Hi,
I'm experiencing another issue. I'm trying to create a bootable micro sd
> card. I was able to get it to work on one of my elphels (the older one that
> doesn't work without a card). However it's not working with the other 3
> newer elphels. They just boot using NAND memory. I filed off the
Mohamed,
It may be that the corner is not cut off enough (mechanical switch is still
engaged) or the card does not have a resistor on D3. When selecting the card we
X-rayed multiple brands - many cards have active components in that area and do
not survive cutting the corner off. Does it still
Hi Oleg,
I'm experiencing another issue. I'm trying to create a bootable micro sd
card. I was able to get it to work on one of my elphels (the older one that
doesn't work without a card). However it's not working with the other 3
newer elphels. They just boot using NAND memory. I filed off the
That worked. Thanks
On Thu, Feb 22, 2018 at 1:04 PM, Oleg
wrote:
> You don't have to close minicom.
>
> It works with the card, right? Then:
>
> 1. If the board is one of the first we sent you (what's the serial
> number?) then... later we had to make a minor
You don't have to close minicom.
It works with the card, right? Then:
1. If the board is one of the first we sent you (what's the serial number?)
then... later we had to make a minor fix. The problem was it wouldn't boot
from flash without a card.
Try: if you have some other micro sd card at
>
> No it doesn't print anything at all. I can't connect via ssh. Is it
> possible the baud rate isn't 115200?
No.
Any network leds blinking? Or at least light up temporarily?
Is the board getting warm?
Do you power with the power supply board (TRACO)? Is it the same you used
for the 1st board?
Hi,
Is it printing anything when you power on?
Can you connect to the camera via ssh?
Oleg
On Thu, Feb 22, 2018 at 7:38 AM, Mohamed Morsy wrote:
> Hello Oleg,
>
> I was able to fix one of my elphels yesterday using the methods you
> suggested. Now I'm trying to do the same
The 2 leds (green and yellow) are on. I'm using power from a battery
without the traco board. This is what I did with the 1st board. I also have
the traco board if i need it which is 18-75V. I haven't changed anything in
minicom. I just flashed with the recovery card in, removed it, and tried to
No it doesn't print anything at all. I can't connect via ssh. Is it
possible the baud rate isn't 115200?
On Thu, Feb 22, 2018 at 11:35 AM, Oleg
wrote:
> Hi,
>
> Is it printing anything when you power on?
> Can you connect to the camera via ssh?
>
> Oleg
>
> On
Hello Oleg,
I was able to fix one of my elphels yesterday using the methods you
suggested. Now I'm trying to do the same with my other one but when I open
the minicom console I can't type anything. Do you have any idea how to fix
this?
Thanks,
Mohamed
On Wed, Feb 21, 2018 at 4:06 PM, Mohamed
Thank you very much
On Wed, Feb 21, 2018 at 3:53 PM, Oleg
wrote:
> Alright. Since you're modifying files on flash rootfs, don't forget to run:
>
>> root@elphel393:~# overlay_sync 1
>> root@elphel393:~# shutdown -hP now
>
>
>
> On Wed, Feb 21, 2018 at 1:50 PM,
Alright. Since you're modifying files on flash rootfs, don't forget to run:
> root@elphel393:~# overlay_sync 1
> root@elphel393:~# shutdown -hP now
On Wed, Feb 21, 2018 at 1:50 PM, Mohamed Morsy wrote:
> actually i think i found my answer.
>
> Thanks!
>
> On Wed, Feb 21,
It's 'root'
On Wed, Feb 21, 2018 at 1:32 PM, Mohamed Morsy wrote:
> It's asking for a login and password. I know the password is pass but what
> is the login?
>
> On Wed, Feb 21, 2018 at 3:12 PM, Oleg
> wrote:
>
>> Get the serial console up
ok so the ip was 192.168.0.9. I changed it and it works. But when i power
it off and restart it, it goes back to 192.168.0.9. Do i have to save it
somehow?
On Wed, Feb 21, 2018 at 3:35 PM, Oleg
wrote:
> It's 'root'
>
> On Wed, Feb 21, 2018 at 1:32 PM, Mohamed
actually i think i found my answer.
Thanks!
On Wed, Feb 21, 2018 at 3:44 PM, Mohamed Morsy wrote:
> ok so the ip was 192.168.0.9. I changed it and it works. But when i power
> it off and restart it, it goes back to 192.168.0.9. Do i have to save it
> somehow?
>
> On Wed,
Hello Oleg,
I was having some difficulties with my linux computer so I hold off on
this. I followed your instructions and I increased the php upload limit and
I was able to upload rootfs. I'm still having some issues. Here's what I've
done:
1. Put recovery card in elphel
2. Went to
Get the serial console up and type:
> root@elphel393:~# ifconfig
On Wed, Feb 21, 2018 at 1:08 PM, Mohamed Morsy wrote:
> Is it possible the ip address of the elphel changed. If so, how do i find
> it?
>
> -Mohamed
>
> On Wed, Feb 21, 2018 at 1:52 PM, Mohamed Morsy
I have not used the mircro usb port. The default ip address has been
changed to 10.4.1.4.
-Mohamed
On Wed, Feb 21, 2018 at 1:34 PM, Oleg
wrote:
> Hi Mohamed,
>
> 10.4.1.4 is that elphel's ip.
>> Do you know how to resolve this issue?
>
>
> The default IP is
Is it possible the ip address of the elphel changed. If so, how do i find
it?
-Mohamed
On Wed, Feb 21, 2018 at 1:52 PM, Mohamed Morsy wrote:
> I have not used the mircro usb port. The default ip address has been
> changed to 10.4.1.4.
>
> -Mohamed
>
> On Wed, Feb 21, 2018
Hi Mohamed,
10.4.1.4 is that elphel's ip.
> Do you know how to resolve this issue?
The default IP is 192.168.0.9
On the 10393 there's a micro USB port - this is serial console:
> https://wiki.elphel.com/wiki/Tmp_manual > *serial console access*.
Do you use it? See any bootlog when power on?
Hi Mohamed,
> However, I'm still having the same problem. On one of my elphels, when I
> use the recovery card it works fine but when I remove the card the feed is
> very laggy. Do you know what the issue is?
It's hard to say without seeing the actual bootlog. If you boot from
recovery card,
Hi Oleg,
Thank you for your help. However, I'm still having the same problem. On one
of my elphels, when I use the recovery card it works fine but when I remove
the card the feed is very laggy. Do you know what the issue is? Also, when
I uploaded the files to ipaddress/update_software.html the
Hi,
I have 2 Elphel 393 boards and I believe both of their internal flash are
> corrupt or old. I am trying to update them. Do you have a link for the
> files or any instructions on how to do so?
>
Before updating:
How are you trying to update them? What image do you use?
Update instructions:
23 matches
Mail list logo