Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On 9/4/18 8:57 PM, Saravanan Sekar wrote: On 08/29/18 17:50, Manivannan Sadhasivam wrote: On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: Add pinctrl and pio bindings for Actions Semi S700 SoC. Signed-off-by: Parthiban Nallathambi Signed-off-by: Saravanan Sekar Reviewed-by: Rob Herring --- .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 + 1 file changed, 170 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt new file mode 100644 index ..ceed32e836b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt @@ -0,0 +1,170 @@ +Actions Semi S700 Pin Controller + +This binding describes the pin controller found in the S700 SoC. + +Required Properties: + +- compatible: Should be "actions,s700-pinctrl" +- reg: Should contain the register base address and size of + the pin controller. +- clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends + on the number of GPIO banks on the SoC. The interrupts must be + ordered by bank, starting with bank 0. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Pinmux functions are available only for the pin groups while pinconf +parameters are available for both pin groups and individual pins. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +Required Properties: + +- pins: An array of strings, each string containing the name of a pin. + These pins are used for selecting the pull control and schmitt + trigger parameters. The following are the list of pins + available: + + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, + csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2, + dnand_d3,
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On 9/4/18 8:57 PM, Saravanan Sekar wrote: On 08/29/18 17:50, Manivannan Sadhasivam wrote: On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: Add pinctrl and pio bindings for Actions Semi S700 SoC. Signed-off-by: Parthiban Nallathambi Signed-off-by: Saravanan Sekar Reviewed-by: Rob Herring --- .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 + 1 file changed, 170 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt new file mode 100644 index ..ceed32e836b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt @@ -0,0 +1,170 @@ +Actions Semi S700 Pin Controller + +This binding describes the pin controller found in the S700 SoC. + +Required Properties: + +- compatible: Should be "actions,s700-pinctrl" +- reg: Should contain the register base address and size of + the pin controller. +- clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends + on the number of GPIO banks on the SoC. The interrupts must be + ordered by bank, starting with bank 0. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Pinmux functions are available only for the pin groups while pinconf +parameters are available for both pin groups and individual pins. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +Required Properties: + +- pins: An array of strings, each string containing the name of a pin. + These pins are used for selecting the pull control and schmitt + trigger parameters. The following are the list of pins + available: + + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, + csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2, + dnand_d3,
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
ping on this patch series! On 9/4/18 8:57 PM, Saravanan Sekar wrote: On 08/29/18 17:50, Manivannan Sadhasivam wrote: On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: Add pinctrl and pio bindings for Actions Semi S700 SoC. Signed-off-by: Parthiban Nallathambi Signed-off-by: Saravanan Sekar Reviewed-by: Rob Herring --- .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 + 1 file changed, 170 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt new file mode 100644 index ..ceed32e836b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt @@ -0,0 +1,170 @@ +Actions Semi S700 Pin Controller + +This binding describes the pin controller found in the S700 SoC. + +Required Properties: + +- compatible: Should be "actions,s700-pinctrl" +- reg: Should contain the register base address and size of + the pin controller. +- clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends + on the number of GPIO banks on the SoC. The interrupts must be + ordered by bank, starting with bank 0. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Pinmux functions are available only for the pin groups while pinconf +parameters are available for both pin groups and individual pins. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +Required Properties: + +- pins: An array of strings, each string containing the name of a pin. + These pins are used for selecting the pull control and schmitt + trigger parameters. The following are the list of pins + available: + + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, + csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2, +
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
ping on this patch series! On 9/4/18 8:57 PM, Saravanan Sekar wrote: On 08/29/18 17:50, Manivannan Sadhasivam wrote: On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: Add pinctrl and pio bindings for Actions Semi S700 SoC. Signed-off-by: Parthiban Nallathambi Signed-off-by: Saravanan Sekar Reviewed-by: Rob Herring --- .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 + 1 file changed, 170 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt new file mode 100644 index ..ceed32e836b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt @@ -0,0 +1,170 @@ +Actions Semi S700 Pin Controller + +This binding describes the pin controller found in the S700 SoC. + +Required Properties: + +- compatible: Should be "actions,s700-pinctrl" +- reg: Should contain the register base address and size of + the pin controller. +- clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends + on the number of GPIO banks on the SoC. The interrupts must be + ordered by bank, starting with bank 0. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Pinmux functions are available only for the pin groups while pinconf +parameters are available for both pin groups and individual pins. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +Required Properties: + +- pins: An array of strings, each string containing the name of a pin. + These pins are used for selecting the pull control and schmitt + trigger parameters. The following are the list of pins + available: + + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, + csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2, +
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On 08/29/18 17:50, Manivannan Sadhasivam wrote: On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: Add pinctrl and pio bindings for Actions Semi S700 SoC. Signed-off-by: Parthiban Nallathambi Signed-off-by: Saravanan Sekar Reviewed-by: Rob Herring --- .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 + 1 file changed, 170 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt new file mode 100644 index ..ceed32e836b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt @@ -0,0 +1,170 @@ +Actions Semi S700 Pin Controller + +This binding describes the pin controller found in the S700 SoC. + +Required Properties: + +- compatible: Should be "actions,s700-pinctrl" +- reg: Should contain the register base address and size of + the pin controller. +- clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends + on the number of GPIO banks on the SoC. The interrupts must be + ordered by bank, starting with bank 0. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Pinmux functions are available only for the pin groups while pinconf +parameters are available for both pin groups and individual pins. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +Required Properties: + +- pins:An array of strings, each string containing the name of a pin. + These pins are used for selecting the pull control and schmitt + trigger parameters. The following are the list of pins + available: + + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, + csi_cn, csi_cp, csi_dn2, csi_dp2,
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On 08/29/18 17:50, Manivannan Sadhasivam wrote: On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: Add pinctrl and pio bindings for Actions Semi S700 SoC. Signed-off-by: Parthiban Nallathambi Signed-off-by: Saravanan Sekar Reviewed-by: Rob Herring --- .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 + 1 file changed, 170 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt new file mode 100644 index ..ceed32e836b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt @@ -0,0 +1,170 @@ +Actions Semi S700 Pin Controller + +This binding describes the pin controller found in the S700 SoC. + +Required Properties: + +- compatible: Should be "actions,s700-pinctrl" +- reg: Should contain the register base address and size of + the pin controller. +- clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends + on the number of GPIO banks on the SoC. The interrupts must be + ordered by bank, starting with bank 0. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Pinmux functions are available only for the pin groups while pinconf +parameters are available for both pin groups and individual pins. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +Required Properties: + +- pins:An array of strings, each string containing the name of a pin. + These pins are used for selecting the pull control and schmitt + trigger parameters. The following are the list of pins + available: + + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, + csi_cn, csi_cp, csi_dn2, csi_dp2,
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: > Add pinctrl and pio bindings for Actions Semi S700 SoC. > > Signed-off-by: Parthiban Nallathambi > Signed-off-by: Saravanan Sekar > Reviewed-by: Rob Herring > --- > .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 > + > 1 file changed, 170 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > > diff --git > a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > new file mode 100644 > index ..ceed32e836b1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > @@ -0,0 +1,170 @@ > +Actions Semi S700 Pin Controller > + > +This binding describes the pin controller found in the S700 SoC. > + > +Required Properties: > + > +- compatible: Should be "actions,s700-pinctrl" > +- reg: Should contain the register base address and size of > + the pin controller. > +- clocks: phandle of the clock feeding the pin controller > +- gpio-controller: Marks the device node as a GPIO controller. > +- gpio-ranges: Specifies the mapping between gpio controller and > + pin-controller pins. > +- #gpio-cells: Should be two. The first cell is the gpio pin number > + and the second cell is used for optional parameters. > +- interrupt-controller: Marks the device node as an interrupt controller. > +- #interrupt-cells: Specifies the number of cells needed to encode an > + interrupt. Shall be set to 2. The first cell > + defines the interrupt number, the second encodes > + the trigger flags described in > + bindings/interrupt-controller/interrupts.txt > +- interrupts: The interrupt outputs from the controller. There is one GPIO > + interrupt per GPIO bank. The number of interrupts listed > depends > + on the number of GPIO banks on the SoC. The interrupts must be > + ordered by bank, starting with bank 0. > + > +Please refer to pinctrl-bindings.txt in this directory for details of the > +common pinctrl bindings used by client devices, including the meaning of the > +phrase "pin configuration node". > + > +The pin configuration nodes act as a container for an arbitrary number of > +subnodes. Each of these subnodes represents some desired configuration for a > +pin, a group, or a list of pins or groups. This configuration can include the > +mux function to select on those group(s), and various pin configuration > +parameters, such as pull-up, drive strength, etc. > + > +PIN CONFIGURATION NODES: > + > +The name of each subnode is not important; all subnodes should be enumerated > +and processed purely based on their content. > + > +Each subnode only affects those parameters that are explicitly listed. In > +other words, a subnode that lists a mux function but no pin configuration > +parameters implies no information about any pin configuration parameters. > +Similarly, a pin subnode that describes a pullup parameter implies no > +information about e.g. the mux function. > + > +Pinmux functions are available only for the pin groups while pinconf > +parameters are available for both pin groups and individual pins. > + > +The following generic properties as defined in pinctrl-bindings.txt are valid > +to specify in a pin configuration subnode: > + > +Required Properties: > + > +- pins: An array of strings, each string containing the name of > a pin. > + These pins are used for selecting the pull control and schmitt > + trigger parameters. The following are the list of pins > + available: > + > + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, > + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, > + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, > + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, > + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, > + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, > + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, > + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, > + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, > + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, > + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, > + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, > + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, > + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, > + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, > + i2c1_sdata,
Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote: > Add pinctrl and pio bindings for Actions Semi S700 SoC. > > Signed-off-by: Parthiban Nallathambi > Signed-off-by: Saravanan Sekar > Reviewed-by: Rob Herring > --- > .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 > + > 1 file changed, 170 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > > diff --git > a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > new file mode 100644 > index ..ceed32e836b1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt > @@ -0,0 +1,170 @@ > +Actions Semi S700 Pin Controller > + > +This binding describes the pin controller found in the S700 SoC. > + > +Required Properties: > + > +- compatible: Should be "actions,s700-pinctrl" > +- reg: Should contain the register base address and size of > + the pin controller. > +- clocks: phandle of the clock feeding the pin controller > +- gpio-controller: Marks the device node as a GPIO controller. > +- gpio-ranges: Specifies the mapping between gpio controller and > + pin-controller pins. > +- #gpio-cells: Should be two. The first cell is the gpio pin number > + and the second cell is used for optional parameters. > +- interrupt-controller: Marks the device node as an interrupt controller. > +- #interrupt-cells: Specifies the number of cells needed to encode an > + interrupt. Shall be set to 2. The first cell > + defines the interrupt number, the second encodes > + the trigger flags described in > + bindings/interrupt-controller/interrupts.txt > +- interrupts: The interrupt outputs from the controller. There is one GPIO > + interrupt per GPIO bank. The number of interrupts listed > depends > + on the number of GPIO banks on the SoC. The interrupts must be > + ordered by bank, starting with bank 0. > + > +Please refer to pinctrl-bindings.txt in this directory for details of the > +common pinctrl bindings used by client devices, including the meaning of the > +phrase "pin configuration node". > + > +The pin configuration nodes act as a container for an arbitrary number of > +subnodes. Each of these subnodes represents some desired configuration for a > +pin, a group, or a list of pins or groups. This configuration can include the > +mux function to select on those group(s), and various pin configuration > +parameters, such as pull-up, drive strength, etc. > + > +PIN CONFIGURATION NODES: > + > +The name of each subnode is not important; all subnodes should be enumerated > +and processed purely based on their content. > + > +Each subnode only affects those parameters that are explicitly listed. In > +other words, a subnode that lists a mux function but no pin configuration > +parameters implies no information about any pin configuration parameters. > +Similarly, a pin subnode that describes a pullup parameter implies no > +information about e.g. the mux function. > + > +Pinmux functions are available only for the pin groups while pinconf > +parameters are available for both pin groups and individual pins. > + > +The following generic properties as defined in pinctrl-bindings.txt are valid > +to specify in a pin configuration subnode: > + > +Required Properties: > + > +- pins: An array of strings, each string containing the name of > a pin. > + These pins are used for selecting the pull control and schmitt > + trigger parameters. The following are the list of pins > + available: > + > + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, > + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, > + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, > + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, > + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, > + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, > + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, > + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, > + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, > + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, > + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, > + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, > + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, > + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, > + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, > + i2c1_sdata,
