On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.

For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.

Read speed increases from 16516 KiB/ to 18813 KiB/s
and write speed was unchanged at 9941 KiB/s.

Measured using mtd_speedtest.ko.

Signed-off-by: Roger Quadros <rog...@ti.com>
---
 arch/arm/boot/dts/am437x-gp-evm.dts  | 3 +--
 arch/arm/boot/dts/am43x-epos-evm.dts | 3 +--
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts 
b/arch/arm/boot/dts/am437x-gp-evm.dts
index aa96c99..d7bfe9f 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -800,6 +800,7 @@
                reg = <0 0 4>;          /* device IO registers */
                interrupt-parent = <&gic>;
                interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+               ready-gpio = <&gpmc 0 GPIO_ACTIVE_HIGH>;        /* gpmc_wait0 */
                ti,nand-ecc-opt = "bch16";
                ti,elm-id = <&elm>;
                nand-bus-width = <8>;
@@ -818,11 +819,9 @@
                gpmc,access-ns = <30>;
                gpmc,rd-cycle-ns = <40>;
                gpmc,wr-cycle-ns = <40>;
-               gpmc,wait-pin = <0>;
                gpmc,bus-turnaround-ns = <0>;
                gpmc,cycle2cycle-delay-ns = <0>;
                gpmc,clk-activation-ns = <0>;
-               gpmc,wait-monitoring-ns = <0>;
                gpmc,wr-access-ns = <40>;
                gpmc,wr-data-mux-bus-ns = <0>;
                /* MTD partition table */
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts 
b/arch/arm/boot/dts/am43x-epos-evm.dts
index 9a7786d..4b26762 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -567,6 +567,7 @@
                reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
                interrupt-parent = <&gic>;
                interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+               ready-gpio = <&gpmc 0 GPIO_ACTIVE_HIGH>;        /* gpmc_wait0 */
                ti,nand-ecc-opt = "bch16";
                ti,elm-id = <&elm>;
                nand-bus-width = <8>;
@@ -585,11 +586,9 @@
                gpmc,access-ns = <30>; /* tCEA + 4*/
                gpmc,rd-cycle-ns = <40>;
                gpmc,wr-cycle-ns = <40>;
-               gpmc,wait-pin = <0>;
                gpmc,bus-turnaround-ns = <0>;
                gpmc,cycle2cycle-delay-ns = <0>;
                gpmc,clk-activation-ns = <0>;
-               gpmc,wait-monitoring-ns = <0>;
                gpmc,wr-access-ns = <40>;
                gpmc,wr-data-mux-bus-ns = <0>;
                /* MTD partition table */
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to