makefile| 1 - > drivers/bluetooth/btwilink.c | 350 --- > drivers/bluetooth/hci_ll.c| 115 ++- > drivers/media/radio/wl128x/Kconfig| 2 +- > drivers/media/radio/wl128x/fmdrv.h| 5 +- > drivers/media/radio/wl128x/fmdrv_common.c | 211 ++-- > drivers/media/radio/wl128x/fmdrv_common.h | 4 +- > drivers/media/radio/wl128x/fmdrv_v4l2.c | 55 +- > drivers/media/radio/wl128x/fmdrv_v4l2.h | 2 +- > drivers/misc/Kconfig | 1 - > drivers/misc/Makefile | 1 - > drivers/misc/ti-st/Kconfig| 18 - > drivers/misc/ti-st/Makefile | 6 - > drivers/misc/ti-st/st_core.c | 922 -- > drivers/misc/ti-st/st_kim.c | 868 - > drivers/misc/ti-st/st_ll.c| 169 > include/linux/ti_wilink_st.h | 337 +-- > 22 files changed, 213 insertions(+), 2941 deletions(-) > delete mode 100644 drivers/bluetooth/btwilink.c > delete mode 100644 drivers/misc/ti-st/Kconfig > delete mode 100644 drivers/misc/ti-st/Makefile > delete mode 100644 drivers/misc/ti-st/st_core.c > delete mode 100644 drivers/misc/ti-st/st_kim.c > delete mode 100644 drivers/misc/ti-st/st_ll.c > -- (english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html signature.asc Description: Digital signature
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Hi, On Fri, Dec 21, 2018 at 10:02:05AM -0800, Tony Lindgren wrote: > * Sebastian Reichel [181221 01:18]: > > The new code has been tested on the Motorola Droid 4. For testing the audio > > should be configured to route Ext to Speaker or Headphone. Then you need to > > plug headphone, since its cable is used as antenna. For testing there is a > > 'radio' utility packages in Debian. When you start the utility you need to > > specify a frequency, since initial get_frequency returns an error: > > Nice, good to see that ti-st kim stuff gone :) I gave this a quick > try using fmtools.git and fmscan works just fine. No luck yet with > fm though, it gives VIDIOC_G_CTRL: Not a tty error somehow so > maybe I'm missing some options, patch below for omap2plus_defconfig. I only did a few quick tests with 'radio' utility. I could scan for stations and I could listen to some station. I suppose the wl128x-radio driver has some buggy code paths, but that are unrelated to this patchset. > Hmm so looks like nothing to configure for the clocks or > CPCAP_BIT_ST_L_TIMESLOT bits for cap for the EXT? So the > wl12xx audio is wired directly to cpcap EXT then and not a > TDM slot on the mcbsp huh? For FM radio it's directly wired to EXT with no DAI being required. I think that EXT is only used by FM radio and not by bluetooth. BT seems to use TDM. > > Merry Christmas! > > Same to you! > > Tony > > 8< > From tony Mon Sep 17 00:00:00 2001 > From: Tony Lindgren > Date: Fri, 21 Dec 2018 07:57:09 -0800 > Subject: [PATCH] ARM: omap2plus_defconfig: Add RADIO_WL128X as a loadable > module > > This allows using the FM radio in the wl12xx chips after modprobe > fm_drv using radio from xawt, or fmtools. Mh. I suppose I forgot to add alias to support autoloading the FM module. > Note that the firmware placed into /lib/firmware/ti-connectivity > directory: > > fm_rx_ch8_1283.2.bts > fmc_ch8_1283.2.bts There is also a TX firmware. The Droid 4's chip should support this, but I don't know if there is audio routing for this feature. -- Sebastian > Signed-off-by: Tony Lindgren > --- > arch/arm/configs/omap2plus_defconfig | 3 +++ > 1 file changed, 3 insertions(+) > > diff --git a/arch/arm/configs/omap2plus_defconfig > b/arch/arm/configs/omap2plus_defconfig > --- a/arch/arm/configs/omap2plus_defconfig > +++ b/arch/arm/configs/omap2plus_defconfig > @@ -126,6 +126,7 @@ CONFIG_AF_RXRPC=m > CONFIG_RXKAD=y > CONFIG_CFG80211=m > CONFIG_MAC80211=m > +CONFIG_RFKILL=m > CONFIG_DEVTMPFS=y > CONFIG_DEVTMPFS_MOUNT=y > CONFIG_DMA_CMA=y > @@ -343,12 +344,14 @@ CONFIG_IR_GPIO_TX=m > CONFIG_IR_PWM_TX=m > CONFIG_MEDIA_SUPPORT=m > CONFIG_MEDIA_CAMERA_SUPPORT=y > +CONFIG_MEDIA_RADIO_SUPPORT=y > CONFIG_MEDIA_CEC_SUPPORT=y > CONFIG_MEDIA_CONTROLLER=y > CONFIG_VIDEO_V4L2_SUBDEV_API=y > CONFIG_V4L_PLATFORM_DRIVERS=y > CONFIG_VIDEO_OMAP3=m > CONFIG_CEC_PLATFORM_DRIVERS=y > +CONFIG_RADIO_WL128X=m > # CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set > CONFIG_VIDEO_TVP5150=m > CONFIG_DRM=m > -- > 2.19.2 signature.asc Description: PGP signature
Re: [PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
* Sebastian Reichel [181221 01:18]: > The new code has been tested on the Motorola Droid 4. For testing the audio > should be configured to route Ext to Speaker or Headphone. Then you need to > plug headphone, since its cable is used as antenna. For testing there is a > 'radio' utility packages in Debian. When you start the utility you need to > specify a frequency, since initial get_frequency returns an error: Nice, good to see that ti-st kim stuff gone :) I gave this a quick try using fmtools.git and fmscan works just fine. No luck yet with fm though, it gives VIDIOC_G_CTRL: Not a tty error somehow so maybe I'm missing some options, patch below for omap2plus_defconfig. Hmm so looks like nothing to configure for the clocks or CPCAP_BIT_ST_L_TIMESLOT bits for cap for the EXT? So the wl12xx audio is wired directly to cpcap EXT then and not a TDM slot on the mcbsp huh? > Merry Christmas! Same to you! Tony 8< >From tony Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 21 Dec 2018 07:57:09 -0800 Subject: [PATCH] ARM: omap2plus_defconfig: Add RADIO_WL128X as a loadable module This allows using the FM radio in the wl12xx chips after modprobe fm_drv using radio from xawt, or fmtools. Note that the firmware placed into /lib/firmware/ti-connectivity directory: fm_rx_ch8_1283.2.bts fmc_ch8_1283.2.bts Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -126,6 +126,7 @@ CONFIG_AF_RXRPC=m CONFIG_RXKAD=y CONFIG_CFG80211=m CONFIG_MAC80211=m +CONFIG_RFKILL=m CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y CONFIG_DMA_CMA=y @@ -343,12 +344,14 @@ CONFIG_IR_GPIO_TX=m CONFIG_IR_PWM_TX=m CONFIG_MEDIA_SUPPORT=m CONFIG_MEDIA_CAMERA_SUPPORT=y +CONFIG_MEDIA_RADIO_SUPPORT=y CONFIG_MEDIA_CEC_SUPPORT=y CONFIG_MEDIA_CONTROLLER=y CONFIG_VIDEO_V4L2_SUBDEV_API=y CONFIG_V4L_PLATFORM_DRIVERS=y CONFIG_VIDEO_OMAP3=m CONFIG_CEC_PLATFORM_DRIVERS=y +CONFIG_RADIO_WL128X=m # CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set CONFIG_VIDEO_TVP5150=m CONFIG_DRM=m -- 2.19.2
[PATCH 00/14] Add support for FM radio in hcill and kill TI_ST
Hi, This moves all remaining users of the legacy TI_ST driver to hcill (patches 1-3). Then patches 4-7 convert wl128x-radio driver to a standard platform device driver with support for multiple instances. Patch 7 will result in (userless) TI_ST driver no longer supporting radio at runtime. Patch 8-11 do some cleanups in the wl128x-radio driver. Finally patch 12 removes the TI_ST specific parts from wl128x-radio and adds the required infrastructure to use it with the serdev hcill driver instead. The remaining patches 13 and 14 remove the old TI_ST code. The new code has been tested on the Motorola Droid 4. For testing the audio should be configured to route Ext to Speaker or Headphone. Then you need to plug headphone, since its cable is used as antenna. For testing there is a 'radio' utility packages in Debian. When you start the utility you need to specify a frequency, since initial get_frequency returns an error: $ radio -f 100.0 Merry Christmas! -- Sebastian Sebastian Reichel (14): ARM: dts: LogicPD Torpedo: Add WiLink UART node ARM: dts: IGEP: Add WiLink UART node ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support media: wl128x-radio: remove module version media: wl128x-radio: remove global radio_disconnected media: wl128x-radio: remove global radio_dev media: wl128x-radio: convert to platform device media: wl128x-radio: use device managed memory allocation media: wl128x-radio: load firmware from ti-connectivity/ media: wl128x-radio: simplify fmc_prepare/fmc_release media: wl128x-radio: fix skb debug printing media: wl128x-radio: move from TI_ST to hci_ll driver Bluetooth: btwilink: drop superseded driver misc: ti-st: Drop superseded driver .../boot/dts/logicpd-torpedo-37xx-devkit.dts | 8 + arch/arm/boot/dts/omap3-igep0020-rev-f.dts| 8 + arch/arm/boot/dts/omap3-igep0030-rev-g.dts| 8 + arch/arm/mach-omap2/pdata-quirks.c| 52 - drivers/bluetooth/Kconfig | 11 - drivers/bluetooth/Makefile| 1 - drivers/bluetooth/btwilink.c | 350 --- drivers/bluetooth/hci_ll.c| 115 ++- drivers/media/radio/wl128x/Kconfig| 2 +- drivers/media/radio/wl128x/fmdrv.h| 5 +- drivers/media/radio/wl128x/fmdrv_common.c | 211 ++-- drivers/media/radio/wl128x/fmdrv_common.h | 4 +- drivers/media/radio/wl128x/fmdrv_v4l2.c | 55 +- drivers/media/radio/wl128x/fmdrv_v4l2.h | 2 +- drivers/misc/Kconfig | 1 - drivers/misc/Makefile | 1 - drivers/misc/ti-st/Kconfig| 18 - drivers/misc/ti-st/Makefile | 6 - drivers/misc/ti-st/st_core.c | 922 -- drivers/misc/ti-st/st_kim.c | 868 - drivers/misc/ti-st/st_ll.c| 169 include/linux/ti_wilink_st.h | 337 +-- 22 files changed, 213 insertions(+), 2941 deletions(-) delete mode 100644 drivers/bluetooth/btwilink.c delete mode 100644 drivers/misc/ti-st/Kconfig delete mode 100644 drivers/misc/ti-st/Makefile delete mode 100644 drivers/misc/ti-st/st_core.c delete mode 100644 drivers/misc/ti-st/st_kim.c delete mode 100644 drivers/misc/ti-st/st_ll.c -- 2.19.2
