Here are some specifics on the shaper error. When I reach the end of
the wizard, I get the following text at the top of the screen:
block in log quick on ng0 proto udp from any port = 67 to
192.168.100.0/24 port = 68 label allow dhcp client out wan Warning:
Cannot modify header information -
I have two machines set up with 0.93.2, each with 3 NICS, OPT is bridged to
WAN and handles a small DMZ. CARP synchronization happens on the LAN
interface.
I configured CARP failover as per the tutorial and found that while the
rules and configuration changes are synching properly, the backup
When attempting to add a cache administrator email address the following
error gets puked out:
Warning: fopen(/usr/local/etc/squid/advanced/acls/src_subnets.acl): failed
to open stream: No such file or directory in /usr/local/pkg/squid_ng.inc on
line 487 Warning: fwrite(): supplied argument is
My present experience with carp and bridging did not go well 1 GB of
multicast traffic in under 5 minutes.
All considered I was using vlans so maybe that was my trouble
-Original Message-
From: Gary Buckmaster [mailto:[EMAIL PROTECTED]
Sent: Thursday, November 17, 2005 4:43 PM
To:
No proxy arp is configured, although as I said, OPT1 is bridged to WAN,
which you indicated is a very big bad idea. I'm guessing then, that I
cannot set up a bridged firewall with failover?
-Original Message-
From: Scott Ullrich [mailto:[EMAIL PROTECTED]
Sent: Thursday, November 17, 2005
No, bridged firewalls + failover does not work.
On 11/17/05, Gary Buckmaster [EMAIL PROTECTED] wrote:
No proxy arp is configured, although as I said, OPT1 is bridged to WAN,
which you indicated is a very big bad idea. I'm guessing then, that I
cannot set up a bridged firewall with failover?
No, bridged firewalls + failover does not work.
are there plans to make it work?
thanks,
-randall
--
:// randall s. ehren :// voice 805.893.5632
:// systems administrator:// isber|survey|avss.ucsb.edu
:// institute for social, behavioral, and economic
Not at this time. Patches accepted, however.
On 11/17/05, randall ehren [EMAIL PROTECTED] wrote:
No, bridged firewalls + failover does not work.
are there plans to make it work?
thanks,
-randall
--
:// randall s. ehren :// voice 805.893.5632
:// systems
It would be helpful to understand what's causing the issue here. I'd really
like to see about making this work, but a pointer in the right direction
would be good.
-Original Message-
From: Scott Ullrich [mailto:[EMAIL PROTECTED]
Sent: Thursday, November 17, 2005 1:13 PM
To:
http://www.monkey.org/openbsd/archive/tech/0407/msg00102.html
http://www.seattlecentral.edu/~dmartin/docs/bridge.html
On 11/17/05, Gary Buckmaster [EMAIL PROTECTED] wrote:
It would be helpful to understand what's causing the issue here. I'd really
like to see about making this work, but a
I was under the impression that altq has support for vlans. Is
this enabled in pfsense at the moment.
Have tried a couple of time but get unsupported interfaces. I
know that my fxp and sis cards support it
So I guess it must be the vlans that are the issue
On Thu, 17 Nov 2005, alan walters wrote:
I was under the impression that altq has support for vlans. Is this
enabled in pfsense at the moment.
Have tried a couple of time but get unsupported interfaces. I know that
my fxp and sis cards support it
So I guess it must be the vlans that are
Tried on 0.90 through to non released 0.93.2
With the same troubles.
I have vlans on both of the pfsense wan and lan interfaces.
Might try again tomorrow. To see if I can isolate it a bit
On Thu, 17 Nov 2005, alan walters wrote:
I was under the impression that altq has support for vlans. Is
Does anyone have IPSec tunnels auto establish working?
I can only seem to get the tunnels to come up when traffic is passing over
them.
Also wondering if there is anything special that needs to be
done to do traffic shapping through an IPSec tunnel?
Thanks
John
At 06:04 PM 11/17/2005, you wrote:
Tried on 0.90 through to non released 0.93.2
With the same troubles.
I have vlans on both of the pfsense wan and lan interfaces.
Might try again tomorrow. To see if I can isolate it a bit
Hmm, I remember an issue where the vlans didn't have a bandwidth, so
15 matches
Mail list logo