Enable CONFIG_LEDS_PWM amd CONFIG_LEDS_TRIGGER_HEARTBEAT for
Odroid-XU3 board.
Signed-off-by: Anand Moon linux.am...@gmail.com
---
arch/arm/configs/exynos_defconfig | 6 ++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/configs/exynos_defconfig
b/arch/arm/configs/exynos_defconfig
Enable CONFIG_SND_SOC_ODROIDX2 and CONFIG_SND_SIMPLE_CARD to enable
sound on Odroid-XU3 board.
Below is the output of boot log.
[6.021550] max98090 5-0010: MAX98090 REVID=0x43
[6.025506] random: nonblocking pool is initialized
[6.047297] asoc-simple-card sound: HiFi - 383.i2s
Enable regulator for usbdrd3_0 and usbdrd3_1.
Looking at the schematic pin diagram for MAX77802
USB3_0 and USB3_1 is regulated by LDO9 and LD011.
Fix the boot message of failed.
[3.503539] exynos-dwc3 usb@1200: Looking up vdd33-supply from device
tree
[3.503556] exynos-dwc3
Facilitate getting required 3.3V and 1.0V VDD supply for
OHCI controller on Exynos.
With patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
the exynos systems turn on only minimal number of
Facilitate getting required 3.3V and 1.0V VDD supply for
EHCI controller on Exynos.
With the patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
the exynos systems turn on only minimal number of
2015-06-08 13:21 GMT+09:00 Anand Moon linux.am...@gmail.com:
Hi Krzysztof ,
On 8 June 2015 at 07:40, Krzysztof Kozlowski k.kozlow...@samsung.com wrote:
On 07.06.2015 22:20, Anand Moon wrote:
Facilitate getting required 3.3V and 1.0V VDD supply for
EHCI controller on Exynos.
With the
Hi Krzysztof ,
On 8 June 2015 at 07:40, Krzysztof Kozlowski k.kozlow...@samsung.com wrote:
On 07.06.2015 22:20, Anand Moon wrote:
Facilitate getting required 3.3V and 1.0V VDD supply for
EHCI controller on Exynos.
With the patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add
exynos_dsi_host_transfer() can be called through a panel driver while
DSI is turning down. It is possible because the function checks only
whether DSI is initialized or not, and there is a moment which DSI is
set by uninitialized, but DSI is still turning down. To prevent it,
DSI must be set by
The commit edd4ab055931 (power: max17042_battery: add HEALTH and TEMP_*
properties support) added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.
This caused reporting battery health always as over voltage or
over heated.
Add some safe values for over head and over voltage. The Trats2 uses 3.8
V battery and during testing it operated properly under 4.48 V.
Signed-off-by: Krzysztof Kozlowski k.kozlow...@samsung.com
---
arch/arm/boot/dts/exynos4412-trats2.dts | 3 +++
1 file changed, 3 insertions(+)
diff --git
On 06/05/2015 01:54 PM, MyungJoo Ham wrote:
IRQ signal before driver probe is needless because driver sends
current state after platform booting done.
So, this patch clears MUIC IRQ bits before request IRQ.
Signed-off-by: Jaewon Kim jaewon02@samsung.com
---
During probe the regulator (if present) was enabled but not disabled in
case of failure. So an unsuccessful probe lead to enabling the
regulator which was actually not needed because the device was not
enabled.
Additionally each deferred probe lead to increase of regulator enable
count so it
On 07.06.2015 22:20, Anand Moon wrote:
Facilitate getting required 3.3V and 1.0V VDD supply for
EHCI controller on Exynos.
With the patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
the
13 matches
Mail list logo
