The nodes for the controlling input of the controlled sources are set in
brackets in the models supplied from analog devices, like Gx 1 0 (2,0) 1
Try without brackets like Gx 1 0 2 0 1.
The analog models from protel are ok like this.
I think there is an article in the protel knowledge base that
Iris,
the TLC271 has programmable bias setting capability. If you do not need this
feature for simulation take the LMC6081 from National, which is close to the
Texas OP. The model is supplied by protel with the standard simulation
models for OPAMPS, to be found in the ..\Design Explorer 99
Iris,
yes, i have seen this too.
It seems to be a bug, because the simulation results look ok.
Lets report it to Protel.
GMIN is one of the spice variables. Actually its the conductance (1/R) of
the resistors that spice places in parallel with any semiconductor p-n
junction during the simulation
The TLC271 has programmable bias setting capability. If you do not need this
feature for simulation take the LMC6081 from National, which is close to the
Texas OP. The model is supplied by protel with the standard simulation
models for OPAMPS, to be found in the ..\Design Explorer 99
engine which is
an 'enhanced and extended version of Spice3'. But its backward compatible to
Spice, so you can use every 'real' Spice model.
Rolf Molitor
i2e Systemelektronik
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Fabian Hartery [EMAIL PROTECTED]
An: 'Protel EDA Forum' [EMAIL
the
system. Best way may be to remove all printer drivers, reinstall them one by
one, starting with your preferred protel printer and try printing until you
find the troublemaker. If none works, you have to reinstall protel
first.
Rolf Molitor
i2e Systemelektronik
Remscheid / Germany
be much much more
useful. I am getting angry when i see these ugly grey boxes and can not do
anything against them. What about a handful of additional models in every SP
? That shouldnt be to difficult ?
Rolf Molitor
Systemelektronik i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von
Ken,
please be more specific, what parts do not work ?
There were some problems in the past concerning the transformer library but
i think that this has been fixed. Some of the models may still use pspice
syntax which is not compatible with the xspice engine of protel.
Rolf Molitor
documentation about XSPICE from the University of
Georgia/Atlanta. Do a search about XSPICE with google and you will find many
information about that.
We were looking for good books about XSPICE some time ago and found none.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht
The license number 99xx worked for me.
It is important to enter the name/company exactly as it is in the altium
customer database.
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Andrew Ircha [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED
Happy new year.
??
What means 'schematic translated to edif2.0' if it dose not mean 'create
netlist in edif2.0', what should be no problem ??
Rolf Molitor
Ingenieurbuero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Dennis Saputelli [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL
The settings are stored in a [schematic_name].cfg file, which usually is
located in the same folder as the schematic (when using the ddb-system).
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Jason Morgan [EMAIL PROTECTED]
An: Protel EDA Forum (E-mail
When did you get them ?
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Ben Uijtenhaak [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Dienstag, 15. Januar 2002 11:02
Betreff: Re: [PEDA] Tasking tools
Yes!
Ben Uijtenhaak
[EMAIL
is the troublemaker (hopefully not your default
printer).
Rolf Molitor
Ingenieurbuero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Montag, 21. Januar 2002 17:36
Betreff: [PEDA] Illegal Operation crash
Hello all
start at the end of february.
He apologized for the delay and offered me a demo version to play with until
the real thing arrives.
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Mark Richards [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet
I hope that it will be possible to edit 3D models in the (soon coming)
Phoenix.
Do not wait for such an upgrade for P99SE.
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Tommy Åkesson [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet
. Postscript), using a
Windows standard postscript printer like Linotronic100. Then import the
EPS-file to Corel Paint (!) and export it as .GIF-file (or .bmp or .tif or
...). Then import it as graphics to Word. Works great for me.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
Peder,
you can find some information about semiconductor footprints here (Philips):
http://www-us8.semiconductors.com/acrobat/various/SC01_MOUNTING_1996_1.pdf
R.Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Peder K. Hellegaard [EMAIL PROTECTED]
An: Protel EDA
Write macros for that purpose and place them in the templates.ddb.
I think you can already find an example macro for changing layers there.
Then assign your macros to keys under customize/shortcut keys.
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Yuriy
by the protel simulator.
There is not much literature about XSpice available in the net, the original
manual comes from the georgia institute of technology in
atlanta/georgia/usa, you can order one there (but it is not free, i guess).
The www.intusoft.com page is a good point to start searching.
Rolf
Got mine a week ago.
And it is great !
Rolf Molitor
Ingenieurbuero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Peder K. Hellegaard [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Mittwoch, 3. April 2002 15:43
Betreff: [PEDA] SV: Tasking software
Neither
/100 of the cycle time (limited steps), what nails the timestep
to the declared maximum. It helped me out in some situations, particularly
in some circuits with positiv feedback (like comparators).
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
use the generic spice model mosfet (mq? !),
a model file (irf840.mdl) with the model parameters for the generic mosfet
model has to be in the library path.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Ian Rozowsky [EMAIL PROTECTED]
An: Protel EDA Forum
for parts from
International Rectifiers. They would be referenced in 'read-only field 3'
as:
file={Model_Path}\IR\parttype.ckt (or .mdl, in a special schematic library
for that kind of parts, as the reference field is read-only and can not be
changed 'on the fly' in the schematic editor).
Rolf
That has nothing to do with circuit simulation.
You were just joking, right ?
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Georg Beckmann [EMAIL PROTECTED]
An: 'Protel EDA Forum' [EMAIL PROTECTED]
Gesendet: Samstag, 29. Juni 2002 14:25
Betreff: [PEDA] AW
. No
new fancy gimmicks please, keep it simple (no least cost calculator).
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Gary Packman [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Dienstag, 2. Juli 2002 10:50
Betreff: Re: [PEDA] AW: SPICE sim
Sounds like you have the Orcad Ports enabled. (Tools/Preferences)
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Jenkins, Charlie [EMAIL PROTECTED]
An: 'PEDA' [EMAIL PROTECTED]
Gesendet: Mittwoch, 3. Juli 2002 15:08
Betreff: [PEDA] Port length
I am using PDFWriter 4.0 and print all documents works fine for me.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Jeff Adolphs [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Dienstag, 16. Juli 2002 17:11
Betreff: Re: [PEDA] pdf output
P99SE/SP6 shows the same behaviour but there you can ignore the error
messages and do the simulation run with positive values even if Protel calls
for negative ones . Do the simulation runs ok in DXP if you ignore the
messages ? Did you already reported the behaviour to Altium ?
Rolf Molitor
I am interested in the other problems you found working with the DXP
simulator. Can you give us some hints ?
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Tim Hutcheson [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Donnerstag, 8
.
It could have been at www.intusoft.com or www.pspice.com (you may have to
register to get into the support area and be aware that PSPICE is no XSPICE
simulator and has some functions of its own).
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Tim Hutcheson
in the protel sim.ddb.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Rolf Molitor [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Mittwoch, 21. August 2002 19:12
Betreff: Re: [PEDA] Simulating with load transfer function
Tim,
what about
the part type as a parameter (%) ?
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Thomas Josefsson [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Freitag, 27. September 2002 03:41
Betreff: Re: [PEDA] Simulation Function Block, PWLR
I
not inserts
the value of the part type instead of '%v', the compiler itself seems to
know how to handle '%%vd').
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Thomas Josefsson [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Sonntag, 29
Thomas,
i tried it with the boolean values TRUE and FALSE for the fraction
parameter and it worked for me.
If fraction is selected TRUE the input_domain parameter has the meaning of
percentage (0.1 means 10%). So the 100 you choose might be a problem too.
Rolf Molitor
Ing.Buero i2e
Remscheid
inserted the
data from the file into the pwl statement, but it doesn't. I once asked
Protel about it but never got any answer. Try contacting Altium once again
on this matter, just to make sure.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Ursprüngliche Nachricht-
Von: Alfonso Baz [EMAIL
problems
(convergence) are spice related and are no P99 issues.
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
-Ursprüngliche Nachricht-
Von: Julian Higginson [EMAIL PROTECTED]
An: 'Protel EDA Forum' [EMAIL PROTECTED]
Gesendet: Dienstag, 12. November 2002 08:33
Betreff: [PEDA] help: basic
No, you are not the only one.
-Ursprüngliche Nachricht-
Von: [EMAIL PROTECTED]
An: Protel EDA Forum [EMAIL PROTECTED]
Gesendet: Freitag, 22. November 2002 11:22
Betreff: Re: [PEDA] position dialog
I keep receiving this message about every 5 minutes. Are others seeing it
as
well (a
The models in the Libraries supplied with the original 99SE CDs have errors,
but in the latest library updates they seem to be ok.
Have also a look at the websites of other simulaton packages for more
transformer/inductor models (e.g. intusoft).
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
Hi,
Tools Preferences Display Layer Drawing Order
Regards
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Urspr 1ngliche Nachricht-
Von: Mr. Zhang Yangtian [EMAIL PROTECTED]
An: Protel?? 3 [EMAIL PROTECTED]
Gesendet: Mittwoch, 8. Oktober 2003 16:48
Betreff: [PEDA] How
Hi Leo,
that behaviour is ok. You can not give teh focus to a component in the pcb
editor like you are used to in the schematic editor.
Regards
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
-Urspr ngliche Nachricht-
Von: Leo Potjewijd [EMAIL PROTECTED]
An: [EMAIL PROTECTED
The 'M' in the designators MQ1 and MQ2 may let the simulator look for a
MOSFET model. But you want the IRF840 to be handled like a subcircuit (as
stated in library field #3). Try changing the designators to Q1 and Q2.
Rolf Molitor
Ing.-Buero i2e
Remscheid / Germany
- Original Message
A quick guess ... change the name of the controlled source EGND. The problem
might be the 'GND' in the name.
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
- Original Message -
From: Mr. Zhang Yangtian [EMAIL PROTECTED]
To: Protel [EMAIL PROTECTED]
Sent: Saturday, January 31, 2004
you select Properties you will see what bitmap file this power object
uses. Just edit the bitmap to change the view of the power object.
Regards
Rolf Molitor
Ing.Buero i2e
Remscheid / Germany
- Original Message -
From: Dennis Saputelli [EMAIL PROTECTED]
To: Protel EDA Forum [EMAIL
.
Rolf Molitor
Ing.Buero i2e
Remscheid/Germany
- Original Message -
From: Leo Potjewijd [EMAIL PROTECTED]
To: Protel EDA Forum [EMAIL PROTECTED]
Cc: Protel EDA Forum [EMAIL PROTECTED]
Sent: Monday, August 02, 2004 10:46 AM
Subject: Re: [PEDA] changing power symbols
At 31-7-2004 13:34
45 matches
Mail list logo
