Dne 16.1.2017 v 20:14 Icenowy Zheng napsal(a):
> The PHY0 on H3 can be wired either to MUSB controller or OHCI/EHCI
> controller.
>
> The original driver wired it to OHCI/EHCI controller; however, as the
> code to use PHY0 as OHCI/EHCI is missing, it makes the PHY fully
> unusable.
>
> Rename the register (according to its function and the name in BSP
> driver), and remove the code which wires the PHY0 to OHCI/EHCI, as MUSB
> can support both peripheral and host mode (although the host mode of
> MUSB is buggy).
>
> The register that is renamed is now unused, as its initial value is just
> MUSB mode. However, when OHCI/EHCI mode support is added, the register
> can be used again.
>
> Signed-off-by: Icenowy Zheng <icen...@aosc.xyz>
> ---
> drivers/phy/phy-sun4i-usb.c | 25 +++++++++----------------
> 1 file changed, 9 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-usb.c
> index bf28a0fdd569..6b193a635c6b 100644
> --- a/drivers/phy/phy-sun4i-usb.c
> +++ b/drivers/phy/phy-sun4i-usb.c
> @@ -49,7 +49,7 @@
> #define REG_PHYBIST 0x08
> #define REG_PHYTUNE 0x0c
> #define REG_PHYCTL_A33 0x10
> -#define REG_PHY_UNK_H3 0x20
> +#define REG_PHY_OTGCTL 0x20
You have added REG_PHY_OTGCTL, but it is not used below.
regards,
o.
> #define REG_PMU_UNK1 0x10
>
> @@ -269,23 +269,16 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> writel(val & ~2, phy->pmu + REG_PMU_UNK1);
> }
>
> - if (data->cfg->type == sun8i_h3_phy) {
> - if (phy->index == 0) {
> - val = readl(data->base + REG_PHY_UNK_H3);
> - writel(val & ~1, data->base + REG_PHY_UNK_H3);
> - }
> - } else {
> - /* Enable USB 45 Ohm resistor calibration */
> - if (phy->index == 0)
> - sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
> + /* Enable USB 45 Ohm resistor calibration */
> + if (phy->index == 0)
> + sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
>
> - /* Adjust PHY's magnitude and rate */
> - sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
> + /* Adjust PHY's magnitude and rate */
> + sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
>
> - /* Disconnect threshold adjustment */
> - sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
> - data->cfg->disc_thresh, 2);
> - }
> + /* Disconnect threshold adjustment */
> + sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
> + data->cfg->disc_thresh, 2);
>
> sun4i_usb_phy_passby(phy, 1);
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
