Hello,
Next time sky2 hangs on me I'll try to reset the PHY and see if that
helps. I can usually trigger the hang by doing a couple of ifconfig
up/down on the interface, though I'm not getting any error message
from the driver when that happens.
same for me. In dmesg is absolut nothing. I
Hello Sam,
Is this heavy Tx load (ie your watching movie from mac mini). or Rx
load (you are watching movie on mac mini).
it's inbound (Rx) traffic. Watching a Movie, git pull from linus, or scp
kernel tar tree from my laptop to my mac mini.
Thomas
-
To unsubscribe from this list:
Hello Stephen,
It was intentional in 2.6 to allow interfaces to be hot-removed.
Remember with Internet protocols there is no hard binding (normally)
between address and device and connections should not go down if link
fails.
of course. That makes sense. I just wondered when the change in
Hello,
I have a sky2 network card in my intel mac mini. It stops working when I
do havy network load like watching a divx over http/sshfs. However if I
remove the driver module and load it again it works and even the tcp
connection doesn't get shutdown. I automated the above procedure using
a
Hello Fagyal,
- a previously suggested fix - passing idle=poll to the kernel - did not
work for me at the end
same for me. I tried the two module parameters and the kernel parameter:
pci=nomsi sky2.disable_msi=1 sky2.idle_timeout=1000
- the locks I have happen very periodically (somewhere
Hello Stephen,
I can reproduce the problem now (on mac mini). Interestingly it seems
to whack the whole ethernet switch when it happens.
wow. I have Linksys wrt54g has 'ethernet switch' and my Snom 320 VoIP
phone still works when the mini network card goes down. On the other
side the wrt54g
Hello Stephen,
thanks for the fix, it fixes the problem for me. I closed the bug. On
which hardware did you reproduce the bug and how did you found it? Did
you use git bisect?
Thomas
-
To unsubscribe from this list: send the line unsubscribe netdev in
the body of a message to [EMAIL
Hello,
Is this fix in your version?
http://www.mail-archive.com/netdev@vger.kernel.org/msg18603.html
I put this one in and recompiled and I am *still* able to reproduce the
problem.
Thomas
-
To unsubscribe from this list: send the line unsubscribe netdev in
the body of a message
Hello,
[resent because forget to CC netdev ]
Something is happening long before you start doing ipv6. The parity
error's mean that the PCI transfers are going south. The driver might
be better to just shut it self off after that.
I can ssh off the machine for days. But
Hello,
[ resend because .config and the used kernel version was missing ]
Linux Kernel Version: Linus Vanilla Tree; .config attached.
I recently aquired a Lenovo (IBM) T60 with a e1000 network card. I
experience high latency with this networkcard: Pings last upto 1 second
where the ping
Hello Auke,
CONFIG_IRQBALANCE=y
thanks for the feedback. The behaviour improoved. In my first tests it
wasn't so good. But now it seems perfect:
(thinkpad) [~] ping 131.188.30.102
PING 131.188.30.102 (131.188.30.102) 56(84) bytes of data.
64 bytes from 131.188.30.102: icmp_seq=1 ttl=64
Hello,
I recently aquired a Lenovo (IBM) T60 with a e1000 network card. I
experience high latency with this networkcard: Pings last upto 1 second
where the ping should be around 25 ms. I googled a bit and found the
following:
- Enable NAPI, which didn't worked for me.
64 bytes from
Hello,
http://developer.osdl.org/shemminger/prototypes/sky2-1.3-rc1.tar.bz2
v0.15:
64 bytes from 10.0.0.138: icmp_seq=2 ttl=64 time=0.467 ms
v1.3-rc1:
64 bytes from 10.0.0.138: icmp_seq=4 ttl=64 time=32.9 ms
I can't confirm this. For me it is just perfect:
64 bytes from 89.106.66.1:
13 matches
Mail list logo
