Re: [PATCH v3 3/5] [RFT] ARM: dts: wheat: Fix ADV7513 address usage

[Laurent Pinchart]

Hi Kieran,

Thank you for the patch.

On Tuesday, 13 February 2018 00:07:51 EET Kieran Bingham wrote:
> From: Kieran Bingham 
> 
> The r8a7792 Wheat board has two ADV7513 devices sharing a single i2c
> bus, however in low power mode the ADV7513 will reset it's slave maps to
> use the hardware defined default addresses.
> 
> The ADV7511 driver was adapted to allow the two devices to be registered
> correctly - but it did not take into account the fault whereby the
> devices reset the addresses.
> 
> This results in an address conflict between the device using the default
> addresses, and the other device if it is in low-power-mode.
> 
> Repair this issue by moving both devices away from the default address
> definitions.
> 
> Signed-off-by: Kieran Bingham 

Reviewed-by: Laurent Pinchart 

> ---
> v2:
>  - Addition to series
> 
> v3:
>  - Split map register addresses into individual declarations.
> 
>  arch/arm/boot/dts/r8a7792-wheat.dts | 12 ++--
>  1 file changed, 10 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts
> b/arch/arm/boot/dts/r8a7792-wheat.dts index b9471b67b728..42fff8837eab
> 100644
> --- a/arch/arm/boot/dts/r8a7792-wheat.dts
> +++ b/arch/arm/boot/dts/r8a7792-wheat.dts
> @@ -240,9 +240,16 @@
>   status = "okay";
>   clock-frequency = <40>;
> 
> + /*
> +  * The adv75xx resets its addresses to defaults during low power power
> +  * mode. Because we have two ADV7513 devices on the same bus, we must
> +  * change both of them away from the defaults so that they do not
> +  * conflict.
> +  */
>   hdmi@3d {
>   compatible = "adi,adv7513";
> - reg = <0x3d>;
> + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
> + reg-names = "main", "cec", "edid", "packet";
> 
>   adi,input-depth = <8>;
>   adi,input-colorspace = "rgb";
> @@ -272,7 +279,8 @@
> 
>   hdmi@39 {
>   compatible = "adi,adv7513";
> - reg = <0x39>;
> + reg = <0x39>, <0x29>, <0x49>, <0x59>;
> + reg-names = "main", "cec", "edid", "packet";
> 
>   adi,input-depth = <8>;
>   adi,input-colorspace = "rgb";

-- 
Regards,

Laurent Pinchart

[PATCH v3 3/5] [RFT] ARM: dts: wheat: Fix ADV7513 address usage

[Kieran Bingham]

From: Kieran Bingham 

The r8a7792 Wheat board has two ADV7513 devices sharing a single i2c
bus, however in low power mode the ADV7513 will reset it's slave maps to
use the hardware defined default addresses.

The ADV7511 driver was adapted to allow the two devices to be registered
correctly - but it did not take into account the fault whereby the
devices reset the addresses.

This results in an address conflict between the device using the default
addresses, and the other device if it is in low-power-mode.

Repair this issue by moving both devices away from the default address
definitions.

Signed-off-by: Kieran Bingham 

---
v2:
 - Addition to series

v3:
 - Split map register addresses into individual declarations.

 arch/arm/boot/dts/r8a7792-wheat.dts | 12 ++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts 
b/arch/arm/boot/dts/r8a7792-wheat.dts
index b9471b67b728..42fff8837eab 100644
--- a/arch/arm/boot/dts/r8a7792-wheat.dts
+++ b/arch/arm/boot/dts/r8a7792-wheat.dts
@@ -240,9 +240,16 @@
status = "okay";
clock-frequency = <40>;
 
+   /*
+* The adv75xx resets its addresses to defaults during low power power
+* mode. Because we have two ADV7513 devices on the same bus, we must
+* change both of them away from the defaults so that they do not
+* conflict.
+*/
hdmi@3d {
compatible = "adi,adv7513";
-   reg = <0x3d>;
+   reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
+   reg-names = "main", "cec", "edid", "packet";
 
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
@@ -272,7 +279,8 @@
 
hdmi@39 {
compatible = "adi,adv7513";
-   reg = <0x39>;
+   reg = <0x39>, <0x29>, <0x49>, <0x59>;
+   reg-names = "main", "cec", "edid", "packet";
 
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
-- 
2.7.4