Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2018-02-06 Thread 'schoone...@btinternet.com' via Machinekit 

Read the gist that Michael did for the DE0

There is a link to it in the blogs.

You have to set the NIC MAC address etc and then restart


On 06/02/2018 23:54, mugginsac wrote:

I finally got the USB console working under stretch.
I didn't have the dtb file that it was looking 
(socfpga_cyclone5_de10_nano.dtb) for in the 
boot/dtbs/4.9.68-socfpga-r3/ directory.
After I fixed that it is either loading the kernel or trying to load 
the kernel. It is getting a crc error and then starting over to try 
and load the kernel.


Any help interpreting what it is telling me would be greatly 
appreciated. The log is below:


=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.06 15:47:15 
=~=~=~=~=~=~=~=~=~=~=~=


U-Boot SPL 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1


U-Boot 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14 -0800)

CPU:   Altera SoCFPGA Platform
FPGA:  Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT:  SD/MMC Internal Transceiver (3.0V)
   Watchdog enabled
I2C:   ready
DRAM:  1 GiB
MMC:   dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Terasic DE10-Nano
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot:  2 1 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:2...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
179 bytes read in 21 ms (7.8 KiB/s)
1:    Linux 4.9.68-socfpga-r3
Retrieving file: /boot/vmlinuz-4.9.68-socfpga-r3
5455176 bytes read in 380 ms (13.7 MiB/s)
append: root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait quiet
Retrieving file: 
/boot/dtbs/4.9.68-socfpga-r3/socfpga_cyclone5_de10_nano.dtb

14997 bytes read in 45 ms (325.2 KiB/s)
## Flattened Device Tree blob at 0200
   Booting using the fdt blob at 0x200
   reserving fdt memory region: addr=0 size=1000
   Loading Device Tree to 03ff9000, end 03fffa94 ... OK

Starting kernel ...


U-Boot SPL 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1


U-Boot 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14 -0800)

CPU:   Altera SoCFPGA Platform
FPGA:  Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT:  SD/MMC Internal Transceiver (3.0V)
   Watchdog enabled
I2C:   ready
DRAM:  1 GiB
MMC:   dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Terasic DE10-Nano
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot:  2 0

--
website: http://www.machinekit.io blog: http://blog.machinekit.io 
github: https://github.com/machinekit

---
You received this message because you are subscribed to the Google 
Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send 
an email to machinekit+unsubscr...@googlegroups.com 
.

Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.


--
website: http://www.machinekit.io blog: http://blog.machinekit.io github: 
https://github.com/machinekit
--- 
You received this message because you are subscribed to the Google Groups "Machinekit" group.

To unsubscribe from this group and stop receiving emails from it, send an email 
to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.

Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2018-02-06 Thread mugginsac 
I finally got the USB console working under stretch. 
I didn't have the dtb file that it was looking 
(socfpga_cyclone5_de10_nano.dtb) for in the boot/dtbs/4.9.68-socfpga-r3/ 
directory.
After I fixed that it is either loading the kernel or trying to load the 
kernel. It is getting a crc error and then starting over to try and load 
the kernel.

Any help interpreting what it is telling me would be greatly appreciated. 
The log is below:

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.06 15:47:15 
=~=~=~=~=~=~=~=~=~=~=~=

U-Boot SPL 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1


U-Boot 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14 -0800)

CPU:   Altera SoCFPGA Platform
FPGA:  Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT:  SD/MMC Internal Transceiver (3.0V)
   Watchdog enabled
I2C:   ready
DRAM:  1 GiB
MMC:   dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment

In:serial
Out:   serial
Err:   serial
Model: Terasic DE10-Nano
Net:   
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot:  2 1 0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:2...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
179 bytes read in 21 ms (7.8 KiB/s)
1:Linux 4.9.68-socfpga-r3
Retrieving file: /boot/vmlinuz-4.9.68-socfpga-r3
5455176 bytes read in 380 ms (13.7 MiB/s)
append: root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait quiet
Retrieving file: /boot/dtbs/4.9.68-socfpga-r3/socfpga_cyclone5_de10_nano.dtb
14997 bytes read in 45 ms (325.2 KiB/s)
## Flattened Device Tree blob at 0200
   Booting using the fdt blob at 0x200
   reserving fdt memory region: addr=0 size=1000
   Loading Device Tree to 03ff9000, end 03fffa94 ... OK

Starting kernel ...


U-Boot SPL 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1


U-Boot 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14 -0800)

CPU:   Altera SoCFPGA Platform
FPGA:  Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT:  SD/MMC Internal Transceiver (3.0V)
   Watchdog enabled
I2C:   ready
DRAM:  1 GiB
MMC:   dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment

In:serial
Out:   serial
Err:   serial
Model: Terasic DE10-Nano
Net:   
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot:  2 0 

-- 
website: http://www.machinekit.io blog: http://blog.machinekit.io github: 
https://github.com/machinekit
--- 
You received this message because you are subscribed to the Google Groups 
"Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.

[Machinekit] Re: machinekit stretch error help

2018-02-06 Thread gary 
Installed xauth, had to install some lib's first but did get it installed..
But have a new problem

I get the first screen to load the machinekit configuration selector 
but the screen is blank. has the ok cancel buttons but not usable 
and shows none of the different config files like ARM exc exc just a blank 
choose config screen that i cant exit out of. and don't know how to find 
the error
i am not getting any error messages just sits at blank screen forever 
I control c twice in putty terminal and it will exit back to the putty term 
prompt
but get no error there also..
Tried on windows and Linux with putty same problem

Thanks gary  



On Monday, February 5, 2018 at 4:23:59 PM UTC-5, gary wrote:

> I installed the machinekit BBB image with stetch and as soon as i try to
> run machinekit i am getting this error
>
> and not being a programmer i do not know how to correct it, if possible 
>
> application-specific initialization failed: no display name and no 
> $DISPLAY environment variable
> Error in startup script: invalid command name "image"
> while executing
> "image create photo -file $f/$i.gif"
> invoked from within
> "if [file exists $f/$i.gif] {
> return [image create photo -file $f/$i.gif]
> }"
> (procedure "linuxcnc::image_search" line 7)
> invoked from within
> "linuxcnc::image_search machinekit-wizard"
> invoked from within
> "set logo [linuxcnc::image_search machinekit-wizard]"
> (file "/usr/lib/tcltk/linuxcnc/bin/pickconfig.tcl" line 31)
>
> Thanks gary
>

-- 
website: http://www.machinekit.io blog: http://blog.machinekit.io github: 
https://github.com/machinekit
--- 
You received this message because you are subscribed to the Google Groups 
"Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.

[Machinekit] Re: machinekit stretch error help

2018-02-06 Thread Karl Jacobs 
Had the same issue on stretch. 
sudo apt-get install xauth
touch ~/.Xauthority
solved the problem
Karl


Am Montag, 5. Februar 2018 22:23:59 UTC+1 schrieb gary:
>
> I installed the machinekit BBB image with stetch and as soon as i try to
> run machinekit i am getting this error
>
> and not being a programmer i do not know how to correct it, if possible 
>
> application-specific initialization failed: no display name and no 
> $DISPLAY environment variable
> Error in startup script: invalid command name "image"
> while executing
> "image create photo -file $f/$i.gif"
> invoked from within
> "if [file exists $f/$i.gif] {
> return [image create photo -file $f/$i.gif]
> }"
> (procedure "linuxcnc::image_search" line 7)
> invoked from within
> "linuxcnc::image_search machinekit-wizard"
> invoked from within
> "set logo [linuxcnc::image_search machinekit-wizard]"
> (file "/usr/lib/tcltk/linuxcnc/bin/pickconfig.tcl" line 31)
>
> Thanks gary
>

-- 
website: http://www.machinekit.io blog: http://blog.machinekit.io github: 
https://github.com/machinekit
--- 
You received this message because you are subscribed to the Google Groups 
"Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.