So far, no response to this. Can anyone say definitively if a Spectra with
a v1.x MLM will scan or not?
The guy is coming tomorrow for some programming.
Thanks,
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of N9WYS
For everyone on the list - with some offline
Hehehehehe.. TNX anyway, Kris. ;-)
73 es Cheers!
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Kris Kirby
On Wed, 3 Feb 2010, N9WYS wrote:
So far, no response to this? Can anyone say definitively if a Spectra
with a v1.x MLM will scan
this for him?
73 de Mark - N9WYS
a different scan for the Zone I
select.
Hope this helps.
David
From: Repeater-Builder@yahoogroups.com On Behalf Of Kris Kirby
On Sat, 30 Jan 2010, N9WYS wrote:
I am trying to program my 900 MHz Spectra for SCAN. This radio is
modified for Conventional/Zones/MPL (with 120 modes). When
Conv_OpSel_Scan = ENABLED
56NonPri_Mode_Slaved_Scan = ENABLED
57Pri_Mode_Slaved_Scan= ENABLED
What do I need to turn on in the MOFLAGS to get this to scan??
Thanks,
Mark - N9WYS
Greg,
Have you disabled the internal controller?
It needs to be completely disconnected and some wires jumpered before the
external controller will work as designed...
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com
Dave,
This is your best resource for information regarding your inquiry:
http://www.repeater-builder.com/motorola/r100/r100-index.html
Mark N9WYS
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of Dave Hubbell
Whats involved in making
it
altogether so far this way... YMMV.
Good luck, all - and happy surfing.
73 de Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of JG
Tnx Skipp !!
You've saved my bacon.
I have since loaded Adblock Plus
Last time I needed them, I bought them from Motorola themselves. still
available, but certainly not cheap!
_
From: Repeater-Builder@yahoogroups.com On Behalf Of kh6...@netscape.net
Does anyone have a source for these capacitors,
Which are used in Motorola Micor power supplies?
Agreed, Eric... but being affiliated with public safety, I also see that
some agencies (mostly municipalities with limited budgets) are waiting as
long as possible before being forced to bite the bullet.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf
Albert,
This depends on the service. Public Safety and Business Radio services are
affected. Amateur Radio and GMRS are not - at this time. (IIRC)
I would certainly expect to see a glut of non-narrowband compatible
equipment enter the surplus market soon...
Mark - N9WYS
-Original
Allan,
First off, if it is being used as a desktop station radio (i.e., NOT duplex)
the first thing that you will find is you need to add another radio chassis
to be able to convert it into a repeater - the DeskTrac repeater used
separate chassis (plural) for TX and RX.
Mark - N9WYS
- N9WYS
_
From: Repeater-Builder@yahoogroups.com On Behalf Of kd6aaj
70% Isopropanol Alcohal is my favorite cleaner. Make sure all power is off
to the radio, and give it a few minutes to evaporate before restoring power.
73,
KD6AAJ
--- On Tue, 7/28/09, Michael Ryan mryan
Welcome Andy! Hope you have success in finding a new home for GB3CC.
73 de Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of Andy Hearn
Sent: Thursday, July 16, 2009 10:47 AM
To: Repeater-Builder@yahoogroups.com
out for John Holland... we communicated a couple of
months back regarding some Newbridge MainStreet 3624 units I am trying to
program.
John, Can you reach out for me via private email again? You email is
bouncing.
Thanks to the moderators for the bandwidth.
Mark - N9WYS
n9wys (at) ameritech (dot
Doesn't that (squelch tail without reverse burst) already occur? If so,
I'm not particularly worried about it.
Mark - N9WYS
_
From: Repeater-Builder@yahoogroups.com On Behalf Of James Delancy
PL only squelch will work solely on the PL detect function of the station.
This means
for AND squelch, but have been
told that PL-only squelch may be a bit more forgiving. I just haven't had
an opportunity to get to the tower and change the setting to see for myself
whether this is true.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Adam Feuer
Don't you remember?? He promised you CHANGE...
That is to the RIGHT of the decimal. ;-p
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Jeff DePolo
What didn't go way up?
The number of digits to the left of the decimal point in my checking
to get to playing around will all the new goodies!
73 all!
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of skipp025
Sent: Saturday, May 16, 2009 10:46 PM
To: Repeater-Builder@yahoogroups.com
Subject: [Repeater
Exactly, Paul. ;-)
I picked up a 220V heater for my garage for $50... The guy wanted $85 and I
told him he'd be dragging it home after the rains on Saturday. (I bought it
Friday when they were predicting rain all day for Saturday.)
Got some other stuff I needed/wanted too.
Mark - N9WYS
What's that?? I
know... a user's manual would be nice, but none available that I can find
for download.
Thanks!
Mark - N9WYS
Nope - Magnuson Hotel in Dayton... right off I-75 just south of I-70. LOTS
of little problems, and management was less that helpful.
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of nj902
--- In Repeater-Builder@yahoogroups.com, N9WYS n9...@... wrote:
I left
to program them... even though they
are close to being a GTX. Close, but no cigar. ;-)
Thanks all!!
Mark - N9WYS
and busy, but I hope
you are catching up on the thread…
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Gran Clark
Bob
Astron 35A supplies and probably other sizes are sensitive to the SCR
triggering. One of the causes I found was due to a shift in the initial
Thanks to all who have offered suggestions - however sarcastic - about
remedying this situation. They all merit consideration, and I will certainly
do so... and will post my results!
73 de Mark - N9WYS
a hardened power supply, that could
remedy my situation?
Thanks,
Mark - N9WYS
order... to eliminate any RF issues.
I do access to a 120A switcher that I may try and see what happens.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com [mailto:[EMAIL PROTECTED] On Behalf Of
Bob M.
Sent: Monday, December 08, 2008 9:54 AM
To: Repeater-Builder
Will do, Bob. Thanks!
73 de Mark - N9WYS
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED]
Sent: Monday, December 08, 2008 12:04 PM
To: Repeater-Builder@yahoogroups.com
Subject: Re: [Repeater-Builder] Astron P/S question
Hi Mark,
Bypass
Brian,
Why would you think you can't use an amp (or higher power) on 900 MHz as an
Amateur? My repeater station is 150W, with added gain via the antenna
system; my mobiles are 12W (but there are 35W units available), and my HT's
are 4W units...
Mark - N9WYS
N9WYS/R 927.5250 (PL 151.4) Joliet
connection) and
are coming down in price.
Do your research (including asking the collective knowledge base here, as
you have) and then make your informed decision as to what to buy. Good
luck!
73 de Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL
is offered.
All items are located in the Southwest suburban Chicago area (Joliet), so
pick up is probably more of a viable option than shipping.
If you are interested, contact me off-list at: n9wys (at) ameritech
(dot) net and I will attempt to answer any questions you may have.
Mark
John,
That (GMRS License) would be a bit difficult for Mattos – he’s in Brazil…
Mark – N9WYS
From: Repeater-Builder@yahoogroups.com [mailto:[EMAIL PROTECTED] On Behalf Of
Maire-Radios
Sent: Saturday, November 15, 2008 2:57 AM
To: Repeater-Builder@yahoogroups.com
Subject: Re: [Repeater
I wonder if they are metric rather than standard sized u-bolts? This might
account for the difference in size...
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Chuck Kelsey
The application is a small side-arm bracket. I made it from aluminum square
reply off-list to n9wys (at) ameritech
(dot) net.
Thanks,
Mark - N9WYS / WQIV271
Mike,
Did you try contacting Ted at MDM Radio? His slogan is, If it's in stock,
we've got it. Hehehehe
Have him check his stock - I just got one from him for 141.3. And he's a
lurker here, so he may have already reached out for you off-list. ;-)
73 de Mark - N9WYS
From
Yes it is, George.
Mark - WQIV271/N9WYS (LAG 1970)
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of George Henry
Is that affiliated with the LAG (Lakes Area GMRS) Group, Mark?
George, KA3HSW / WQGJ413
LAG 951
- Original Message -
From: n9wys [EMAIL
to reconstruct
and understand the operation of the station well enough to troubleshoot most
of the issues and then tune-up the station myself. FWIW - photos are posted
at the R-B Groups site, in a photo album labeled N9WYS Repeaters.
Mark - N9WYS/WQIV271
-Original Message-
From: Repeater
The new Joliet East GMRS repeater is ON-THE-AIR!
462.5500 PL 156.7
Thanks to everyone who assisted me with this project - whether it was with
hardware, technical or moral support. ;-)
Mark - WQIV271 / N9WYS
John,
It utilizes a standard 5 MHz offset. Located in Joliet, IL.
This is that Unified Chassis MICOR Community Repeater I've been battling
with for the past few months. (Photos are posted at the R-B Yahoogroup
site.)
Mark - N9WYS/WQIV271
From: Repeater-Builder@yahoogroups.com
Mike,
Are there any other markings on the cable? Specifically, I'd be looking for
the following:
FSJ1-50A
This is 1/4 Superflex - about the same size as RG-8X...
Velocity factor for this (FSJ1-50A) cable is 84%
http://awapps.commscope.com/catalog/product_details.aspx?id=1342
Mark - N9WYS
No problem on the link, Mike. Glad it as the same stuff!
A 1/4-wave cable on an open circuit introduces a short... If I remember
correctly (and I'm sure if I'm wrong others will correct me!) you need a
1/2-wave cable between cans.
Mark - N9WYS
-Original Message-
From: Repeater-Builder
.
It's playing just like mother M designed it to!!!
Thanks to everyone who helped with this project, whether it was with
hardware, schematics, suggestions or moral support. The machine should be
on-the-air within the next two weeks.
73 de Mark - N9WYS / WQIV271
...
NOTE: I have no pecuniary interest in his business - just answering an
inquiry regarding a source for dummy loads.
73,
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of [EMAIL PROTECTED]
John,
Very well then, I guess I need to be shopping for a good load
.
So, I ask again - if ANYONE has a TRN6165A Master Decoder card they are not
using and would like to put to good use, PLEASE CONTACT ME.
Mark - N9WYS
for the cards I
have. Until I can confirm something (one way or another) I'm at an impasse.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Eric Lemmon
Mark,
Now, I'm the one who is confused! I just looked at a UHF community repeater
and noticed
off. What's a good
time to try to call? (Remember the 2-hour time difference... wink )
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Joe Burkleo
Mark,
Sorry to hear that you are still fighting this problem.
I think we were on the right track when
Thanks Gerald!!
I think that'll get me headed in the right direction... Yes, if you can get
a clean copy of the schematic (maybe have someone scan it and send it to me
via e-mail??) that'll help **immensely**!
73 de Mark - N9WYS
-Original Message-
From: Repeater-Builder
- N9WYS / WQIV271
-Copied Thread-
From: Repeater-Builder@yahoogroups.com On Behalf Of n9wys
Sent: Monday, August 11, 2008 11:26 AM
More information about this project.
I have the station working - receiving, decoding proper PL tone, repeating,
transmitting audio, etc. The only thing
.
For the time being, I am going to put the machine on the air as-is. it works
just fine, other than it will have to be CSQ receive for all users. I'll
decide later on whether I will put in a tone panel, or continue to operate
it as it is now.
Mark - N9WYS / WQIV271
Nate - I still remember the album sleeve for the Rolling Stones' Let It
Bleed album...
Lower right corner: THIS RECORD SHOULD BE PLAYED LOUD
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Nate Duehr
Bob M. wrote:
He was into the hard rock stuff
Thanks, Givan!
That’s the info I was looking for – now knowing that, I’m hoping that the CP200
CPS will program them…
Mark – N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Givan George
Mark,
The EP450 is the equivalent of the Motorola CP200 or so. It is programmed
Just did. thanks for reminding me, Darrell.
From: Repeater-Builder@yahoogroups.com On Behalf Of jistabout
Mark, you might try asking on the Batlabs forum:
http://batboard.batlabs.com
- Darrell/KA7BTV
) and the
cost was well over $100.
Hi-fi??? C'mon - you're dating the entire group now! hehehehe Some of
the younger whippersnappers here probably don't even know what a hi-fi is,
or an album for that... OK, I think I'll sulk off to the old folks home
now. (AKA: Casino) ;-p
Mark - N9WYS
in the
Amateur bands this is not an issue. Any suggestions and assistance are
appreciated.
Mark - N9WYS
experience, but then again - there are 9 ITECS trailers statewide
and they ALL are experiencing the same issues we did.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of tgundo2003
Sent: Wednesday, September 10, 2008 12:10 PM
My sincerest apologies to the group. This was supposed to go PRIVATE
e-mail, and obviously did not.
Again, my apologies for the language used within.
-Original Message-
From: n9wys
OFF-LIST REPLY
Tom,
We had EFJ repeaters (VHF, UHF and 800) in the ITECS trailer...
--- snip ---
- N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of n9lv
That is what I thought was wrong first of all, tried it both ways and
no change either way. I thought for sure when I wired up the
controller that it was fine, but not sure when the other repeater
came
You're correct Greg... that's exactly what it is doing. It gets the tone
from the Four User Control Module, then the Master Decoder passes THAT to
the exciter. My bad for not explaining it correctly.
Mark - N9WYS
-Original Message-
From: [EMAIL PROTECTED] On Behalf Of Greg Forrest
Anyone have (perchance) a copy of LBI38377 - Operator's Manual for the M-PA
portable? I was just given one (a UHF Systems radio) and have I no info on
it at all.
Thanks,
Mark - N9WYS
beep during
MDC) enabled for the dog catchers, etc.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Mike Morris WA6ILQ
Sent: Wednesday, August 27, 2008 2:42 AM
To: Repeater-Builder@yahoogroups.com
Subject: Re: [Repeater-Builder] Re: Trunking Features w/o
digitized
audio and it makes my hair stand on end.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of skipp025
Sent: Wednesday, August 27, 2008 10:57 AM
To: Repeater-Builder@yahoogroups.com
Subject: [Repeater-Builder] Re: Trunking Features w/o Trunking?
wd8chl
conductivity not listed)
3M 1170 (listed: conductive adhesive)
Although I'm thinking at these costs, they must ALL have conductive
adhesives... 425 (1 wide) costs $20.93/roll; 427 is $61.95/roll; and 1170
is $46.07. If anybody has insights, I'd be interested to hear!
Thanks,
Mark - N9WYS
in
radio cabinet rails.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of no6b
At 8/22/2008 23:50, you wrote:
The clips are called tinerman clips and I have found them at auto parts
stores but I think they are a little spendey.
The ones that are threaded
OK, let's all open our hymnals to page 85 and sing, What a friend we have
in 3M.
;-)
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Cort Buffington
Note the common thread here. Almost everyone has 3M 33+ in their recipe. As
religious arguments go -- it looks
C74MSY-3101BY or
similar - the BY is the key here, I think.) I have seen a older
MSY-series station on eBay with this card in the chassis, so hopefully
someone out there has the manual for it.
I *REALLY* need this schematic to get my repeater going...
Thanks,
Mark - N9WYS / WQIV271
, your efforts are greatly appreciated!
Mark - N9WYS
This module schematic may also be in a MOTRAC manual, if that helps anyone
in locating this module for me. (I have found the module installed in a
MOTRAC repeater.)
Thanks,
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Mark
Before the list hiatus, I was attempting
for the Buy It Now, or
what the reserve amount is. But it hasn't been met yet.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of [EMAIL PROTECTED]
Hello RBites
I think I posted this previously, but still lloking for a 222 MHz bandpass
the tone out on Pin 2.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of godofrepeaters
Are you sure you have the encode board plugged in with a reed plugged in?
--- In Repeater-Builder@yahoogroups.com, n9wys [EMAIL PROTECTED] wrote:
More information about
in my possession so I can troubleshoot further.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of sgreact47
A community repeater has NO PL Encoder..
The PL from the receiver is decoded and the PL tone is low pass
filtered and passed to the transmitter PL
if a required jumper
is missing or a jumper is improperly installed on my Master Control card.
Thanks!
Mark - N9WYS
I acquired a pair of EF Johnson Viking CK 8571 (intrinsically safe) series
portable radios. These are in the 900 MHz band, and I'd like to try to
convert them to ham use - unless this would be an exercise in futility.
The manual was available online, and after some reading I see that Johnson
Don,
I'd think it's broadbanded enough to be able to work well at 444. The
antenna I have on my 444.5500 repeater (although supposedly tuned to the
ham band) is actually a 450 - 470 MHz, 4-bay dipole itself. and it does VERY
well, even with the modified phasing harness.
Mark - N9WYS
Mark N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Bill Hudson
Paul Plack - Please site the law that forbids felons from having ham radio
licenses. You act like you speak with authority - I'd like you to
demonstrate it for me please.
Bill - W6CBS
_
From
It just doesn't know the words ;-p
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Bill
Howdy group.
I have a Motorola MSR2000 repeater on the ham bands that I maintain.
VHF 147.32 in Austin (Oak Hill)Texas.
It has developed a hum on the receive
you will know the
duplexer is tuned properly and working on-frequency when you receive it.
(He even supplied me with analyzer plots showing rejection, insertion loss,
etc.)
My 2¢ worth...
73 de Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Don Spivey
Thanks Bill - will most certainly do this!
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of [EMAIL PROTECTED]
Check the repeater-builder site for a mod to the station control module to
make it DISABLE the transmitter and add a status LED as well.
Bill - WA0CBW
... It seems that this Community
Repeater works differently than the regular MICOR station, so I'm still
feeling my way along with it.
Thanks for all the help and support!
Still chugging along...
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Eric Lemmon
that it is working in the way
it is supposed to be configured, next thing to do is chase down the audio
path.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Joe Burkleo
Mark,
I think you have a good idea about starting fresh with an unaltered
board.
That would
for each of the cards.
4) The repeater keys only in PL mode now...
At this stage I'm not sure whether you're right or wrong, Joe. But at least
it's alive - if only at 50%. ;-)
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Joe Burkleo
Mark,
OK, now
Well, the MICOR Community Repeater manual supplement arrived today, and I've
been going through it with the proverbial fine-toothed comb.
I replaced most of the jumpers I originally removed from the backplane.
(According to the jumper matrix in the CR manual, they needed to be IN
whereas the
what you have. I've got to
be missing something somewhere.
(Kevin, you still haven't commented yet...)
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Joe Burkleo
Mark,
Sorry to hear you are still having problems. The Micor series of
radios were made
all the
modules I have - I know it doesn't cover the 4-User Control Module, and
maybe not the Master Decoder either... I have several versions of the
Station Control, Squelch Gate and Time Out Timer modules - some schematics
for the newer revisions are not shown in the manual either.
Mark - N9WYS
about the Line Driver, Squelch Gate and/or Station
Control Module cards jumpers?
Any ideas? (Kevin, you're the MICOR guru...)
Thanks,
Mark - N9WYS
all this resolved.
I'll double check the card edges to make sure the pin seats are tight. I
have an extender card to work with, too, so I think that'll help.
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Com/Rad Inc
Sent: Sunday, July 27, 2008 10
now, I can only disable ONE
of the tones - the others decode and the repeater keys whether the switch is
on or off.
I'll check for the other mods you speak of.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Joe Burkleo
Mark,
It sounds like you may
...
And to top it all off, they are all listed as follows: * Item has been
cancelled. :-(
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Gary Glaenzer
Mark;
You need the supplemental manual that covers the community
repeater..68-81XXXE25 is the number if memory
Well, that got me 6 responses, but nothing like what I need. or maybe. The
one that MIGHT be what I need reads: MAN INSTR FASC SUPPLEMENT It is item #
6881074C55
But I'm only guessing at this stage.
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Gary Glaenzer
believe I have the other two manuals at home, but I'll double check the
numbers when I get home this afternoon.
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Eric Lemmon
Mark,
If you're not going to use your repeater as a community repeater, then you
, these are the manuals I currently have:
Control and Applications Manuals: 68P81025E60-E and 68P81025E60-F
MICOR Base and Repeater Stations Manuals: 68P81025E50-G (12W to 75W
stations) and 68P81039E55-A (200W and 225W stations)
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
FOUR USER CONTORL MODULE \
FOUR USER CONTORL MODULE \
FOUR USER CONTORL MODULE Yes, 4 slots labeled the same
FOUR USER CONTORL MODULE /
DIODE LOGIC
MULTI PL ENCODER
MULTI DLP ENCODER
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED
. Hopefully when it gets here I'll have one of those
Ah-HAH! moments... ;-)
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of Joe Burkleo
Mark,
I think Eric is correct in that you have got a community repeater
chassis. These can be a handful to get
And a Business Band license fee is $105 for a 10-year license - not
including the coordinator's fees.
http://mymotorolaradio.com/fcc.asp
Mark - N9WYS / WQIV271
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of wd8chl
George Henry wrote:
There ARE frequency
The only fly in the ointment is moving the RX. We don’t know WHERE this noise
is coming from... so if he moves, he may move CLOSER to rather than further
away from the source...
I think a 904 notch on the RX may be a workable solution.
Thanks, Ron.
Mark - N9WYS
-Original Message
Hi Ron, and thanks for the reply.
First off, the 904 signal is always there - and about 100kHz wide... A
WIDE signal.
Second, his machine is on 927.600/902.600.
As you can see, the signal is 2 MHz up and still clobbering his receiver.
Mark - N9WYS
-Original Message-
From: Repeater
of the nut you're
trying to remove.
Did the same for an oil pump drive when I rebuilt the engine in my car a few
years ago. to prime the oiling system.
Mark - N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of Thomas Oliver
I have a yaesu FT-60 handheld that has a noisy volume pot
/NoiseStuff.html
This article describes the design I am familiar with:
http://mrtmag.com/mag/radio_rf_samplers_directional/
If you have a Bird wattmeter, you can construct one for use with your meter:
http://www.repeater-builder.com/projects/bird43sampler.html
Hope this helps!
Mark - N9WYS
- N9WYS
From: Repeater-Builder@yahoogroups.com On Behalf Of de W5DK
Using a Mike quote doesn't anybody read the site?!!!
http://www.repeater-builder.com/projects/bird43sampler.html
sorry John could resist J
and Ron's description / answer was correct.
73
Don W5DK
From: Repeater
for the transmitter and Micor receivers/SpectraTAC voter network. That
repeater works like a champ!
Now on the other hand, I'm running an MSF5000 on 900 MHz and *it's* working
like a trooper!!
Mark - N9WYS
-Original Message-
From: N0ATH [EMAIL PROTECTED]
Date: 2008/07/08 Tue PM 03:48:35 EDT
Replied off-list
Mark - N9WYS
-Original Message-
From: Repeater-Builder@yahoogroups.com On Behalf Of n9ex_jack
Sent: Thursday, July 03, 2008 6:29 PM
To: Repeater-Builder@yahoogroups.com
Subject: [Repeater-Builder] TKR 820
Hi Guys
does anyone out there happen to have a pinout
1 - 100 of 471 matches
Mail list logo