sunxi clock drivers use dt node name as clock name, but clock
nodes should be named clk@X, so the names would be the same.
Let the drivers read clock names from dt clock-output-names
property.
Signed-off-by: Chen-Yu Tsai w...@csie.org
Acked-by: Maxime Ripard maxime.rip...@free-electrons.com
clock-output-names is now required for most of sunxi clock nodes, to
provide the name of the corresponding clock. Add the new requirements,
exceptions, as well as examples.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
Documentation/devicetree/bindings/clock/sunxi.txt | 32
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun5i-a10s.dtsi | 30 --
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun6i-a31.dtsi | 19 ++-
1 file
Hi,
This is the remaining part of v3 of the Allwinner A20 GMAC glue layer for
stmmac. The stmmac driver changes have been merged through net-next. The
remaining bits are clock and DT patches. The patches should be applied
over my clock renaming patches.
The Allwinner A20 SoC integrates an early
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun7i-a20.dtsi | 15 +++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index fc7f470..5fbac23 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun7i-a20.dtsi | 28
1 file changed, 28
U-Boot will insert MAC address into the device tree image.
It looks up ethernet[0-5] aliases to find the ethernet nodes.
Alias GMAC as ethernet0, as it is the only ethernet controller used.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun7i-a20.dtsi | 2 +-
1 file changed, 1
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun7i-a20-cubieboard2.dts | 27 ---
1 file changed, 12 insertions(+), 15 deletions(-)
diff
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai w...@csie.org
---
arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 27 +++--
1 file changed, 12 insertions(+), 15 deletions(-)
diff
Hi Patrick,
I dont have any ttyS0.conf file in my etc directory.
Can you tell, how to add this.
Regards
Punith
--
You received this message because you are subscribed to the Google Groups
linux-sunxi group.
To unsubscribe from this group and stop receiving emails from it, send an email
to
11 matches
Mail list logo