Enable the following board hardware features: - Gigabit Ethernet - SDIO Wi-Fi on mmc1 - SPI flash on spi0 - Status LED - Dual-role micro-USB connection
Also provide nodes for the UARTs exposed by the 40-pin GPIO header. A couple of fixes were made: - Updating a couple of regulators from the schematic - Marking the CPU's power supply as such Signed-off-by: Samuel Holland <sam...@sholland.org> --- .../boot/dts/allwinner/sun50i-a64-orangepi-win.dts | 141 ++++++++++++++++++++- 1 file changed, 134 insertions(+), 7 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts index bf42690a3361..fd0636381d7f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts @@ -1,5 +1,6 @@ /* * Copyright (C) 2017 Jagan Teki <jt...@openedev.com> + * Copyright (C) 2017-2018 Samuel Holland <sam...@sholland.org> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -51,23 +52,97 @@ compatible = "xunlong,orangepi-win", "allwinner,sun50i-a64"; aliases { + ethernet0 = &emac; serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; }; chosen { stdout-path = "serial0:115200n8"; }; + + leds { + compatible = "gpio-leds"; + + status { + label = "orangepi:green:status"; + gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + }; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 14 GPIO_ACTIVE_HIGH>; /* PD14 */ + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 7 GPIO_ACTIVE_HIGH>; /* PD7 */ + status = "okay"; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */ + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; }; &ehci1 { status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_gmac_3v3>; + status = "okay"; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo2>; + vqmmc-supply = <®_dldo4>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; status = "okay"; }; @@ -89,10 +164,9 @@ #include "axp803.dtsi" ®_aldo1 { - regulator-always-on; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-name = "afvcc-csi"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc-csi"; }; ®_aldo2 { @@ -166,7 +240,13 @@ ®_eldo1 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-name = "cpvdd"; + regulator-name = "vcc-pc"; +}; + +®_eldo3 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi"; }; ®_fldo1 { @@ -191,13 +271,60 @@ regulator-name = "vcc-rtc"; }; +&spi0 { + status = "okay"; + + spi-flash@0 { + compatible = "mxicy,mx25l1606e", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + m25p,fast-read; + status = "okay"; + }; +}; + +/* On debug connector */ &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; -&usbphy { +/* Wi-Fi/BT */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + status = "disabled"; +}; + +/* On Pi-2 connector, RTS/CTS optional */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; +}; + +/* On Pi-2 connector, RTS/CTS optional */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "disabled"; +}; + +/* On Pi-2 connector (labeled for SPI1), RTS/CTS optional */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "disabled"; +}; + +&usb_otg { + dr_mode = "otg"; status = "okay"; }; +&usbphy { + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; -- 2.16.1 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.