Hello,
I went from a 4.7 snapshot to 4.8-current today.
I upgraded via untaring + following the upgrade guide for the WIP release
version (not pretty, but worked until today).
Upgrading worked fine, including the /sbin/oreboot.
Sysmerge.
Package upgrading worked, too.
I then restarted again, but the machine didn't come up.
Switch to console showed, that it hang at "starting networking".
This happened until I moved hostname.ath0 out of the way.
A /etc/netstart ath0 crashes the system.
A normal ifconfig ath0 up doesn't.
hostname.ath0:
up mediaopt hostap mode 11b chan 3 nwid SCHNEIER wpa wpapsk
0xadsfasdfasdfasdfasdf wpaakms psk
inet 172.16.1.1
OpenBSD 4.8-current (GENERIC) #357: Thu Sep 16 09:25:04 MDT 2010
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
499 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 268009472 (255MB)
avail mem = 253652992 (241MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/27/08, BIOS32 rev. 0 @ 0xfceb2
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10,
address 00:0d:b9:12:6b:04
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 00:0d:b9:12:6b:05
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr2 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12,
address 00:0d:b9:12:6b:06
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
ath0 at pci0 dev 12 function 0 "Atheros AR2413" rev 0x01: irq 9
ath0: AR2413 7.8 phy 4.5 rf 5.6, FCC2A*, address 00:1d:0f:af:98:88
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX3-2048>
wd0: 4-sector PIO, LBA, 1953MB, 4001760 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 15, version
1.0, legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask e1ef netmask ffef ttymask ffff
mtrr: K6-family MTRR support (2 registers)
nvram: invalid checksum
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
clock: unknown CMOS layout
umass0 at uhub0 port 1 configuration 1 interface 0 "Genesys Logic USB
Storage" rev 2.00/0.41 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Hitachi, HTS541680J9SA00, 0041> SCSI0
0/direct fixed
sd0: 76319MB, 512 bytes/sec, 156301488 sec total
