Re: cx88 pci_abort errors (Hauppauge WinTV Nova-HD-S2)
On 06/05/2010 16:01, Thierry LELEGARD wrote: I recently added a Hauppauge WinTV Nova-HD-S2 into a Linux system. I experience frequent packet loss and pci_abort errors. Each time my application detects packet loss (continuity errors actually), I get the following messages in dmesg: cx88[0]: irq mpeg [0x8] pci_abort* cx88[0]/2-mpeg: general errors: 0x0008 Such problems occur every few seconds. I use firmware file dvb-fe-cx24116.fw version 1.26.90.0. Since the IRQ was shared with the nVidia card and a Dektec modulator, I swapped some PCI boards. The IRQ is still shared but with another Tuner I do not use when using the S2 tuner. After swapping the PCI boards, the errors occur less frequently but still happen. Assuming that the pci_abort was due to an interrupted DMA transfer, I tried to increase the PCI latency timer of the device to 248 but this did not change anything (setpci -s 05:05 latency_timer=f8). I use the tuner with a custom application which reads the complete Transport stream. This application had worked for years using DVB-T and DVB-S tuners. I tried to reduce the application read buffer input size and it did not change anything at all. Note that my application still uses the V3 API, not the S2API. But, using DVB-S transponders, it works (except the pci_abort errors). I disabled the serial port, the parallel port and the PS/2 ports in the BIOS. It did not change anything either. Does anyone have an idea, please? Thanks a lot in advance for any help. -Thierry I have the board working in a Ubuntu 9.10 system, log below shows no pci errors: Apr 21 18:32:11 antec300 kernel: [ 16.576416] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.7 loaded Apr 21 18:32:11 antec300 kernel: [ 16.576711] cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected], frontend(s): 1 Apr 21 18:32:11 antec300 kernel: [ 16.576714] cx88[0]: TV tuner type -1, Radio tuner type -1 Apr 21 18:32:11 antec300 kernel: [ 16.583565] cx88/0: cx2388x v4l2 driver version 0.0.7 loaded Apr 21 18:32:11 antec300 kernel: [ 16.586270] cx2388x alsa driver version 0.0.7 loaded Apr 21 18:32:11 antec300 kernel: [ 16.605679] EXT4-fs (sda1): internal journal on sda1:8 Apr 21 18:32:11 antec300 kernel: [ 16.755834] EXT4-fs (sdc1): barriers enabled Apr 21 18:32:11 antec300 kernel: [ 16.757791] kjournald2 starting: pid 956, dev sdc1:8, commit interval 5 seconds Apr 21 18:32:11 antec300 kernel: [ 16.763057] EXT4-fs (sdc1): internal journal on sdc1:8 Apr 21 18:32:11 antec300 kernel: [ 16.763061] EXT4-fs (sdc1): delayed allocation enabled Apr 21 18:32:11 antec300 kernel: [ 16.763063] EXT4-fs: file extents enabled Apr 21 18:32:11 antec300 kernel: [ 16.789147] EXT4-fs: mballoc enabled Apr 21 18:32:11 antec300 kernel: [ 16.789163] EXT4-fs (sdc1): mounted filesystem with ordered data mode Apr 21 18:32:11 antec300 kernel: [ 16.795868] tveeprom 2-0050: Hauppauge model 69100, rev B4C3, serial# 7084390 Apr 21 18:32:11 antec300 kernel: [ 16.795871] tveeprom 2-0050: MAC address is 00:0d:fe:6c:19:66 Apr 21 18:32:11 antec300 kernel: [ 16.795874] tveeprom 2-0050: tuner model is Conexant CX24118A (idx 123, type 4) Apr 21 18:32:11 antec300 kernel: [ 16.795876] tveeprom 2-0050: TV standards ATSC/DVB Digital (eeprom 0x80) Apr 21 18:32:11 antec300 kernel: [ 16.795878] tveeprom 2-0050: audio processor is None (idx 0) Apr 21 18:32:11 antec300 kernel: [ 16.795880] tveeprom 2-0050: decoder processor is CX880 (idx 20) Apr 21 18:32:11 antec300 kernel: [ 16.795882] tveeprom 2-0050: has no radio, has IR receiver, has no IR transmitter Apr 21 18:32:11 antec300 kernel: [ 16.795884] cx88[0]: hauppauge eeprom: model=69100 Apr 21 18:32:11 antec300 kernel: [ 16.798457] input: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci:00/:00:1e.0/:06:02.2/input/input6 Apr 21 18:32:11 antec300 kernel: [ 16.798488] cx88[0]/2: cx2388x 8802 Driver Manager Apr 21 18:32:11 antec300 kernel: [ 16.798500] cx88-mpeg driver manager :06:02.2: PCI INT A - GSI 19 (level, low) - IRQ 19 Apr 21 18:32:11 antec300 kernel: [ 16.798506] cx88[0]/2: found at :06:02.2, rev: 5, irq: 19, latency: 32, mmio: 0xf800 Apr 21 18:32:11 antec300 kernel: [ 16.798510] IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs Apr 21 18:32:11 antec300 kernel: [ 16.799143] cx8800 :06:02.0: PCI INT A - GSI 19 (level, low) - IRQ 19 Apr 21 18:32:11 antec300 kernel: [ 16.799151] cx88[0]/0: found at :06:02.0, rev: 5, irq: 19, latency: 32, mmio: 0xfa00 Apr 21 18:32:11 antec300 kernel: [ 16.799158] IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs Apr 21 18:32:11 antec300 kernel: [ 16.799193] cx88[0]/0: registered device video0 [v4l2] Apr 21 18:32:11 antec300 kernel: [ 16.799210] cx88[0]/0: registered device vbi0 Apr 21 18:32:11 antec300 kernel: [ 16.802095] cx88_audio :06:02.1: PCI INT A - GSI 19 (level, low) - IRQ 19 Apr
Fwd: Re: setting up a tevii s660
On 06/05/2010 00:07, Tim Coote wrote: Hullo I've been struggling with this for a couple of days. I have checked archives, but missed anything useful. I've got a tevii s660 (dvbs2 via usb). It works with some limitations on windows xp (I cannot get HD signals decoded, but think that's a limitation of the software that comes on the CD). I downloaded version from tevii.com and it worked for me on laptop running win 7. Had problems with HD on an XP machine but I assumed it was because the video card was old/slow. I'm trying to get this working on Linux. I've tried VMs based on fedora 12 and mythbuntu (VMWare Fusion on a MacBookPro, both based on kernel 2.6.32), using the drivers from tevii's site (www.tevii.com/support.asp). these drivers are slightly modified versions of the v4l tip - but don't appear to be modified where I've not yet managed to get the drivers working :-(. Mythbuntu seems to be closest to working. Goodness knows how tevii tested the code, but it doesn't seem to work as far as I can see. My issues could just be down to using a VM. I tried on Ubuntu 9.10 but had problems which I documented here on 16 april. Loading the firmware worked fine but there were problems with remote control messages being logged continually as well as stability problems. The card would tune (with scan) and worked with mythtv (for a day or so) I believe that I need to load up the modules ds3000 and dvb-usb-dw2102, + add a rule to /etc/udev/rules.d and a script to /etc/udev/scripts. I didn't touch rules.d I think that I must be missing quite a lot of context, tho'. When I look at the code in dw2102.c, which seems to support the s660, the bit that downloads the firmware looks broken and if I add a default clause to the switch that does the download, the s660's missed the download process. This could be why when I do get anything out of the device it looks like I'm just getting repeated bytes (the same value repeated, different values at different times, sometimes nothing). I'm finding it non-trivial working out the call sequences of the code or devising repeatable tests. Had no problem with Ubuntu recognising the device and the correct .fw file being downloaded. There are various versions of dw2102.c from tevii, etc. I think I tried all of them. I did change the timeout on RC messages (dw2102.c?) which helped but did not cure the problem. Also tried the s2-liplianin library as well which seemed promising but also did not cure the problem. Can anyone kick me off on getting this working? I'd like to at least get to the point where scandvb can tune the device. It does look like some folk have had success in the past, but probably with totally different codebase (there are posts that refer to the teviis660 module, which I cannot find). Any pointer gratefully accepted. I'll feed back any success if I can be pointed at where to drop document it. I didn't have the knowledge (or time) to decide if the problem was in the firmware or the v4l drivers or perhaps some strange interaction with my dvb-t usb box. Exchanged some emails with tevii guys who had posted here however they appear to take the view that if it works under windows then the device is fine and offer no other solution. In the end I bought a Nova S2 PCI card which works fine but would be interested in trying to get the S660 working. paul -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: Fwd: Tevii S660 USB card and dw2102 module generating RC messages
On 18/04/2010 08:19, william wrote: Hello Paul, I know what is happening but i have no solution. The message: dw2102: query RC enter is a message from the ir receiver in the device. I noticed by accident that when you push some buttons on the remote (which came with the tevii box) while tailing the log file you will see the buttons on the remote. i'm not sure because my device did not work at all so i send it back to my supplier but i think the lib-s2planin drivers could fix it but i had no chance to test it myself. If you are going to try the s2planin drivers please let me know how it works! With kind regards William I also discovered that RC is remote control. Tried the v4l-dvb in various combos which looked promising for a period but usually ended up with either the s660 or my nova dvb-t usb flooding the system and rendering the usb keyboard unsable. Tried increasing the query time on the RC which seemed to help but still had problems. Then tried s2-liplianin code at your suggestion which looked promising but it was strangely requesting a 2nd upload dvb-fe-ds3000.fw which although present in /lib/firmware didn't occur. Later it crashed: Apr 18 23:23:12 antec300 kernel: [ 324.866653] usb 1-1: new high speed USB device using ehci_hcd and address 4 Apr 18 23:23:12 antec300 kernel: [ 325.458058] usb 1-1: new high speed USB device using ehci_hcd and address 5 Apr 18 23:23:12 antec300 kernel: [ 325.590133] usb 1-1: configuration #1 chosen from 1 choice Apr 18 23:23:12 antec300 kernel: [ 325.590330] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware Apr 18 23:23:12 antec300 kernel: [ 325.590339] usb 1-1: firmware: requesting dvb-usb-s660.fw Apr 18 23:23:12 antec300 kernel: [ 325.595031] dvb-usb: downloading firmware from file 'dvb-usb-s660.fw' Apr 18 23:23:12 antec300 kernel: [ 325.595037] dw2102: start downloading DW210X firmware Apr 18 23:23:12 antec300 kernel: [ 325.713426] dvb-usb: found a 'TeVii S660 USB' in warm state. Apr 18 23:23:12 antec300 kernel: [ 325.713479] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Apr 18 23:23:12 antec300 kernel: [ 325.717592] DVB: registering new adapter (TeVii S660 USB) Apr 18 23:23:18 antec300 kernel: [ 331.716487] dvb-usb: MAC address: 00:00:a0:00:00:00 Apr 18 23:23:18 antec300 kernel: [ 331.780801] input: IR-receiver inside an USB DVB receiver as /devices/pci:00/:00:1a.7/usb1/1-1/input/input7 Apr 18 23:23:18 antec300 kernel: [ 331.780862] dvb-usb: schedule remote query interval to 150 msecs. Apr 18 23:23:18 antec300 kernel: [ 331.780866] dvb-usb: TeVii S660 USB successfully initialized and connected. Apr 18 23:23:18 antec300 kernel: [ 331.780905] usb 1-1: USB disconnect, address 5 Apr 18 23:23:18 antec300 kernel: [ 331.813419] dvb-usb: TeVii S660 USB successfully deinitialized and disconnected. Apr 18 23:23:19 antec300 kernel: [ 332.051995] usb 1-1: new high speed USB device using ehci_hcd and address 6 Apr 18 23:23:19 antec300 kernel: [ 332.184522] usb 1-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 2 Apr 18 23:23:19 antec300 kernel: [ 332.185114] usb 1-1: configuration #1 chosen from 1 choice Apr 18 23:23:19 antec300 kernel: [ 332.185298] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware Apr 18 23:23:19 antec300 kernel: [ 332.185304] usb 1-1: firmware: requesting dvb-usb-s660.fw Apr 18 23:23:19 antec300 kernel: [ 332.190277] dvb-usb: downloading firmware from file 'dvb-usb-s660.fw' Apr 18 23:23:19 antec300 kernel: [ 332.190282] dw2102: start downloading DW210X firmware Apr 18 23:23:19 antec300 kernel: [ 332.307623] dvb-usb: found a 'TeVii S660 USB' in warm state. Apr 18 23:23:19 antec300 kernel: [ 332.307676] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Apr 18 23:23:19 antec300 kernel: [ 332.307818] DVB: registering new adapter (TeVii S660 USB) Apr 18 23:23:23 antec300 kernel: [ 336.413508] dvb-usb: MAC address: 00:18:bd:5c:60:b0 Apr 18 23:23:23 antec300 kernel: [ 336.462191] DS3000 chip version: 0.192 attached. Apr 18 23:23:23 antec300 kernel: [ 336.462195] dw2102: Attached ds3000+ds2020! Apr 18 23:23:23 antec300 kernel: [ 336.462197] Apr 18 23:23:23 antec300 kernel: [ 336.462202] DVB: registering adapter 1 frontend 0 (Montage Technology DS3000/TS2020)... Apr 18 23:23:23 antec300 kernel: [ 336.463198] input: IR-receiver inside an USB DVB receiver as /devices/pci:00/:00:1a.7/usb1/1-1/input/input8 Apr 18 23:23:23 antec300 kernel: [ 336.463244] dvb-usb: schedule remote query interval to 150 msecs. Apr 18 23:23:23 antec300 kernel: [ 336.463250] dvb-usb: TeVii S660 USB successfully initialized and connected. Apr 18 23:24:00 antec300 kernel: [ 373.534616] ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)... Apr 18 23:24:00 antec300 kernel: [ 373.534625] usb 1-1: firmware: requesting
Fwd: Tevii S660 USB card and dw2102 module generating RC messages
I have a Tevii S660 (a usb dvb-s2 device) which is causing a problem. After the S660 is attached to a USB 2 socket, the firmware is d/l and everything looks fine but then there are continual RC (check/debug?) messages every 150 ms, then some time later everything goes pear shaped: Apr 9 22:15:49 antec300 kernel: [ 16.801141] EXT3 FS on sdd1, internal journal Apr 9 22:15:49 antec300 kernel: [ 16.801144] EXT3-fs: mounted filesystem with writeback data mode. Apr 9 22:15:49 antec300 kernel: [ 17.490262] hda-intel: Codec #3 probe error; disabling it... Apr 9 22:15:50 antec300 kernel: [ 17.568264] hda_codec: Unknown model for ALC889, trying auto-probe from BIOS... Apr 9 22:15:50 antec300 kernel: [ 17.568513] input: HDA Digital PCBeep as /devices/pci:00/:00:1b.0/input/input6 Apr 9 22:15:55 antec300 kernel: [ 22.697708] __ratelimit: 24 callbacks suppressed Apr 9 22:15:55 antec300 kernel: [ 22.697711] type=1503 audit(1270847755.406:33): operation=open pid=2328 parent=1870 profile=/usr/sbin/mysqld requested_mask=::r denied_mask=::r fsuid=119 ouid=0 name=/sys/devices/system/cpu/ . # plug the S660 in ... . Apr 9 22:24:52 antec300 kernel: [ 559.078860] usb 1-1: new high speed USB device using ehci_hcd and address 7 Apr 9 22:24:52 antec300 kernel: [ 559.211222] usb 1-1: configuration #1 chosen from 1 choice Apr 9 22:24:52 antec300 kernel: [ 559.211390] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware Apr 9 22:24:52 antec300 kernel: [ 559.211396] usb 1-1: firmware: requesting dvb-usb-teviis660.fw Apr 9 22:24:52 antec300 kernel: [ 559.224426] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw' Apr 9 22:24:52 antec300 kernel: [ 559.224431] dw2102: start downloading DW210X firmware Apr 9 22:24:52 antec300 kernel: [ 559.342492] dvb-usb: found a 'TeVii S660 USB' in warm state. Apr 9 22:24:52 antec300 kernel: [ 559.342561] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Apr 9 22:24:52 antec300 kernel: [ 559.346560] DVB: registering new adapter (TeVii S660 USB) Apr 9 22:24:58 antec300 kernel: [ 565.369380] dvb-usb: MAC address: d0:d0:d0:d0:d0:d0 Apr 9 22:24:58 antec300 kernel: [ 565.394061] Only Zarlink VP310/MT312/ZL10313 are supported chips. Apr 9 22:24:59 antec300 kernel: [ 565.665303] input: IR-receiver inside an USB DVB receiver as /devices/pci:00/:00:1a.7/usb1/1-1/input/input11 Apr 9 22:24:59 antec300 kernel: [ 565.665361] dvb-usb: schedule remote query interval to 150 msecs. Apr 9 22:24:59 antec300 kernel: [ 565.665366] dvb-usb: TeVii S660 USB successfully initialized and connected. Apr 9 22:24:59 antec300 kernel: [ 565.665817] usb 1-1: USB disconnect, address 7 Apr 9 22:24:59 antec300 kernel: [ 565.693209] dvb-usb: TeVii S660 USB successfully deinitialized and disconnected. Apr 9 22:24:59 antec300 kernel: [ 565.932522] usb 1-1: new high speed USB device using ehci_hcd and address 8 Apr 9 22:24:59 antec300 kernel: [ 566.064970] usb 1-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 2 Apr 9 22:24:59 antec300 kernel: [ 566.065590] usb 1-1: configuration #1 chosen from 1 choice Apr 9 22:24:59 antec300 kernel: [ 566.066164] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware Apr 9 22:24:59 antec300 kernel: [ 566.066171] usb 1-1: firmware: requesting dvb-usb-teviis660.fw Apr 9 22:24:59 antec300 kernel: [ 566.072788] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw' Apr 9 22:24:59 antec300 kernel: [ 566.072792] dw2102: start downloading DW210X firmware Apr 9 22:24:59 antec300 kernel: [ 566.192150] dvb-usb: found a 'TeVii S660 USB' in warm state. Apr 9 22:24:59 antec300 kernel: [ 566.192213] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Apr 9 22:24:59 antec300 kernel: [ 566.192644] DVB: registering new adapter (TeVii S660 USB) Apr 9 22:25:03 antec300 kernel: [ 570.298170] dvb-usb: MAC address: 00:18:bd:5c:60:b0 Apr 9 22:25:03 antec300 kernel: [ 570.314148] Only Zarlink VP310/MT312/ZL10313 are supported chips. Apr 9 22:25:04 antec300 kernel: [ 570.589497] DS3000 chip version: 0.192 attached. Apr 9 22:25:04 antec300 kernel: [ 570.589501] dw2102: Attached ds3000+ds2020! Apr 9 22:25:04 antec300 kernel: [ 570.589503] Apr 9 22:25:04 antec300 kernel: [ 570.589707] DVB: registering adapter 1 frontend 0 (Montage Technology DS3000/TS2020)... Apr 9 22:25:04 antec300 kernel: [ 570.590909] input: IR-receiver inside an USB DVB receiver as /devices/pci:00/:00:1a.7/usb1/1-1/input/input12 Apr 9 22:25:04 antec300 kernel: [ 570.590965] dvb-usb: schedule remote query interval to 150 msecs. Apr 9 22:25:04 antec300 kernel: [ 570.590971] dvb-usb: TeVii S660 USB successfully initialized and connected. Apr 9 22:25:04 antec300 kernel: [ 570.741992] dw2102: query RC enter Apr 9 22:25:04 antec300 kernel: [ 570.741996]
Re: Fwd: Tevii S660 USB card and dw2102 module generating RC messages
Josu, mythtv version 0.22-fixes [22594] however I don't think it's mythtv problem but an interaction somewhere between the S660 h/w, firmware and the kernel (vl4-dvb etc) paul On 16/04/2010 10:34, Josu Lazkano wrote: Which version of mythtv are you using? Josu Lazkano El 16/04/2010 10:58, Paul Shepherd p...@whitelands.org.uk mailto:p...@whitelands.org.uk escribió: I have a Tevii S660 (a usb dvb-s2 device) which is causing a problem. After the S660 is attached to a USB 2 socket, the firmware is d/l and everything looks fine but then there are continual RC (check/debug?) messages every 150 ms, then some time later everything goes pear shaped: Apr 9 22:15:49 antec300 kernel: [ 16.801141] EXT3 FS on sdd1, internal journal Apr 9 22:15:49 antec300 kernel: [ 16.801144] EXT3-fs: mounted filesystem with writeback data mode. Apr 9 22:15:49 antec300 kernel: [ 17.490262] hda-intel: Codec #3 probe error; disabling it... Apr 9 22:15:50 antec300 kernel: [ 17.568264] hda_codec: Unknown model for ALC889, trying auto-probe from BIOS... Apr 9 22:15:50 antec300 kernel: [ 17.568513] input: HDA Digital PCBeep as /devices/pci:00/:00:1b.0/input/input6 Apr 9 22:15:55 antec300 kernel: [ 22.697708] __ratelimit: 24 callbacks suppressed Apr 9 22:15:55 antec300 kernel: [ 22.697711] type=1503 audit(1270847755.406:33): operation=open pid=2328 parent=1870 profile=/usr/sbin/mysqld requested_mask=::r denied_mask=::r fsuid=119 ouid=0 name=/sys/devices/system/cpu/ . # plug the S660 in ... . Apr 9 22:24:52 antec300 kernel: [ 559.078860] usb 1-1: new high speed USB device using ehci_hcd and address 7 Apr 9 22:24:52 antec300 kernel: [ 559.211222] usb 1-1: configuration #1 chosen from 1 choice Apr 9 22:24:52 antec300 kernel: [ 559.211390] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware Apr 9 22:24:52 antec300 kernel: [ 559.211396] usb 1-1: firmware: requesting dvb-usb-teviis660.fw Apr 9 22:24:52 antec300 kernel: [ 559.224426] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw' Apr 9 22:24:52 antec300 kernel: [ 559.224431] dw2102: start downloading DW210X firmware Apr 9 22:24:52 antec300 kernel: [ 559.342492] dvb-usb: found a 'TeVii S660 USB' in warm state. Apr 9 22:24:52 antec300 kernel: [ 559.342561] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Apr 9 22:24:52 antec300 kernel: [ 559.346560] DVB: registering new adapter (TeVii S660 USB) Apr 9 22:24:58 antec300 kernel: [ 565.369380] dvb-usb: MAC address: d0:d0:d0:d0:d0:d0 Apr 9 22:24:58 antec300 kernel: [ 565.394061] Only Zarlink VP310/MT312/ZL10313 are supported chips. Apr 9 22:24:59 antec300 kernel: [ 565.665303] input: IR-receiver inside an USB DVB receiver as /devices/pci:00/:00:1a.7/usb1/1-1/input/input11 Apr 9 22:24:59 antec300 kernel: [ 565.665361] dvb-usb: schedule remote query interval to 150 msecs. Apr 9 22:24:59 antec300 kernel: [ 565.665366] dvb-usb: TeVii S660 USB successfully initialized and connected. Apr 9 22:24:59 antec300 kernel: [ 565.665817] usb 1-1: USB disconnect, address 7 Apr 9 22:24:59 antec300 kernel: [ 565.693209] dvb-usb: TeVii S660 USB successfully deinitialized and disconnected. Apr 9 22:24:59 antec300 kernel: [ 565.932522] usb 1-1: new high speed USB device using ehci_hcd and address 8 Apr 9 22:24:59 antec300 kernel: [ 566.064970] usb 1-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 2 Apr 9 22:24:59 antec300 kernel: [ 566.065590] usb 1-1: configuration #1 chosen from 1 choice Apr 9 22:24:59 antec300 kernel: [ 566.066164] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware Apr 9 22:24:59 antec300 kernel: [ 566.066171] usb 1-1: firmware: requesting dvb-usb-teviis660.fw Apr 9 22:24:59 antec300 kernel: [ 566.072788] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw' Apr 9 22:24:59 antec300 kernel: [ 566.072792] dw2102: start downloading DW210X firmware Apr 9 22:24:59 antec300 kernel: [ 566.192150] dvb-usb: found a 'TeVii S660 USB' in warm state. Apr 9 22:24:59 antec300 kernel: [ 566.192213] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Apr 9 22:24:59 antec300 kernel: [ 566.192644] DVB: registering new adapter (TeVii S660 USB) Apr 9 22:25:03 antec300 kernel: [ 570.298170] dvb-usb: MAC address: 00:18:bd:5c:60:b0 Apr 9 22:25:03 antec300 kernel: [ 570.314148] Only Zarlink VP310/MT312/ZL10313 are supported chips. Apr 9 22:25:04 antec300 kernel: [ 570.589497] DS3000 chip version: 0.192 attached. Apr 9 22:25:04 antec300 kernel: [ 570.589501] dw2102: Attached ds3000+ds2020
