Re: [Nut-upsuser] Tripp Lite Internet Office 350VA

2005-12-06 Thread Charles Lepple
, trimmed to only show the UPS)? thanks, -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Atlantis-Land UPS with Cypress CY7C63723 chip (cypress_m8 driver) support

2005-12-07 Thread Charles Lepple
, posting a couple technical tidbits here shouldn't be much of a problem. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Xserve, USB, NUT

2006-01-04 Thread Charles Lepple
driver? You will need to use newhidups - the older hidups driver will not work on platforms other than Linux. You also need to install libusb, and pass the installation location to ./configure when you build NUT. -- - Charles Lepple ___ Nut-upsuser

Re: [Nut-upsuser] Re: Xserve, USB, NUT

2006-01-07 Thread Charles Lepple
On 1/7/06, Charles Lepple [EMAIL PROTECTED] wrote: Do you remember what version of libusb you used with 2.0.2? (still applicable, but I realized that you did say you got 2.0.2 working on the Xserve, so the question below is moot.) This partially-working state was on the Xserve as well, correct

Re: [Nut-upsuser] Re: Xserve, USB, NUT

2006-01-07 Thread Charles Lepple
the system UPS driver from grabbing your UPS (subsequently allowing access via libusb, and therefore NUT), you need a dummy kernel extension. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org

Re: [Nut-upsuser] SOHO Serial Solution needed

2006-01-23 Thread Charles Lepple
that uses higher-frequency components (eliminating the transformer) and a lighter battery, but it would probably be more expensive than most would be willing to pay. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http

Re: [Nut-upsuser] UPSD slow in responding

2006-02-07 Thread Charles Lepple
of the backup process (since most OSes, by default, do not schedule disk I/O with priorities that account for the system-specific delay in waiting for disk reads and writes). -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] TrippLite SmartPro and 2.0.3

2006-02-08 Thread Charles Lepple
, or if there is a setting in the BIOS for legacy device support (sometimes this confuses the kernel), or even whether loading ehci_hcd fixes things. (Even if you only plan on using the UHCI or 12 Mbps part of the USB controller, sometimes there are issues with the EHCI/UHCI handoff.) -- - Charles

Re: [Nut-upsuser] Tripp Lite is up to no good

2006-02-08 Thread Charles Lepple
it with the existing driver, though. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Status of tripplite_usb driver?

2006-02-22 Thread Charles Lepple
ownership of the appropriate /proc/bus/usb/XYZ/ABC node (best done in hotplug scripts, because some devices occasionally disconnect due to noise on the USB lines). The hotplug stuff depends on your particular distribution. -- - Charles Lepple ___ Nut

Re: [Nut-upsuser] Misreported values with newhidups

2006-03-04 Thread Charles Lepple
inclined to leave it be. This looks normal for a pair of 12V lead-acid batteries in series. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] nut on Mac OS X. Where to put upsdrvctl shutdown?

2006-03-10 Thread Charles Lepple
back to the OS. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] nut on Mac OS X. Where to put upsdrvctl shutdown?

2006-03-16 Thread Charles Lepple
. The meta-driver idea that I was describing could work here - after catching the low-battery event, the driver could stall the OS from shutting down until the slave systems were notified. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] APC Back-UPS XS 1200

2006-03-17 Thread Charles Lepple
- you will see much more information if you use upsc. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] newhidups driver process crashed shortly after upsd loads

2006-03-17 Thread Charles Lepple
on the road for a while. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Adding tripplite smart1500 UPS to tripplite_usb

2006-03-17 Thread Charles Lepple
with states like on AC, on battery, low battery, outlets off, etc. with the corresponding ups.debug.S value. Let me know if you need help. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org

Re: [Nut-upsuser] TrippLite SmartPro UPS and nut-2.0.2

2006-04-01 Thread Charles Lepple
). The SMART1500RM2U (which I assume is just a smaller version of the 3000RM2U) has a USB plug on the back - would that work for your setup? The tripplite_usb driver is still a work-in-progress, but it does detect the 1500. -- - Charles Lepple ___ Nut-upsuser

Re: [Nut-upsuser] nut on Mac OS X. Where to put upsdrvctl shutdown?

2006-04-02 Thread Charles Lepple
to verify this theory. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Just to monitor an UPS

2006-04-03 Thread Charles Lepple
, you can use 'upsc [EMAIL PROTECTED]'. For automatic shutdown, you probably want to check the documentation. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] newhidups crashes intermittently (double free or corruption)

2006-04-04 Thread Charles Lepple
, or straight from source? Also, does the driver dump core? -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Powerware 9120 not seen by newhidups driver?

2006-04-07 Thread Charles Lepple
, and it will not provide enough information to upsd to actually monitor or shut down a system. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] New UPS protocol choice - Dynamix

2006-04-08 Thread Charles Lepple
On 4/7/06, Criggie [EMAIL PROTECTED] wrote: The best method I've found is trial and error which sounds a bit last-resort. Is there any better way to find out what protocol is used? If you have drivers for another OS, you can observe the communication between the host and the UPS. -- - Charles

Re: [Nut-upsuser] Setting up NUT to monitor under OS X?

2006-04-17 Thread Charles Lepple
to hear about it on the list. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Ablerex MARS

2006-04-22 Thread Charles Lepple
), and try to fit the curve. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Gamatronic UPS using nut 2.0.3

2006-05-01 Thread Charles Lepple
On 5/1/06, Shlomo Dubrowin [EMAIL PROTECTED] wrote: Does anyone know why, or how to check why, it is showing OB, when it should be showing OL? I am not familiar with the various genericups types, but you can use statserial to show the status of the various serial port lines. -- - Charles

Re: [Nut-upsuser] Gamatronic UPS using nut 2.0.3

2006-05-01 Thread Charles Lepple
://boxster.ghz.cc/projects/nut has the latest source code, in case you haven't checked the development branch yet (in trunk/). -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut

Re: [Nut-upsuser] Gamatronic UPS using nut 2.0.3

2006-05-01 Thread Charles Lepple
to construct a custom genericups configuration. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

[Nut-upsuser] Re: old Powercom UPS

2006-05-01 Thread Charles Lepple
the lines from the serial connector back to the circuitry. All merely suggestions, of course - don't blame me if you get zapped :-) -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org

Re: [Nut-upsuser] No USB/HID UPS found

2006-05-08 Thread Charles Lepple
similar routines to talk to libusb. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Tripp Lite OMNI1000LCD

2006-05-11 Thread Charles Lepple
(firewall, etc.), let me know and I will make another snapshot. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] NUT 2.0.3 ups.conf serial comms to an MGE Ellipse

2006-05-15 Thread Charles Lepple
- [mge] - to delimit a new section in the file. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] upssched does not start the script when timer triggers

2006-05-17 Thread Charles Lepple
On 5/17/06, Charles Lepple [EMAIL PROTECTED] wrote: have you checked this: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-May/000899.html ignore that one... what happens if you type 'file /etc/nut/upsalert'? -- - Charles Lepple ___ Nut

Re: [Nut-upsuser] upssched does not start the script when timer triggers SOLVED

2006-05-17 Thread Charles Lepple
reporting system - there is a thread on nut-upsdev about this. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Tripplite SU2200XL

2006-05-17 Thread Charles Lepple
of the source file: http://boxster.ghz.cc/projects/nut/browser/trunk/drivers/tripplitesu.c -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Difficulty over USB with a CyberPower 800AVR and nut 2.0.3

2006-05-18 Thread Charles Lepple
has a debug dump for new USB/HID UPSes, but unfortunately that feature isn't included in 2.0.3. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Question about slave shutdown

2006-05-30 Thread Charles Lepple
On 5/30/06, Chris Wang [EMAIL PROTECTED] wrote: It seems that the slave can't receive the FSD signal, and I didn't see the master send FSD to the slave. Perhaps something is wrong with my configuration. Please send some of your configuration files to the list. -- - Charles Lepple

Re: [Nut-upsuser] Eaton USB PowerWare 3105

2006-06-06 Thread Charles Lepple
, and apparently the port name just has to be some placeholder value (the man page suggests auto). (Not saying that you should change anything, just that there is no connection.) -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org

Re: [Nut-upsuser] NUT on AIX 5.2 with Tripplite_usb?

2006-06-07 Thread Charles Lepple
not one of those things that they provide emulation support for. I have not used AIX in about ten years, though, so I don't know. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman

Re: [Nut-upsuser] nutups with MGE Evolution via USB

2006-06-09 Thread Charles Lepple
? Are they plugged into the same external or root hub? -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Tripp Lite OMNIVS1500XL Unknown protocol

2006-06-27 Thread Charles Lepple
, you should probably use the scripts/hotplug directory in the nut source tarball. (If sarge uses hotplug-ng, there is another directory for that, too). Email the list if you run into trouble. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] Hi all

2006-07-10 Thread Charles Lepple
@ with nut . Worked just last week on a mixed sarge/testing box. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Tripp Lite Smart1000LCD driver problem

2006-07-24 Thread Charles Lepple
What does /proc/bus/usb/devices say about the UPS? -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Problems with config of newhidups

2006-07-25 Thread Charles Lepple
On 7/25/06, Tom Diehl [EMAIL PROTECTED] wrote: I installed the libhidups and libhid.usermap per the README. Unfortunately, the libhid.usermap file doesn't change permissions on all systems (particularly those that use udev). What version of Fedora Core is RHEL4 most similar to? -- - Charles

[Nut-upsuser] Re: Problems with config of newhidups

2006-07-25 Thread Charles Lepple
On 7/25/06, Tom Diehl [EMAIL PROTECTED] wrote: EL4 does use udev. Sure wish I understood it. :-( In that case, you need the rules in the hotplug-ng directory. I guess we should rename that to udev at some point... -- - Charles Lepple ___ Nut

Re: [Nut-upsuser] Error during make: *** No rule to make target `usb.h', needed by `tripplite-hid.o'. Stop.

2006-07-27 Thread Charles Lepple
revision number uniquely identifies the state of the repository, it does not identify which branch you are working on. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut

Re: [Nut-upsuser] CyberPower CP1200AVR/BC1200D problems

2006-07-27 Thread Charles Lepple
after the device check (which itself it troubling). The first time we try to claim the device, the kernel usbhid driver is still in control. After detaching the driver, the claim succeeds The timeout afterwards is what concerns me. -- - Charles Lepple

[Nut-upsuser] Re: Mac Clients for nut

2006-07-28 Thread Charles Lepple
list, though. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Gentoo Ultra USB UPS

2006-07-30 Thread Charles Lepple
On 7/30/06, Barry Fawthrop [EMAIL PROTECTED] wrote: Can't start /lib/nut/(null): No such file or directory Please post your config files. Also note that the hidups driver is deprecated, and will go away in a future release. A more comprehensive driver is newhidups. -- - Charles Lepple

[Nut-upsuser] Re: Mac Clients for nut

2006-07-30 Thread Charles Lepple
you need to follow these instructions to get it to install: http://www.finkproject.org/faq/usage-fink.php#unstable This package is bare-bones, in that I have not supplied any startup or shutdown scripts. If you happen to try this package, let me know how it works. -- - Charles Lepple

Re: [Nut-upsuser] Gentoo Ultra USB UPS

2006-07-31 Thread Charles Lepple
On 7/31/06, Barry Fawthrop [EMAIL PROTECTED] wrote: ups.conf = [Ultra1] DRIVER = hidups PORT = /dev/usb/hiddev0 I believe driver and port should be lowercase. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] Gentoo Ultra USB UPS

2006-07-31 Thread Charles Lepple
On 7/31/06, Barry Fawthrop [EMAIL PROTECTED] wrote: /dev/usb/hiddev0 is the UPS I'm sure (but not 100%) It may be that it is just a simple USB-to-serial converter, and not a standards-compliant PDC UPS. Can you post the output from running 'lsusb -vvv' as root? -- - Charles Lepple

Re: [Nut-upsuser] Gentoo Ultra USB UPS

2006-07-31 Thread Charles Lepple
On 7/31/06, Barry Fawthrop [EMAIL PROTECTED] wrote: No matching USB/HID UPS found Driver failed to start (exit status=1) Please see the newhidups man page for generic mode, which allows newhidups to bind to UPSes that it does not know about. -- - Charles Lepple

Re: [Nut-upsuser] Networked APC

2006-08-01 Thread Charles Lepple
of failure, though, since you probably only want one machine commanding the UPS to power down. (A data center could avoid this with dual-input power supplies fed from separate UPSes.) Someone else who is more familiar with snmp-ups may have more insight into this. -- - Charles Lepple

Re: [Nut-upsuser] Networked APC

2006-08-01 Thread Charles Lepple
On 8/1/06, Matthew Isleb [EMAIL PROTECTED] wrote: On Aug 1, 2006, at 11:05 AM, Charles Lepple wrote: You still may end up with a single point of failure, though, since you probably only want one machine commanding the UPS to power down. (A data center could avoid this with dual-input power

Re: [Nut-upsuser] Networked APC

2006-08-01 Thread Charles Lepple
On 8/1/06, Charles Lepple [EMAIL PROTECTED] wrote: On 8/1/06, Matthew Isleb [EMAIL PROTECTED] wrote: On Aug 1, 2006, at 11:05 AM, Charles Lepple wrote: You still may end up with a single point of failure, though, since you probably only want one machine commanding the UPS to power down

Re: [Nut-upsuser] nut-usb fink version

2006-08-02 Thread Charles Lepple
now, I do not know of a way to tell the system not to try and connect to the UPS (so that NUT can connect instead), so there may be some interactions here. Can you start the driver like this: /sw/bin/newhidups -u root -DDD and paste some of the output? -- - Charles Lepple

Re: [Nut-upsuser] choosing a UPS (in the United States)

2006-08-08 Thread Charles Lepple
of the other vendors' hidden features. Some of the APC fixes are very recent, though, and have not been tested as much. Froogle lists several MGE distributors in the US, so it's worth another look. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] choosing a UPS (in the United States)

2006-08-08 Thread Charles Lepple
On 8/8/06, Eric S. Johansson [EMAIL PROTECTED] wrote: Charles Lepple wrote: On 8/8/06, Eric S. Johansson [EMAIL PROTECTED] wrote: I do a bunch of kindness of strangers hosting in my basement and my three kVA apc unit died recently. In looking around, it looked like Belkin was a reasonable

Re: [Nut-upsuser] Perl UPS::Nut interface

2006-08-11 Thread Charles Lepple
, there was a non-hierarchical list of variables, and I believe some other aspects of the protocol changed as well. Details are in docs/protocol.txt. If there is sufficient interest, we could use SWIG to generate Perl/Python/language-du-jour bindings from libupsclient. -- - Charles Lepple

Re: [Nut-upsuser] Can't get stuff to start automatically.

2006-08-15 Thread Charles Lepple
(be sure to restart syslogd afterwards). You can also run rc.d scripts by hand via 'sh -x', which prints every line as it is executed. Something like ths should work: # sh -x /etc/init.d/nut start -- - Charles Lepple ___ Nut-upsuser mailing list Nut

Re: [Nut-upsuser] Problem detecting USB/HID UPS

2006-08-16 Thread Charles Lepple
the name, tripplite_usb will not work for newer Tripp Lite UPSes, especially if the product id is not 0001 - use newhidups instead. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman

Re: [Nut-upsuser] Problem detecting USB/HID UPS

2006-08-17 Thread Charles Lepple
SYSFS{bConfigurationValue}==1 SYSFS{bNumInterfaces}== 1 [some information about hubs and host controllers snipped] -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo

Re: [Nut-upsuser] Shutdown after 5 minutes?

2006-08-25 Thread Charles Lepple
-- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] tripplite_usb

2006-08-25 Thread Charles Lepple
On 8/25/06, Rob Harris [EMAIL PROTECTED] wrote: - VendorID: 09ae - ProductID: 2005 For Tripp-Lite product IDs other than 1, please use the newhidups driver instead. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] tripplite_usb

2006-08-26 Thread Charles Lepple
On 8/25/06, Rob Harris [EMAIL PROTECTED] wrote: Charles Lepple wrote: On 8/25/06, Rob Harris [EMAIL PROTECTED] wrote: - VendorID: 09ae - ProductID: 2005 For Tripp-Lite product IDs other than 1, please use the newhidups driver instead. No dice... Sorry, I thought the Tripp-Lite HID

Re: [Nut-upsuser] suse linux and nut

2006-08-26 Thread Charles Lepple
for the port when using newhidups. We are currently using libusb for portability, so the appropriate device node is somewhere in either /dev/bus/usb or /proc/bus/usb (on older systems). -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] Slightly OT: Generators UPS

2006-09-01 Thread Charles Lepple
load (light bulbs, or a computer). How much of this is attributable to low inductance versus low load is up for grabs, but with the push for unity power factor on PC power supplies, I would lean towards low load. -- - Charles Lepple ___ Nut-upsuser

Re: [Nut-upsuser] Smart-UPS with SuSE 9.0/Nut

2006-09-07 Thread Charles Lepple
On 9/7/06, Chris Boyd [EMAIL PROTECTED] wrote: Anyone have any ideas? Not for NUT 1.2, no. That version is very old, and a number of fundamental changes have been made since then. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] Tripp Lite OMNI900LCD

2006-09-08 Thread Charles Lepple
SVN are here: http://www.networkupstools.org/source.html This will hopefully make it into the 2.0.5 release, but I imagine there is a bit of backporting to do. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http

Re: [Nut-upsuser] Query SNMP

2006-09-13 Thread Charles Lepple
MIB), I get values back on whatever I queried (voltage, battery, etc). Somebody was looking at writing an SNMP agent that would do that, but it has not made its way into the core NUT distribution. Arnaud, do you know the status of the agent? -- - Charles Lepple

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status

2006-09-18 Thread Charles Lepple
of the status values to NUT ups.status lines. Would you have time to do some off-line testing with this UPS, or is it powering something mission-critical right now? -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status

2006-09-18 Thread Charles Lepple
On 9/18/06, Jeff Knerr [EMAIL PROTECTED] wrote: On Mon, Sep 18, 2006 at 11:48:32AM -0400, Charles Lepple wrote: Attached to Tripp Lite SMART2200RMXL2U Unknown value for s[2]: 0x34 That's the culprit. I have not had much testing time with the RM2U-style UPSes, so I was not able

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status -- first test

2006-09-18 Thread Charles Lepple
they were reporting status. I decoded the status bits for the OMNI1000VS, but it seems to have a different interpretation for S[2] than the SMART...RM2U series. I'll take a closer look later. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status

2006-09-18 Thread Charles Lepple
On 9/18/06, Jeff Knerr [EMAIL PROTECTED] wrote: Unknown battery voltage: 0x3038 Do you know the battery configuration for this unit? I think it translates to a nominal battery voltage of 48V (expressed in 6V steps). -- - Charles Lepple ___ Nut

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status

2006-09-18 Thread Charles Lepple
I added some more code to SVN trunk (rev 527). Let me know how it goes. You might not want to limit it to just ups.debug, as I tried to apply some old protocol notes to decoding the values that come back. -- - Charles Lepple ___ Nut-upsuser mailing

Re: [Nut-upsuser] apcsmart constant read failure errors

2006-09-21 Thread Charles Lepple
On 9/21/06, Chris Cameron [EMAIL PROTECTED] wrote: Anyone know what I can do to get this thing to quit complaining? Does 'upsc [EMAIL PROTECTED]' actually return anything? Can you tell us a little more about your system? -- - Charles Lepple

Re: [Nut-upsuser] apcsmart constant read failure errors

2006-09-21 Thread Charles Lepple
, but I'm not sure where that went. It's a simple fix in the source, though. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status

2006-09-22 Thread Charles Lepple
On 9/22/06, Jeff Knerr [EMAIL PROTECTED] wrote: On Mon, Sep 18, 2006 at 10:41:58PM -0400, Charles Lepple wrote: On 9/18/06, Jeff Knerr [EMAIL PROTECTED] wrote: Unknown battery voltage: 0x3038 Do you know the battery configuration for this unit? I think it translates to a nominal

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status (second test)

2006-09-22 Thread Charles Lepple
On 9/22/06, Jeff Knerr [EMAIL PROTECTED] wrote: On Mon, Sep 18, 2006 at 11:56:09PM -0400, Charles Lepple wrote: I added some more code to SVN trunk (rev 527). Let me know how it goes. You might not want to limit it to just ups.debug, as I tried to apply some old protocol notes to decoding

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status (second test)

2006-09-26 Thread Charles Lepple
On 9/22/06, Jeff Knerr [EMAIL PROTECTED] wrote: On Mon, Sep 18, 2006 at 11:56:09PM -0400, Charles Lepple wrote: I added some more code to SVN trunk (rev 527). Let me know how it goes. You might not want to limit it to just ups.debug, as I tried to apply some old protocol notes to decoding

Re: [Nut-upsuser] tripp lite SMART2200RMXL2U -- empty ups.status (third test)

2006-09-28 Thread Charles Lepple
it sees the OB LB line. OK. Email the lists if you run into trouble - you don't need any fancy scripting or upssched stuff to do what you're trying to do. Thanks for helping me get this working! You provided some excellent test data. Thank you! -- - Charles Lepple

Re: [Nut-upsuser] MGE Pulsar M 3000 communication problems [USB]

2006-09-28 Thread Charles Lepple
that there was a port of libusb for versions of Solaris before 10, but I haven't been following this closely.) -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut

Re: [Nut-upsuser] OL/OB on RD

2006-10-12 Thread Charles Lepple
to a modem status pin. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] nut 2.0.4 won't compile on AIX 5.3

2006-10-18 Thread Charles Lepple
. What is the error when compiling dummycons.c? -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] nut 2.0.4 won't compile on AIX 5.3

2006-10-18 Thread Charles Lepple
On 10/18/06, Jurjen Oskam [EMAIL PROTECTED] wrote: On Wed, Oct 18, 2006 at 08:03:21AM -0400, Charles Lepple wrote: Since the drivers are separate executables, you can run 'make -k' to have it build as much as it can (instead of stopping at the first error). You will still see errors, but all

Re: [Nut-upsuser] Adding TrippLite SMART550 / Protocol 2001 Support

2006-10-19 Thread Charles Lepple
this. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] NUT with APC RS 500 in Debian

2006-10-21 Thread Charles Lepple
these drivers. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Bug in file parsing of ups.conf

2006-10-23 Thread Charles Lepple
/index.php?func=detailaid=304024group_id=30602atid=411542 -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] MGE Ellipse Premium 1200 USB cable only works if plugged after boot

2006-11-02 Thread Charles Lepple
script. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Re: [Nut-upsdev] megatec driver and usb-to-serial converters

2006-11-02 Thread Charles Lepple
by the usbserial driver in Linux. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] MGE Ellipse Premium 1200 USB cable only works if plugged after boot

2006-11-02 Thread Charles Lepple
heh, ignore my ramblings, I found the rest of the thread :-) On 11/2/06, Charles Lepple [EMAIL PROTECTED] wrote: On 11/2/06, Pedro CĂ´rte-Real [EMAIL PROTECTED] wrote: On 11/2/06, Kjell Claesson [EMAIL PROTECTED] wrote: Hi Pedro, Hi It depends on what dist of Linux you are running

Re: [Nut-upsuser] Calibrating the Battery on an MGE Ellipse Premium 1200

2006-11-04 Thread Charles Lepple
: $ upsrw [EMAIL PROTECTED] The battery.charge.low might be set to a high percentage. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] EMC/ACBEL Polytech UPS

2006-11-05 Thread Charles Lepple
firsthand experience with these drivers. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] EMC/ACBEL Polytech UPS

2006-11-05 Thread Charles Lepple
with minicom or some other terminal app? Potentially, but many UPS protocols are binary. If you do use minicom, be sure that both hardware and software flow control are off. gtkterm has a hex input window if needed. -- - Charles Lepple ___ Nut-upsuser mailing

Re: [Nut-upsuser] Sweex 1000VA UPS

2006-11-08 Thread Charles Lepple
check the system logs for error messages. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] Sweex 1000VA UPS

2006-11-11 Thread Charles Lepple
. Then, if you simply do not start upsmon, you can discharge the battery completely without shutting down the system which is monitoring the UPS. 'upsc' only needs the driver and 'upsd', as you found out. -- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser

Re: [Nut-upsuser] Spurious messages on start

2006-11-12 Thread Charles Lepple
-- - Charles Lepple ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser

Re: [Nut-upsuser] (no subject)

2006-11-15 Thread Charles Lepple
: probe of 2-1:1.0 failed with error -5 actually, this part is normal. The device is blacklisted from the kernel usbhid driver so that it can be claimed in userspace by newhidups. Did you see any error messages from the driver or other NUT components? -- - Charles Lepple

Re: [Nut-upsuser] Recommendation for big UPS (was CyberPower PR2200)

2006-11-16 Thread Charles Lepple
, and it seems to be showing online/onbattery, so until I finish a smart driver, that one should work. ___ Nut-upsuser mailing list Nut-upsuser@lists.alioth.debian.org http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser -- - Charles Lepple

Re: [Nut-upsuser] Tripp light driver?

2006-11-27 Thread Charles Lepple
automatically. Let me know if you have requests for new features or bug fixes. I am working on a solution for monitoring multiple SMARTPRO units, and eventually we will improve the error messages regarding the USB device nodes. -- - Charles Lepple

  1   2   3   4   5   6   7   8   9   10   >