nd 1220-1840mV(20mV*31 step),
they want to say dcdc3's 1650-1840mV range is something strange.
AXP313A datasheet clearly says that dcdc3 is 0.5-1.2V and 1.22-1.84V.
https://github.com/mangopi-sbc/aw-doc/blob/main/pmic/AXP313A_Datasheet_V1.0_cn.pdf
So I think no need to add any notes.
--
SASANO Takayoshi (JG1UAA)
, axp221_sensdata },
{ "x-powers,axp305", "AXP305", axp806_regdata },
+ { "x-powers,axp313a", "AXP313A", axp313a_regdata },
{ "x-powers,axp803", "AXP803", axp803_regdata, axp803_sensdata },
{ "x-powers,axp805", "AXP805", axp806_regdata },
{ "x-powers,axp806", "AXP806", axp806_regdata },
--
SASANO Takayoshi (JG1UAA)
Hi,
changed step -> nsteps, and indent is fixed. Here is new diff.
Can I commit this?
Regards,
--
SASANO Takayoshi (JG1UAA)
Index: axppmic.c
===
RCS file: /cvs/src/sys/dev/fdt/axppmic.c,v
retrieving revision 1.16
diff -u
the diff, but it is huge due to modifying axppmic_data table.
Any comments are welcomed.
--
SASANO Takayoshi (JG1UAA)
Index: axppmic.c
===
RCS file: /cvs/src/sys/dev/fdt/axppmic.c,v
retrieving revision 1.16
diff -u -p -r1.16
ee this timeout of re(4) and
that is solved by this MSI tweak.
Or, please tell me if there is any other workarounds.
Regards,
--
SASANO Takayoshi (JG1UAA)
ping?
OpenBSD-7.1 still occur this.
--
SASANO Takayoshi (JG1UAA)
On Sat, 16 Oct 2021 12:21:57 +0900,
SASANO Takayoshi wrote:
>
> Hi,
>
> At least 6.9 and 7.0 (and -current) sometimes shows a dmesg that:
>
> puc1 at pci1 dev 0 function 1 "ASIX AX99100" rev
int i;
int ncont = 0;
- for (i = 0; i < 10; i++) {
+ for (i = 0; i < 24; i++) {
char path[PATH_MAX];
snprintf(path, sizeof(path), "%s%d", USBDEV, i);
--
SASANO Takayoshi (JG1UAA)
endpoints->ep_bulkin = bin;
+ endpoints->ep_bulkin_size = binsize;
endpoints->ep_bulkout = bout;
return 0;
--
SASANO Takayoshi (JG1UAA)
Hi,
> clang kernels are built with -Wno-unused-but-set-variable
> try running 'make config' again
oops, I forget 'make config'. Build process works good after that.
Thank you!
--
SASANO Takayoshi (JG1UAA)
RATE] = 1 / [H PERIOD] / [TOTAL V LINES] * 100
@@ -442,6 +449,7 @@ vesagtf_mode_params(unsigned h_pixels, u
v_field_rate / 2 : v_field_rate;
print_value(14, "[V FRAME RATE]", v_frame_rate);
+#endif
/* 15. Find number of pixels in left margin:
ok?
--
SASANO Takayoshi (JG1UAA)
works good, but I think there is better build order.
--
SASANO Takayoshi (JG1UAA)
obe(struct com_softc *sc)
fifo |= FIFO_ENABLE_64BYTE;
com_write_reg(sc, com_fifo, fifo);
+ delay(100);
for (len = 0; len < 256; len++) {
com_write_reg(sc, com_data, (len + 1));
--
SASANO Takayoshi (JG1UAA)
/* do nothing */
+ break;
+ }
com_attach_subr(sc);
}
--
SASANO Takayoshi (JG1UAA)
ping
On Mon, 18 Nov 2019 14:56:46 +0900,
SASANO Takayoshi wrote:
>
> Hello,
>
> At least OpenBSD-6.5 and 6.6's ftpd does not work NLIST command with any
> -option like this.
>
>
> ftp> nlist
> 150 Opening ASCII mode data connection for 'file list'.
>
retrieve(RET_NLIST, dirname);
goto out;
}
perror_reply(550, whichf);
--
SASANO Takayoshi (JG1UAA)
tole32(
EHCI_QH_SET_HUBA(hshubaddr) |
EHCI_QH_SET_PORT(hshubport) |
- EHCI_QH_SET_CMASK(0x1c) /* XXX */
+ EHCI_QH_SET_CMASK(0xe0)
);
}
sqh->qh.qh_curqtd = htole32(EHCI_LINK_TERMINATE);
--
SASANO Takayoshi (JG1UAA)
if (xfertype != UE_ISOCHRONOUS) {
--
SASANO Takayoshi (JG1UAA)
(>if_snd, m_head);
+ ifq_deq_rollback(>if_snd, m_head);
ifq_set_oactive(>if_snd);
return;
}
@@ -655,9 +654,9 @@ ugl_init(void *xsc)
}
ifp->if_flags |= IFF_RUNNING;
- splx(s);
-
ifq_clr_oactive(>if_snd);
+
+ splx(s);
dev 0 function 3 "ASIX AX99100" rev 0x00: ports: 1 com
com7 at puc3 port 0 apic 5 int 16: st16650, 32 byte fifo
ok?
--
SASANO Takayoshi (JG1UAA) <u...@mx5.nisiq.net>
Index: pcidevs
===
RCS file: /cvs/src/sy
pings[i].t = comconsiot;
- sc->sc_bar_mappings[i].h = comconsioh;
- sc->sc_bar_mappings[i].s = COM_NPORTS;
+ sc->sc_bar_mappings[i].s = size;
sc->sc_bar_mappings[i].mapped = 1;
continue;
}
Regards,
--
SASANO Takayoshi <u...@mx5.nisiq.net>
s written in Chinese, use Google Translate.
Regards,
--
SASANO Takayoshi <u...@mx5.nisiq.net>
Index: pcidevs
===
RCS file: /cvs/src/sys/dev/pci/pcidevs,v
retrieving revision 1.1790
diff -u -p -r1.1790 pcidevs
--- pcidevs
th of Tx/Rx FIFO,
it uses MCR_LOOPBACK to enter loopback mode.
I found TX382B does not loopback with setting MCR_LOOPBACK,
and this cause com_fifo_probe() detects no FIFO.
It is difficult to write a special code to com.c, I think TX382B should
work without Tx/Rx FIFO. There is other good and cheap UART
mp; RDCIDE_PATR_EN(channel)) == 0) {
printf("%s: %s ignored (disabled)\n",
sc->sc_wdcdev.sc_dev.dv_xname, cp->name);
+ cp->hw_ok = 0;
continue;
}
pciide_map_compat_intr(pa, cp, channel, interface);
--
SASANO Takayoshi <u...@mx5.nisiq.net>
Hello,
Here is the driver for Silicon Labs CP2110 USB HID based UART.
It called uhidcom(4) and now renamed to uslhcom(4).
Now working on -current.
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: arch/i386/conf/GENERIC
===
RCS file
),
but currently it is not supported --- too expensive to buy evaluation board.
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: arch/i386/conf/GENERIC
===
RCS file: /cvs/src/sys/arch/i386/conf/GENERIC,v
retrieving revision 1.792
diff -u -p -u -p
At Wed, 17 Dec 2014 22:43:40 +1100,
Jonathan Gray wrote:
On Wed, Dec 17, 2014 at 07:49:59PM +0900, SASANO Takayoshi wrote:
Hi,
I am trying to write a driver for Silicon Labs CP2110 USB HID based UART.
Here is work-in-progress code, and it seems to set uca.uhidev properly.
(I wrote
Hi,
At Wed, 19 Nov 2014 10:56:15 +0100,
Martin Pieuchot wrote:
On 18/11/14(Tue) 05:25, SASANO Takayoshi wrote:
Hi all,
I bought Silicon Labs CP2110-EK USB HID-to-UART evaluation kit
and connected to OpenBSD box.
uslcom(4) tries to use CP2110, but the device is different from
=19
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
THIS WITHOUT INCLUDING THAT INFORMATION!
ddbabd
I think sxiuartcngetc() have no problem and something makes worse.
Do I have to check page table (memory attribute of ARMv7 MMU)
when running UKC?
--
SASANO Takayoshi u...@mx5.nisiq.net
Hello,
Here is the log of new image.
Booting with -c option, UKC still hangs up.
I hope the log helps debugging.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
U-Boot SPL 2014.04-10694-g2ae8b32-dirty (Oct 01 2014 - 17:40:04)
Board: Bananapi
DRAM: 1024 MiB
CPU: 96000Hz, AXI/AHB/APB: 3/2
2.0
uhub1 at usb1 Allwinner EHCI root hub rev 2.00/1.00 addr 1
(hang-up)
--
SASANO Takayoshi u...@mx5.nisiq.net
rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved. http://www.OpenBSD.org
User Kernel Config
UKC
--
SASANO Takayoshi u...@mx5.nisiq.net
=20140501232036142
it is written in Japanese but maybe good hint)
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
[case 1]
U-Boot SPL 2014.04-10694-g2ae8b32-dirty (Oct 01 2014 - 17:40:04)
Board: Bananapi
DRAM: 1024 MiB
CPU: 96000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600
U-Boot
?
--
SASANO Takayoshi u...@mx5.nisiq.net
what is
happening. What can I do for solving this problem?
--
SASANO Takayoshi u...@mx5.nisiq.net
[uEnv.txt]
mmcboot=mmc rescan; fatload mmc 0 0x6000 bsd.umg bootm 0x6000;
bootargs=sd0a:/bsd;
uenvcmd=run mmcboot;
[1st try - hang up
Hi,
Try this[1] kernel and have a look if it has the same issue or not.
Kernel did not started... U-Boot says checksum is ok, so maybe
.umg file is not corrupted.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
U-Boot SPL 2014.04-10694-g2ae8b32-dirty (Oct 01 2014 - 17:40:04)
Board
fifo
I referred the following pages:
http://www.spinics.net/lists/linux-serial/msg11744.html
http://kent-vandervelden.blogspot.jp/2014/08/linux-parallel-port-cards.html
Can I commit?
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: pucdata.c
Hello,
Here is Nanjing QinHeng Electronics (Winchiphead)'s CH382
PCIe-UART controller's PCI vendor/device ID.
Chinese Datasheet can be obtained from
http://www.wch.cn/downloads/downfile.php?id=140
Can I commit?
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: pcidevs
, but poor performance
boost because CPU is too slow... 109min - 101min :-(.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: pciide.c
===
RCS file: /cvs/src/sys/dev/pci/pciide.c,v
retrieving revision 1.345
diff -u -p -r1.345
-product RDC R6061_EHCI 0x6061 R6061 USB
+product RDC R6060_OHCI 0x6060 R6060 USB OHCI
+product RDC R6061_EHCI 0x6061 R6061 USB EHCI
/* Realtek products */
product REALTEK RTS52090x5209 RTS5209 Card Reader
--
SASANO Takayoshi u...@mx5.nisiq.net
Hello,
Recently I bought Arduino board which uses Nanjing QinHeng (WinChipHead)
CH340T USB-UART bridge via eBay, and I found uchcom(4) did not work.
At misc@, other user reported similar problem. [1]
The uchcom(4) comes from NetBSD and it seems to be worked at that time.
I found that
/function of UCHCOM_REG_LCR1 has been changed,
and generated results are doubtful. So I use Linux's magic numbers.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Hi,
Simply magic values are rewrited with #define.
If these values need to be disassembled, please take a while...
SASANO Takayoshi u...@mx5.nisiq.net
Index: uchcom.c
===
RCS file: /cvs/src/sys/dev/usb/uchcom.c,v
retrieving
Hello,
I found some debug messages need to be fixed in sys/dev/usb/umodem.c.
Can I commit the diff?
SASANO Takayoshi u...@mx5.nisiq.net
Index: umodem.c
===
RCS file: /cvs/src/sys/dev/usb/umodem.c,v
retrieving revision 1.55
Hi,
Thanks, here is a slightly reworked diff that does the wait in a way
that's more in line with other bits of azalia(4) that wait for a bit
in a register to go on or off.
Okay, there is no problem with my 86duino EduCake. Thanks.
--
SASANO Takayoshi u...@mx5.nisiq.net
Hello,
This can wait til after 5.5, but I made the diff since I was looking
at the code.
ok by sasano@, it works on my 86duino EduCake!
SASANO Takayoshi u...@mx5.nisiq.net
.
(Vortex86EX's CORB DMA did not required any delay. It starts immediately.)
Here is the patch to add delay.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: azalia.c
===
RCS file: /cvs/src/sys/dev/pci/azalia.c,v
retrieving revision 1.209
for this problem.
Comments or ok?
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: if_udav.c
===
RCS file: /cvs/src/sys/dev/usb/if_udav.c,v
retrieving revision 1.64
diff -u -p -r1.64 if_udav.c
--- if_udav.c 15 Nov 2013 10:17:39 -
Hello,
if_ugl.c has similar issue, and I think this should be fixed.
ok to commit?
SASANO Takayoshi u...@mx5.nisiq.net
Index: if_ugl.c
===
RCS file: /cvs/src/sys/dev/usb/if_ugl.c,v
retrieving revision 1.2
diff -u -p -r1.2
Hello,
jca@ privately advised that I should write my own copyright to
describe who modified the code.
I am planning to add notice like if_axe.c and sent the diff to
him but there is no answer (too busy?). So I ask here.
Is there any good solution?
Thanks,
SASANO Takayoshi u...@mx5
-cdce_unit = self-dv_unit;
sc-cdce_udev = uaa-device;
sc-cdce_ctl_iface = uaa-iface;
id = usbd_get_interface_descriptor(sc-cdce_ctl_iface);
And, sc-sc_unit of sys/dev/usb/if_cdcef.c seems to have save problem.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Hello,
I committed ugl(4) driver to source tree.
The driver is derived from upl(4) driver, so licence is NetBSD.
Thanks.
--
SASANO Takayoshi u...@mx5.nisiq.net
At Fri, 15 Nov 2013 10:56:37 +0100,
Martin Pieuchot wrote:
On 14/11/13(Thu) 17:44, Brad Smith wrote:
On 14/11/13 3:29 PM, SASANO
notice --- NetBSD or OpenBSD.
if_ugl.c is based on if_upl.c, and if_upl.c has NetBSD's one.
Regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
Index: arch/alpha/conf/GENERIC
===
RCS file: /cvs/src/sys/arch/alpha/conf/GENERIC,v
retrieving
://circuithijacker.blogspot.jp/2007/02/usb-host-to-host-cables-with-slax-linux.html
[2] http://www.linux-usb.org/usbnet/
Best regards,
--
SASANO Takayoshi u...@mx5.nisiq.net
SASANO Takayoshi u...@mx5.nisiq.net
Index: uthum.c
===
RCS file: /cvs/src/sys/dev/usb/uthum.c,v
retrieving revision 1.23
diff -u -p -r1.23 uthum.c
--- uthum.c 8 May 2013 08:26:25 - 1.23
+++ uthum.c 26 Sep 2013 20:28:12
Hi all,
Here is the driver for Microdia's USB TEMPer, take 3.
http://www.uaa.org.uk/gomitext/2013/20130905/20130905.diff
Thanks to mpi@ and testers of tech@.
man is not yet, sorry.
Regards,
SASANO Takayoshi u...@mx5.nisiq.net
* at uhidev? into GENERIC for alpha, amd64, armish, hppa, i386,
landisk, loongson, macppc, sgi (IP27, IP30, IP32), socppc and sparc64.
Regards,
SASANO Takayoshi u...@mx5.nisiq.net
*/
+sc-sc_num_sensors = sc-sc_ibuf[1];
How can you be sure sc_ibuf contains the data you asked for?
Well, sanity check will be required.
Cheers,
--
SASANO Takayoshi u...@mx5.nisiq.net
) and already use Microdia's-variant-patched
uthum(4) driver, revert original uthum(4).
ok or comments, please.
Cheers,
--
SASANO Takayoshi u...@mx5.nisiq.net
Hello, Luis.
Now I am rewriting a driver for Microdia's USB TEMPer with
advices from yuo@ and deraadt@.
Please wait a while and thank you for trying my patch.
Thanks.
--
SASANO Takayoshi u...@mx5.nisiq.net
-wip.diff
Thanks,
SASANO Takayoshi u...@mx5.nisiq.net
, */
{ PCI_VENDOR_OXFORD2, PCI_PRODUCT_OXFORD2_OX16PCI954, 0, 0 },
By the way, does someone know how to use over 230400bps?
I cannot find B460800 and B921600 in termios.h.
Regards,
SASANO Takayoshi u...@mx5.nisiq.net
,
+ NULL, ahci_ati_sb700_attach },
{ PCI_VENDOR_ATI, PCI_PRODUCT_ATI_SB600_SATA,
NULL, ahci_ati_sb600_attach },
SASANO Takayoshi u...@mx5.nisiq.net, sas...@cvs.openbsd.org
-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xd000, size 0x1000
inteldrm0 at vga1: apic 4 int 16
drm0 at inteldrm0
Intel G41 Video rev 0x03 at pci0 dev 2 function 1 not configured
SASANO Takayoshi u...@mx5.nisiq.net
Oops, try again...
At Tue, 09 Nov 2010 20:48:37 +0900,
SASANO Takayoshi wrote:
Hello,
Phenom 9500 has TLB errata and this should be workarounded by BIOS.
But some BIOS do nothing by default, I think the warning is needed.
Here is the patch, please review.
--
amd64errata.c
, 1.17 and 1.18
specialreg.h
- add definitions for amd64errata.c
- modified NB_CFG_DISIOREQLOCK and DC_CFG_DIS_CNV_WC_SSO,
they are misdefined (see src/sys/arch/x86/include/specialreg.h
of NetBSD, revision 1.48 and 1.49)
--
SASANO Takayoshi (JG1UAA/@uaa) [http
66 matches
Mail list logo
