----- Forwarded by Tru H Le/GD_AAAV/GDAS on 10/11/2005 16:39 ----- [EMAIL PROTECTED] 10/11/2005 16:34
To [EMAIL PROTECTED] cc Subject Message rejected Your message to misc@openbsd.org was rejected because it was not explicitly addressed to the misc mailing list. If you intended to send a blind carbon copy, you must include a valid Bcc: header. ----- Message from [EMAIL PROTECTED] on Tue, 11 Oct 2005 15:37:08 -0400 ----- To: [EMAIL PROTECTED] cc: [EMAIL PROTECTED], [EMAIL PROTECTED] Subject: FDDI->Ethernet mirror/bridge? I have the same questions too: Any idea, how I can convert the FDDI to Ethernet and via versa. "I want to take all traffic on the FDDI ring and dump it over to the FastEthernet network." Thanks, Tru Le ([EMAIL PROTECTED]) General Dynamics (W) 703 490 7548 On Thu, 27 Apr 2000, Tyler Allison wrote: > Anybody have experience with using an OBSD boxes to create a low cost FDDI > to FastEthernet converter? I want to take all traffic on the FDDI ring and > dump it over to the FastEthernet network. > > I'm having the darndest time even finding a hardware solution for this from > any Vendor. Any ideas would be appreciated. Technically, because FDDI can have enormous frame sizes, you can't simply produce a "converted" - there's no way to do that at the DLC layer. IP, on the other hand, has a really neat feature called packet fragmentation :-). But then, the device you're looking for is called a "router" - and lots of people make those. *IF* you can configure every single host on the FDDI ring to use a framesize of no more than 1545 (?) bytes, then you can use a simple bridge or media converter. A media converter is not, strictly speaking, even theoretically possible. A media converter simply translates the electrical characteristics of a signal into some other form. For example, 10b2 (coax) ethernet to 10bT (twisted pair) ethernet conversion would use a "media converter" - also commonly known as a "transceiver". You're asking for the same type of device as an Ethernet-to-Token-Ring converter. They only work under very strict conditions, and they wind up operating (at least) like a bridge, at layer 2. Take an OpenBSD box. Add one ethernet card. Add one FDDI card. Configure the br0 device - there's been LOTS of discussion recently on these lists about setting up bridge groups under OpenBSD. If you want a standalone solution that you don't have to put together, go to www.blackbox.com, and search (one at a time...) for these product numbers, and you'll find a number of devices that may suit your needs: LT0003A-4DMI, 38460, LT0002A, WS-C1924F-A, NP-1F-D-MM= (note - those last two #s are actually Cisco product, which can probably be found cheaper elsewhere) Sorry, but ethernet and FDDI just aren't directly compatible. It's definitely do-able (I've seen it done with FreeBSD, anyway) but there are other solutions out there, too. -Adam -- Adam Thompson, MCNE, MCSE, CWT, A+ Vice-President / Chief Technology Officer, Commerce Design Inc. <[EMAIL PROTECTED]> tel: (204) 942-1648, fax: (204) 989-8080, cell: (204) 782-6198 This is an e-mail from General Dynamics Land Systems. It is for the intended recipient only and may contain confidential and privileged information. No one else may read, print, store, copy, forward or act in reliance on it or its attachments. If you are not the intended recipient, please return this message to the sender and delete the message and any attachments from your computer. Your cooperation is appreciated. This is an e-mail from General Dynamics Land Systems. It is for the intended recipient only and may contain confidential and privileged information. No one else may read, print, store, copy, forward or act in reliance on it or its attachments. If you are not the intended recipient, please return this message to the sender and delete the message and any attachments from your computer. Your cooperation is appreciated.