Re: [MBZ] Lary T. Mini split
Now that you say that, yeah, that’s right. I’s cornfused Sent from my iPad > On Feb 20, 2022, at 9:31 AM, Jim Cathey via Mercedes > wrote: > > >> >> I don’t know specifically where it might be on your car but on 210s and 163s >> the TCM is under the steering wheel above the under dash panel. > > On my W210's the TCM is under the little hatch in the engine compartment > near the firewall on the passenger side. > > -- Jim > > > ___ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Lary T. Mini split
> I don’t know specifically where it might be on your car but on 210s and 163s > the TCM is under the steering wheel above the under dash panel. On my W210's the TCM is under the little hatch in the engine compartment near the firewall on the passenger side. -- Jim ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Lary T. Mini split
I don’t know specifically where it might be on your car but on 210s and 163s the TCM is under the steering wheel above the under dash panel. You might ask in Benzworld or do a net search. --FT Sent from iFōn > On Feb 20, 2022, at 12:25 AM, Larry Turner via Mercedes > wrote: > > Hey ya'll, > I was reviewing my emails nd found I had been negligent in thanking all who > replied to my questions about MInisplits! The knowledge of this list knows > no bounds! > > Next, I see questions abut the 722.6 tranny like the one in my 06 E350AWD - I > worked through all the suggested fixed for mine being stuck in limp mode - > R'd the Conductor plate and ATF, replaced the electr plug and it's o-rings > and got to the TCR (Trans Control Module). I checked everywhere I could > think of and came up with a location of the passenger foot well. I removed > the panel over the passenger's feet and all I found was a courtesy light. I > check with Sun Valley and was told the same location so it still sits in the > driveway as a paper weight - which it's very good at! ;-) > > I know there are some E350's with the 722.6 on this list -- if anyone finds > their TCM, please let me know. I asked the local dealer how they T'Shoot the > Tran's on mid 2000 MB's, and he said we don't;. If they have a problem, they > replace the Tranny at around $8K. I don't see that as an economically > practical solution!// > > Anyway, have been unable to find a decent replacement for our 91 300D 2.5T > that fits our budget and other needs. Plus, while doing the Trans work I > tore my rotator cuff making me even less able to do any sweat equity work. > But I am still hoping to find a decent W124 Diesel someday > > I hope everyone had a great Christmas and New Years? I am sure ya'll are as > happy as I am with Pres Bidens stellar performance?? Have a great Spring and > enjoy the coming Summer! > > Take care - > Larry > >> On 7/22/2021 7:10 PM, Ronald Courcy via Mercedes wrote: >> Is your shop a free standing metal building with two inches of insulation? >> Where are you located? 12 to 14k of cooling sounds inadequate and the >> heating needs may not be met as well. >> Most min split systems come with adequate refrigerant in the outside unit >> for a 25 foot run of tubing. There are high efficiency units available that >> can provide heat when outside temperature is five to ten degrees below zero. >> Installation is pretty simple. Run 220v power to outside unit. Low voltage >> wiring between inside and outside units. install llneset tubing in-between >> the inner band other units. Outside unit needs to sit on a slab on the >> ground or on brackets attached to the building. You will need to rent or >> borrow a vacume pump. After connecting the tubbing between the inner and >> outer unit you will need to "pull a vacume" on the tubing inorder to create >> a negative pressure and to verify that there is no leaks in the connections. >> Than you would open the valves on the outside unit to allow the refrigerant >> to flow through the system. Of course if you install yourself you will void >> the warranty. There are some systems that are made to use precharged >> linesets so you do not have to use a vacume pump. I HAVE WHOLESALE ACCESS TO >> SEVERAL DIFFERENT MANUFACTURES MINI SPLIT SYSTEMS (FUJITSU, Mitsubishi,LG >> etc) AND WOULD BE WILLING TO HELP YOU WITH YOUR selection/PURCHASE AND >> INSTALL. Ron Courcy >> >> >> From: Mercedes on behalf >> ofmercedes-requ...@okiebenz.com >> Sent: Thursday, July 22, 2021 3:48 PM >> To:mercedes@okiebenz.com >> Subject: Mercedes Digest, Vol 188, Issue 91 >> >> Send Mercedes mailing list submissions to >> mercedes@okiebenz.com >> >> To subscribe or unsubscribe via the World Wide Web, visit >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> or, via email, send a message with subject or body 'help' to >> mercedes-requ...@okiebenz.com >> >> You can reach the person managing the list at >> mercedes-ow...@okiebenz.com >> >> When replying, please edit your Subject line so it is more specific >> than "Re: Contents of Mercedes digest..." >> >> >> Today's Topics: >> >>1. 2012 S600 V12 needs head gasket - $13,000 (Allan Streib) >>2. 1991 ? $1,000 (Allan Streib) >>3. Re: Red death (Allan Streib) >>4. Re: Red death (Curt Raymond) >>5. Re: Red death (Allan Streib) >>6. Re: Mini splits (Larry Turner) >>7. Re: Mini splits (Kevin Kraly) >> >> >> -- >> >> Message: 1 >> Date: Thu, 22 Jul 2021 14:52:53 -0400 >> From: "Allan Streib" >> To: "Mercedes Discussion List" >> Subject: [MBZ] 2012 S600 V12 needs head gasket - $13,000 >> Message-ID:<084711ca-8b4d-4c62-bd9f-18a94d432...@www.fastmail.com> >> Content-Type: text/plain >> >> >>
Re: [MBZ] Lary T. Mini split
Hey ya'll, I was reviewing my emails nd found I had been negligent in thanking all who replied to my questions about MInisplits! The knowledge of this list knows no bounds! Next, I see questions abut the 722.6 tranny like the one in my 06 E350AWD - I worked through all the suggested fixed for mine being stuck in limp mode - R'd the Conductor plate and ATF, replaced the electr plug and it's o-rings and got to the TCR (Trans Control Module). I checked everywhere I could think of and came up with a location of the passenger foot well. I removed the panel over the passenger's feet and all I found was a courtesy light. I check with Sun Valley and was told the same location so it still sits in the driveway as a paper weight - which it's very good at! ;-) I know there are some E350's with the 722.6 on this list -- if anyone finds their TCM, please let me know. I asked the local dealer how they T'Shoot the Tran's on mid 2000 MB's, and he said we don't;. If they have a problem, they replace the Tranny at around $8K. I don't see that as an economically practical solution!// Anyway, have been unable to find a decent replacement for our 91 300D 2.5T that fits our budget and other needs. Plus, while doing the Trans work I tore my rotator cuff making me even less able to do any sweat equity work. But I am still hoping to find a decent W124 Diesel someday I hope everyone had a great Christmas and New Years? I am sure ya'll are as happy as I am with Pres Bidens stellar performance?? Have a great Spring and enjoy the coming Summer! Take care - Larry On 7/22/2021 7:10 PM, Ronald Courcy via Mercedes wrote: Is your shop a free standing metal building with two inches of insulation? Where are you located? 12 to 14k of cooling sounds inadequate and the heating needs may not be met as well. Most min split systems come with adequate refrigerant in the outside unit for a 25 foot run of tubing. There are high efficiency units available that can provide heat when outside temperature is five to ten degrees below zero. Installation is pretty simple. Run 220v power to outside unit. Low voltage wiring between inside and outside units. install llneset tubing in-between the inner band other units. Outside unit needs to sit on a slab on the ground or on brackets attached to the building. You will need to rent or borrow a vacume pump. After connecting the tubbing between the inner and outer unit you will need to "pull a vacume" on the tubing inorder to create a negative pressure and to verify that there is no leaks in the connections. Than you would open the valves on the outside unit to allow the refrigerant to flow through the system. Of course if you install yourself you will void the warranty. There are some systems that are made to use precharged linesets so you do not have to use a vacume pump. I HAVE WHOLESALE ACCESS TO SEVERAL DIFFERENT MANUFACTURES MINI SPLIT SYSTEMS (FUJITSU, Mitsubishi,LG etc) AND WOULD BE WILLING TO HELP YOU WITH YOUR selection/PURCHASE AND INSTALL. Ron Courcy From: Mercedes on behalf ofmercedes-requ...@okiebenz.com Sent: Thursday, July 22, 2021 3:48 PM To:mercedes@okiebenz.com Subject: Mercedes Digest, Vol 188, Issue 91 Send Mercedes mailing list submissions to mercedes@okiebenz.com To subscribe or unsubscribe via the World Wide Web, visit http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com or, via email, send a message with subject or body 'help' to mercedes-requ...@okiebenz.com You can reach the person managing the list at mercedes-ow...@okiebenz.com When replying, please edit your Subject line so it is more specific than "Re: Contents of Mercedes digest..." Today's Topics: 1. 2012 S600 V12 needs head gasket - $13,000 (Allan Streib) 2. 1991 ? $1,000 (Allan Streib) 3. Re: Red death (Allan Streib) 4. Re: Red death (Curt Raymond) 5. Re: Red death (Allan Streib) 6. Re: Mini splits (Larry Turner) 7. Re: Mini splits (Kevin Kraly) -- Message: 1 Date: Thu, 22 Jul 2021 14:52:53 -0400 From: "Allan Streib" To: "Mercedes Discussion List" Subject: [MBZ] 2012 S600 V12 needs head gasket - $13,000 Message-ID:<084711ca-8b4d-4c62-bd9f-18a94d432...@www.fastmail.com> Content-Type: text/plain https://louisville.craigslist.org/cto/d/taylorsville-2012-mercedes-s600-v12/7354620819.html Allan -- Message: 2 Date: Thu, 22 Jul 2021 14:55:22 -0400 From: "Allan Streib" To: "Mercedes Discussion List" Subject: [MBZ] 1991 ? $1,000 Message-ID: Content-Type: text/plain Any questions? https://chicago.craigslist.org/nwi/cto/d/wheatfield-1991-mercedes-benz/7354590859.html Allan -- Message: 3 Date: Thu, 22 Jul 2021 15:00:35 -0400 From: "Allan Streib" To: "Mercedes Discussion List" Subject: Re: [MBZ] Red death
Re: [MBZ] Lary T. Mini split
I surprised myself assuming the indoor units on my LGs were low voltage…. Uh, nope… -FT Sent from my iPad > On Jul 22, 2021, at 4:11 PM, Ronald Courcy via Mercedes > wrote: > > Low voltage wiring between inside and outside units. install llneset tubing > in-between the inner band other units. ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Lary T. Mini split
Is your shop a free standing metal building with two inches of insulation? Where are you located? 12 to 14k of cooling sounds inadequate and the heating needs may not be met as well. Most min split systems come with adequate refrigerant in the outside unit for a 25 foot run of tubing. There are high efficiency units available that can provide heat when outside temperature is five to ten degrees below zero. Installation is pretty simple. Run 220v power to outside unit. Low voltage wiring between inside and outside units. install llneset tubing in-between the inner band other units. Outside unit needs to sit on a slab on the ground or on brackets attached to the building. You will need to rent or borrow a vacume pump. After connecting the tubbing between the inner and outer unit you will need to "pull a vacume" on the tubing inorder to create a negative pressure and to verify that there is no leaks in the connections. Than you would open the valves on the outside unit to allow the refrigerant to flow through the system. Of course if you install yourself you will void the warranty. There are some systems that are made to use precharged linesets so you do not have to use a vacume pump. I HAVE WHOLESALE ACCESS TO SEVERAL DIFFERENT MANUFACTURES MINI SPLIT SYSTEMS (FUJITSU, Mitsubishi,LG etc) AND WOULD BE WILLING TO HELP YOU WITH YOUR selection/PURCHASE AND INSTALL. Ron Courcy From: Mercedes on behalf of mercedes-requ...@okiebenz.com Sent: Thursday, July 22, 2021 3:48 PM To: mercedes@okiebenz.com Subject: Mercedes Digest, Vol 188, Issue 91 Send Mercedes mailing list submissions to mercedes@okiebenz.com To subscribe or unsubscribe via the World Wide Web, visit http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com or, via email, send a message with subject or body 'help' to mercedes-requ...@okiebenz.com You can reach the person managing the list at mercedes-ow...@okiebenz.com When replying, please edit your Subject line so it is more specific than "Re: Contents of Mercedes digest..." Today's Topics: 1. 2012 S600 V12 needs head gasket - $13,000 (Allan Streib) 2. 1991 ? $1,000 (Allan Streib) 3. Re: Red death (Allan Streib) 4. Re: Red death (Curt Raymond) 5. Re: Red death (Allan Streib) 6. Re: Mini splits (Larry Turner) 7. Re: Mini splits (Kevin Kraly) -- Message: 1 Date: Thu, 22 Jul 2021 14:52:53 -0400 From: "Allan Streib" To: "Mercedes Discussion List" Subject: [MBZ] 2012 S600 V12 needs head gasket - $13,000 Message-ID: <084711ca-8b4d-4c62-bd9f-18a94d432...@www.fastmail.com> Content-Type: text/plain https://louisville.craigslist.org/cto/d/taylorsville-2012-mercedes-s600-v12/7354620819.html Allan -- Message: 2 Date: Thu, 22 Jul 2021 14:55:22 -0400 From: "Allan Streib" To: "Mercedes Discussion List" Subject: [MBZ] 1991 ? $1,000 Message-ID: Content-Type: text/plain Any questions? https://chicago.craigslist.org/nwi/cto/d/wheatfield-1991-mercedes-benz/7354590859.html Allan -- Message: 3 Date: Thu, 22 Jul 2021 15:00:35 -0400 From: "Allan Streib" To: "Mercedes Discussion List" Subject: Re: [MBZ] Red death Message-ID: <080c0282-385a-4c14-ba33-18036aace...@www.fastmail.com> Content-Type: text/plain I was curious about it, since two people in my immediate household contracted COVID in November. I never had any symptoms. Also been going to the gym 4x week throughout the pandemic, very little mask-wearing there, never had any symptoms. A few weeks ago I got an antibody test, which was negative. Allan On Thu, Jul 22, 2021, at 1:12 PM, Curt Raymond via Mercedes wrote: > Is it that it mutates into something less deadly or that human's develop > antibodies (kind of a mutation in its own right) that better fight the virus? > -Curt > > On Thursday, July 22, 2021, 1:07:40 PM EDT, Randy Bennell via Mercedes > wrote: > > I do hope that you are correct. However, I would prefer not to be one of > those who dies before it mutates into something less likely to kill me. > > > > On 22/07/2021 11:26 AM, Rick Knoble via Mercedes wrote: > > It is impossible to contain a virus that has become endemic. The OC43 > > coronavirus likely caused an epidemic in the mid 1800's. It is now a common > > cold. That's how coronavirus' work. If they killed their hosts, the virus > > would burn itself out (see "ebola"). They become easier to spread, but less > > lethal. This particular virus will mutate to become another cold virus. > > Whether or not the media and the politicians will admit that is another > > story. > > > > Secondary assignment. Look up ADE, and for bonus credit look up Original > > Antigenic Sin. > > > > > > Rick > > > > From: mercedes@okiebenz.com > > Sent: July 22, 2021 11:07 AM > > To: mercedes@okiebenz.com > > Reply-to: mercedes@okiebenz.com
