Kejia
Rick gave you some very good information. I have to agree that the SRDs are
pretty tough from my experience. I have several 5061s. But they do need the
bias and the RF at the level indicated in the manual. Not to much not to
little.
There is also a RF attenuator knob on the multiplier. So
Dear Richard,
Very nice to hear from you, and thank you a lot for the help!
Indeed, I have cleaned the erosion still not working.
I am trying to now* remeasure the break voltage of the diode*.
I suspect that the doping get diffused in the isolation layer after age,
which make it a good diode,
Absolutely I see what you describe below. Bournes actually has an old paper
that describes all of these issues, but they do not seem to address them in
selection guides these days. I have no way to find out which are good until
I try 50 of them. I get a few that are just awful, basically a random
Another very irritating "feature" of pots is that over time the wiper can
deform the resistance element. When you go to adjust a pot (like when making a
calibration adjustment on an old piece of equipment) it can be very difficult
to get (and keep) the setting where you want it to be if the
On Sat, 23 Dec 2017 21:00:39 +
Stephan Sandenbergh wrote:
> I guess I'm just worried that I might be missing something obvious here?
> And I know there is no better place to ask such a question other than on
> time-nuts :)
No, your derivation is correct. Though
Hi,
Normally it's best to adjust a multi-turn trimmer in just one
direction, so if you do overshoot, go back 2 or 3 turns and then on
again to the place you want to be. The imperfections in the mechanism
will drive you nuts (in a bad way) if you try to do fine adjustments
back and forth.
It's
In message , "Brian, WA1ZMS"
writes:
>I have seen similar issues to Dana's and have told myself it must
>be torque left in the gear-train within the pot. Maybe all in my
>mind as well, but it seems real to me on some equipment.
Or simply
I have seen similar issues to Dana's and have told myself it must be torque
left in the gear-train within the pot. Maybe all in my mind as well, but it
seems real to me on some equipment.
-Brian, WA1ZMS
> On Dec 24, 2017, at 5:26 PM, Dana Whitlow wrote:
>
> I think I
I think I need to clarify what I mean by "backlash". It is not simple free
play in
the adjustment mechanism- it is something much more irritating, as follows:
I sneak up on the desired result, but manage to overshoot slightly. So I
back
off on the screw, and find that at first the result
John wrote:
I didn't really notice much backlash, though when setting oscillators I try to approach
(slowly) from one direction until it's "good enough" and then stop, to avoid
that problem.
The hot tip is not to just "sneak[] up on the sweet spot and then walk[]
away," as Dana put it.
I should comment that my bad experiences were in trimming out opamp DC
offsets.
As I recall, the amount of backlash was equivalent to a fair fraction of
one turn
of the shaft.
I never fully trusted the philosophy of sneaking up on the sweet spot and
then
walking away- I felt it was necessary to
I extensively studied the 5061 harmonic generator when I
was designing the harmonic generator in the 5071A.
We are now going on 30 years since that work. The diode
had some HP part number. Even if you knew this part
number, you would need to have the Part Information Report
microfiche that gave
I am using a Bournes 3224 and I do see backlash issues. I do come from one
direction to set it and if I overshoot, I go way past and come back from
the other direction. I also see non-monotonic sections. If one of those is
where you want to set the frequency, it is pretty hard to do. I chose one
Hi
With these little OCXO’s you likely will move them 0.1 ppb simply walking
past the bench. If they have a total of 0.25 ppm of trim, a 25 turn pot will
get
you 1 ppb per turn. Setting these pots to 1/10 turn is not all that crazy.
Yes, there are a bunch of assumptions made there and your
I didn't really notice much backlash, though when setting oscillators I try to
approach (slowly) from one direction until it's "good enough" and then stop, to
avoid that problem.
On Dec 24, 2017, 11:28 AM, at 11:28 AM, Dana Whitlow
wrote:
>John,
>
>Do you notice a
John,
Do you notice a backlash effect when homing in on the desired setting with
those
tripots? I last used such things back in the 1980's, and remember often
having
enough backlash to make close trimming rather difficult.
I wonder if they have gotten better in that regard.
Dana
On Sun, Dec
Hi
The nice thing is that the footprint on the Pulse Puppy is pretty generic.
There are a lot of OCXO’s on eBay that will fit the pattern on the board.
When you get into the more exotic parts, the footprints (and functions)
don’t tend to be as standardized.
The small package OCXO’s will
I'm glad that the PulsePuppy post spawned some good discussion!
The pot I'm using is a Bournes 3296W-1-103LF which is a 25-turn, 10K,
cermet pot, spec'd at 100ppm/degree, so it's not anything super fancy.
The number of turns provides decent setability, and it seems to be a
good match for the
Hi
The other issue with putting in an amp is noise. You really do not want to feed
a bunch of added “stuff” into the FM modulation port on the oscillator. You get
some thermal noise from the pot, so it is never zero. How close you need to get
to zero - who knows? When the part was tested to see
Dear All,
Happy Christmas!
May I know if anyone knows the part number or the specification of the step
recovery diode in the harmonic
generator for the old HP 5601A cesium frequency standard?
I recently received this toy. The cesium tube seems to be OK, and I had
located the problem being
no
Mark is correct, but with a caveat: Unless the pot slider sees a load
impedance that
is much much larger than the pot's end-to-end resistance, contact resistance
variations can also play a big role, especially when the pot gets old. For
this reason
alone I favor sticking with the 3-terminal
In message
, Mark
Goldberg writes:
>When the pot is used as a voltage divider, theoretically it should have
>the same TC throughout, so temperature effects should not affect the divide
>ratio or the output.
I
Can you specify what pot you have used? I am using some for my TCXO boards
and am not quite happy with the settability or mechanical stability.
resulting in noise and higher Allan Deviation.
A low noise regulator driving it also helped.
I subscribe to the opinion to not use any extra resistors.
23 matches
Mail list logo