Kopia: mag...@rubidium.se
Rubrik: Re: [time-nuts] Brandywine GPS-4 OCXO
Hi
Pictures probably would help :)
Bob
> On May 20, 2017, at 8:00 AM, Magnus Danielson <mag...@rubidium.dyndns.org>
> wrote:
>
> Hi,
>
> Does someone happen to know what OCXO sits in the Brandywine GPS-4 G
Hi
Pictures probably would help :)
Bob
> On May 20, 2017, at 8:00 AM, Magnus Danielson
> wrote:
>
> Hi,
>
> Does someone happen to know what OCXO sits in the Brandywine GPS-4 GPSDO?
> It's pretty good sized OCXO, possibly double-oven. It has a screw on the side
Jeroen,
I have v2.1 v2.2 of the PDF Manual. No real differences that I can see, just
a couple non-necessary pages.
The only other bit of info I have that might be of some use, I saved the
startup text a while back, it should look something like
this:
L=load ESC=RUN.
Initialise - Clear
Hello Hal,
The serial connection is not the problem (unfortunately). It seems a
thermal problem When I switch on the unit it takes a couple of
minutes before the Error-LED starts flashing. Doing a fast power-cycle
immediately gives an error-warning (the red-LED start flashing almost
The serial connection is not the problem (unfortunately). It seems a
thermal problem When I switch on the unit it takes a couple of
minutes before the Error-LED starts flashing. Doing a fast
power-cycle immediately gives an error-warning (the red-LED start
flashing almost immediately
Jeroen,
I have a GPS-4 too and gathered some documentation for it a while back. I'll
have to dig around on my hard drive but I seem to
recall having at least two versions of the PDF manual. I do not know what the
difference was between them. Anything I can find I'll
be sure to let you (and the
Jeroen Bastemeijer skrev:
Dear All,
I decided to switch on my Brandywine GPS-4 after some time on the shelf.
After start-up it takes some time, then the Alarm-LED starts flashing...
When I look at the data coming from the serial port it keeps saying
L=load ESC=run. Unfortunately the unit
Dear Magnus,
Thank you for your response!
The unit used to work so dip-switch, cable etc. are OK. The thing I
suspect is indeed, some problem with the FLASH and/or EPROM. However, I
have no useful source of information about that.
The initial question: L=load ESC=run has something to do
The unit used to work so dip-switch, cable etc. are OK. The thing
I suspect is indeed, some problem with the FLASH and/or EPROM.
However, I have no useful source of information about that.
Did it work with the serial port connected to a PC like you are using now?
Or did you just see
of precise time and frequency measurement
time-nuts@febo.com
Sent: Sunday, April 22, 2007 10:54 AM
Subject: Re: [time-nuts] Brandywine GPS-4 (0010-0040) manual
check
http://www.ko4bb.com/ham_radio/Manuals/4_GPS_Stuff/GPS4-Manual_v2.2-1.pdf
Didier KO4BB
Hi.
I'm looking for manual
Oooops:
http://www.ko4bb.com/ham_radio/Manuals/4_GPS_Stuff/GPS4-Manual_v2.2.pdf
Sorry for the typo...
Didier KO4BB
ji1qgk wrote:
Hi Didier and Jason
Thanks for uploading the manual.
However, your page is not found now. Could you confirm it?
My unit GPS locked and true 10MHz output but
check
http://www.ko4bb.com/ham_radio/Manuals/4_GPS_Stuff/GPS4-Manual_v2.2-1.pdf
Didier KO4BB
Hi.
I'm looking for manual of Brandywine GPS-4 (model:0010-0040).
Does anyone know where to obtain it?
Thanks
Hiro
___
time-nuts
Thanks to Bob, the Brandywine GPS-4 manual is at
http://www.ko4bb.com/ham_radio/Manuals/2_GPS_Stuff
Didier KO4BB
Original Message
Subject:RE: [time-nuts] Looking For Brandywine GPS-4 User Manual
Date: Thu, 21 Dec 2006 10:21:42 -0500
From: Robert E. Martinson
13 matches
Mail list logo