Combining boot floppies

2006-06-08 Thread Michael White
Hi all,

I'm attempting my first install of OpenBSD (version 3.9) on an HP Omnibook 
800CT (Pentium 166, 80 MB RAM, 4.3 GB HD, 3COM 3CXEM556 Carbus Ethernet 
card), coming over from RH9.0.  One peculiarity of the 800CTs is that the 
SCSI CDROM is not bootable, so I'm down to booting with floppies.

I first attempted to boot from floppyC39.fs, since that's supposed to be the 
image for laptops.  Well, it does recognize my Ethernet card, but seems to 
choke on the hard drive.  After recognizing the Ethernet card, I see the 
following:

--
wd0(wdc0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
wd0(wdc0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
WARNING: preposterous time in file system
WARNING: file system time much less than clock time
--

After that, the machine is locked up.  So I boot from floppy39.fs instead.  
That had no problem with the hard drive.  I was able to successfully 
partition the drive.  But that image does not recognize my Ethernet card, so 
I'm unable to retrieve any images (didn't see an option for PPP).

Even after formatting the hard drive under the floppy39.s floppy, the 
floppyC39.fs floppy chokes on the hard drive.

Is there any way to combine the two capabilities?  I.e. dropping to the shell, 
loading some driver or other, forcing the recognition, and re-starting where 
I left off?  The only reason I'm asking is because of a comment in the FAQ 
(section 4.3):

Yes, there may be situations where one install disk is required to support 
your SCSI adapter and another disk is required to support your network 
adapter. Fortunately, this is a rare event, and can usually be worked 
around.

I may have access to a Xircom network card - is that supported by the 
floppy39.s floppy?

Thanks in advance.
-- 
Michael White To protect people from the effects of folly is to
   fill the world with fools. -Herbert Spencer



state table, loopback and redirection

2006-06-08 Thread uc\.sheda
Hi,

I'm trying to set up ftp-proxy on my OpenBSD 3.9 box. I'm using the following 
configuration:

pf.conf:
  rdr pass proto tcp from any to any port 21 - 127.0.0.1 port 8021
  block log (all) all
  pass proto tcp from any to 127.16.218.129 to 127.0.0.1 port 8021 flags S/SA 
   keep state
network: 
* A bridge (bridge0) of 3 interfaces.
* Only one network (172.16/12) set on the first interface of the bridge (first 
brconfig add).
* Every interfaces are LEARNING and DISCOVER (as well as UP and RUNNING :).
* Loopback lo0 inteface is left to its default: 127.0.0.1/8, UP, LOOPBACK and 
RUNNING.

When 172.16.218.129 is trying to reach the port 21/tcp of 129.128.5.191, 
here is what happen:

* tcpdump -tei pflog0 port 21 or 8021: don't show anything
* tcpdump -tni bridge0 port 21 or 8021: just show the SYN coming from 
172.16.218.129, 
nothing else.
* pfctl -ss show 2 states:
   all tcp 127.0.0.1:8021 - 129.128.5.191:21 - 172.16.218.129:22585 
   CLOSED:SYN_SENT
   all tcp 172.16.218.129:22585 - 127.0.0.1:8021 SYN_SENT:CLOSED
* netstat -anp tcp show that ftp-proxy is listening on 127.0.0.1:8021 but don't 
receive anything (no socket in a state !=LISTEN with port 8021).

Is there something I'm missing? What is the exact meaning of the arrows seen in 
the 
pfctl -ss output?

thx,

sheda

Accidez au courrier ilectronique de La Poste : www.laposte.net ; 
3615 LAPOSTENET (0,34 /mn) ; til : 08 92 68 13 50 (0,34/mn)



Re: Combining boot floppies

2006-06-08 Thread Darrin Chandler
On Thu, Jun 08, 2006 at 01:08:04AM -0500, Michael White wrote:
 Hi all,
 
 I'm attempting my first install of OpenBSD (version 3.9) on an HP Omnibook 
 800CT (Pentium 166, 80 MB RAM, 4.3 GB HD, 3COM 3CXEM556 Carbus Ethernet 
 card), coming over from RH9.0.  One peculiarity of the 800CTs is that the 
 SCSI CDROM is not bootable, so I'm down to booting with floppies.
 
 I first attempted to boot from floppyC39.fs, since that's supposed to be 
 the 
 image for laptops.  Well, it does recognize my Ethernet card, but seems to 
 choke on the hard drive.  After recognizing the Ethernet card, I see the 
 following:
 
 --
 wd0(wdc0:0:0): timeout
   type: ata
   c_bcount: 512
   c_skip: 0
 wd0(wdc0:0:0): timeout
   type: ata
   c_bcount: 512
   c_skip: 0
 WARNING: preposterous time in file system
 WARNING: file system time much less than clock time
 --
 
 After that, the machine is locked up.  So I boot from floppy39.fs instead.  
 That had no problem with the hard drive.  I was able to successfully 
 partition the drive.  But that image does not recognize my Ethernet card, so 
 I'm unable to retrieve any images (didn't see an option for PPP).
 
 Even after formatting the hard drive under the floppy39.s floppy, the 
 floppyC39.fs floppy chokes on the hard drive.
 
 Is there any way to combine the two capabilities?  I.e. dropping to the 
 shell, 

Do you know if either or both of those recognize your CD? If so, you can
download the install sets and burn them on CD, and do your install from
there w/out ethernet. If you've got access to a burner that's probably
the simpler way to go. Or try out the Xircom and see if it works.

-- 
Darrin Chandler|  Phoenix BSD Users Group
[EMAIL PROTECTED]   |  http://bsd.phoenix.az.us/
http://www.stilyagin.com/  |



Re: ipv6 in openbsd 3.9

2006-06-08 Thread Rogier Krieger

On 6/8/06, Lars Hansson [EMAIL PROTECTED] wrote:

How I wish it was as easy with APNIC [...]


Well, I'd say Google is your friend. The process at APNIC seems pretty
similar to RIPE's. At least, it does so at first glance.

Through Googling for obtain apnic person object, I end up at:
http://sfc-cpu.ai3.net/v6/document/requestform.html

Which leads to: http://www.apnic.net/apnic-bin/person.pl

Cheers,

Rogier
--
If you don't know where you're going, any road will get you there.



Re: Which free board software for PostgeSQL?

2006-06-08 Thread Alexander Farber

I use PunBB 1.2.12 with -current OpenBSD and
postgresql from ports here: http://preferans.de/

On 6/7/06, Michael Lechtermann [EMAIL PROTECTED] wrote:

anyone can recommend a free PHP board/forums software for use with
PostgreSQL 8.x?




Toshiba Tecra 8000 xorg.conf

2006-06-08 Thread Joshua Sandbrook
Gidday... 

Anyone out there running 3.9 on a Toshiba Tecra 8000 ? Im trying to get it to 
run at 1024x768 but its being grumpy.

Dmesg for good measure:



OpenBSD 3.9 (GENERIC) #617: Thu Mar  2 02:26:48 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II (GenuineIntel 686-class, 512KB L2 cache) 233 MHz
cpu0: 
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem  = 167288832 (163368K)
avail mem = 145674240 (142260K)
using 2067 buffers containing 8466432 bytes (8268K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(63) BIOS, date 12/30/99
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 26%
apm0: AC on, battery charge low, charging, estimated 0:37 hours
apm0: flags 20102 dobusy 0 doidle 1
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc/0xc000 0xe8000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Intel 82443BX rev 0x02
vga1 at pci0 dev 4 function 0 Neomagic Magicgraph NM2200 rev 0x12
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 5 function 0 Intel 82371AB PIIX4 ISA rev 0x02
pciide0 at pci0 dev 5 function 1 Intel 82371AB IDE rev 0x01: DMA, channel 0 
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2030AT
wd0: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: TEAC, CD-224E, 7.5A SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 5 function 2 Intel 82371AB USB rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 5 function 3 Intel 82371AB Power rev 0x02: SMI
iic0 at piixpm0
admtemp0 at iic0 addr 0x4e: adm1021
Toshiba Fast Infrared Type O rev 0x23 at pci0 dev 9 function 0 not 
configured
cbb0 at pci0 dev 11 function 0 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map: 
no mapping for pin A
: couldn't map interrupt
cbb1 at pci0 dev 11 function 1 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map: 
no mapping for pin B
: couldn't map interrupt
isa0 at pcib0
isadma0 at isa0
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 26%
apm0: AC on, battery charge low, charging, estimated 0:37 hours
apm0: flags 20102 dobusy 0 doidle 1
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc/0xc000 0xe8000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Intel 82443BX rev 0x02
vga1 at pci0 dev 4 function 0 Neomagic Magicgraph NM2200 rev 0x12
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 5 function 0 Intel 82371AB PIIX4 ISA rev 0x02
pciide0 at pci0 dev 5 function 1 Intel 82371AB IDE rev 0x01: DMA, channel 0 
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2030AT
wd0: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: TEAC, CD-224E, 7.5A SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 5 function 2 Intel 82371AB USB rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 5 function 3 Intel 82371AB Power rev 0x02: SMI
iic0 at piixpm0
admtemp0 at iic0 addr 0x4e: adm1021
Toshiba Fast Infrared Type O rev 0x23 at pci0 dev 9 function 0 not 
configured
cbb0 at pci0 dev 11 function 0 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map: 
no mapping for pin A
: couldn't map interrupt
cbb1 at pci0 dev 11 function 1 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map: 
no mapping for pin B
: couldn't map interrupt
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
sb0 at isa0 port 0x220/24 irq 5 drq 1: dsp v3.01
midi0 at sb0: SB MIDI UART
audio0 at sb0
opl0 at sb0: model OPL3
midi1 at opl0: SB Yamaha OPL3
wss0 at isa0 port 0x530/8 irq 10 drq 0: CS4231 or AD1845 (vers 4)
audio1 at wss0
pcppi0 at isa0 port 0x61
midi2 at pcppi0: PC speaker
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
pcic0 at isa0 port 0x3e0/2 iomem 0xd/65536
pcic0 controller 0: 

Re: Linksys USB200M device boot-time troubleshooting,

2006-06-08 Thread Fred Crowson

Chris Smith wrote:

N00b here.
My Linksys USB200M, which should use the axe driver, isn't recognized at
boot.
In dmesg, I have:
 uhub3: port2, set config at addr 2 failed
 uhub3: device problem, disabling port 2
Request some references to investigate.  The documentation is great, but I'm
not seeing where I need to go to troubleshoot.  The USB subsystem has to be
initialized before ifconfig axe0, right?
Thanks,
Chris


Hi Chris,

My crystal ball is not working - but a dmesg(8) and the output of 
usbdevs -dv might help.


Fred
--
http://www.crowsons.net/puters/zaurus.php



entering custom AT commands into ppp.conf

2006-06-08 Thread Marius Van Deventer - Umzimkulu
Hi all.
 
By asking this queston i admit that i have no idea how ppp.conf works.
For a normal modem i am able to configure it fine, but for this problem
i have to admit that i have no idea. I found some hits on google but
nothing specific.
 
I managed (finally) to get gprs working on OpenBSD using my Nokia 6680.
Apart from some defalt route issues it works fine.
 
But...
 
I have to enter the init strings manually using minicom before i dial.
 
i enter:
 
ATZ
 
and then
 
AT+CGDCONT=1,IP,internet
 
then i exit minicom with no reset (ctrl-a q) and dial.
 
 
Obviously there HAS to be a way to include these in ppp.conf. All my
attempts have failed.
 
I'm sorry for the newbie-like question. Please direct answers to the
list and flames to my private address :-)
 
Cheers
 
Marius Van Deventer 
Computer Technician

Bytes Technology Group : Systems Integration 

Tel : +27 39 682 4202 | Fax : +27 39 682 4126 | Cell : +27 82 321 6491 

Email : [EMAIL PROTECTED]
Web  : www.btgroup.co.za outbind://44/www.btgroup.co.za  | Press
Office : www.itweb.co.za/office/bytes
outbind://44/www.itweb.co.za/office/bytes  | Licensing :
www.purelicensing.co.za outbind://44/www.purelicensing.co.za  

Bytes Systems Integration (Pty) Ltd : Registration No: 1995/012031/07
A subsidiary of Bytes Technology Group SA (Pty) Ltd, In association with
KAGISO
P O Box 4004, Umhlanga, 4350 ,55 Island Circle, Riverhorse Valley, Nandi
Drive, South Africa.

E-mail Disclaimer: http://www.altron.co.za/email.asp Or phone: (+27)
(11) 205-7000

by Symantec Mail Security for the presence of any viruses.

**

 0 

[demime 1.01d removed an attachment of type application/x-pkcs7-signature which 
had a name of smime.p7s]



Re: Toshiba Tecra 8000 xorg.conf

2006-06-08 Thread Paul de Weerd
Hi Joshua,

On Thu, Jun 08, 2006 at 07:39:15PM +1200, Joshua Sandbrook wrote:
| Anyone out there running 3.9 on a Toshiba Tecra 8000 ? Im trying to get it
to
| run at 1024x768 but its being grumpy.

Check http://www.openbsd.org/i386-laptop.html - the machine is listed
there with several tips on how to get it working. Xorg did not require
any config for me (Just Works (tm)).

Cheers,

Paul 'WEiRD' de Weerd

--
[++-]+++.+++[---].+++[+
+++-].++[-]+.--.[-]
 http://www.weirdnet.nl/

[demime 1.01d removed an attachment of type application/pgp-signature]



Re: Toshiba Tecra 8000 xorg.conf

2006-06-08 Thread Fred Crowson

Joshua Sandbrook wrote:
Gidday... 

Anyone out there running 3.9 on a Toshiba Tecra 8000 ? Im trying to get it to 
run at 1024x768 but its being grumpy.


Dmesg for good measure:



What are the errors in your Xorg.0.log?

And searching MARC gave:

http://marc.theaimsgroup.com/?l=openbsd-miscm=110691734923937

Which seems to indicate that it should just work...

HTH

Fred
--
http://www.crowsons.net/puters/zaurus.php



Re: Toshiba Tecra 8000 xorg.conf

2006-06-08 Thread Joshua Sandbrook
Yeah I saw that. But xorg does not just 'work by default' at 1024x768 for me. 
It just runs at 800x600 and it seems thats all it can be bothered doing right 
now...



On Thursday 08 June 2006 19:59, you wrote:
 Hi Joshua,

 On Thu, Jun 08, 2006 at 07:39:15PM +1200, Joshua Sandbrook wrote:
 | Anyone out there running 3.9 on a Toshiba Tecra 8000 ? Im trying to get
 | it to run at 1024x768 but its being grumpy.

 Check http://www.openbsd.org/i386-laptop.html - the machine is listed
 there with several tips on how to get it working. Xorg did not require
 any config for me (Just Works (tm)).

 Cheers,

 Paul 'WEiRD' de Weerd



Re: Toshiba Tecra 8000 xorg.conf

2006-06-08 Thread Bachman Kharazmi

This is not a obsd related question.

First make sure your screen and card can make that resolution.
Then include your xorg.conf and the Xorg log.

Please read the examples included first, and see if Xorg -configure can help.
here is what it can look like http://bkw.lindesign.se/tmp/xorg.conf
(for a acer tm 662)

don't forget to read
http://outlands.ca/linux/t8000.html
http://ruby2shoes.sourceforge.net/xbox/laptops/linuxOnTecra8000.html
http://www.geocities.com/goodjewishboy/tecra8000linux.html

I found things like..
X resolution
After installation, X resolution is stuck at 640x480. I have not found
the cause, but I have been suggested a workaround that fix the
problem. Add the following line to the Monitor section of
/etc/X11/xorg.conf :
   HorizSync   36-52
   VertRefresh 36-60


/bkw
On 08/06/06, Joshua Sandbrook [EMAIL PROTECTED] wrote:

Gidday...

Anyone out there running 3.9 on a Toshiba Tecra 8000 ? Im trying to get it to
run at 1024x768 but its being grumpy.

Dmesg for good measure:



OpenBSD 3.9 (GENERIC) #617: Thu Mar  2 02:26:48 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II (GenuineIntel 686-class, 512KB L2 cache) 233 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem  = 167288832 (163368K)
avail mem = 145674240 (142260K)
using 2067 buffers containing 8466432 bytes (8268K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(63) BIOS, date 12/30/99
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 26%
apm0: AC on, battery charge low, charging, estimated 0:37 hours
apm0: flags 20102 dobusy 0 doidle 1
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc/0xc000 0xe8000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Intel 82443BX rev 0x02
vga1 at pci0 dev 4 function 0 Neomagic Magicgraph NM2200 rev 0x12
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 5 function 0 Intel 82371AB PIIX4 ISA rev 0x02
pciide0 at pci0 dev 5 function 1 Intel 82371AB IDE rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2030AT
wd0: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: TEAC, CD-224E, 7.5A SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 5 function 2 Intel 82371AB USB rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 5 function 3 Intel 82371AB Power rev 0x02: SMI
iic0 at piixpm0
admtemp0 at iic0 addr 0x4e: adm1021
Toshiba Fast Infrared Type O rev 0x23 at pci0 dev 9 function 0 not
configured
cbb0 at pci0 dev 11 function 0 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map:
no mapping for pin A
: couldn't map interrupt
cbb1 at pci0 dev 11 function 1 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map:
no mapping for pin B
: couldn't map interrupt
isa0 at pcib0
isadma0 at isa0
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 26%
apm0: AC on, battery charge low, charging, estimated 0:37 hours
apm0: flags 20102 dobusy 0 doidle 1
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc/0xc000 0xe8000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Intel 82443BX rev 0x02
vga1 at pci0 dev 4 function 0 Neomagic Magicgraph NM2200 rev 0x12
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 5 function 0 Intel 82371AB PIIX4 ISA rev 0x02
pciide0 at pci0 dev 5 function 1 Intel 82371AB IDE rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2030AT
wd0: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: TEAC, CD-224E, 7.5A SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 5 function 2 Intel 82371AB USB rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 5 function 3 Intel 82371AB Power rev 0x02: SMI
iic0 at piixpm0
admtemp0 at iic0 addr 0x4e: adm1021
Toshiba Fast Infrared Type O rev 0x23 at pci0 dev 9 function 0 not
configured
cbb0 at pci0 dev 11 function 0 Toshiba ToPIC97 CardBus rev 0x05pci_intr_map:
no mapping for pin A
: couldn't map interrupt
cbb1 at pci0 dev 11 function 1 Toshiba ToPIC97 

Custom /bsd.rd to send in dmesgs?

2006-06-08 Thread vladas

Will devs ignore dmesgs from /bsd.rd that would resemble the -current GENERIC
/bsd (if it is possible to do so)?

I want to send in a few  dmesgs from the machines where I cannot install
OpenBSD, so I thought /bsd.rd would help.



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Pete Vickers

Hi,

Here's my configs, should give you some hints..

mobile phone is connected to 'COM1' at 57600baud, adding a system  
default route via the new ppp link, and automatically redialing  
immediately after link failure:


=/etc/ppp/peers/ISP
/dev/tty00
57600
defaultroute
debug
#kdebug 7
lock
user my_username
noauth
noccp
novj
noipdefault
persist
#demand
connect '/usr/sbin/chat -e -v -f /etc/ppp/peers/chat/ISP-gprs'
=

script to initialise modem, and dial ISP: (CFUN/CPIN... is to reset  
the phone, then enter the PIN code etc)

=/etc/ppp/peers/chat/ISP-gprs
REPORT Starting chat script...
ABORT ERROR
ABORT BUSY
ABORT 'NO CARRIER'
ABORT 'NO DIALTONE'
'' ATZ
OK AT+CFUN=1,1
OK \d\dAT+CPIN=1234
OK AT+CGDCONT=1
OK AT+CGDCONT=1,IP,my.apn.name,,0,0
OK ATD*99***1#
CONNECT
=


your ISP username  password (see pap-secrets instead if applicable):
=/etc/ppp/peers/chap-secrets
#secrets for authentication using CHAP
# clientserver  secret  IP addresses
my_username  *   my_password*
=


create the i/f at boot time, and initiate connection:
=/etc/hostname.ppp0
up
!pppd call ISP
=


To debug:
- $ sudo ifconfig ppp0 create
- $ sudo pppd dial ISP
	- tail /var/log/daemon, /var/log/chat (after syslogd.conf  
uncommenting/restart) and /etc/ppp/connection-errors




Hope this is of use.

/Pete



On 8. jun. 2006, at 08.07, Marius Van Deventer - Umzimkulu wrote:


Hi all.

By asking this queston i admit that i have no idea how ppp.conf works.
For a normal modem i am able to configure it fine, but for this  
problem

i have to admit that i have no idea. I found some hits on google but
nothing specific.

I managed (finally) to get gprs working on OpenBSD using my Nokia  
6680.

Apart from some defalt route issues it works fine.

But...

I have to enter the init strings manually using minicom before i dial.

i enter:

ATZ

and then

AT+CGDCONT=1,IP,internet

then i exit minicom with no reset (ctrl-a q) and dial.


Obviously there HAS to be a way to include these in ppp.conf. All my
attempts have failed.

I'm sorry for the newbie-like question. Please direct answers to the
list and flames to my private address :-)

Cheers

Marius Van Deventer
Computer Technician

Bytes Technology Group : Systems Integration

Tel : +27 39 682 4202 | Fax : +27 39 682 4126 | Cell : +27 82 321 6491

Email : [EMAIL PROTECTED]
Web  : www.btgroup.co.za outbind://44/www.btgroup.co.za  | Press
Office : www.itweb.co.za/office/bytes
outbind://44/www.itweb.co.za/office/bytes  | Licensing :
www.purelicensing.co.za outbind://44/www.purelicensing.co.za

Bytes Systems Integration (Pty) Ltd : Registration No: 1995/012031/07
A subsidiary of Bytes Technology Group SA (Pty) Ltd, In association  
with

KAGISO
P O Box 4004, Umhlanga, 4350 ,55 Island Circle, Riverhorse Valley,  
Nandi

Drive, South Africa.

E-mail Disclaimer: http://www.altron.co.za/email.asp Or phone: (+27)
(11) 205-7000

by Symantec Mail Security for the presence of any viruses.

**


0 


[demime 1.01d removed an attachment of type application/x-pkcs7- 
signature which had a name of smime.p7s]




Re: Wireless card use

2006-06-08 Thread Andy Hayward

On 6/7/06, Gaby vanhegan [EMAIL PROTECTED] wrote:

The reviews seem to rate them, it's listed as supported hardware and
it's less than #30.  Any reason I shouldn't get one of these to go
with a 3.9 box?


Edimax EW-7128G

http://www.scan.co.uk/Products/ProductInfo.asp?WebProductID=152539

-- ach



Re: OpenOffice.org 2.0 works on OpenBSD

2006-06-08 Thread Nikolaus Hiebaum
On June 6, 2006 00:44, Tobias Ulmer wrote:

 Search the ports@ mailing list, there's a port for it.

Thanks for the tip and also for the link with instructions. Yes, I was
able to underatand it.  :-) The title of the site chruetertee.ch,
however, took me some more time. :-

I found something
http://marc.theaimsgroup.com/?l=openbsd-portsm=114289306831495w=2 on
ports. ;-) I assume the proper way then would be to download this
tgz-file, put it in /ports, and then build it the usual way?

-- 
Beste Gr|_e / Best regards,
Nikolaus Hiebaum



Re: OpenOffice.org 2.0 works on OpenBSD

2006-06-08 Thread Nikolaus Hiebaum
On Thu, June 8, 2006 00:44, Bob Beck wrote:
 ...
 I use OpenOffice with sudo soffice.bin
 ..

 Shudder. My glasses just went dark. That's fucking terrifying.

 Seriously dude, You are begging for a security problem doing this.

Thank you for pointing this out to me. If you have perused my previous
message, it surely will not have slipped your attention that running
OpenOffice without the sudo command causes OpenOffice to freeze when
saving or not allowing me to save at all.

Hence, if your glasses are bright (?) again, maybe you have a useful
suggestion on how to remedy the situation. ;-)


-- 
Beste Gr|_e / Best regards,
Nikolaus Hiebaum



Re: state table, loopback and redirection

2006-06-08 Thread Camiel Dobbelaar
On Thu, 8 Jun 2006, uc.sheda wrote:
 When 172.16.218.129 is trying to reach the port 21/tcp of 129.128.5.191, 
 here is what happen:
 
 * tcpdump -tei pflog0 port 21 or 8021: don't show anything

You don't have log on your rdr pass line.

 * tcpdump -tni bridge0 port 21 or 8021: just show the SYN coming from 
 172.16.218.129, 
 nothing else.
 * pfctl -ss show 2 states:
all tcp 127.0.0.1:8021 - 129.128.5.191:21 - 172.16.218.129:22585 
CLOSED:SYN_SENT
all tcp 172.16.218.129:22585 - 127.0.0.1:8021 SYN_SENT:CLOSED
 * netstat -anp tcp show that ftp-proxy is listening on 127.0.0.1:8021 but 
 don't 
 receive anything (no socket in a state !=LISTEN with port 8021).
 
 Is there something I'm missing? What is the exact meaning of the arrows seen 
 in the 
 pfctl -ss output?

You can't connect to the internet with a private space (172.16) address.

--
Cam



Re: Wireless card use

2006-06-08 Thread Dries Schellekens

Jonathan Gray wrote:


The third is based on a TI ACX chip which can be picked by
its blue PCB.
http://kbserver.netgear.com/products/WG311v3.asp


Is this likely to be supported by OpenBSD? Is TI still refusing to 
permit the distribution of the firmware blob?


Linux people seem to have figured out that including a driver for this 
chip could have some legal issues: http://kerneltrap.org/node/6692



Cheers,

Dries



Announcing OpenBSD/amd64 Xen port

2006-06-08 Thread Mathieu Ropert

Hi,

I've been working toward porting OpenBSD/amd64 for the Xen Virtual 
Machine Monitor for a few months.

It's not 100% complete, but most is already working for domU.

Here's a list of the current issues/missing things:
- virtual NIC driver is not fonctionnal, some part of the code still 
needs to be fixed for packet transfer from/to Xen to work.
- events/clock issue: there seems to be a race condition leading to 
clock not ticking, hence putting system to sleep till a 
keyboard/network/disk interrupt is received.

- SMP is currently not supported.

I'll make a kernel binary, a disk image and sources available shortly.

Regards,
Mathieu



ntp on soekris

2006-06-08 Thread Pailloncy Jean-Gerard

Hi,

I have some flapping in ntp on soekris.
Is it important ?

First soekris (auto reboot each 15 and 45 minutes)
Jun  8 06:17:46 r001 ntpd[17515]: adjusting local clock by 0.364500s
Jun  8 06:47:45 r001 ntpd[26194]: adjusting local clock by 0.439883s
Jun  8 07:17:41 r001 ntpd[22494]: adjusting local clock by 0.513877s
Jun  8 07:47:43 r001 ntpd[30227]: adjusting local clock by 0.585656s
Jun  8 08:17:42 r001 ntpd[4523]: adjusting local clock by 0.661055s
Jun  8 08:47:44 r001 ntpd[23534]: adjusting local clock by -0.270700s
Jun  8 09:17:41 r001 ntpd[26488]: adjusting local clock by -0.191056s
Jun  8 09:47:46 r001 ntpd[23319]: adjusting local clock by 0.875716s
Jun  8 09:51:26 r001 ntpd[23319]: adjusting local clock by 0.816038s
Jun  8 09:55:43 r001 ntpd[23319]: adjusting local clock by -0.320128s
Jun  8 09:59:52 r001 ntpd[23319]: adjusting local clock by -0.695182s
Jun  8 10:01:35 r001 ntpd[23319]: adjusting local clock by -0.338598s
Jun  8 10:05:18 r001 ntpd[23319]: adjusting local clock by 0.156039s

Second soekris (auto reboot each 00 and 30 minutes)
Jun  8 05:32:29 r002 ntpd[22037]: adjusting local clock by 0.915120s
Jun  8 05:36:37 r002 ntpd[22037]: adjusting local clock by 0.626073s
Jun  8 05:40:54 r002 ntpd[22037]: adjusting local clock by -0.447298s
Jun  8 05:44:06 r002 ntpd[22037]: adjusting local clock by -0.466533s
Jun  8 05:47:34 r002 ntpd[22037]: adjusting local clock by 0.135212s
Jun  8 05:58:51 r002 ntpd[22037]: adjusting local clock by 0.131027s
Jun  8 06:02:45 r002 ntpd[15955]: adjusting local clock by 0.961918s
Jun  8 06:32:26 r002 ntpd[22591]: adjusting local clock by 1.017864s
Jun  8 07:02:31 r002 ntpd[21007]: adjusting local clock by 1.060575s
Jun  8 07:05:36 r002 ntpd[21007]: adjusting local clock by 0.529033s
Jun  8 07:29:34 r002 ntpd[21007]: adjusting local clock by -0.530499s
Jun  8 08:02:27 r002 ntpd[787]: adjusting local clock by 1.159095s
Jun  8 08:32:29 r002 ntpd[24889]: adjusting local clock by 0.204871s
Jun  8 09:02:27 r002 ntpd[12635]: adjusting local clock by 0.255003s
Jun  8 09:32:28 r002 ntpd[17403]: adjusting local clock by 0.302008s
Jun  8 10:02:29 r002 ntpd[11060]: adjusting local clock by 0.353288s

I have some other soekris, and I never have so many log message. On  
these others box there are a adjusting message once by week or once  
a day.

There are too many back and forward adjustements too close in time.

Notice: The auto reboot is done by cron. I just do that because I  
test my redundant firewall.


I may accept that during reboot the RTC lost it accuracy
But if I take a slice a 30 minutes between 2 reboots, there are  
strange thing:

Jun  8 09:47:46 r001 ntpd[23319]: adjusting local clock by 0.875716s
Jun  8 09:51:26 r001 ntpd[23319]: adjusting local clock by 0.816038s
Jun  8 09:55:43 r001 ntpd[23319]: adjusting local clock by -0.320128s
Jun  8 09:59:52 r001 ntpd[23319]: adjusting local clock by -0.695182s
Jun  8 10:01:35 r001 ntpd[23319]: adjusting local clock by -0.338598s
Jun  8 10:05:18 r001 ntpd[23319]: adjusting local clock by 0.156039s
It looks like the correction may have been done twice (0.875716s and  
0.816038s)

Too much in one direction, then (-0.320128s, -0.695182s, -0.338598s)
The sum of the 5 first lines is 0.338s

Same things with

Jun  8 05:32:29 r002 ntpd[22037]: adjusting local clock by 0.915120s
Jun  8 05:36:37 r002 ntpd[22037]: adjusting local clock by 0.626073s
Jun  8 05:40:54 r002 ntpd[22037]: adjusting local clock by -0.447298s
Jun  8 05:44:06 r002 ntpd[22037]: adjusting local clock by -0.466533s
Jun  8 05:47:34 r002 ntpd[22037]: adjusting local clock by 0.135212s
Jun  8 05:58:51 r002 ntpd[22037]: adjusting local clock by 0.131027s


Cordialement,
Jean-Girard Pailloncy

 cat /etc/ntpd.conf
# $OpenBSD: ntpd.conf,v 1.7 2004/07/20 17:38:35 henning Exp $
# sample ntpd configuration file, see ntpd.conf(5)

# Addresses to listen on (ntpd does not listen by default)
#listen on *

# sync to a single server
#server ntp.example.org

# use a random selection of 8 public stratum 2 servers
# see http://twiki.ntp.org/bin/view/Servers/NTPPoolServers
servers pool.ntp.org

 dmesg
OpenBSD 3.9 (GENERIC) #617: Thu Mar  2 02:26:48 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi (Geode by NSC  
586-class) 267 MHz

cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem  = 133799936 (130664K)
avail mem = 115367936 (112664K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/41/22, BIOS32 rev. 0 @  
0xf7840

pcibios0 at bios0: rev 2.0 @ 0xf/0x1
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Cyrix GXm PCI rev 0x00
sis0 at pci0 dev 6 function 0 NS DP83815 10/100 rev 

Re: Bind popa3d to local interface only

2006-06-08 Thread Gabriel Kihlman
Michael Lechtermann [EMAIL PROTECTED] writes:

 Hi,

 I am currently setting up a POP3 server and everything is working fine.
 Also added stunnel to handle SSL connections for popa3d.

 Now I would like to permit the usage of unencrypted connections to
 popa3d to enforce connections over SSL.

 popa3d runs in standalone mode and it should stay that way since I am
 not using inetd right now. When connected to port 995 stunnel forwards
 the connection to localhost port 110.

 Because of that I just need popa3d to listen on 127.0.0.1.

Index: standalone.c
===
RCS file: /cvs/src/usr.sbin/popa3d/standalone.c,v
retrieving revision 1.10
diff -u -r1.10 standalone.c
--- standalone.c13 Mar 2005 19:29:44 -  1.10
+++ standalone.c8 Jun 2006 08:15:33 -
@@ -127,7 +127,7 @@
hints.ai_socktype = SOCK_STREAM;
hints.ai_family = af;
hints.ai_flags = AI_PASSIVE;
-   error = getaddrinfo(NULL, sbuf, hints, res0);
+   error = getaddrinfo(127.0.0.1, sbuf, hints, res0);
if (error)
return log_error(getaddrinfo);



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Stuart Henderson
 By asking this queston i admit that i have no idea how ppp.conf works.
 I have to enter the init strings manually using minicom before i dial.
 AT+CGDCONT=1,IP,internet
 
 Obviously there HAS to be a way to include these in ppp.conf. All my
 attempts have failed.

It's difficult to get the quoting just right.
Would anyone like to commit this?

Index: etc/ppp/ppp.conf.sample
===
RCS file: /data/cvsroot/OpenBSD/src/etc/ppp/ppp.conf.sample,v
retrieving revision 1.21
diff -u -r1.21 ppp.conf.sample
--- etc/ppp/ppp.conf.sample 9 Jun 2002 06:15:15 -   1.21
+++ etc/ppp/ppp.conf.sample 8 Jun 2006 10:12:24 -
@@ -101,6 +101,23 @@
  add default HISADDR
  enable dns
 
+# To connect via a GPRS device (e.g. a mobile phone), it's often
+# necessary to set the access-point name (in this case 'internet')
+# which requires quotes in the dial string. This section shows
+# the escaping required.
+#
+gprs:
+ set device /dev/cuaU0
+ set dial ABORT ERROR ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
+   \\ ATZ OK-ATZ-OK AT+CGDCONT=1,\\\IP\\\,\\\internet\\\ OK 
\\dATD\\T TIMEOUT 40 CONNECT
+ set phone *99#
+ set speed 115200
+ set login
+ set timeout 0
+ set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
+ add default HISADDR
+ enable dns
+
 #  Example segments
 #
 # The following lines may be included as part of your configuration



Re: Bind popa3d to local interface only

2006-06-08 Thread Damien Miller
On Thu, 8 Jun 2006, Gabriel Kihlman wrote:

  Because of that I just need popa3d to listen on 127.0.0.1.
 
 Index: standalone.c
 ===
 RCS file: /cvs/src/usr.sbin/popa3d/standalone.c,v
 retrieving revision 1.10
 diff -u -r1.10 standalone.c
 --- standalone.c  13 Mar 2005 19:29:44 -  1.10
 +++ standalone.c  8 Jun 2006 08:15:33 -
 @@ -127,7 +127,7 @@
   hints.ai_socktype = SOCK_STREAM;
   hints.ai_family = af;
   hints.ai_flags = AI_PASSIVE;
 - error = getaddrinfo(NULL, sbuf, hints, res0);
 + error = getaddrinfo(127.0.0.1, sbuf, hints, res0);
   if (error)
   return log_error(getaddrinfo);
 

Why go through all of this trouble when you can just run it out of
inetd(8)?

[127.0.0.1]:pop3 stream tcp  nowait root /usr/libexec/tcpd /usr/sbin/popa3d
[::1]:pop3   stream tcp6 nowait root /usr/libexec/tcpd /usr/sbin/popa3d

-d



Re: Bind popa3d to local interface only

2006-06-08 Thread Michael Lechtermann
Damien Miller schrieb:
 Why go through all of this trouble when you can just run it out of
 inetd(8)?

Why running inetd for that alone and having an additional process open
when popa3d is supposed to be able to do it alone when set to an address
in params.h?

Imho, that patch, (with my little addidional change) is how popa3d is
supposed to work.



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Marius Van Deventer - Umzimkulu
 -Original Message-
 From: Stuart Henderson [mailto:[EMAIL PROTECTED] 
 Sent: 08 June 2006 12:19 PM
 To: Marius Van Deventer - Umzimkulu
 Cc: misc@openbsd.org
 Subject: Re: entering custom AT commands into ppp.conf
 
 
  By asking this queston i admit that i have no idea how 
 ppp.conf works.
  I have to enter the init strings manually using minicom 
 before i dial.
  AT+CGDCONT=1,IP,internet
  
  Obviously there HAS to be a way to include these in 
 ppp.conf. All my
  attempts have failed.
 
 It's difficult to get the quoting just right.
 Would anyone like to commit this?
 
 Index: etc/ppp/ppp.conf.sample
 ===
 RCS file: /data/cvsroot/OpenBSD/src/etc/ppp/ppp.conf.sample,v
 retrieving revision 1.21
 diff -u -r1.21 ppp.conf.sample
 --- etc/ppp/ppp.conf.sample   9 Jun 2002 06:15:15 -   1.21
 +++ etc/ppp/ppp.conf.sample   8 Jun 2006 10:12:24 -
 @@ -101,6 +101,23 @@
   add default HISADDR
   enable dns
  
 +# To connect via a GPRS device (e.g. a mobile phone), it's often
 +# necessary to set the access-point name (in this case 'internet')
 +# which requires quotes in the dial string. This section shows
 +# the escaping required.
 +#
 +gprs:
 + set device /dev/cuaU0
 + set dial ABORT ERROR ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
 +   \\ ATZ OK-ATZ-OK 
 AT+CGDCONT=1,\\\IP\\\,\\\internet\\\ OK \\dATD\\T TIMEOUT 
 40 CONNECT
 + set phone *99#
 + set speed 115200
 + set login
 + set timeout 0
 + set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
 + add default HISADDR
 + enable dns
 +
  #  Example segments
  #
  # The following lines may be included as part of your configuration
 


Thanks Stuart. This works for me.

[demime 1.01d removed an attachment of type application/x-pkcs7-signature which 
had a name of smime.p7s]



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Felix Kronlage
On Thu, Jun 08, 2006 at 08:07:21AM +0200, Marius Van Deventer - Umzimkulu wrote:

 By asking this queston i admit that i have no idea how ppp.conf works.

for a setup with pppd, take a look here:
url: http://hazardous.org/~fkr/openbsd/openbsd_gprs_umts.html

It is for umts/gprs cards, but the same applies to modems in cell phones.

felix
-- 
GPG/PGP:   D9AC74D0 / 076E 1E87 3E05 1C7F B1A0  8A48 0D31 9BD3 D9AC 74D0
http://hazardous.org/~fkr - [EMAIL PROTECTED] - [EMAIL PROTECTED]|irc -  
FKR-RIPE
https://www.bytemine.net/ - bytemine - BSD based hosting/solutions/ideas



SMP

2006-06-08 Thread Gustavo Rios

Dear friends,

i have been having an increasing interest on OpenBSD internals. So, my
first movement was to buy some Unix books on OS design like The Design
of the 4.4BSD  .

One thing i would like to know better is about SMP. Up to now i could
not figure it out about the algorithm choice and motivation, not i can
have a good ideia about how openbsd does behave on an SMP system
compared other unices like Solaris/AIX, etc or even pretenders like
Linux.

Thank you a lot for your time and cooperation.



Re: Bind popa3d to local interface only

2006-06-08 Thread Damien Miller
On Thu, 8 Jun 2006, Michael Lechtermann wrote:

 Damien Miller schrieb:
  Why go through all of this trouble when you can just run it out of
  inetd(8)?
 
 Why running inetd for that alone and having an additional process open
 when popa3d is supposed to be able to do it alone when set to an address
 in params.h?

popa3d forks for each connection



Re: SMP

2006-06-08 Thread Marc Balmer
* Gustavo Rios wrote:
 Dear friends,
 
 i have been having an increasing interest on OpenBSD internals. So, my
 first movement was to buy some Unix books on OS design like The Design
 of the 4.4BSD  .
 
 One thing i would like to know better is about SMP. Up to now i could
 not figure it out about the algorithm choice and motivation, not i can
 have a good ideia about how openbsd does behave on an SMP system
 compared other unices like Solaris/AIX, etc or even pretenders like
 Linux.
 
 Thank you a lot for your time and cooperation.

you should read the book UNIX systems for modern architectures by carl
schimmel.  it covers the topic in-depth.  be warned, this is a rather
theoretical text (as the topic is not entry-level anyways...)

- marc balmer



Re: state table, loopback and redirection

2006-06-08 Thread Camiel Dobbelaar
On Thu, 8 Jun 2006, sheda wrote:
 There's a NAT box between the OpenBSD box and Internet, that's why I don't
 need outgoing NAT rules.

Then the ftp-proxy needs to run on the NAT box, because the private space 
address is used _inside_ the FTP protocol as well (in active mode).

For bridges ftpsesame may be what you're looking for:
http://www.sentia.org/projects/ftpsesame

--
Cam



Re: OpenOffice.org 2.0 works on OpenBSD

2006-06-08 Thread John Fiore
Is it maybe a permissions issue on the directory that OpenOffice uses as
temporary space to save your files while you're working on them?

On 6/8/06, Nikolaus Hiebaum [EMAIL PROTECTED] wrote:

 On Thu, June 8, 2006 00:44, Bob Beck wrote:
  ...
  I use OpenOffice with sudo soffice.bin
  ..
 
  Shudder. My glasses just went dark. That's fucking terrifying.
 
  Seriously dude, You are begging for a security problem doing this.

 Thank you for pointing this out to me. If you have perused my previous
 message, it surely will not have slipped your attention that running
 OpenOffice without the sudo command causes OpenOffice to freeze when
 saving or not allowing me to save at all.

 Hence, if your glasses are bright (?) again, maybe you have a useful
 suggestion on how to remedy the situation. ;-)


 --
 Beste Gr|_e / Best regards,
 Nikolaus Hiebaum



Re: b/g wifi card on wi list?

2006-06-08 Thread Stuart Henderson
On 2006/06/08 14:33, Toni Mueller wrote:
 I am also just now shopping for a good PCMCIA (or CardBus) card for
 building an accesspoint and/or a router supporting wireless LAN and
 perused www.openbsd.org/i386.html which imho lists a lot of cards, only
 to find out that most if not all of them don't seem to be available
 anymore here in Germany - at least our supplier claims so.

There are a limited number of PCMCIA/CardBus cards with external
antennas (which you're likely to want for an AP), so you might be
limited to B with the prism-based Senao/Engenius cards - wi(4) -
they're reliable in hostap mode (as long as they are running
supported firmware; see `man wi'). They seem to be quite widely
available; Wim sells them, amongst others.

If you want 11g hostap on OpenBSD, currently you need a
Ralink device. Afaik if you want a decent antenna, this means
PCI/MiniPCI (or possibly some of the USB devices).

 It would be very nice if someone had a list of good current cards...

Manufacturers change chipsets so often that maintaining this
would be a major undertaking. If you want something that works
you need to research, try cards, and when you find one
that's good, buy any more you need before the manufacturer
has chance to change design. Or buy from someone who already
did this.



Re: Which free board software for PostgeSQL?

2006-06-08 Thread Terry
On Wed, Jun 07, 2006 at 08:46:56PM +0200, Michael Lechtermann wrote:
 Hi,
 
 anyone can recommend a free PHP board/forums software for use with
 PostgreSQL 8.x?
 
 PgSQL isn't mentioned in the vBulletin homepage.
 PHPBB is supposed to work with 7.x, not sure about 8.x
 
 Thanks in advance.
 
 Michael
 

PunBB isn't bad. Look in the archives, somebody gave some instructions
how to set it up. As far as PhpBB goes, it's been plagued with
security problems.

-- 
Terry
http://tyson.homeunix.org



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Stuart Henderson
oops. Well spotted Marius.

+ set phone *99#
should have been
+ set phone *99\#

I did test it but my phone obviously didn't require the #.


Index: etc/ppp/ppp.conf.sample
===
RCS file: /data/cvsroot/OpenBSD/src/etc/ppp/ppp.conf.sample,v
retrieving revision 1.21
diff -u -r1.21 ppp.conf.sample
--- etc/ppp/ppp.conf.sample 9 Jun 2002 06:15:15 -   1.21
+++ etc/ppp/ppp.conf.sample 8 Jun 2006 10:12:24 -
@@ -101,6 +101,23 @@
  add default HISADDR
  enable dns
 
+# To connect via a GPRS device (e.g. a mobile phone), it's often
+# necessary to set the access-point name (in this case 'internet')
+# which requires quotes in the dial string. This section shows
+# the escaping required.
+#
+gprs:
+ set device /dev/cuaU0
+ set dial ABORT ERROR ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
+   \\ ATZ OK-ATZ-OK AT+CGDCONT=1,\\\IP\\\,\\\internet\\\ OK 
\\dATD\\T TIMEOUT 40 CONNECT
+ set phone *99\#
+ set speed 115200
+ set login
+ set timeout 0
+ set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
+ add default HISADDR
+ enable dns
+
 #  Example segments
 #
 # The following lines may be included as part of your configuration



Re: ntp on soekris

2006-06-08 Thread Pailloncy Jean-Gerard

Jun  8 09:47:46 r001 ntpd[23319]: adjusting local clock by 0.875716s
Jun  8 09:51:26 r001 ntpd[23319]: adjusting local clock by 0.816038s


Note that the time shown is *not* the time being adjusted,
but the difference from true time.

I.e at first the offset is 0.87s and later it is only 0.81s so it is
slowly getting there.

Ok. Sorry to misunderstand the numbers.

I do some calculation in spreadsheet.
The skew is between -10.7 and 3.7 milliseconds/second.

The man page of adjtime says:
 delta is positive, a larger increment than normal is used.   
The skew used
 to perform the correction is generally a fraction of one  
percent.  Thus,


An average correction of 10.7 milliseconds in 1 seconds during 4  
minutes is larger than a fraction of one percent. I wonder if my  
understanding is correct, and why the skew is so fast.

And last question, is it a real problem ?

time: time in log file
adjusting: number in second in adjusting by message
unnamed column: delta in time and in off second
skew: speed of the correction.
time  adjusting  skew (ms/s)
00:14:04   0.161853
00:17:47   0.914204   223.00   0.752351   3.3738
00:21:30   0.912827   223.00  -0.001377  -0.0062
01:47:43   0.135143  5173.00  -0.777684  -0.1503
02:17:44   1.207917  1801.00   1.072774   0.5957
02:47:42   1.281030  1798.00   0.073113   0.0407
03:17:41   0.356476  1799.00  -0.924554  -0.5139
03:47:42   0.429416  1801.00   0.072940   0.0405
03:51:22   0.213789   220.00  -0.215627  -0.9801
03:58:06  -0.164806   404.00  -0.378595  -0.9371
04:17:44   0.507832  1178.00   0.672638   0.5710
04:49:11   1.575442  1887.00   1.067610   0.5658
05:17:43   0.660218  1712.00  -0.915224  -0.5346
05:47:44   0.728825  1801.00   0.068607   0.0381
06:17:39   0.798930  1795.00   0.070105   0.0391
06:22:00   0.240950   261.00  -0.557980  -2.1379
06:29:28  -0.242509   448.00  -0.483459  -1.0791
06:33:51  -0.164418   263.00   0.078091   0.2969
07:47:46   1.024516  4435.00   1.188934   0.2681
08:17:44   1.101519  1798.00   0.077003   0.0428
08:47:49   0.173583  1805.00  -0.927936  -0.5141
09:17:53   0.247539  1804.00   0.073956   0.0410
09:47:42   0.318959  1789.00   0.071420   0.0399
10:17:53   1.392653  1811.00   1.073694   0.5929
10:47:43   0.474007  1790.00  -0.918646  -0.5132
11:17:44   0.540287  1801.00   0.066280   0.0368
11:47:45  -0.375363  1801.00  -0.915650  -0.5084
11:51:34  -0.172898   229.00   0.202465   0.8841
12:17:41   0.69  1567.00   0.869564   0.5549
12:21:22   0.520937   221.00  -0.175729  -0.7952
12:25:03  -0.132391   221.00  -0.653328  -2.9562
12:36:28  -0.429008   685.00  -0.296617  -0.4330
12:47:44   0.764023   676.00   1.193031   1.7648
12:50:50   0.759465   186.00  -0.004558  -0.0245
13:17:45   0.844410  1615.00   0.084945   0.0526
13:22:01   0.426703   256.00  -0.417707  -1.6317
13:25:38  -0.218589   217.00  -0.645292  -2.9737
13:32:25  -0.390765   407.00  -0.172176  -0.4230
13:47:43   0.925055   918.00   1.315820   1.4334
15:17:46   0.150131  5403.00  -0.774924  -0.1434
15:47:46   0.212621  1800.00   0.062490   0.0347
16:17:47   0.296601  1801.00   0.083980   0.0466
16:47:45   0.373255  1798.00   0.076654   0.0426
17:17:48   0.444087  1803.00   0.070832   0.0393
17:47:45   0.519118  1797.00   0.075031   0.0418
18:17:47   0.594991  1802.00   0.075873   0.0421
18:47:49   0.666787  1802.00   0.071796   0.0398
18:50:50   0.663644   181.00  -0.003143  -0.0174
19:17:40  -0.262104  1610.00  -0.925748  -0.5750
19:21:54  -0.143448   254.00   0.118656   0.4671
19:47:43   0.815742  1549.00   0.959190   0.6192
19:51:29   0.805368   226.00  -0.010374  -0.0459
19:55:34  -0.401787   245.00  -1.207155  -4.9272
19:59:53  -0.688805   259.00  -0.287018  -1.1082
20:01:11  -0.39866078.00   0.290145   3.7198
20:17:45   0.889891   994.00   1.288551   1.2963
20:21:45   0.637197   240.00  -0.252694  -1.0529
20:26:06  -0.410787   261.00  -1.047984  -4.0153
20:28:58  -0.505440   172.00  -0.094653  -0.5503
20:31:34  -0.208699   156.00   0.296741   1.9022
20:37:11   0.402252   337.00   0.610951   1.8129
20:47:42   0.964681   631.00   0.562429   0.8913
20:51:24   0.960566   222.00  -0.004115  -0.0185
21:02:36  -0.873072   672.00  -1.833638  -2.7286
21:05:56  -0.527576   200.00   0.345496   1.7275
21:09:39   0.131954   223.00   0.659530   2.9575
21:17:42   1.033462   483.00   0.901508   1.8665
21:47:44   1.104782  1802.00   0.071320   0.0396
22:17:43   0.184729  1799.00  -0.920053  -0.5114
22:47:47   0.254301  1804.00   0.069572   0.0386
23:17:55   1.340637  1808.00   1.086336   0.6008
23:19:24   1.33359889.00  -0.007039  -0.0791
23:23:33  -1.336042   249.00  -2.669640 -10.7214
23:26:58  -0.690752   205.00   0.645290   3.1478
23:47:42   0.408653  1244.00   1.099405   0.8838
23:51:12   0.354902   210.00  -0.053751  -0.2560
23:55:15  -0.357164   243.00  -0.712066  -2.9303
23:58:46  -0.138396   211.00   0.218768   1.0368
00:17:45   0.479970  1139.00   0.618366   0.5429
00:47:48   0.559100  1803.00   0.079130   0.0439
01:17:46  

Re: Custom /bsd.rd to send in dmesgs?

2006-06-08 Thread Nick Holland

vladas wrote:
Will devs ignore dmesgs from /bsd.rd that would resemble the -current 
GENERIC

/bsd (if it is possible to do so)?

I want to send in a few  dmesgs from the machines where I cannot install
OpenBSD, so I thought /bsd.rd would help.


There are a lot of reasons why developers want the dmesgs -- a major 
reason is to find out how the GENERIC kernel sees the hardware, another 
is to get reports of how it actually works with that hardware.


A custom kernel does neither of those tasks.  Simply booting bsd.rd 
(even an official one) doesn't answer either very well...what happens if 
a probe of something in GENERIC that isn't in bsd.rd causes the machine 
to lock?  What happens if the disk interface is properly recognized..but 
doesn't work properly?  You would never know if you didn't actually do 
the install.  The lack of a didn't work! message might cause someone 
to think it did...


Perhaps even more tantalizing, what if a problem IS seen in the 
dmesg...if you can't install, you can't test a fix.


So..I suspect you won't get a lot of excited responses from developers, 
in general.  Or I could be wrong...


Nick.



Problem logging in.

2006-06-08 Thread Jonas Lindskog
Hello,

A week ago my open bsd firewall started to show a very strange behaviour.
I have the ssh-daemon running and ususally log-in remotely to be able to
administrate the pf.conf file. But now I cant log in. Ok, maybe I've just
forgott my password. I booted in single user mode and changed it, then
booted normally but couldn't log in anyway. I booted in single user mode
again changed it to another password, changed to another user (using su)
and then changed user to root again (again using su). Was prompted for the
password, entered it and login was again rejected. When i tried to change
the password it complained that something was wrong with a file called
/etc/master.passwd. When looking at the file it contained parts of my
pf.conf file.

Have I've been hacked or is it just a major error done from my side.

I understand that the information probably isn't enough but if someone
could guide me further I would be very happy.

regards
Jonas Lindskog



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Stuart Henderson
hmmm. Was right the first time with *99# - not sure why you
needed *99\# then Marius...



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Marius Van Deventer - Umzimkulu
 -Original Message-
 From: Stuart Henderson [mailto:[EMAIL PROTECTED] 
 Sent: 08 June 2006 04:17 PM
 To: Marius Van Deventer - Umzimkulu
 Cc: misc@openbsd.org
 Subject: Re: entering custom AT commands into ppp.conf
 
 
 hmmm. Was right the first time with *99# - not sure why you
 needed *99\# then Marius...
 

When I tried *99# my phone's display read Dialling *99 and then
Disconnecting *99 shortly after.

Changing it to *99\# results in the phone simply connecting without any
message at all. The only change is the double arrow icon in the corner
telling you you're connected (nokia 6680).


After that, I can browse the web, ping sites etc...

It is probably a quirk of the service provider. Each provider probably
has a different number.

Some users are required to enter a Pin number command to activate the
phones, others need usernames and passwords.
I just needed the number and the at+ command that chooses the right
acess point.

[demime 1.01d removed an attachment of type application/x-pkcs7-signature which 
had a name of smime.p7s]



Re: ipv6 in openbsd 3.9

2006-06-08 Thread Jeroen Massar
On Thu, 2006-06-08 at 02:40 +, Lars Hansson wrote:
[..]
 I wanted to try SixXs but I dont have an apnic (or other rir) handle.

I guess you missed http://www.sixxs.net/signup/create/
Of course, if you are in APNIC area it is much wiser to use a broker
from that area, see http://www.sixxs.net/tools/aiccu/brokers/ for a
large list of them which should encompass all. Unfortunately there have
not been any offers from that area yet to get one up and running.

Greets,
 Jeroen

[demime 1.01d removed an attachment of type application/pgp-signature which had 
a name of signature.asc]



Re: entering custom AT commands into ppp.conf

2006-06-08 Thread Stuart Henderson
On 2006/06/08 16:37, Marius Van Deventer - Umzimkulu wrote:
 When I tried *99# my phone's display read Dialling *99 and then
 Disconnecting *99 shortly after.

Did you have it in quotes as in my example?

 It is probably a quirk of the service provider. Each provider probably
 has a different number.

AIUI the PPP session is actually with the phone, rather than
with the provider.



Lockups and Semop panics

2006-06-08 Thread Michael Erdely

Hi,

I've got a Dell Dimension XPS B866r desktop running as my web/mail 
server (recently upgraded to 3.9).


Occasionally, after a seemingly random amount of time, the machine will 
do one of two things: it will either lockup/freeze where there are no 
messages on the console, but you cannot type, ping or access the box in 
any way (but the reset button) OR, since I have ddb.panic=0, it will 
reboot with the following message from my serial console:

panic: semop - can't undo undos
Starting stack trace...panic(fff4,3,e870df10,2,fff4) at 
panic+0x71panic(d051c1f6,e870dec8,12,d6a4f2d0,3) at panic+0x71
sys_semop(d658b2f0,e870df68,e870df58,0,1998c) at 
sys_semop+0x492syscall() at syscall+0x2ea

--- syscall (number 290) ---0x444e4e9:
End of stack trace.
syncing disks... 19 19 donerebooting...

Since the box rebooted automatically, I don't have ps output, but the 
box is running: stock GENERIC kernel, mysql-server-5.0.22, stock apache 
(chrooted) w/ ssl, courier-imap/pop3 w/ssl, imap-proxy, 
php5-core,curl,gd,imap,mbstring,mcrypt,mysql-5.1.4-hardened (compiled 
from CVS ports of -current), wordpress-2.0.3, gallery-2.1.1, 
squirrelmail 1.4.6 and 1.5.1, spamd (openbsd), spamassassin 
(spamc+spamd+procmail), clamav (clamav-milter + clamd), sendmail (with 
sasl compiled in), sasl with mysql+crypt patch applied, pure-ftpd 
(requiring ssl... not really used).


When the box comes back up, none of the log files have error messages.

Let me know if I can provide any more info.
Does anyone have any thoughts?  I'm thinking that I'm running too much 
on my P3-866 w/ 512 MB RAM and should set up another box to offload 
either mail, apache or mysql.


Below is a dmesg.

Thanks.

OpenBSD 3.9 (GENERIC) #617: Thu Mar  2 02:26:48 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (GenuineIntel 686-class) 865 MHz
cpu0: 
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE

real mem  = 536190976 (523624K)
avail mem = 482246656 (470944K)
using 4278 buffers containing 26910720 bytes (26280K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 03/29/01, BIOS32 rev. 0 @ 0xfda74
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf/0x1
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf3250/208 (11 entries)
pcibios0: PCI Interrupt Router at 000:31:0 (Intel 82371FB ISA rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc/0x8000 0xc8000/0x800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Intel 82820 MCH rev 0x03: rng active, 
8Kb/sec

ppb0 at pci0 dev 1 function 0 Intel 82820 AGP rev 0x03
pci1 at ppb0 bus 1
ppb1 at pci0 dev 30 function 0 Intel 82801AA Hub-to-PCI rev 0x02
pci2 at ppb1 bus 2
vga1 at pci2 dev 8 function 0 S3 Trio32/64 rev 0x53
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
xl0 at pci2 dev 11 function 0 3Com 3c905C 100Base-TX rev 0x74: irq 10, 
address 00:50:da:b6:52:f9

bmtphy0 at xl0 phy 24: Broadcom 3C905C internal PHY, rev. 6
ichpcib0 at pci0 dev 31 function 0 Intel 82801AA LPC rev 0x02
pciide0 at pci0 dev 31 function 1 Intel 82801AA IDE rev 0x02: DMA, 
channel 0 wired to compatibility, channel 1 wired to compatibility

wd0 at pciide0 channel 0 drive 0: ST330630A
wd0: 16-sector PIO, LBA, 29188MB, 59777640 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
wd1 at pciide0 channel 1 drive 0: ST330013A
wd1: 16-sector PIO, LBA, 28629MB, 58633344 sectors
atapiscsi0 at pciide0 channel 1 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: HITACHI, DVD-ROM GD-5000, 0212 SCSI0 
5/cdrom removable

wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4
cd0(pciide0:1:1): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 31 function 2 Intel 82801AA USB rev 0x02: irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ichiic0 at pci0 dev 31 function 3 Intel 82801AA SMBus rev 0x02: irq 9
iic0 at ichiic0
unknown at iic0 addr 0x18 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ef6d netmask ef6d ttymask ffef
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81

Re: Lockups and Semop panics

2006-06-08 Thread Otto Moerbeek
On Thu, 8 Jun 2006, Michael Erdely wrote:

 Hi,
 
 I've got a Dell Dimension XPS B866r desktop running as my web/mail server
 (recently upgraded to 3.9).
 
 Occasionally, after a seemingly random amount of time, the machine will do one
 of two things: it will either lockup/freeze where there are no messages on the
 console, but you cannot type, ping or access the box in any way (but the reset
 button) OR, since I have ddb.panic=0, it will reboot with the following
 message from my serial console:
 panic: semop - can't undo undos
 Starting stack trace...panic(fff4,3,e870df10,2,fff4) at
 panic+0x71panic(d051c1f6,e870dec8,12,d6a4f2d0,3) at panic+0x71
 sys_semop(d658b2f0,e870df68,e870df58,0,1998c) at sys_semop+0x492syscall() at
 syscall+0x2ea
 --- syscall (number 290) ---0x444e4e9:
 End of stack trace.
 syncing disks... 19 19 donerebooting...
 
 Since the box rebooted automatically, I don't have ps output, but the box is
 running: stock GENERIC kernel, mysql-server-5.0.22, stock apache (chrooted) w/
 ssl, courier-imap/pop3 w/ssl, imap-proxy,
 php5-core,curl,gd,imap,mbstring,mcrypt,mysql-5.1.4-hardened (compiled from CVS
 ports of -current), wordpress-2.0.3, gallery-2.1.1, squirrelmail 1.4.6 and
 1.5.1, spamd (openbsd), spamassassin (spamc+spamd+procmail), clamav
 (clamav-milter + clamd), sendmail (with sasl compiled in), sasl with
 mysql+crypt patch applied, pure-ftpd (requiring ssl... not really used).
 
 When the box comes back up, none of the log files have error messages.
 
 Let me know if I can provide any more info.
 Does anyone have any thoughts?  I'm thinking that I'm running too much on my
 P3-866 w/ 512 MB RAM and should set up another box to offload either mail,
 apache or mysql.

your system is running out of semaphore undo data structures. Try
increasing at least kern.seminfo.semmnu. Other semaphore related
sysctl's might need an increase as well.

-Otto

 
 Below is a dmesg.
 
 Thanks.
 
 OpenBSD 3.9 (GENERIC) #617: Thu Mar  2 02:26:48 MST 2006
 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
 cpu0: Intel Pentium III (GenuineIntel 686-class) 865 MHz
 cpu0:
 FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
 real mem  = 536190976 (523624K)
 avail mem = 482246656 (470944K)
 using 4278 buffers containing 26910720 bytes (26280K) of memory
 mainbus0 (root)
 bios0 at mainbus0: AT/286+(00) BIOS, date 03/29/01, BIOS32 rev. 0 @ 0xfda74
 apm0 at bios0: Power Management spec V1.2
 apm0: AC on, battery charge unknown
 apm0: flags 30102 dobusy 0 doidle 1
 pcibios0 at bios0: rev 2.1 @ 0xf/0x1
 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf3250/208 (11 entries)
 pcibios0: PCI Interrupt Router at 000:31:0 (Intel 82371FB ISA rev 0x00)
 pcibios0: PCI bus #2 is the last bus
 bios0: ROM list: 0xc/0x8000 0xc8000/0x800
 cpu0 at mainbus0
 pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
 pchb0 at pci0 dev 0 function 0 Intel 82820 MCH rev 0x03: rng active, 8Kb/sec
 ppb0 at pci0 dev 1 function 0 Intel 82820 AGP rev 0x03
 pci1 at ppb0 bus 1
 ppb1 at pci0 dev 30 function 0 Intel 82801AA Hub-to-PCI rev 0x02
 pci2 at ppb1 bus 2
 vga1 at pci2 dev 8 function 0 S3 Trio32/64 rev 0x53
 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
 wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
 xl0 at pci2 dev 11 function 0 3Com 3c905C 100Base-TX rev 0x74: irq 10,
 address 00:50:da:b6:52:f9
 bmtphy0 at xl0 phy 24: Broadcom 3C905C internal PHY, rev. 6
 ichpcib0 at pci0 dev 31 function 0 Intel 82801AA LPC rev 0x02
 pciide0 at pci0 dev 31 function 1 Intel 82801AA IDE rev 0x02: DMA, channel 0
 wired to compatibility, channel 1 wired to compatibility
 wd0 at pciide0 channel 0 drive 0: ST330630A
 wd0: 16-sector PIO, LBA, 29188MB, 59777640 sectors
 wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
 wd1 at pciide0 channel 1 drive 0: ST330013A
 wd1: 16-sector PIO, LBA, 28629MB, 58633344 sectors
 atapiscsi0 at pciide0 channel 1 drive 1
 scsibus0 at atapiscsi0: 2 targets
 cd0 at scsibus0 targ 0 lun 0: HITACHI, DVD-ROM GD-5000, 0212 SCSI0 5/cdrom
 removable
 wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4
 cd0(pciide0:1:1): using PIO mode 4, DMA mode 2
 uhci0 at pci0 dev 31 function 2 Intel 82801AA USB rev 0x02: irq 10
 usb0 at uhci0: USB revision 1.0
 uhub0 at usb0
 uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
 uhub0: 2 ports with 2 removable, self powered
 ichiic0 at pci0 dev 31 function 3 Intel 82801AA SMBus rev 0x02: irq 9
 iic0 at ichiic0
 unknown at iic0 addr 0x18 not configured
 isa0 at ichpcib0
 isadma0 at isa0
 pckbc0 at isa0 port 0x60/5
 pckbd0 at pckbc0 (kbd slot)
 pckbc0: using irq 1 for kbd slot
 wskbd0 at pckbd0: console keyboard, using wsdisplay0
 pms0 at pckbc0 (aux slot)
 pckbc0: using irq 12 for aux slot
 wsmouse0 at pms0 mux 0
 pcppi0 at isa0 port 0x61
 midi0 at pcppi0: PC speaker
 spkr0 at pcppi0
 lpt0 at isa0 port 0x378/4 irq 7
 npx0 at isa0 port 0xf0/16: using exception 16
 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte 

Re: ntp on soekris

2006-06-08 Thread knitti

On 6/8/06, Peter [EMAIL PROTECTED] wrote:


--- knitti [EMAIL PROTECTED] wrote:
 the soekris are not very good at time keeping, in my experience.
 whether this is a problem is something you have to decide, do
 you need more precision? if yes, change the hardware, else
 don't worry

What is your experience and what did you observe?  I have two 4801
units and they have no problem keeping time.


I have a couple of 4501, and they _do_ keep the time, with the help
of ntpd, random sample:
Dec 21 03:33:45 fg-router ntpd[14941]: adjusting local clock by 0.893647s
Dec 21 03:37:45 fg-router ntpd[14941]: adjusting local clock by 0.859043s
Dec 21 03:41:43 fg-router ntpd[14941]: adjusting local clock by 0.788777s
Dec 21 03:44:49 fg-router ntpd[14941]: adjusting local clock by 0.740139s
Dec 21 03:48:49 fg-router ntpd[14941]: adjusting local clock by 0.645784s
Dec 21 03:52:22 fg-router ntpd[14941]: adjusting local clock by 0.761796s
Dec 21 03:56:20 fg-router ntpd[14941]: adjusting local clock by 0.822203s
Dec 21 03:59:59 fg-router ntpd[14941]: adjusting local clock by 0.890898s
Dec 21 04:04:03 fg-router ntpd[14941]: adjusting local clock by 0.796980s
Dec 21 04:07:44 fg-router ntpd[14941]: adjusting local clock by 0.740668s
Dec 21 04:11:45 fg-router ntpd[14941]: adjusting local clock by 0.726457s
Dec 21 04:15:45 fg-router ntpd[14941]: adjusting local clock by 0.817878s
Dec 21 04:19:45 fg-router ntpd[14941]: adjusting local clock by 0.917739s
which is similiar on all of the soekris boxes

another sample from another box, not a soekris:
Jun  5 22:21:38 cvs ntpd[2002]: adjusting local clock by -0.194812s
Jun  5 23:25:42 cvs ntpd[2002]: adjusting local clock by -0.170715s
Jun  6 00:38:50 cvs ntpd[2002]: adjusting local clock by -0.131455s
Jun  6 00:50:41 cvs ntpd[2002]: adjusting local clock by -0.156146s
Jun  6 00:55:39 cvs ntpd[10045]: peer 82.133.58.132 now invalid
Jun  6 01:09:08 cvs ntpd[10045]: peer 82.133.58.132 now valid
Jun  6 01:54:22 cvs ntpd[2002]: adjusting local clock by -0.142031s
Jun  6 02:06:02 cvs ntpd[2002]: adjusting local clock by -0.153419s
Jun  6 02:14:49 cvs ntpd[2002]: adjusting local clock by -0.181421s
Jun  6 03:10:24 cvs ntpd[2002]: adjusting local clock by -0.176803s
Jun  6 04:17:09 cvs ntpd[2002]: adjusting local clock by -0.142914s
Jun  6 04:25:24 cvs ntpd[2002]: adjusting local clock by -0.131678s

which leads me to the assumption, that the soekris boxes have
drift a bit more in time. thats all.


--knitti



Re: Lockups and Semop panics

2006-06-08 Thread Michael Erdely

Otto Moerbeek wrote:

On Thu, 8 Jun 2006, Michael Erdely wrote:

panic: semop - can't undo undos


your system is running out of semaphore undo data structures. Try
increasing at least kern.seminfo.semmnu. Other semaphore related
sysctl's might need an increase as well.


Thanks, Otto.  I'll give it a shot (increased semmnu to 40 for starters).

-ME

--
Support OpenBSD: http://www.openbsd.org/orders.html



Re: ntp on soekris

2006-06-08 Thread Pailloncy Jean-Gerard

--- knitti [EMAIL PROTECTED] wrote:
 the soekris are not very good at time keeping, in my experience.
 whether this is a problem is something you have to decide, do
 you need more precision? if yes, change the hardware, else
 don't worry

What is your experience and what did you observe?  I have two 4801
units and they have no problem keeping time.

I have 3 others soekris, and they have no problem keeping time.

Cordialement,
Jean-Girard Pailloncy



Re: Lockups and Semop panics

2006-06-08 Thread Bob Beck
* Otto Moerbeek [EMAIL PROTECTED] [2006-06-08 10:00]:
 On Thu, 8 Jun 2006, Michael Erdely wrote:
 
  Hi,
  
  I've got a Dell Dimension XPS B866r desktop running as my web/mail server
  (recently upgraded to 3.9).
  
  Occasionally, after a seemingly random amount of time, the machine will do 
  one
  of two things: it will either lockup/freeze where there are no messages on 
  the
  console, but you cannot type, ping or access the box in any way (but the 
  reset
  button) OR, since I have ddb.panic=0, it will reboot with the following
  message from my serial console:
  panic: semop - can't undo undos
  Starting stack trace...panic(fff4,3,e870df10,2,fff4) at
  panic+0x71panic(d051c1f6,e870dec8,12,d6a4f2d0,3) at panic+0x71
  sys_semop(d658b2f0,e870df68,e870df58,0,1998c) at sys_semop+0x492syscall() at
  syscall+0x2ea
  --- syscall (number 290) ---0x444e4e9:
  End of stack trace.
  syncing disks... 19 19 donerebooting...
  
  Since the box rebooted automatically, I don't have ps output, but the box is
  running: stock GENERIC kernel, mysql-server-5.0.22, stock apache (chrooted) 
  w/
  ssl, courier-imap/pop3 w/ssl, imap-proxy,
  php5-core,curl,gd,imap,mbstring,mcrypt,mysql-5.1.4-hardened (compiled from 
  CVS
  ports of -current), wordpress-2.0.3, gallery-2.1.1, squirrelmail 1.4.6 and
  1.5.1, spamd (openbsd), spamassassin (spamc+spamd+procmail), clamav
  (clamav-milter + clamd), sendmail (with sasl compiled in), sasl with
  mysql+crypt patch applied, pure-ftpd (requiring ssl... not really used).
  
  When the box comes back up, none of the log files have error messages.
  
  Let me know if I can provide any more info.
  Does anyone have any thoughts?  I'm thinking that I'm running too much on my
 
 your system is running out of semaphore undo data structures. Try
 increasing at least kern.seminfo.semmnu. Other semaphore related
 sysctl's might need an increase as well.
 

And mysqueal sucks...

Your system may run out of other things as well given the bloatware
you're running on it.  anything else I have mysqeal on and any
significant amount of users I usually have to crank up quite a few of
the default limits, both in the kernel and in mysql - I usually build
a GENERIC with maxusers=128 to start, and then find the 80 bazillion
knobs in mysqeal to turn to tell it to use file descriptors. no really
use more than 100 file descriptors.  no really really use more than 
100 file descriptors

If you have a small number of users you may be fine. however
seeing what you have there and 512 mb of ram, you may want a bit more
if you have significant(1) usage.

Did I mention that mysqueal sucks?

-Bob
 
1) Your notion of significant may not be mine - Our similar boxes 
cluster a load of up to 2500 simultaneous sessions with up to 300 
click the thingy at the same time... They've all got 2 gig of ram
and there are 7 (I think atm) of them.



Re: ntp on soekris

2006-06-08 Thread Peter
--- knitti [EMAIL PROTECTED] wrote:

 On 6/8/06, Pailloncy Jean-Gerard [EMAIL PROTECTED] wrote:
  minutes is larger than a fraction of one percent. I wonder if my
  understanding is correct, and why the skew is so fast.
  And last question, is it a real problem ?
 
 the soekris are not very good at time keeping, in my experience.
 whether this is a problem is something you have to decide, do
 you need more precision? if yes, change the hardware, else
 don't worry

What is your experience and what did you observe?  I have two 4801
units and they have no problem keeping time.

Peter
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 



nfe driver and Sun X2100

2006-06-08 Thread stan
Has anyone gotten teh nfe port on a Sun 2100 to work on 19M? I have one of
these, that I am setting up as a firewall between 2 legacy networks, both
of which are 10M, and when I plug that port into the 10M hub, I get
continuing kernel error messages.

I'm considering locking it down, to se if that works, but have not tried
that yet.

-- 
U.S. Encouraged by Vietnam Vote - Officials Cite 83% Turnout Despite Vietcong 
Terror 
- New York Times 9/3/1967



Re: OpenOffice.org 2.0 works on OpenBSD

2006-06-08 Thread Nikolaus Hiebaum
* John Fiore wrote on Jun 8, 2006 [08:22, -0500] :

 Is it maybe a permissions issue on the directory that OpenOffice uses as
 temporary space to save your files while you're working on them?

I checked the settings in OpenOffice: temporary files are written to /tmp and
My Documents are written to my home directory.

The permissions of the directory where OpenOffice is installed are:
drwxr-xr-x   8 root  wheel  512 Feb 23 21:13 openoffice.org2.0

And this is the permission of
-r-xr-xr-x  1 root  wheel6818 Feb 23 21:22 soffice
-r-xr-xr-x  1 root  wheel  281780 Feb 23 21:22 soffice.bin
-r-xr-xr-x  1 root  wheel  63 Feb 23 21:13 swriter

Yes, I am member of the group wheel.


-- 
Beste Gr|_e / Best regards ,
Nikolaus Hiebaum



Re: nfe driver and Sun X2100

2006-06-08 Thread Srebrenko Sehic

On 6/8/06, stan [EMAIL PROTECTED] wrote:

Has anyone gotten teh nfe port on a Sun 2100 to work on 19M? I have one of
these, that I am setting up as a firewall between 2 legacy networks, both
of which are 10M, and when I plug that port into the 10M hub, I get
continuing kernel error messages.

I'm considering locking it down, to se if that works, but have not tried
that yet.


AFAIK, phy on that nfe *does not* support 10mbit.



Re: ntp on soekris

2006-06-08 Thread Otto Moerbeek
On Thu, 8 Jun 2006, Pailloncy Jean-Gerard wrote:

Jun  8 09:47:46 r001 ntpd[23319]: adjusting local clock by 0.875716s
Jun  8 09:51:26 r001 ntpd[23319]: adjusting local clock by 0.816038s
  
  Note that the time shown is *not* the time being adjusted,
  but the difference from true time.
  
  I.e at first the offset is 0.87s and later it is only 0.81s so it is
  slowly getting there.
 Ok. Sorry to misunderstand the numbers.

You are misinformed. Time adjustments are fixed in rate. For
adjustments  1s, the rate is +/-40us per 1us. That boils down to
about 1s per 4min. For adjustments larger than 1s, the rate is
+/-400us/1us. 

There are a couple of reasons why you can see alternating
positive/negative adjustments:

1. Your time reference is wobbling.
2. Your clock is wobbling.
3. In some cases ntpd overcompensates. This is especially true for
large adjustments.

I committed a diff to ntpd last week to fix the overcompensating.
Note that this need a recent kernel as well. 

Without extra data you cannot tell what is happening here.

If you see continuous positive or negative adjustments, it just means
you clock is too slow or too fast. Currently, ntpd does not compensate
for such a systematic clock error.

Small adjustments (128ms) are not logged, that's why the log looks
very empty on some systems. This does not mean ntpd does not do
adustments. 

 I do some calculation in spreadsheet.

I think the calculations are based on misunderstanding the way
adjtime(2) works. You also do not take into account that your clock
might be wobbling.

-Otto



Re: double-letter problem in X.org

2006-06-08 Thread Cagdas Tulek

On 6/7/06, Fred Crowson [EMAIL PROTECTED] wrote:

Cagdas Tulek wrote:
 Hi,

 I've installed OpenBSD 3.9 on Toshiba Satellite 1410 laptop,
 yesterday. Everything is fine  except the problem I face on X which
 does not happed at console. When I press a key, it sometimes prints
 double-letters.

 I am asking for help.

 I'm sending the dmesg output as an attachment.

 Thanks...

 Cagdas Tulek

 [demime 1.01d removed an attachment of type application/octet-stream which 
had a name of dmesg.output]

Hi

The following setting in your xorg.conf might help:

Option XkbDisable true



Unfortunately, It didn't change anything. Double-letters still occurs.

Cagdas



Re: ntp on soekris

2006-06-08 Thread Darrin Chandler
On Thu, Jun 08, 2006 at 08:01:16PM +0200, Otto Moerbeek wrote:
 
 There are a couple of reasons why you can see alternating
 positive/negative adjustments:
 
 1. Your time reference is wobbling.
 2. Your clock is wobbling.
 3. In some cases ntpd overcompensates. This is especially true for
 large adjustments.

I have seen a fair amount of all three. My favorite setup these days is
to find a machine that has a decent clock, and will keep time through a
reboot, and config ntpd there to use outside servers. Then I sync my
other boxes to that one. That seems to give the most stable time for all
my machines.

-- 
Darrin Chandler|  Phoenix BSD Users Group
[EMAIL PROTECTED]   |  http://bsd.phoenix.az.us/
http://www.stilyagin.com/  |



Re: ntp on soekris

2006-06-08 Thread Henning Brauer
* Otto Moerbeek [EMAIL PROTECTED] [2006-06-08 20:02]:
 If you see continuous positive or negative adjustments, it just means
 you clock is too slow or too fast. Currently, ntpd does not compensate
 for such a systematic clock error.

this is actually what we lack most in the timekeeping area currently.
I really hope we'll get that solved sometime soon.

-- 
BS Web Services, http://www.bsws.de/
OpenBSD-based Webhosting, Mail Services, Managed Servers, ...
Unix is very simple, but it takes a genius to understand the simplicity.
(Dennis Ritchie)



Re: Problem logging in.

2006-06-08 Thread Bachman Kharazmi

A week ago my open bsd firewall started to show a very strange behaviour.
I have the ssh-daemon running and ususally log-in remotely to be able to
administrate the pf.conf file. But now I cant log in. Ok, maybe I've just
forgott my password. I booted in single user mode and changed it, then
booted normally but couldn't log in anyway. I booted in single user mode
again changed it to another password, changed to another user (using su)
and then changed user to root again (again using su). Was prompted for the
password, entered it and login was again rejected. When i tried to change
the password it complained that something was wrong with a file called
/etc/master.passwd. When looking at the file it contained parts of my
pf.conf file.

If your master.passwd contains parts of your pf.conf things sound really weird.

Remember, if you ever touch master.passwd ALWAYS use vipw to keep dbs synced.

I would try to create a new user foo, check if it works to login as
foo from the localhost using kb. then try with ssh as the new user and
see how that works.

I'm unsure about exactlly what your problem is, your description of
changing passwds really confuse me.

Do not forget to set a existing shell for the user foo.

GL
/bkw



Re: Problem mounting/unmounting a CD

2006-06-08 Thread Otto Moerbeek
On Thu, 8 Jun 2006, Gabriel George POPA wrote:

   Hello BSD users,
 

 /dev/cd0a 93.9M   93.9M  0B   100%/mnt/dvdrw0
 # umount /dev/cd0a
 umount: /mnt/dvdrw0: Input/output error
 # eject /dev/rcd0c
 # # (the tray doesn't move, it's shut)
 # eject -t /dev/rcd0c
 # eject /dev/rcd0c
 # # (the tray still shut remains)
 # # (not CD is in the drive)
 # # (my question is what happens, I cannot mount anymore any CD):
 # # (take a look:)
 # mount /dev/cd0a
 mount: realpath /mnt/dvdrw0: Input/output error
 # mount /dev/cd0a
 mount: realpath /mnt/dvdrw0: Input/output error
 # mount /dev/cd0a
 mount: realpath /mnt/dvdrw0: Input/output error
 # mount /dev/cd0a
 mount: realpath /mnt/dvdrw0: Input/output error
 # (the tray can be ejected and closed but only manually, by pressing the
 buonly manually, by pressing the button)
 

Before you try anything else, you must unmount the device. Try
umount -f /dev/cd0a
 
 Yes, the CD I inserted is good. No, a dmesg for you won't be useful. And, yes,

Home come you know a dmesg isn't useful? A dmesg is almost always useful.

-Otto


 I know you would ask, here is my fstab:


 /dev/wd0a / ffs rw 1 1
 /dev/wd0d /home ffs rw,nodev,nosuid 1 2
 /dev/wd0f /tmp ffs rw,nodev,nosuid 1 2
 /dev/wd0e /usr ffs rw,nodev 1 2
 /dev/wd0g /var ffs rw,nodev,nosuid 1 2
 /dev/fd0a /mnt/floppy0 msdos rw,nodev,nosuid,noauto,noexec 0 0
 /dev/cd0a /mnt/dvdrw0 cd9660 ro,nodev,nosuid,noauto,noexec 0 0
 /dev/cd1a /mnt/cdrw1 cd9660 ro,nodev,nosuid,noauto,noexec 0 0
 
 The optical unit is a DVD+/-RW DL, ASUS (DRW-1608P2, Rev 1.17). Processor
 Intel P4, 3GHz etc. You can imagine the rest...
 I run the standard OpenBSD 3.8 system. I don't think you would ask, but if I
 restart the system it's all OK. It happened to me several
 times; I'm not stupid, I can assure you, but every time I was tired and I
 cannot reproduce the situation;
 My question is: what's going on here?
 All commands were of course executed from the root account.
 
 
   
Thanks
 in advance
 
 
   
   Yours
 in BSDness,
   
   Gabriel
 George POPA



savecore segfaults in June 7 i386 -current snapshot (#870)

2006-06-08 Thread Josh Grosse
I noticed it after just installing it as an upgrade.  I was seeing a 
segmentation fault as /etc/rc was running, and traced it to savecore.

The segmentation fault will drop a core file if I run it manually.  gdb says:

  Core was generated by `savecore'.
  Program terminated with signal 11, Segmentation fault.
  #0  0x1c004a50 in ?? ()
  (gdb)

Obviously, I wonder if this is recreatable by others; that would lead me to
think it might possibly be the snapshot.  

If not, then I know its something local.

Anyone using this snap?

(For completeness, my dmesg follows)

OpenBSD 3.9-current (GENERIC) #870: Wed Jun  7 17:11:37 MDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Sempron(tm) 2600+ (AuthenticAMD 686-class, 256KB L2 cache) 1.84 GHz
cpu0: 
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem  = 502820864 (491036K)
avail mem = 451043328 (440472K)
using 4256 buffers containing 25243648 bytes (24652K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(37) BIOS, date 01/07/05, BIOS32 rev. 0 @ 0xfb9b0, 
SMBIOS rev. 2.2 @ 0xf (44 entries)
bios0: ASUS A7VT
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf/0xda84
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfda10/112 (5 entries)
pcibios0: PCI Exclusive IRQs: 3 5 10 11
pcibios0: PCI Interrupt Router at 000:17:0 (VIA VT82C596A ISA rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc/0x7e00 0xc8000/0x8000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 VIA VT8378 PCI rev 0x00
ppb0 at pci0 dev 1 function 0 VIA VT8377 AGP rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 VIA VT8378 VGA rev 0x01: aperture at 
0xe400, size 0x1000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
dc0 at pci0 dev 8 function 0 Lite-On PNIC-II rev 0x25: irq 10, address 
00:a0:cc:e3:42:d6
dcphy0 at dc0 phy 31: internal PHY
uhci0 at pci0 dev 16 function 0 VIA VT83C572 USB rev 0x80: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 16 function 1 VIA VT83C572 USB rev 0x80: irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 16 function 2 VIA VT83C572 USB rev 0x80: irq 5
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 16 function 3 VIA VT6202 USB rev 0x82: irq 3
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: VIA EHCI root hub, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
viapm0 at pci0 dev 17 function 0 VIA VT8235 ISA rev 0x00
iic0 at viapm0
pciide0 at pci0 dev 17 function 1 VIA VT82C571 IDE rev 0x06: ATA133, channel 
0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: ExcelStor Technology J880
wd0: 16-sector PIO, LBA48, 78533MB, 160836480 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: LITE-ON, DVDRW SHW-160P6S, PS01 SCSI0 5/cdrom 
removable
wd1 at pciide0 channel 1 drive 1: Maxtor 92732U8
wd1: 16-sector PIO, LBA, 26059MB, 53369568 sectors
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4
wd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 4
auvia0 at pci0 dev 17 function 5 VIA VT8233 AC97 rev 0x50: irq 5
ac97: codec id 0x41445368 (Analog Devices AD1888)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auvia0
vr0 at pci0 dev 18 function 0 VIA RhineII-2 rev 0x74: irq 11, address 
00:11:2f:85:b1:90
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 10: OUI 
0x004063, model 0x0032
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83697HF
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ff6d netmask ff6d ttymask ffef
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: vendor 0x062a product 0x, rev 1.10/0.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302



Re: ip address ?

2006-06-08 Thread Nick Guenther

On 6/8/06, akonsu [EMAIL PROTECTED] wrote:

hello,

my openbsd machine is conected to a windows machine. the windows machine has
a wireless connection and gets its ip using dhcp. the openbsd machine gets
its ip from the windows machine also by using dhcp on boot.

the windows machine runs cygwin X server and the openbsd machine uses its
display when running various x applications.

so i need to set up DISPLAY variable on openbsd to point to this screen.

is there a way to automatically retrieve the ip address of the windows
machine and set up DISPLAY variable in the login script on openbsd machine?
also, how to handle ip renewals?


So, are you saying the windows machine is the gateway for the OpenBSD
machine? If that's the case, then you can just screen-scrape `route
show` (there's probably a better way than screen-scraping tho). If
that's not the case, then perhaps you can scrape the boot logs (I
believe dhclient says something like 'bound to X.X.X.X from Y.Y.Y.Y').
Be aware though, that in either of these set ups you must trust that
the dhcp server is actually your trusted windows box.

-Nick



squid and pf and dansguardian

2006-06-08 Thread Allen Theobald
Greetings,

I get transparent proxying with squid and pf.  

I get dansguardian and pf.

What I don't get is squid, dansguardian, and pf.

pf.conf fragment:

   int_if=gem0
   ext_if=kue0

   # redirect to squid
   rdr on $int_if inet proto tcp from any to any \
   port www - 127.0.0.1 port 3128

   ## Allow the redirected connections to pass.
   pass in on $int_if inet proto tcp from any to 127.0.0.1 \
   port 3128 keep state

   ## Also, the proxy must be able to establish outgoing
## connections to external web servers.
   pass out on $ext_if inet proto tcp from any to any \
   port www keep state

   pass quick on $int_if

But now I want to put dansguardian on.  It listens on 8080, uses 
proxy port 3128.

How do these rules change?  I think I change 3128 to 8080 in the 
above rules.  But what happens to 3128?  Do I still need a 'pass in'
rule for 3128?

Thanks and take care,

Allen
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 



Re: Which free board software for PostgeSQL?

2006-06-08 Thread Joachim Schipper
On Wed, Jun 07, 2006 at 08:46:56PM +0200, Michael Lechtermann wrote:
 Hi,
 
 anyone can recommend a free PHP board/forums software for use with
 PostgreSQL 8.x?
 
 PgSQL isn't mentioned in the vBulletin homepage.
 PHPBB is supposed to work with 7.x, not sure about 8.x

I use PHPBB with PostgreSQL 8.0, so it should work - 8.1 has changed
nothing which I could imagine breaking PHPBB, or much of anything for
that matter (except for newly introduced bugs, of course, but the
PostgreSQL teams doesn't seem to do too bad on that front).

However, as mentioned before, PHPBB isn't exactly secure. In fact, it
pretty much has its own box on my network...

Joachim



Re: ip address ?

2006-06-08 Thread Joachim Schipper
On Wed, Jun 07, 2006 at 10:42:41PM -0700, akonsu wrote:
 hello,
 
 my openbsd machine is conected to a windows machine. the windows machine has
 a wireless connection and gets its ip using dhcp. the openbsd machine gets
 its ip from the windows machine also by using dhcp on boot.
 
 the windows machine runs cygwin X server and the openbsd machine uses its
 display when running various x applications.
 
 so i need to set up DISPLAY variable on openbsd to point to this screen.
 
 is there a way to automatically retrieve the ip address of the windows
 machine and set up DISPLAY variable in the login script on openbsd machine?
 also, how to handle ip renewals?

I'm afraid neither is possible. However, I'm not sure about the proposed
architecture, but if the Windows machine has at least one interface with
a fixed IP address, that might be helpful.

For a very dirty solution, abuse nmap, and include some actual
authentication - whatever you're tunneling X over should do. (Oh, you
are aware that running X over an unencrypted link is a VERY bad idea,
right? Not saying you're doing so, but if you are...)

Some alternatives exist; I'm not sure if a service like DynDNS.org
accepts internal IP addresses (192.168.0.0/16 and the equivalent B and A
classes), but that would solve some part of what you're trying to do.
There are various, mostly not very robust, ways to do something similar
on one's own.

Joachim



Re: Combining boot floppies

2006-06-08 Thread Joachim Schipper
On Wed, Jun 07, 2006 at 11:36:14PM -0700, Darrin Chandler wrote:
 On Thu, Jun 08, 2006 at 01:08:04AM -0500, Michael White wrote:
  Hi all,
  
  I'm attempting my first install of OpenBSD (version 3.9) on an HP Omnibook 
  800CT (Pentium 166, 80 MB RAM, 4.3 GB HD, 3COM 3CXEM556 Carbus Ethernet 
  card), coming over from RH9.0.  One peculiarity of the 800CTs is that the 
  SCSI CDROM is not bootable, so I'm down to booting with floppies.
  
  I first attempted to boot from floppyC39.fs, since that's supposed to be 
  the 
  image for laptops.  Well, it does recognize my Ethernet card, but seems to 
  choke on the hard drive.  After recognizing the Ethernet card, I see the 
  following:
  
  --
  wd0(wdc0:0:0): timeout
  type: ata
  c_bcount: 512
  c_skip: 0
  wd0(wdc0:0:0): timeout
  type: ata
  c_bcount: 512
  c_skip: 0
  WARNING: preposterous time in file system
  WARNING: file system time much less than clock time
  --
  
  After that, the machine is locked up.  So I boot from floppy39.fs 
  instead.  
  That had no problem with the hard drive.  I was able to successfully 
  partition the drive.  But that image does not recognize my Ethernet card, 
  so 
  I'm unable to retrieve any images (didn't see an option for PPP).
  
  Even after formatting the hard drive under the floppy39.s floppy, the 
  floppyC39.fs floppy chokes on the hard drive.
  
  Is there any way to combine the two capabilities?  I.e. dropping to the 
  shell, 
 
 Do you know if either or both of those recognize your CD? If so, you can
 download the install sets and burn them on CD, and do your install from
 there w/out ethernet. If you've got access to a burner that's probably
 the simpler way to go. Or try out the Xircom and see if it works.

Be aware, though, that (not all|many) older CD drives do not recognize
(all|most|some|any) burned CDs.

Joachim



Re: ip address ?

2006-06-08 Thread Stuart Henderson
On 2006/06/08 22:16, Joachim Schipper wrote:
  is there a way to automatically retrieve the ip address of the windows
  machine and set up DISPLAY variable in the login script on openbsd machine?
  also, how to handle ip renewals?

If this is for programs started from an ssh session to the
OpenBSD box from the windows box, just use X forwarding.



Re: ip address ?

2006-06-08 Thread Chris 'Xenon' Hanson

Joachim Schipper wrote:

my openbsd machine is conected to a windows machine. the windows machine has
a wireless connection and gets its ip using dhcp. the openbsd machine gets
its ip from the windows machine also by using dhcp on boot.

is there a way to automatically retrieve the ip address of the windows
machine and set up DISPLAY variable in the login script on openbsd machine?
also, how to handle ip renewals?


  I wonder if you could misuse traceroute to do this somehow? Traceroute to a known 
outside host that you know will have to traverse the Windows gateway, with a low 
max-hops value, and then parse the output of traceroute to see what the n'th hop was.


--
 Chris 'Xenon' Hanson | Xenon @ 3D Nature | http://www.3DNature.com/
 I set the wheels in motion, turn up all the machines, activate the programs,
  and run behind the scenes. I set the clouds in motion, turn up light and 
sound,
  activate the window, and watch the world go 'round. -Prime Mover, Rush.



Re: Problem logging in.

2006-06-08 Thread Joachim Schipper
On Thu, Jun 08, 2006 at 02:22:19PM +0200, Jonas Lindskog wrote:
 Hello,
 
 A week ago my open bsd firewall started to show a very strange behaviour.
 I have the ssh-daemon running and ususally log-in remotely to be able to
 administrate the pf.conf file. But now I cant log in. Ok, maybe I've just
 forgott my password. I booted in single user mode and changed it, then
 booted normally but couldn't log in anyway. I booted in single user mode
 again changed it to another password, changed to another user (using su)
 and then changed user to root again (again using su). Was prompted for the
 password, entered it and login was again rejected. When i tried to change
 the password it complained that something was wrong with a file called
 /etc/master.passwd. When looking at the file it contained parts of my
 pf.conf file.
 
 Have I've been hacked or is it just a major error done from my side.

Most likely, some form of major error. Might be filesystem damage; could
you have done something to cause that?

If master.passwd is unparseable, all sorts of nasty stuff happens.
Restore from a 3*etc.tgz file, or - if possible - from backups.

(Just a generic pointer - most hackers know what they are doing, and are
quite careful not to make too much user-visible changes to the system;
something as blatantly obvious as this is unlikely to be the work of a
hacker. Even bad hackers are unlikely to randomly trash important
files.)

Joachim



Re: SMP

2006-06-08 Thread Joachim Schipper
On Thu, Jun 08, 2006 at 08:34:28AM -0300, Gustavo Rios wrote:
 Dear friends,
 
 i have been having an increasing interest on OpenBSD internals. So, my
 first movement was to buy some Unix books on OS design like The Design
 of the 4.4BSD  .
 
 One thing i would like to know better is about SMP. Up to now i could
 not figure it out about the algorithm choice and motivation, not i can
 have a good ideia about how openbsd does behave on an SMP system
 compared other unices like Solaris/AIX, etc or even pretenders like
 Linux.
 
 Thank you a lot for your time and cooperation.

Unless I am sorely mistaken, OpenBSD uses the old - and slow - Big
Kernel Lock technique. This has the disadvantage that the kernel quickly
becomes a bottleneck; and for some applications, notably firewalling,
having more than one processor isn't likely to do any good (bsd.mp has
different interrupt handling though, and this seems to sometimes work
better than bsd's strategy; this is a different issue though, and I
don't know enough about it to say anything more sensible).

So, OpenBSD's SMP support isn't very good, performance-wise. On the
other hand, simple architectures have their own advantages: very few, if
any, bugs (compare to Linux, for instance!); no security problems; small
time requirements, so other parts can be improved; and it's easy to code
correctly.

I don't know about AIX, but Linux will be faster; FreeBSD will most
likely be faster, as well; and Solaris is quite possibly the best system
to be running on a 'very symmetric' system with lots of processors
and/or cores. At least performance-wise.

Joachim



which package to install?

2006-06-08 Thread Gustavo Rios

Hey folks,

i would like to install python in my 3.8 box, but when i cd'ed to
/usr/ports/lang/python, i saw two directories, once for 2.3 another
for 2.4. I would like to install on 2.4, but not both. I could not
figure it out how to install only 2.4 the official way, since a
make install the that directory would end up installing them both.

Thanks a lot for your time and cooperation.

Best regards.



like the faq 14.16.1, partition is not in my disklabel ... need help anyway

2006-06-08 Thread Didier Wiroth
Hello,
My ntfs amd comaq diag. partition is not in the disklabel.
Unfortunately I don't know how to add correctly in the disklabel.
I've read the faq 14.16.1 but it only shows a modification.

Here is my fdisk output, which shows id 0 the ntfs partition:

Disk: wd0   geometry: 12921/240/63 [195365520 Sectors]
Offset: 0   Signature: 0xAA55
 Starting   Ending   LBA Info:
 #: idC   H  S -C   H  S [   start:  size   ]

*0: 070   1  1 - 6800 239 63 [  63:   102831057 ] HPFS/QNX/AUX
 1: 12 12270   0  1 - 12920 239 63 [   185522400: 9843120 ] Compaq Diag.
 2: A6 6801   0  1 - 12269 239 63 [   102831120:82691280 ] OpenBSD
 3: 000   0  0 -0   0  0 [   0:   0 ] unused

Here is current my disklabel:
16 partitions:
# sizeoffset  fstype [fsize bsize  cpg]
  a:   2097648 102831120  4.2BSD   2048 16384  328 # Cyl 102015 -104095
  b:   1024128 104928768swap   # Cyl 104096 -105111
  c: 195371568 0  unused  0 0  # Cyl 0 -193820
  d:   4194288 105952896  4.2BSD   2048 16384  328 # Cyl 105112 -109272
  e:   1024128 110147184  4.2BSD   2048 16384  328 # Cyl 109273 -110288
  f:   4194288 71312  4.2BSD   2048 16384  328 # Cyl 110289 -114449
  g:  10486224 115365600  4.2BSD   2048 16384  328 # Cyl 114450 -124852
  h:   4194288 125851824  4.2BSD   2048 16384  328 # Cyl 124853 -129013
  i:   2097648 130046112  4.2BSD   2048 16384  328 # Cyl 129014 -131094
  j:   3072384 132143760  4.2BSD   2048 16384  328 # Cyl 131095 -134142
  k:  50306256 135216144  4.2BSD   2048 16384  328 # Cyl 134143 -184049


What do I have to add to disklabel to be able to access the ntfs and the compaq 
diag partition?

For ntfs something like:
l: 102831057 63 unknown # Cyl ???

I would really appreciate some help.

Thank you very much !

Kind regards
Didier



Re: Linphone installation

2006-06-08 Thread Nikolaus Hiebaum
* Nikolaus Hiebaum wrote on Jun 8, 2006 [22:43, +0200] :

 My approach was to download the source and compile it myself. However, I am
 running into this error as I run ./configure 
 --with-osip=/usr/local/include/osip2

I forgot to write that I am trying to install linphone-1.3.5.


-- 
Beste Gr|_e / Best regards ,
Nikolaus Hiebaum



Linphone installation

2006-06-08 Thread Nikolaus Hiebaum
Hello,

I was looking for a SIP softphone working under OpenBSD and from I found it
sounded as if Linphone would work. There is an unofficial port for it (cf.
http://marc.theaimsgroup.com/?l=openbsd-portsm=113297483831524w=2) of an
older version which doesn't build, however.

My approach was to download the source and compile it myself. However, I am
running into this error as I run ./configure 
--with-osip=/usr/local/include/osip2

checking for osip2/osip.h... no
configure: error: Could not find osip2 headers !

I have osip2 here /usr/local/include/osip2 and have the libosip2-2.2.0p0
installed. Since I couldn't find any pointer what to do now, I came here to ask
you, please, to get me jump started how to fix this.

If you know of another SIP softphone working under OpenBSD, I am open to
suggestions.

-- 
Beste Gr|_e / Best regards ,
Nikolaus Hiebaum



Re: savecore segfaults in June 7 i386 -current snapshot (#870)

2006-06-08 Thread Josh Grosse
On Thu, Jun 08, 2006 at 02:32:39PM -0400, Josh Grosse wrote:
 I noticed it after just installing it as an upgrade.  I was seeing a 
 segmentation fault as /etc/rc was running, and traced it to savecore

In response to my own post, Ray Lai very politely asked me to rebuild
savecore with symbols, and run a back trace, to make the gdb output
useful.  Sometimes, we end-users don't add one to one and arrive at two.

I have now done what I should have done before posting:  

Core was generated by `savecore'.
Program terminated with signal 11, Segmentation fault.
#0  0x1c004a50 in _kvm_kvatop (kd=0x80434000, va=3496836692, pa=0xcf7c3030)
at /usr/src/lib/libkvm/kvm_i386.c:186
186 if ((PDE(vm, va)  PG_V) == 0)
(gdb) bt
#0  0x1c004a50 in _kvm_kvatop (kd=0x80434000, va=3496836692, pa=0xcf7c3030)
at /usr/src/lib/libkvm/kvm_i386.c:186
#1  0x1c0045fa in kvm_read (kd=0x80434000, kva=3496836692, buf=0xcf7c3064,
len=4) at /usr/src/lib/libkvm/kvm.c:865
#2  0x1c000be0 in dump_exists ()
#3  0x1c000488 in main ()
(gdb)



Yes, MySQL sucks (was: Re: Lockups and Semop panics)

2006-06-08 Thread Joachim Schipper
On Thu, Jun 08, 2006 at 10:19:31AM -0600, Bob Beck wrote:
 * Otto Moerbeek [EMAIL PROTECTED] [2006-06-08 10:00]:
  On Thu, 8 Jun 2006, Michael Erdely wrote:
  
   Hi,
   
   I've got a Dell Dimension XPS B866r desktop running as my web/mail
   server (recently upgraded to 3.9).
   
   Occasionally, after a seemingly random amount of time, the machine
   will do one of two things: it will either lockup/freeze where
   there are no messages on the console, but you cannot type, ping or
   access the box in any way (but the reset button) OR, since I have
   ddb.panic=0, it will reboot with the following message from my
   serial console:

  your system is running out of semaphore undo data structures. Try
  increasing at least kern.seminfo.semmnu. Other semaphore related
  sysctl's might need an increase as well.

   And mysqueal sucks...
 
   Your system may run out of other things as well given the bloatware
 you're running on it.  anything else I have mysqeal on and any
 significant amount of users I usually have to crank up quite a few of
 the default limits, both in the kernel and in mysql - I usually build
 a GENERIC with maxusers=128 to start, and then find the 80 bazillion
 knobs in mysqeal to turn to tell it to use file descriptors. no really
 use more than 100 file descriptors.  no really really use more than 
 100 file descriptors
 
   If you have a small number of users you may be fine. however
 seeing what you have there and 512 mb of ram, you may want a bit more
 if you have significant usage.
 
   Did I mention that mysqueal sucks?

To be fully honest, OpenBSD sucks quite a bit too, in this area
(massively threaded servers). There are good reasons for this suckage;
but MySQL does not perform quite as well on OpenBSD as it does on almost
every other system, so it's not entirely fair to only base one's opinion
on that.

Of course, I installed it first on Linux, and then found that it was
basically a fastish table (not a RDBMS - use PostgreSQL if you want
that). With a lot of crud. And, indeed, quite strange configuration
options. And which required one to install something like 3.x to build
the client part of 4.x, or something similarly inane (supposedly,
everyone used binary packages). And which has had quite a few security
problems of its own.

Finally, it's the wrong solution in almost every case. It's not a
database - again, use PostgreSQL. If you only want a table, you could
look at SQLite - I never used it, but it's supposedly much, much easier
and very fast. Of course, it's even less of an RDBMS than MySQL, but it
still works for PHP scripts and it's not like MySQL is much good for
anything else.
Never mind that PHP scripts are, themselves, better replaced by a proper
solution - like FastCGI - written in a proper language - i.e., almost
anything but PHP: Perl, Python, Ruby[2], C[1].

Joachim

[1] Some of these, especially C, would cost slightly more time, though,
which is an issue in some cases. However, I'd assert that anyone not
capable of writing in a real language shouldn't be writing
internet-exposed programs in the first place.
Additionally, I'm not allowed to do this. A good idea, probably - a
random PHP script can be understood fairly easily and just plonked down
on any commercial hoster; on the other hand, a heavily optimized C
program is less likely to be understood...
[2] It's been said that Ruby is very slow. I don't know anything about
it, really - if this is the case, its place in the list of real
languages might need reconsidering.



Re: which package to install?

2006-06-08 Thread viq

On 6/8/06, Gustavo Rios [EMAIL PROTECTED] wrote:

Hey folks,

i would like to install python in my 3.8 box, but when i cd'ed to
/usr/ports/lang/python, i saw two directories, once for 2.3 another
for 2.4. I would like to install on 2.4, but not both. I could not
figure it out how to install only 2.4 the official way, since a
make install the that directory would end up installing them both.

Thanks a lot for your time and cooperation.

Best regards.


cd /usr/ports/lang/python/2.4  make install clean-depends

--
viq



Re: popular mail squid virus scanning technique for openbsd

2006-06-08 Thread Craig Skinner
On Mon, Jun 05, 2006 at 12:33:23PM +0530, Siju George wrote:
 Hi,
 
 One of my openBSD server is the Gateway/Firewall to internet.
 Our mal server(s) is on the Internet.
 
 What would be the best method to scan all mail traffic through the firewall?
 Currenly I am using plain NAT.
 
 It would be great if people can recommend which is the best software
 from packages/ports if I have to install any.
 

I successfully use spamd in grey listing mode, with postfix, and that's
all. Works great. Use extensive postfix dns checks and that kills all
non-mailling list spam:

smtpd_recipient_restrictions =
 reject_non_fqdn_hostname
 reject_invalid_hostname
 reject_non_fqdn_sender
 reject_non_fqdn_recipient
 reject_unknown_client
 reject_unknown_hostname
 reject_unknown_sender_domain
 reject_unknown_recipient_domain
 permit_mynetworks
 reject_unauth_destination
 check_recipient_access pcre:$config_directory/recipient_checks.pcre
 check_client_access btree:$config_directory/client_checks.map
 check_sender_access btree:$config_directory/sender_checks.map
 check_client_access pcre:$config_directory/client_checks.pcre
 check_helo_access btree:$config_directory/helo_checks.map
 check_helo_access pcre:$config_directory/helo_checks.pcre


smtp_skip_5xx_greeting = no
smtp_skip_4xx_greeting = no
smtpd_helo_required = yes
smtpd_recipient_limit = 50
smtpd_recipient_overshoot_limit = 5
smtpd_reject_unlisted_sender = yes
smtpd_soft_error_limit = 3
smtpd_hard_error_limit = 6
biff = no
delay_warning_time = 1d
message_size_limit = 5242880
disable_vrfy_command = yes
unknown_address_reject_code = 554
unknown_hostname_reject_code = 554
unknown_client_reject_code = 554
strict_rfc821_envelopes = yes
strict_mime_encoding_domain = yes
strict_8bitmime = yes
default_database_type = btree
header_size_limit = 5120
body_checks = pcre:$config_directory/body_checks.pcre
header_checks = pcre:$config_directory/header_checks.pcre
allow_percent_hack = no

This lot is pretty heavy to the point that it does reject more legit
mail than most people would tolerate, but hey, tough. The postfix docs
and mailling list are really good.

-- 
Craig Skinner | http://www.kepax.co.uk | [EMAIL PROTECTED]



Re: which package to install?

2006-06-08 Thread Bryan Irvine

Go into the 2.4 dir and make install.

--Bryan

On 6/8/06, Gustavo Rios [EMAIL PROTECTED] wrote:

Hey folks,

i would like to install python in my 3.8 box, but when i cd'ed to
/usr/ports/lang/python, i saw two directories, once for 2.3 another
for 2.4. I would like to install on 2.4, but not both. I could not
figure it out how to install only 2.4 the official way, since a
make install the that directory would end up installing them both.

Thanks a lot for your time and cooperation.

Best regards.




Re: ip address ?

2006-06-08 Thread Dan Farrell
 -Original Message-
 From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf
Of
 Chris 'Xenon' Hanson
 Sent: Thursday, June 08, 2006 4:28 PM
 To: misc
 Subject: Re: ip address ?
 
 Joachim Schipper wrote:
  my openbsd machine is conected to a windows machine. the windows
 machine has
  a wireless connection and gets its ip using dhcp. the openbsd
machine
 gets
  its ip from the windows machine also by using dhcp on boot.
 
  is there a way to automatically retrieve the ip address of the
windows
  machine and set up DISPLAY variable in the login script on openbsd
 machine?
  also, how to handle ip renewals?
 
I wonder if you could misuse traceroute to do this somehow?
Traceroute
 to a known
 outside host that you know will have to traverse the Windows
gateway,
 with a low
 max-hops value, and then parse the output of traceroute to see what
the
 n'th hop was.
 
 --
   Chris 'Xenon' Hanson | Xenon @ 3D Nature |
http://www.3DNature.com/
   I set the wheels in motion, turn up all the machines, activate the
 programs,
and run behind the scenes. I set the clouds in motion, turn up
light
 and sound,
activate the window, and watch the world go 'round. -Prime Mover,
 Rush.


Or a twist I use when connecting locally to machines whose IP address I
don't know-- assign a dummy address to the MAC (which never changes)
then connect to that address.

Not sure how practical a solution that would be for you, but then
perhaps connecting to the FQDN of the windows box, as opposed to the IP
address, and let DNS figure out what that address is... maybe that would
work? Or am I missing something?

Dan Farrell
Applied Innovations
[EMAIL PROTECTED]



[4.0 release] PR event

2006-06-08 Thread Craig Skinner
Hiya list,

If you are like me, you are probably pondering how the milestone OpenBSD
4.0 release should be launched in the public eye.

Due to the extraordinary volume of additional software that any point0
release brings to our valued customer base, I thought it high time to
elect a specialist Chief Liaison Officer - Temporary, CLOT.

Or, if as I suspect, that a global enterprise such as ours, would
require a permanent spokesperson: Pubic Relations Articulation
Technologist, PRAT.

Now, I understand that the person specification for such a demanding
role is very difficult to precisely define, but through supportive
teamwork via conference calls, that this vision can be realised.

The most important new software to be launched is the much exalted
tFace. I'm sure there is no need to expand on the top secret, *and*
first to market operational Telepathic Interface. (Search the hidden
archives at http://i-no-thinky.so) The CLOT/PRAT must evangelise the
first deliverable protocol: tMail, and emphasise the pain point
reduction for enterprise customers. He/she must also be able to downplay
the unfortunate incident when the FBI's crack agent Moldiberg
intercepted Wacko Jacko's next lover requirements transmission.

I have an outline of the 4.0 launch event and thought we could make
pivotal use of a 40 theme: 40 scantily clad dancing girls. Each one of
which shall be 40 years old and weigh some 40 stone (254kgs,  if you
don't use the British Imperial measuring system). 

We could hire a quality band to perform the classic song Life begins at
40. I thought the Spice Girls would dovetail quite well as each member
has 40 men a year, I suspect due to their musical talents. - Theo may
want to comment here.

The Windows Vista Migratory Team may want to rent a bouncy castle for
their target demographic. I am confident we can get all the
environmentally friendly 40x40 girls on the castle in time with the
music.

I know what you are thinking, and I've had a risk analysis report
commissioned on the resultant pulsating solar eclipse. I have assurances
from the highest zoological consultants that the homosexual activities
of the rare Tibetan Lama will return to acceptable levels in due course.
Of more interest is that the resulting press coverage is sure to
guarantee market dominance through many licence sales.

To ensure the production is harmoniously co-ordinated amoungst
stakeholders, we may need the services of a Team Heading Uber Geek,
THUG.

To effect the initial screening of volunteer CLOTs, PRATs and THUGs,
please ensure any replies are on list and on topic. Remember to keep
the noise down on this one as we need to focus on the long term
financial success of our company.

-- 
Craig Skinner | http://www.kepax.co.uk | [EMAIL PROTECTED]



Re: Linphone installation

2006-06-08 Thread Stuart Henderson
On 2006/06/08 22:43, Nikolaus Hiebaum wrote:
 My approach was to download the source and compile it myself. However, I am
 running into this error as I run ./configure 
 --with-osip=/usr/local/include/osip2

I've just been trying to get a softphone running too. You'll
get a bit further using --with-osip=/usr/local/include but I haven't
got the build to complete yet.

 If you know of another SIP softphone working under OpenBSD, I am open to
 suggestions.

Me too! I thought minisip looked the most interesting,
but it looks like a right pig to build here.



Re: Toshiba Tecra 8000 xorg.conf

2006-06-08 Thread Paul de Weerd
On Thu, Jun 08, 2006 at 08:04:43PM +1200, Joshua Sandbrook wrote:
| Yeah I saw that. But xorg does not just 'work by default' at 1024x768 for
me.
| It just runs at 800x600 and it seems thats all it can be bothered doing
right
| now...

Ah ok, so that's what being grumpy means ;)


You could try configuring X, saving a config file and editing that to
give you 1024x768. If that doesn't get you any further, could you post
your Xorg.0.log (maybe put it online somewhere) ?

For future reference, please indicate what you've done to try to solve
the problem before posting so you don't get referred to stuff you've
tried already. Adding a dmesg (which you did, yaay ;) and (in case of
X problems) X log files usually helps too.

being grumpy doesn't indicate that X works perfectly at 800x600
where you'd want it to run at another resolution (at least, not to me
.. but maybe I'm just being obnoxious).

Cheers,

Paul 'WEiRD' de Weerd

| On Thursday 08 June 2006 19:59, you wrote:
|  Hi Joshua,
| 
|  On Thu, Jun 08, 2006 at 07:39:15PM +1200, Joshua Sandbrook wrote:
|  | Anyone out there running 3.9 on a Toshiba Tecra 8000 ? Im trying to get
|  | it to run at 1024x768 but its being grumpy.
| 
|  Check http://www.openbsd.org/i386-laptop.html - the machine is listed
|  there with several tips on how to get it working. Xorg did not require
|  any config for me (Just Works (tm)).
| 
|  Cheers,
| 
|  Paul 'WEiRD' de Weerd

--
[++-]+++.+++[---].+++[+
+++-].++[-]+.--.[-]
 http://www.weirdnet.nl/

[demime 1.01d removed an attachment of type application/pgp-signature]



Re: Linphone installation

2006-06-08 Thread Craig Skinner
On Thu, Jun 08, 2006 at 10:43:55PM +0200, Nikolaus Hiebaum wrote:
 
 If you know of another SIP softphone working under OpenBSD, I am open to
 suggestions.

This is the only VoIP phone that I have found to work well:

http://www.shop.bt.com/invt/caw126

I used to work for an ISP that had its own VoIP system. We spent more
time appologising to customers about poor call quality and dropped
lines, not to mention trying to get new customers to replace the pissed
off ones. Fine as a toy for home use.


-- 
Craig Skinner | http://www.kepax.co.uk | [EMAIL PROTECTED]



Re: ip address ?

2006-06-08 Thread akonsu
thanks all for help.

i can change my whole setup. what i have now is the best that i could think
of. basically the problem is that my laptop's wireless card is not supported
yet and i run a VMWare virtual machine under my windows and openbsd runs
from a physical disk partition on this virtual machine. so openbsd connects
to windows through these virtual ethernet connections installed with the
VMWare player. this way openbsd can use internet.

but since VM window is too small, i want to run openbsd applications on
windows desktop, so i am using cygwin X.

this response suggests that i can use ssh to connect to openbsd. could you
give me more pointers? is there a better setup that i can use?

what a mess it is with all these mutiple OS running on the same machine...
;-)

konstantin


2006/6/8, Stuart Henderson [EMAIL PROTECTED]:

 On 2006/06/08 22:16, Joachim Schipper wrote:
   is there a way to automatically retrieve the ip address of the windows
   machine and set up DISPLAY variable in the login script on openbsd
 machine?
   also, how to handle ip renewals?

 If this is for programs started from an ssh session to the
 OpenBSD box from the windows box, just use X forwarding.



Re: Yes, MySQL sucks (was: Re: Lockups and Semop panics)

2006-06-08 Thread Craig Skinner
On Thu, Jun 08, 2006 at 10:54:01PM +0200, Joachim Schipper wrote:
  Did I mention that mysqueal sucks?
 
 Finally, it's the wrong solution in almost every case. It's not a
 database - again, use PostgreSQL.

Seconded. MySQL is only an SQLish interface to a file system, it is not
a database. Fine for keeping random banner ads in, but that is it.

-- 
Craig Skinner | http://www.kepax.co.uk | [EMAIL PROTECTED]



Re: OpenOffice.org 2.0 works on OpenBSD

2006-06-08 Thread Tobias Ulmer
On Thu, Jun 08, 2006 at 10:21:02AM +0200, Nikolaus Hiebaum wrote:
 On June 6, 2006 00:44, Tobias Ulmer wrote:
 
  Search the ports@ mailing list, there's a port for it.
 
 Thanks for the tip and also for the link with instructions. Yes, I was
 able to underatand it.  :-) The title of the site chruetertee.ch,
 however, took me some more time. :-
 
 I found something
 http://marc.theaimsgroup.com/?l=openbsd-portsm=114289306831495w=2 on
 ports. ;-) I assume the proper way then would be to download this
 tgz-file, put it in /ports, and then build it the usual way?

Yes, its a normal port, but it could use an update...

---

Some thoughts about your sudo problem. Maybe you have java in your PATH
and sudo changes something in the environment. If java is in your PATH,
oo will not work!

Tobias

 
 -- 
 Beste Gr|_e / Best regards,
 Nikolaus Hiebaum



Re: new port: OpenBSD/aviion

2006-06-08 Thread Dries Schellekens

Miod Vallat wrote:


I would like to extend the hardware coverage of this port by
supporting more models and more on-board devices. But as long as I do
not have AViiON hardware and rely on other people for testing,
development will not progress very fast, and will hit on our nerves.
So if you have an unused AViiON machine in your Attic you have no real
use for, or if you know someone who wants to get rid of his... please
get in touch with me. This would definitely help this emerging port a
lot!


I saw just this:
http://cgi.ebay.com/Data-General-system-board-for-Aviion-5500-005-039600_W0QQitemZ6888270148QQihZ013QQcategoryZ1244QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

Would it help if someone bought that board for you? Preferrably someone 
living in the USA...



Cheers,

Dries



Re: ip address ?

2006-06-08 Thread Stuart Henderson
On 2006/06/08 14:35, akonsu wrote:
 i can change my whole setup. what i have now is the best that i could think
 of. basically the problem is that my laptop's wireless card is not supported
 yet

If it's minipci, it's usually cheap and not difficult to swap it for
a ralink-based card (but check you don't have anything silly to do first,
like run tpwireless on an IBM). Or you probably have the option of using
plug-in wireless (USB/PC-card), which might be slightly annoying, but is
probably less annoying than having to run Windows like this...

 but since VM window is too small, i want to run openbsd applications on
 windows desktop, so i am using cygwin X.
 
 this response suggests that i can use ssh to connect to openbsd. could you

Yes, you can still ssh to something running on the same physical box...

 give me more pointers? is there a better setup that i can use?

For console apps just run sshd on the OpenBSD vm and connect to it with
PuTTY (or OpenSSH compiled under Cygwin, but then you have crappy Windows
terminal emulation to put up with, which I mostly try and avoid - if I'm
running some cygwin/windows box I usually putty to localhost for CLI).

If you have GUI apps to run too, turn on X11 forwarding (in the GUI for
PuTTY, or in ~/.ssh/config for OpenSSH) and it will send it over a tunnel
in the SSH session and set DISPLAY for you, so you type 'xterm' in the
session and it appears on your local screen.

Of course by connecting from Windows to OpenBSD, you are reliant on
Windows for security of those sessions...



Re: ip address ?

2006-06-08 Thread Raja Subramanian

On 6/9/06, akonsu [EMAIL PROTECTED] wrote:

i run a VMWare virtual machine under my windows and openbsd runs
from a physical disk partition on this virtual machine. so openbsd connects
to windows through these virtual ethernet connections installed with the
VMWare player. this way openbsd can use internet.


I use NAT networking with VMPlayer and this makes my Windows host
with multiple *bsd guests very simple to setup.  Using NAT for VMWare
networking creates a 192.168.214.0/24 network with the following features:

Windows host machine: 192.168.214.1
Gateway: 192.168.214.2
DNS: 192.168.214.2

Virtual Machines:  192.168.214.3-254 (I use static IPs)

I don't bother with DHCP on the VMs and use static IPs (and save them
in PuTTY sessions).  The VMs have no problems accessing the web
over any wired or wireless network on the host.

I do not use any services on my host machine from the VMs, but I'm
certain setting DISPLAY=192.168.214.1:0 should allow you to run X
apps.

- Raja



setting ath txpower via ifconfig errors out

2006-06-08 Thread Antonios Anastasiadis

Trying to change txpower on atheros wireless cards does not set the
power accordingly, just errors out.
I submitted this mail to bugs@ but I cannot find it in the bug
tracking system page, so I send it here also in case there was a
problem.
I don't have the skills to figure out anything by looking at the
source code. Perhaps manipulation with txpower isn't supported at all
in ath cards?

This is the output of the ifconfig command.

# ifconfig ath1 txpower 10
ifconfig: SIOCS80211TXPOWER: Invalid argument
# ifconfig ath1 txpower 20
ifconfig: SIOCS80211TXPOWER: Invalid argument
# ifconfig ath1 txpower 0
ifconfig: SIOCS80211TXPOWER: Invalid argument
# ifconfig ath0 txpower 0
ifconfig: SIOCS80211TXPOWER: Invalid argument
# ifconfig ath0 txpower 10
ifconfig: SIOCS80211TXPOWER: Invalid argument
# ifconfig ath2 txpower 10
ifconfig: SIOCS80211TXPOWER: Invalid argument

Obviously, the same error persists regardless the txpower argument value.


# dmesg
OpenBSD 3.9 (GENERIC) #617: Thu Mar  2 02:26:48 MST 2006
   [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II (GenuineIntel 686-class, 512KB L2 cache) 401 MHz
cpu0: 
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem  = 66625536 (65064K)
avail mem = 53170176 (51924K)
using 838 buffers containing 3432448 bytes (3352K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(92) BIOS, date 03/04/99, BIOS32 rev. 0 @ 0xfbc00
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf/0xc07c
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdef0/160 (8 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11 12
pcibios0: PCI Interrupt Router at 000:07:0 (Intel 82371SB ISA rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc/0x8000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 Intel 82443BX AGP rev 0x03
ppb0 at pci0 dev 1 function 0 Intel 82443BX AGP rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 ATI Rage Pro rev 0x5c
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 Intel 82371AB PIIX4 ISA rev 0x02
pciide0 at pci0 dev 7 function 1 Intel 82371AB IDE rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: QUANTUM FIREBALL ST3.2A
wd0: 16-sector PIO, LBA, 3079MB, 6306048 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 7 function 2 Intel 82371AB USB rev 0x01: irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 7 function 3 Intel 82371AB Power rev 0x02: polling
iic0 at piixpm0
xl0 at pci0 dev 14 function 0 3Com 3c905B 100Base-TX rev 0x30: irq
11, address 00:50:04:34:3b:2d
exphy0 at xl0 phy 24: 3Com internal media interface
ppb1 at pci0 dev 16 function 0 vendor Hint, unknown product 0x0021 rev 0x15
pci2 at ppb1 bus 2
ath0 at pci2 dev 8 function 0 Atheros AR5212 rev 0x01: irq 12
ath0: AR5213 5.6 phy 4.1 rf5111 1.7 rf2111 2.3, FCC2A*, address
00:0b:6b:34:95:a9
ath1 at pci2 dev 9 function 0 Atheros AR5212 rev 0x01: irq 5
ath1: AR5213 5.9 phy 4.3 rf5112 3.6, FCC2A*, address 00:0b:6b:4d:58:60
ath2 at pci2 dev 10 function 0 Atheros AR5212 rev 0x01: irq 10
ath2: AR5213 5.6 phy 4.1 rf5111 1.7 rf2111 2.3, FCC2A*, address
00:0b:6b:34:96:0c
eap0 at pci0 dev 20 function 0 Ensoniq AudioPCI97 rev 0x06: irq 5
ac97: codec id 0x54524103 (TriTech Microelectronics TR28023)
audio0 at eap0
midi0 at eap0: AudioPCI MIDI UART
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: PC speaker
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask e74d netmask ff6d ttymask ffef
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302



# ifconfig -a
lo0: flags=8049UP,LOOPBACK,RUNNING,MULTICAST mtu 33224
   groups: lo
   inet 127.0.0.1 netmask 0xff00
   inet6 ::1 prefixlen 128
   inet6 fe80::1%lo0 prefixlen 64 scopeid 0x8
xl0: flags=8943UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST mtu 1500
   lladdr 00:50:04:34:3b:2d
   media: Ethernet autoselect (100baseTX full-duplex)
   status: active
   inet 10.2.29.1 netmask 0xffc0 broadcast 10.2.29.63
   inet6 fe80::250:4ff:fe34:3b2d%xl0 prefixlen 64 scopeid 0x1
ath0: flags=8863UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST mtu 1500
   lladdr 

Re: Linphone installation

2006-06-08 Thread pedro la peu
On Thursday 08 June 2006 22:28, Stuart Henderson wrote:
 I've just been trying to get a softphone running too. You'll
 get a bit further using --with-osip=/usr/local/include but I haven't
 got the build to complete yet.

It works with ossaudio(3), except audio.

 Me too! I thought minisip looked the most interesting,
 but it looks like a right pig to build here.

They are all pigs, linphone might fly if it used audio(4).



Re: like the faq 14.16.1, partition is not in my disklabel ... need help anyway

2006-06-08 Thread Joachim Schipper
On Thu, Jun 08, 2006 at 08:31:59PM +, Didier Wiroth wrote:
 Hello,
 My ntfs amd comaq diag. partition is not in the disklabel.
 Unfortunately I don't know how to add correctly in the disklabel.
 I've read the faq 14.16.1 but it only shows a modification.
 
 Here is my fdisk output, which shows id 0 the ntfs partition:
 
 Disk: wd0   geometry: 12921/240/63 [195365520 Sectors]
 Offset: 0   Signature: 0xAA55
  Starting   Ending   LBA Info:
  #: idC   H  S -C   H  S [   start:  size   ]
 
 *0: 070   1  1 - 6800 239 63 [  63:   102831057 ] HPFS/QNX/AUX
  1: 12 12270   0  1 - 12920 239 63 [   185522400: 9843120 ] Compaq Diag.
  2: A6 6801   0  1 - 12269 239 63 [   102831120:82691280 ] OpenBSD
  3: 000   0  0 -0   0  0 [   0:   0 ] unused
 
 Here is current my disklabel:
 16 partitions:
 # sizeoffset  fstype [fsize bsize  cpg]
   a:   2097648 102831120  4.2BSD   2048 16384  328 # Cyl 102015 
 -104095
   b:   1024128 104928768swap   # Cyl 104096 
 -105111
   c: 195371568 0  unused  0 0  # Cyl 0 -193820
   d:   4194288 105952896  4.2BSD   2048 16384  328 # Cyl 105112 
 -109272
   e:   1024128 110147184  4.2BSD   2048 16384  328 # Cyl 109273 
 -110288
   f:   4194288 71312  4.2BSD   2048 16384  328 # Cyl 110289 
 -114449
   g:  10486224 115365600  4.2BSD   2048 16384  328 # Cyl 114450 
 -124852
   h:   4194288 125851824  4.2BSD   2048 16384  328 # Cyl 124853 
 -129013
   i:   2097648 130046112  4.2BSD   2048 16384  328 # Cyl 129014 
 -131094
   j:   3072384 132143760  4.2BSD   2048 16384  328 # Cyl 131095 
 -134142
   k:  50306256 135216144  4.2BSD   2048 16384  328 # Cyl 134143 
 -184049
 
 
 What do I have to add to disklabel to be able to access the ntfs and the 
 compaq diag partition?
 
 For ntfs something like:
 l: 102831057 63 unknown # Cyl ???
 
 I would really appreciate some help.
 
 Thank you very much !

Some noteworthy points:
1. Looks like you ran out of space in the disklabel (or in the
device namespace, or whatever): don't define this many disklabel slices
if you want to see the other partitions (which are typically numbered
from i). [I'm not 100% sure I'm correct here; please flame me, with the
correct answer if possible, if this is not the case.]
2. NTFS is not supported in GENERIC. This usually means the
implementation isn't really ready for prime time yet; you could build a
custom kernel, if you know what you are doing and have read most, if not
all, of FAQ 5.*.
3. I don't know what you want to do with the Compaq diag
partition, but it might not be too useful.

Joachim



Cryptography Accelerators

2006-06-08 Thread Breen Ouellette

Hello.

Given the recent post by Theo about the poor state of Hifn cooperation, 
I am curious to know how OpenBSD developers rate the other companies 
producing cryptography accelerators. The Cryptography page 
(http://www.openbsd.org/crypto.html) seems to be somewhat outdated, 
stating 'Hifn was initially a difficult company to deal with 
(threatening to sue us over our non-USA reverse engineering of their 
crypto unlock algorithm), but more recently they have been very helpful 
in providing boards and support'. Since this runs contrary to what Theo 
has said on the subject, I am wondering if the products from Broadcom or 
SafeNet are better supported. Or does it make more sense to shoot for a 
total solution like the VIA C3? Or are there other viable options?


Thanks.

Breeno



Re: Cryptography Accelerators

2006-06-08 Thread Stuart Henderson
On 2006/06/08 17:13, Breen Ouellette wrote:
 total solution like the VIA C3?

Not sure you can still get C3, Intel revoked VIA's license to use
the bus. Think they worked-around it by combining cpu and chipset into
the same chip for the 'corefusion' stuff and then there's the C7
with a new bus.

 Or are there other viable options?

Faster general-purpose cpu?



Re: Stability of bge on 3.8 SMP

2006-06-08 Thread Karl Kopp

Hi - we just had the exact same experience on a SMP AMD64 box with
OpenBSD 3.9. Anyone got any further on this?

On 3/23/06, Daniel Hamlin [EMAIL PROTECTED] wrote:

Daniel Hamlin wrote:
 I have a server acting as a router/firewall (dmesg below) that stopped
 passing traffic on one network card after being up for ~4 months.  The
 card was unpingable, and I believe the console said watchdog
 timeout.  Since the connection was down, I didn't take the time to
 write down the message, but instead rebooted the system.  Two days
 later the same thing happened.  I currently attribute it to bad
 hardware and have swapped out the server with another identical one.
 I'm not asking for the problem to be solved, since I know I don't have
 enough information, rather I want to know if I should use a different
 network card.  Should I just use the single processor kernel?  Or is
 there a work-around/configuration change that will guarantee me
 stability with this configuration?

 I found this while searching Google:
 
http://www.armorlogic.com/openbsd_information_server_compatibility_list.html?action=detailid=dl580g3


 which says OpenBSD 3.8 can boot on the machine, but seems to have
 various issues related to multiprocessor support and on-board Broadcom
 network interfaces.

 Thanks!

 Dan


 # cat hostname.bge0
 inet www.xxx.yyy.zzz 255.255.255.252 NONE
 # cat hostname.bge1
 inet aaa.bbb.ccc.ddd 255.255.255.248 NONE

 # ifconfig -a
 lo0: flags=8049UP,LOOPBACK,RUNNING,MULTICAST mtu 33192
groups: lo
inet 127.0.0.1 netmask 0xff00
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
 bge0: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST mtu 1500
lladdr 00:e0:81:30:ba:30
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet www.xxx.yyy.zzz netmask 0xfffc broadcast snip
inet6 snipbge0 prefixlen 64 scopeid 0x1
 bge1: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST mtu 1500
lladdr 00:e0:81:30:ba:31
groups: egress
media: Ethernet autoselect (1000baseT full-duplex)
status: active
inet aaa.bbb.ccc.ddd netmask 0xfff8 broadcast snip
inet6 snipbge1 prefixlen 64 scopeid 0x2
 pflog0: flags=141UP,RUNNING,PROMISC mtu 33192
 pfsync0: flags=0 mtu 1348
 enc0: flags=0 mtu 1536


 OpenBSD 3.8 (GENERIC.MP) #504: Sat Sep 10 16:02:38 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
 real mem = 4227395584 (4128316K)
 avail mem = 3632812032 (3547668K)
 using 22937 buffers containing 422948864 bytes (413036K) of memory
 mainbus0 (root)
 mainbus0: Intel MP Specification (Version 1.4) (TYAN S2881   )
 cpu0 at mainbus0: apid 0 (boot processor)
 cpu0: AMD Opteron(tm) Processor 248, 2191.74 MHz
 cpu0:
 
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,NXE,MMXX,LONG,3DNOW2,3DNOW

 cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB
 64b/line 16-way L2 cache
 cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully
 associative
 cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully
 associative
 cpu0: apic clock running at 199220473Hz
 cpu1 at mainbus0: apid 1 (application processor)
 cpu1: AMD Opteron(tm) Processor 248, 2191.43 MHz
 cpu1:
 
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,NXE,MMXX,LONG,3DNOW2,3DNOW

 cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB
 64b/line 16-way L2 cache
 cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully
 associative
 cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully
 associative
 mpbios: bus 0 is type PCI  mpbios: bus 1 is type PCI  mpbios: bus 2 is
 type PCI  mpbios: bus 3 is type PCI  mpbios: bus 4 is type ISA
 ioapic0 at mainbus0 apid 2: pa 0x86cbde24, version 11, 24 pins
 ioapic1 at mainbus0 apid 3: pa 0x86cbdd24, version 11, 4 pins
 ioapic2 at mainbus0 apid 4: pa 0x86cbdc24, version 11, 4 pins
 pci0 at mainbus0 bus 0: configuration mode 1
 ppb0 at pci0 dev 6 function 0 AMD 8111 PCI-PCI rev 0x07
 pci1 at ppb0 bus 3
 ohci0 at pci1 dev 0 function 0 AMD 8111 USB rev 0x0b: apic 2 int 19
 (irq 10), version 1.0, legacy support
 usb0 at ohci0: USB revision 1.0
 uhub0 at usb0
 uhub0: AMD OHCI root hub, rev 1.00/1.00, addr 1
 uhub0: 3 ports with 3 removable, self powered
 ohci1 at pci1 dev 0 function 1 AMD 8111 USB rev 0x0b: apic 2 int 19
 (irq 10), version 1.0, legacy support
 usb1 at ohci1: USB revision 1.0
 uhub1 at usb1
 uhub1: AMD OHCI root hub, rev 1.00/1.00, addr 1
 uhub1: 3 ports with 3 removable, self powered
 vga1 at pci1 dev 6 function 0 ATI Rage XL rev 0x27
 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
 wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
 AMD AMD8111 LPC rev 0x05 at pci0 dev 7 function 0 not configured
 pciide0 at pci0 dev 7 function 1 AMD 8111 IDE rev 0x03: DMA, channel
 0 

Re: like the faq 14.16.1, partition is not in my disklabel ... need help anyway

2006-06-08 Thread Tony Abernethy
Joachim Schipper wrote:

 On Thu, Jun 08, 2006 at 08:31:59PM +, Didier Wiroth wrote:
  Hello,
  My ntfs amd comaq diag. partition is not in the disklabel.
  Unfortunately I don't know how to add correctly in the disklabel.
  I've read the faq 14.16.1 but it only shows a modification.
 
  Here is my fdisk output, which shows id 0 the ntfs partition:
 
  Disk: wd0   geometry: 12921/240/63 [195365520 Sectors]
  Offset: 0   Signature: 0xAA55
   Starting   Ending   LBA Info:
   #: idC   H  S -C   H  S [   start:  size   ]
  
  *0: 070   1  1 - 6800 239 63 [  63:   102831057 ]
 HPFS/QNX/AUX
   1: 12 12270   0  1 - 12920 239 63 [   185522400: 9843120 ]
 Compaq Diag.
   2: A6 6801   0  1 - 12269 239 63 [   102831120:82691280 ] OpenBSD
   3: 000   0  0 -0   0  0 [   0:   0 ] unused
 
  Here is current my disklabel:
  16 partitions:
  # sizeoffset  fstype [fsize bsize  cpg]
a:   2097648 102831120  4.2BSD   2048 16384  328 #
 Cyl 102015 -104095
b:   1024128 104928768swap   #
 Cyl 104096 -105111
c: 195371568 0  unused  0 0  #
 Cyl 0 -193820
d:   4194288 105952896  4.2BSD   2048 16384  328 #
 Cyl 105112 -109272
e:   1024128 110147184  4.2BSD   2048 16384  328 #
 Cyl 109273 -110288
f:   4194288 71312  4.2BSD   2048 16384  328 #
 Cyl 110289 -114449
g:  10486224 115365600  4.2BSD   2048 16384  328 #
 Cyl 114450 -124852
h:   4194288 125851824  4.2BSD   2048 16384  328 #
 Cyl 124853 -129013
i:   2097648 130046112  4.2BSD   2048 16384  328 #
 Cyl 129014 -131094
j:   3072384 132143760  4.2BSD   2048 16384  328 #
 Cyl 131095 -134142
k:  50306256 135216144  4.2BSD   2048 16384  328 #
 Cyl 134143 -184049
 
 
  What do I have to add to disklabel to be able to access the
 ntfs and the compaq diag partition?
 
  For ntfs something like:
  l: 102831057 63 unknown # Cyl ???
 
  I would really appreciate some help.
 
  Thank you very much !

 Some noteworthy points:
   1. Looks like you ran out of space in the disklabel (or in the
 device namespace, or whatever): don't define this many disklabel slices
 if you want to see the other partitions (which are typically numbered
 from i). [I'm not 100% sure I'm correct here; please flame me, with the
 correct answer if possible, if this is not the case.]
16 partitions. That's a through p inclusive.
(also referred to as 15 partitions (excluding c))

   2. NTFS is not supported in GENERIC. This usually means the
 implementation isn't really ready for prime time yet; you could build a
 custom kernel, if you know what you are doing and have read most, if not
 all, of FAQ 5.*.
There are screweys, particularly on writitng.
I think Windows gets burned occasionally.

   3. I don't know what you want to do with the Compaq diag
 partition, but it might not be too useful.
I think it's an msdos partition
Called something different to keep Windows out of it.
Flames invited if I guessed wrong.


   Joachim



bge0 - Watchdog Timeout

2006-06-08 Thread Karl Kopp

Hi! We recently moved from a Cisco based router to OpenBSD and have
been wrapped. The only issue is that recently, every 2 days or so, the
OBSD 3.9 router stops moving packets and has to be rebooted. The
system is an dual AMD 64 with

The console reports bge0: Watchdog timeout

The console responsiveness is intermittent - I get 5 secons (ish) of
input before it freezes for around 10 seconds. This repeats over and
over.

Top says their is only 1 process on the queue.

ifconfig says all NICs are up and connected.

I'm at a loss where to start looking.

# ifconfig -a
lo0: flags=8049UP,LOOPBACK,RUNNING,MULTICAST mtu 33192
   groups: lo
   inet 127.0.0.1 netmask 0xff00
   inet6 ::1 prefixlen 128
   inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7
fxp0: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST mtu 1500
   lladdr 00:e0:81:32:06:57
   media: Ethernet autoselect (100baseTX full-duplex)
   status: active
   inet 10.1.1.17 netmask 0xff00 broadcast 10.255.255.255
   inet6 fe80::2e0:81ff:fe32:657%fxp0 prefixlen 64 scopeid 0x1
bge0: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST mtu 1500
   lladdr 00:ex:8x:3x:0x:a4
   groups: egress
   media: Ethernet autoselect (1000baseT full-duplex)
   status: active
   inet x.x.x.86 netmask 0xfffc broadcast x.x.x.87
   inet6 xe80::xe0:x1ff:xe32:xa4%bge0 prefixlen 64 scopeid 0x2
bge1: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST mtu 1500
   lladdr 00:ex:8x:3x:0x:a5
   media: Ethernet autoselect (1000baseT full-duplex)
   status: active
   inet y.y.y.254 netmask 0xff00 broadcast y.y.y.255
   inet6 xe80::xe0:x1ff:xe32:xa5%bge1 prefixlen 64 scopeid 0x3



Re: OpenBSD 3.9 on a Sun Fire x4100

2006-06-08 Thread Nick Shank
I have not put -current on this system. Would making this machine public and
available to developers be of any use? I would also include ilom access.
Thoughts?
 Nick



Re: OpenBSD 3.9 on a Sun Fire x4100

2006-06-08 Thread Nick Shank
Er, rather I have put current on the x4100. Hmmm... I must still be brain
dead from work...

-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of
Nick Shank
Sent: Thursday, June 08, 2006 6:54 PM
To: misc@openbsd.org
Subject: Re: OpenBSD 3.9 on a Sun Fire x4100

I have not put -current on this system. Would making this machine public and
available to developers be of any use? I would also include ilom access.
Thoughts?
 Nick



Re: squid and pf and dansguardian

2006-06-08 Thread Steven Surdock
Allen Theobald wrote:
 Greetings,
 
 I get transparent proxying with squid and pf.
 
 I get dansguardian and pf.
 
 What I don't get is squid, dansguardian, and pf.
 
 pf.conf fragment:
 
int_if=gem0
ext_if=kue0
 
# redirect to squid
rdr on $int_if inet proto tcp from any to any \
port www - 127.0.0.1 port 3128
 
## Allow the redirected connections to pass.
pass in on $int_if inet proto tcp from any to 127.0.0.1 \
port 3128 keep state
 
## Also, the proxy must be able to establish outgoing
 ## connections to external web servers.
pass out on $ext_if inet proto tcp from any to any \
port www keep state
 
pass quick on $int_if
 
 But now I want to put dansguardian on.  It listens on 8080, uses
 proxy port 3128. 
 
 How do these rules change?  I think I change 3128 to 8080 in the
 above rules.  But what happens to 3128?  Do I still need a 'pass in'
 rule for 3128? 
 
 Thanks and take care,

Short answer:  yes, change 3128 to 8080.  Nothing for 3128 if you're not
blocking connections to lo0.  Pass in if you restrict lo0.

Long(er) answer:
I found it helpful if I wanted to route around Dans to use the
'internal_pass' table and there were certain sites that just didn't like
squid so I use the oksites table.  But those are optional.  If you'll
just need to watch your rules to the lo0 interface (skip or pass quick).
The tun0 interface is for OpenVPN connections as I like the adzapping
that adzapper performs - http://adzapper.sourceforge.net/)

# Dan's Guardian
rdr on $int_if proto tcp from ! internal_pass to ! oksites port 80
- 127.0.0.1 port 8080
rdr on tun0 proto tcp from ! internal_pass to ! oksites port 80 -
127.0.0.1 port 8080

-Steve S.



Re: Combining boot floppies

2006-06-08 Thread Nick Holland
When I saw your note, I figured Something Ain't Right here.  I wasn't 
the only one.  Theo noticed.


I'm on a mission from Theo.

Michael White wrote:

Hi all,

I'm attempting my first install of OpenBSD (version 3.9) on an HP Omnibook 
800CT (Pentium 166, 80 MB RAM, 4.3 GB HD, 3COM 3CXEM556 Carbus Ethernet 
card), coming over from RH9.0.  One peculiarity of the 800CTs is that the 
SCSI CDROM is not bootable, so I'm down to booting with floppies.


whoa.  SCSI.  (he's right on this, btw...  Symbios Logic 53C810, if the 
page I'm reading is to be believed.)


I first attempted to boot from floppyC39.fs, since that's supposed to be the 
image for laptops.  Well, it does recognize my Ethernet card, but seems to 
choke on the hard drive.  After recognizing the Ethernet card, I see the 
following:


--
wd0(wdc0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
wd0(wdc0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
WARNING: preposterous time in file system
WARNING: file system time much less than clock time
--

After that, the machine is locked up.  So I boot from floppy39.fs instead.  
That had no problem with the hard drive.  I was able to successfully 
partition the drive.  But that image does not recognize my Ethernet card, so 
I'm unable to retrieve any images (didn't see an option for PPP).


The fact that floppy38.fs didn't see your network adapter is not 
unexpected, of course.


The fact that you had disk issues on floppyC39.fs is unexpected.  The 
fact that they go away on floppy39.fs is all the way to Just Plain Wrong.




Even after formatting the hard drive under the floppy39.s floppy, the 
floppyC39.fs floppy chokes on the hard drive.


Is there any way to combine the two capabilities? 


Not the way you are thinking.  But I have some ideas...

 The only reason I'm asking is because of a comment in the FAQ

(section 4.3):

Yes, there may be situations where one install disk is required to support 
your SCSI adapter and another disk is required to support your network 
adapter. Fortunately, this is a rare event, and can usually be worked 
around.


Worked around means combining hardware and install options in such a way 
that it is made to work...not fiddling with the boot media.  Usually.


I may have access to a Xircom network card - is that supported by the 
floppy39.s floppy?


No, the Xircom driver is not in floppy39.fs...
At least, not the Xircom driver I'm thinking of...they may have more 
than one. :)



Anyway...I'm sitting here looking at the config files that make up 
floppy39.fs and floppy39C.fs (RAMDISK and RAMDISKC, for those who want 
to follow along), and their diffs.


First, I see that the SCSI controller that is probably in your laptop is 
supported by the siop(4) driver, which is on floppy39.fs.  SO..the 
suggestion of dropping the file set on a CD and installing from that is 
probably workable.


But that's not what Theo sent me to ask.  We are interested in the 
reason for the problem more than a quick-and-dirty work-around. 
Besides, it is entirely possible the problem will be back with us when 
the full kernel loads.


So..back to the diff...  It sounds like there is something hurting the 
disk support on this thing.  So...we can try turning some drivers off, 
and see if that gets floppyC booting properly.  You do this using User 
Kernel Configuration, a.k.a., UKC:


  http://www.openbsd.org/faq/faq5.html#BootConfig

Here is a list of things to try disabling (disable bla at the ukc 
prompt):

   uhci*
   ohci*
   wdc*
Those you can do all at once.

h...  those were the only easy (a.k.a., mostly harmless) ones.

Well...if those don't improve things, let's try breaking some things:
   pciide*   (your disk performance now sucks)
   pcic* (that might kill your PCcard slot)
   cbb*  (if the above didn't, this will)
Do these one-at-a-time.

I'm not really sure what is going on...  You may have an issue with the 
PCcard/Cardbus support...which means your NIC may show up in the dmesg, 
but it may be just as non-functional as it is with floppy39.fs. 
Disabling pciide will cause a huge performance hit, but slow beats 
not working at all.


Might be interesting to see what happens if you boot without the NIC 
installed in the machine.  yeah, useless for your problem, but 
interesting for troubleshooting.



I'd love to see is a serial console capture of the output of the boot on 
this thing, from both the floppy39 and floppyC39 disks...but if you 
aren't fluent in serial, hooking one up for your first OpenBSD install 
might be a lot to ask for.  Ah, heck, if I don't ask, I won't get, right? :)


  http://www.openbsd.org/faq/faq4.html#getdmesg

You can probably at least get the dmesg from floppy39.fs to a floppy 
disk using the process there, but if you can get both by using a serial 
cable, all the better...


Nick.



  1   2   >