Hi, I want use 4mil clearance under 1mm pitch BGA for (BGA SMD Pads, traces, TH pads and VIAs), same time I want use 7mil clearance outside BGA for (all primitives on board -> traces, VIAs, PADs...), how to set Clearance Constraints?
Here is copy of Clearance.RUL file RuleKind=Clearance|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Count=1| Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=Board|S cope2_0_Value=Board|Name=KOKO_LEVY|Enabled=TRUE|CommentLength=1|Comment=|Gap =7mil? RuleKind=Clearance|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Count=1| Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=Footpri nt|Scope2_0_Value=SHORT_CLOSED|Name=SHORT|Enabled=TRUE|CommentLength=1|Comme nt=|Gap=0.004mil? RuleKind=Clearance|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Count=1| Scope1_0_Kind=NetClass|Scope1_0_Value=All Nets|Scope2Count=1|Scope2_0_Kind=PadSpec|Scope2_0_Value=1#1#0#1#1#1#0#0#0#0# 0#0#TOP#0#No Net#18#18#Round#60#60#Round#60#60#Round|Name=SMD-PAD_18-PIIRIN_ALLA|Enabled= TRUE|CommentLength=1|Comment=|Gap=4mil? RuleKind=Clearance|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Count=1| Scope1_0_Kind=NetClass|Scope1_0_Value=All Nets|Scope2Count=1|Scope2_0_Kind=ViaSpec|Scope2_0_Value=1#1#1#1#0#TOP#BOTTOM #8#16#No Net|Name=VIA_16/8-PIIRIN_ALLA|Enabled=TRUE|CommentLength=1|Comment=|Gap=4mil ? RuleKind=Width|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Count=1|Scop e1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=Board|Scope 2_0_Value=Board|Name=Width|Enabled=TRUE|CommentLength=1|Comment=|MaxLimit=60 mil|MinLimit=4mil|PreferedWidth=6mil? RuleKind=RoutingTopology|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Co unt=1|Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=B oard|Scope2_0_Value=Board|Name=RoutingTopology|Enabled=TRUE|CommentLength=0| Comment= |Topology=Shortest? RuleKind=RoutingPriority|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Co unt=1|Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=B oard|Scope2_0_Value=Board|Name=RoutingPriority|Enabled=TRUE|CommentLength=0| Comment= |Priority=0? RuleKind=RoutingLayers|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Coun t=1|Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=Boa rd|Scope2_0_Value=Board|Name=RoutingLayers|Enabled=TRUE|CommentLength=0|Comm ent= |Top Layer=Horizontal|Mid Layer 1=Not Used|Mid Layer 2=Not Used|Mid Layer 3=Not Used|Mid Layer 4=Not Used|Mid Layer 5=Not Used|Mid Layer 6=Not Used|Mid Layer 7=Not Used|Mid Layer 8=Not Used|Mid Layer 9=Not Used|Mid Layer 10=Not Used|Mid Layer 11=Not Used|Mid Layer 12=Not Used|Mid Layer 13=Not Used|Mid Layer 14=Not Used|Mid Layer 15=Not Used|Mid Layer 16=Not Used|Mid Layer 17=Not Used|Mid Layer 18=Not Used|Mid Layer 19=Not Used|Mid Layer 20=Not Used|Mid Layer 21=Not Used|Mid Layer 22=Not Used|Mid Layer 23=Not Used|Mid Layer 24=Not Used|Mid Layer 25=Not Used|Mid Layer 26=Not Used|Mid Layer 27=Not Used|Mid Layer 28=Not Used|Mid Layer 29=Not Used|Mid Layer 30=Not Used|Bottom Layer=Vertical? RuleKind=RoutingCorners|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Cou nt=1|Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=Bo ard|Scope2_0_Value=Board|Name=RoutingCorners|Enabled=TRUE|CommentLength=0|Co mment= |CornerStyle=45-Degree|MinSetBack=100mil|MaxSetBack=100mil? RuleKind=RoutingVias|NetScope=DifferentNets|LayerKind=SameLayer|Scope1Count= 1|Scope1_0_Kind=Board|Scope1_0_Value=Board|Scope2Count=1|Scope2_0_Kind=Board |Scope2_0_Value=Board|Name=RoutingVias|Enabled=TRUE|CommentLength=1|Comment= |HoleWidth=8mil|Width=16mil|ViaStyle=Through Hole|MinHoleWidth=8mil|MinWidth=16mil|MaxHoleWidth=28mil|MaxWidth=50mil? Sincerely, Juha Pajunen, Hw Engineer Bitboys Oy E-mail: [EMAIL PROTECTED] ------------ NOTE: This message, and any attached files, may contain privileged or confidential information. It is intended for use only by the designated recipients. Any disclosure, copying or distribution of, or reliance upon, this message by anyone else is strictly prohibited. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To leave this list visit: * http://www.techservinc.com/protelusers/leave.html * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * Forum Guidelines Rules: * http://www.techservinc.com/protelusers/forumrules.html * * Browse or Search previous postings: * http://www.mail-archive.com/proteledaforum@techservinc.com * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *