In this case I would copy the ppd file into ~/Downloads,
which is permitted by unveil by default inside /etc/firefox/unveil.main:
~/Downloads rwc
In th file selection dialog box it can be difficult to select a directory.
If you are having trouble doing so type '/' and then you can
enter the
Hello,
I recently managed to find an ISP that could provide IPv6 for my company,
unfortunately this was a custom config = expensive and they have no
implementation expernence = bad idea.
Long story short they delivered a /56 on their router port (local ethernet
segment), no way to
Hi,
I have a Supermicro A1SRM-LN7F/LN5F, which has a lot of the same hardware as
the board you are interested in.
For IPMI I did a:
config -e -o bsd.new /bsd
enable ipmi
I run vmd (virtual machines) without problems.
Doing 6 port (+1 port for admin) routing+pf+nat, mail server, sip server,
Hello,
As I am tidying up my network by segregating it into secure, general inet
access and guest networks.
I would like to keep tabs on the MAC/IP addresses in my secure net.
I do know how to do this, but keeping track of ethernet MAC addresses seems
quite cumbersome in OpenBSD, not that it
Hello,
I have been using OpenUPS for my rack for at least 3 years without a single
problem powering server + switch + media converter with 12VDC.
This is a DC-DC UPS meaning that it does not replicate a UPS that you simply
plug in and it works.
The reasons for me using OpenUPS are:
-An open
Hi List,
I have an issue with DisplayLink CONV-USB2DVI and OpenBSD 5.1/amd64 (and
snapshot/amd64). X cannot be launched, I have got the following error :
wsudl(0): We are not attached to the udl driver
The device is detected, dmesg :
-
udl0 at uhub6 port 2 DisplayLink CONV-USB2DVI rev
Could this be related to the space preceding in the device declaration?
Option device / dev/wsdisplay1 -- Option device /dev/wsdisplay1
Thanks for your reply, Вовочка, but this is a typo mistake I have made
while I write my mail.
--
Alexis de BRUYN
On 02.08.2012 21:48, Matthieu Herrb wrote:
This is the xorg.conf I use to test wsudl:
Section Devicë
Identifier Card0
Driver wsudl
Option Devicë /dev/ttyD0
EndSection
(Yes that's it. Modern X can figure out everything else).
Thanks for your help Matthieu,
hey Kevin,
On Fri, Jun 06, 2008 at 10:29:27PM -0500, K K wrote:
Is anybody else seeing cold boot failures on Soekris Net5501-70
with comBIOS v1.33b and OpenBSD 4.3? I asked earlier on the
soekris-tech list, received no replies.
I've seen it but had no screen capture so far
The console
Hi,
I am using ipsecctl and /etc/ipsec.conf to create an IPSec tunnel to a
WatchGuard Firebox X700 in my company. It works fine, but the
re-keying always makes some trouble, it does not always work. My
question now is, how can I set the keylifetimes for phase 1 and 2 in
/etc/ipsec.conf?
Hello,
I just want to inform you that the problems are resolved with the current
OpenBSD 3.9 bootfloppy
(ftp://ftp.openbsd.org/pub/OpenBSD/snapshots/i386/floppy39.fs). I just
added to the bootfloppy /etc/boot.conf (for console output via serial
port) and the network works without any problems ;)
Hi Alex,
I've written the floppy38.fs to my server via:
wget -O- wget ftp://ftp.de.openbsd.org/pub/snapshots/i386/floppy38.fs
/dev/hda (within the rescue system). I also tried some customized
floppy-images (with custom kernel options)
and it boots fine ;) But my problem is, that the fxp
Hi Alex again,
in my opinion it's a nic problem and not a network settings problem,
because i also have tried to obtain the network configuration via dhcp
(like in the rescue system) with the same result - fxp0: device timeout
Best regards,
Sven
Hi,
for comparison I have a similar PC at the
13 matches
Mail list logo
