From: Haibo Chen
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo
Signed-off-by: Haibo Chen
---
drivers/mmc/fsl_esdhc_imx.c | 7 ++-
1 file changed, 6 insertions(+),
From: Haibo Chen
Currently, readl/writel and esdhc_read32/esdhc_write32 are used. To align
the usage, change to only use esdhc_read32/esdhc_write32.
Signed-off-by: Haibo Chen
---
drivers/mmc/fsl_esdhc_imx.c | 64 ++---
1 file changed, 32 insertions(+), 32
Enable eMMC HS400 mode support on LX2160ARDB.
Signed-off-by: Yangbo Lu
---
Changes for v2:
- None.
Changes for v3:
- None.
Changes for v4:
- None.
---
configs/lx2160ardb_tfa_SECURE_BOOT_defconfig | 1 +
configs/lx2160ardb_tfa_defconfig | 1 +
Fix mmc->clock with actual clock which is divided by the
controller, and record it with priv->clock which was removed
accidentally.
Signed-off-by: Yangbo Lu
---
Changes for v2:
- Added this patch.
Changes for v3:
- None.
Changes for v4:
- None.
---
Add properties related to eMMC HS400 mode.
mmc-hs400-1_8v;
bus-width = <8>;
They had been already in kernel dts file since the first
lx2160ardb dts patch.
b068890 arm64: dts: add LX2160ARDB board support
Signed-off-by: Yangbo Lu
---
Changes for v2:
- None.
Changes for v3:
-
The process for eMMC HS400 mode for eSDHC is,
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value
From: Konstantin Porotchkin
Add support for additional EspressoBIN board with installed
eMMC device (U11).
EspressoBIN boards with eMMC installed should use the DTS named
armada-3720-espressobin-emmc.
Update build documentation accordingly.
Change-Id: Id1a4f3ca01a6e52df57bf7279f33f0fe45f8ed18
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> At present U-Boot sets a loader type of 8 which means LILO version 8,
> according to the spec. Update it to 0x80, which means U-Boot with no
> particular version.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no
Clean TBCTL[TB_EN] manually during init since it is not able to
be reset by reset all operation.
Signed-off-by: Yangbo Lu
---
Changes for v2:
- None.
Changes for v3:
- None.
Changes for v4:
- None.
---
drivers/mmc/fsl_esdhc.c | 3 +++
1 file changed, 3 insertions(+)
Add a reinit() callback for mmc rescan.
Signed-off-by: Yangbo Lu
Reviewed-by: Jaehoon Chung
---
Changes for v2:
- None.
Changes for v3:
- None.
Changes for v4:
- Added Reviewed-by.
---
drivers/mmc/fsl_esdhc.c | 9 +
1 file changed, 9 insertions(+)
diff --git
For DM_MMC, the controller re-initialization is needed to
clear old configuration for mmc rescan.
Signed-off-by: Yangbo Lu
Reviewed-by: Jaehoon Chung
---
Changes for v2:
- None.
Changes for v3:
- None.
Changes for v4:
- Added Reviewed-by.
---
drivers/mmc/mmc-uclass.c |
This patch-set is to support eMMC HS200 and HS400 speed modes for
eSDHC, and enable them on LX2160ARDB board.
CI build link
https://travis-ci.org/github/yangbolu1991/u-boot-test/builds/720875619
Changes for v2:
- Added two patches to fix stability issue.
Changes for v3:
-
Dear Simon,
make chromebook_coral_defconfig
make
using gcc (Debian 10.2.0-5) 10.2.0 and GNU ld (GNU Binutils for Debian)
2.35 results in:
ld.bfd: drivers/built-in.o:drivers/bios_emulator/x86emu/sys.c:47:
multiple definition of `_X86EMU_env';
arch/x86/lib/built-in.o:arch/x86/lib/bios.c:25: first
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> Use IS_ENABLED() instead of #ifdef in this file.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no changes since v1)
>
> arch/x86/lib/zimage.c | 14 +-
> 1 file changed, 5 insertions(+), 9
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> At present the 'zboot' command does everything in one go. It would be
> better if it supported sub-commands like bootm, so it is possible to
> examine what will be booted before actually booting it.
>
> In preparation for this, move the
Hi Andy,
On Thu, Aug 20, 2020 at 6:02 PM Andy Shevchenko
wrote:
>
> start.S does nothing and can be safely removed. Makefile is still being used
> by the build system, so simply drop the rule from it.
>
> Signed-off-by: Andy Shevchenko
> Reviewed-by: Simon Glass
> ---
> v2: added Rb tag(s)
>
>
Support tuning process for eMMC HS200 for eSDHC.
Signed-off-by: Yangbo Lu
---
Changes for v2:
- None.
Changes for v3:
- Rebased.
Changes for v4:
- None.
---
drivers/mmc/fsl_esdhc.c | 106 ++--
include/fsl_esdhc.h | 17
Some controllers may have difference between HS200 tuning
and HS400 tuning, such as different registers setting,
different procedure, or different errata.
This patch is to add a hs400_tuning flag to identify the
tuning for HS400 mode.
Signed-off-by: Yangbo Lu
---
Changes for v2:
- None.
There was a fix-up for eMMC HS400 stability issue in Linux.
Patch link:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/
commit/?id=58d0bf843b49fa99588ac9f85178bd8dfd651b53
Description:
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests,
Add a mmc_hs400_prepare_ddr() interface for controllers
which needs preparation before switching to DDR mode for
HS400 mode.
Signed-off-by: Yangbo Lu
---
Changes for v2:
- None.
Changes for v3:
- None.
Changes for v4:
- Checked returning of mmc_hs400_prepare_ddr().
---
On Tue, Sep 01, 2020 at 02:15:32PM +0800, Bin Meng wrote:
> Hi Andy,
>
> On Thu, Aug 20, 2020 at 6:02 PM Andy Shevchenko
> wrote:
> >
> > start.S does nothing and can be safely removed. Makefile is still being used
> > by the build system, so simply drop the rule from it.
> >
> > Signed-off-by:
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> To help reduce the size and complexity of load_zimage(), move the code
> that reads the kernel version into a separate function. Update
> get_boot_protocol() to allow printing the 'Magic signature' message only
> once, under control of its
On Tue, Sep 1, 2020 at 4:33 PM Andy Shevchenko
wrote:
>
> start.S does nothing and can be safely removed. Makefile is still being used
> by the build system, so simply replace the rule in it. We use stub C-file
> like it's done for other boards.
>
> Signed-off-by: Andy Shevchenko
> Reviewed-by:
From: Meenakshi Aggarwal
Signed-off-by: Meenakshi Aggarwal
---
include/configs/lx2160aqds.h | 2 +-
include/configs/lx2160ardb.h | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/include/configs/lx2160aqds.h b/include/configs/lx2160aqds.h
index 3dd071f..1cc015c 100644
---
+Andy Shevchenko
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> This header is missing a few of the newer features from the specification.
> Add these as well as a link to the spec. Also use the BIT() macros where
> appropriate.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang
On Tue, Sep 01, 2020 at 10:05:00AM +0300, Andy Shevchenko wrote:
> On Tue, Sep 01, 2020 at 02:15:32PM +0800, Bin Meng wrote:
> > On Thu, Aug 20, 2020 at 6:02 PM Andy Shevchenko
> > wrote:
...
> > > -obj-y += start.o
> >
> > Unfortunately this does not build.
> >
> > We possibly need to fix
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply replace the rule in it. We use stub C-file
like it's done for other boards.
Signed-off-by: Andy Shevchenko
Reviewed-by: Simon Glass
Reviewed-by: Bin Meng
---
v3: fixed linker error (Bin)
On Fri, 2020-08-07 at 17:32 +0800, Chunfeng Yun wrote:
> The start address of dout, pullen and pullsel ragnes are wrong,
> so fix up them.
>
> Signed-off-by: Chunfeng Yun
> ---
> drivers/pinctrl/mediatek/pinctrl-mt8512.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff
Hi Frank,
Would you please forward this mail to Marek, he doesn't receive email
sent from MediaTek, thanks a lot
Hi Marek,
I always receive eth following massage, it seems the same for my
workmate,
---
Delivery has failed to these recipients or groups:
ma...@denx.de
A problem occurred while
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the property,
while the device tree defines the address
On Tue, Sep 01, 2020 at 10:01:18PM +, Reuben Dowle wrote:
> This patch allows uboot scripts make choices about where to boot from based
> on
> the active mmc boot partition. This allows having two copies of kernel,
> filesystems etc, and choosing which to boot from based off the active
>
Hi,
Just tried out v2020.10-rc3 on my T2080RDB and I've got the following
splat. Haven't had a chance to decode it yet (pointers on how to
translate the addresses for powerpc welcome) but I figured I'd get
this out just in case anyone was looking at the T2080RDB.
SPI boot...
From: Meenakshi Aggarwal
This patch set add support for LX2162AQDS board.
LX2162A is a variant of LX2160A.
Meenakshi Aggarwal (2):
armv8: lx2162a: Add Soc changes to support LX2162A
armv8: lx2162aqds: Add support for LX2162AQDS platform
arch/arm/Kconfig |
From: Meenakshi Aggarwal
This patch add base support for LX2162AQDS board.
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 4GB ddr memory, i2c, micro-click module, microSD card,
serial console, qspi nor flash, qsgmii, sgmii, 25g, 40g, 50g
Hi Simon,
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> At present it is not possible to tell from a script where the setup block
> is, or where the image was loaded to. Add environment variables for this.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no
Hi Alper,
On Tue, 1 Sep 2020 at 04:35, Simon Glass wrote:
>
> At present if a FIT references a missing external blob, binman reports an
> error, even if the image is supposed to allow this.
>
> Propagate this setting down to the child sections of the FIT, so that the
> behaviour is consistent.
>
On 9/1/20 6:51 AM, Heinrich Schuchardt wrote:
> On 8/18/20 11:00 AM, Heinrich Schuchardt wrote:
>> On 11.08.20 12:32, Sean Anderson wrote:
>>> On 8/11/20 3:50 AM, Heinrich Schuchardt wrote:
On 11.08.20 08:20, Rick Chen wrote:
> Hi Heinrich
>
>> From: Heinrich Schuchardt
At present we have an Entry_blob_ext which implement a blob which holds an
external binary. We need to support other entry types that hold external
binaries, e.g. Entry_blob_named_by_arg. Move the support into the base
Entry class to allow this.
Signed-off-by: Simon Glass
---
(no changes since
At present binman warns about missing external blobs only when the
BUILD_ROM is defined. Enable this behaviour always, since many boards
are starting to use these (e.g. ARM Trusted Firmware's BL31).
Signed-off-by: Simon Glass
---
(no changes since v2)
Changes in v2:
- Add new patch to support
If an entry argument is needed by an entry but the entry argument is not
present, then a strange error can occur when trying to read the file.
Fix this by allowing arguments to be required. Select this option for the
cros-ec-rw entry. If a filename is provided in the node, allow that to be
used.
This series allows binman to generate FITs that include multiple DTB
images and the configuration to use them.
It is then possible to remove the sunxi FIT generator script, so this
series handles that also.
With this, sunxi is fully converted to use binman.
Note: This series is available at
At present the Python sequential-write interface can produce an error when
it calls fdt_finish(), since this needs to add a terminating tag to the
end of the struct section.
Fix this by automatically expanding the buffer if needed.
Signed-off-by: Simon Glass
---
(no changes since v1)
Tidy up a few test functions which lack argument comments. Rename one that
has the same name as a different test.
Also fix up the comment for PrepareImagesAndDtbs().
Signed-off-by: Simon Glass
---
(no changes since v1)
tools/binman/control.py | 5 +
tools/binman/ftest.py | 22
From: Meenakshi Aggarwal
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 4GB ddr memory, i2c, micro-click module, microSD card,
serial console, qspi nor flash, qsgmii, sgmii, 25g, 40g, 50g network
interface,one usb 3.0 and serdes interface to
On 8/18/20 11:00 AM, Heinrich Schuchardt wrote:
On 11.08.20 12:32, Sean Anderson wrote:
On 8/11/20 3:50 AM, Heinrich Schuchardt wrote:
On 11.08.20 08:20, Rick Chen wrote:
Hi Heinrich
From: Heinrich Schuchardt [mailto:xypron.g...@gmx.de]
Sent: Tuesday, August 11, 2020 11:57 AM
To: Rick
Signed-off-by: John Robertson
---
arch/mips/dts/pic32mzda.dtsi | 11 +++
1 file changed, 11 insertions(+)
diff --git a/arch/mips/dts/pic32mzda.dtsi b/arch/mips/dts/pic32mzda.dtsi
index 4c8b7a9a0b..8aff9eb812 100644
--- a/arch/mips/dts/pic32mzda.dtsi
+++ b/arch/mips/dts/pic32mzda.dtsi
Hi Gary,
On Thu, 27 Aug 2020 at 11:51, Gary Bisson
wrote:
>
> The size returned by 'getvar partition-size' should be in bytes, not in
> blocks as fastboot uses that value to generate empty partition when
> running format [1].
>
> Note that the function was already returning the proper size in
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> Split out the code that actually boots linux into a separate sub-command.
> Add base_ptr to the state to support this.
>
> Show an error if the boot fails, since this should not happen.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang
Hi Simon,
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> Add a subcommand that sets up the kernel ready for execution.
This commit actually adds 2 subcommands.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no changes since v1)
>
> arch/x86/lib/zimage.c |
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> At present if an error occurs while setting up the boot, interrupts are
> left disabled. Move this call later in the sequence to avoid this problem.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no changes since
This merges the PLIC initialization code from two functions into one.
Signed-off-by: Sean Anderson
---
This patch builds but has NOT been tested.
(no changes since v1)
arch/riscv/lib/andes_plic.c | 58 -
1 file changed, 25 insertions(+), 33 deletions(-)
The riscv-timer driver currently serves as a shim for several riscv timer
drivers. This is not too desirable because it bypasses the usual timer
selection via the driver model. There is no easy way to specify an
alternate timing driver, or have the tick rate depend on the cpu's
configured
This converts the clint driver from the riscv-specific interface to be a
DM-based UCLASS_TIMER driver. We also need to re-add the initialization for
IPI back into the SPL code. This was previously implicitly done when the
timer was initialized. In addition, the SiFive DDR driver previously
Another "virtual" clock (in the sense that it isn't configurable). This
could possibly be done as a clock in the device tree, but I think this is a
bit cleaner.
Signed-off-by: Sean Anderson
---
checkpatch still complains about this one, but I don't see any reason to
break it up even further. It
AFAIK because the K210 clock driver does not come up until after
relocation, the clint will always use the clock-frequency parameter.
Ideally, it should update itself after relocation to take into account the
actual CPU frequency.
The interrupt controller property is removed from the clint
This converts the PLMT driver from the riscv-specific timer interface to be
a DM-based UCLASS_TIMER driver.
The clock-frequency/clocks properties are preferred over timebase-frequency
for two reasons. First, properties which affect a device should be located
near its binding in the device tree.
This series cleans up the timer drivers in RISC-V and converts them to DM.
This series depends on [1]. This series needs to be tested! I have only tested
it on QEMU and the K210. Notably, this means that the HiFive and anything Andes
is completely untested. CI for this series is located at [2].
We may need to add a clock-frequency binding like for the K210.
Signed-off-by: Sean Anderson
---
This patch builds but has NOT been tested.
Changes in v3:
- Rebase
Changes in v2:
- Fix SiFive CLINT not getting tick-rate from rtcclk
arch/riscv/dts/fu540-c000-u-boot.dtsi | 8 ++--
At present if a FIT references a missing external blob, binman reports an
error, even if the image is supposed to allow this.
Propagate this setting down to the child sections of the FIT, so that the
behaviour is consistent.
This is a fix-up patch to:
binman: Build FIT image subentries with
Hello all,
I am using u-boot on a STM32MP1 EV1 board. Until recently, the NAND
DFU backend was used to flash UBI images to the board. I used the
DFU_NAND_TRIMFFS option to ensure that the UBI image was correctly
flashed to NAND.
Recently, ST has switched from the NAND DFU backend to the MTD DFU
Hello all,
I am using u-boot on a STM32MP1 EV1 board. Until recently, the NAND
DFU backend was used to flash UBI images to the board. I used the
DFU_NAND_TRIMFFS option to ensure that the UBI image was correctly
flashed to NAND.
Recently, ST has switched from the NAND DFU backend to the MTD DFU
Hi,
On Fri, 28 Aug 2020 10:44:55 +
Trommel, Kees (Contractor) kees.trommel.contrac...@draeger.com wrote:
> Hi Agust,
>
> The latest version of the U-Boot does not support conversion from
> 24BPP BMP to a 16BPP 565RGB encoded frame buffer. It uses always
> 555RGB encoding (see function
On 01.09.20 13:14, Sean Anderson wrote:
> On 9/1/20 6:51 AM, Heinrich Schuchardt wrote:
>> On 8/18/20 11:00 AM, Heinrich Schuchardt wrote:
>>> On 11.08.20 12:32, Sean Anderson wrote:
On 8/11/20 3:50 AM, Heinrich Schuchardt wrote:
> On 11.08.20 08:20, Rick Chen wrote:
>> Hi Heinrich
Hi Simon,
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> Add subcommands to zboot. At present there is only one called 'start'
> which does the whole boot. It is the default command so is optional.
>
> Change the 's' string variable to const while we are here.
> Signed-off-by: Simon
On Sun, Aug 30, 2020 at 5:45 AM Simon Glass wrote:
>
> A few things have changed since this was written about 18 months ago.
> Update the README.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no changes since v1)
>
> doc/README.chromium | 9 ++---
> 1 file
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> Add a little subcommand that prints out where the kernel was loaded and
> its setup pointer. Run it by default in the normal boot.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no changes since v1)
>
>
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> There is a lot of information in the setup block and it is quite hard to
> decode manually. Add a 'zboot dump' command to decode it into a
> human-readable format.
>
> Signed-off-by: Simon Glass
> Reviewed-by: Wolfgang Wallner
> ---
>
> (no
On Sun, Aug 30, 2020 at 5:44 AM Simon Glass wrote:
>
> Recent versions of Chrome OS do not have a kernel in the root disk, to
> save space.
>
> With the improvements to the 'zboot' command it is fairly easy to load
> the kernel from the raw partition. Add instructions on how to do this.
>
>
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> At present the setup block is always obtained from the image
> automatically. In some cases it can be useful to use a setup block
> obtained elsewhere, e.g. if the image has already been unpacked. Add an
> argument to support this and update
On Sun, Aug 30, 2020 at 5:42 AM Simon Glass wrote:
>
> When booting Chrome OS images the command line is stored separately
> from the kernel. Add a way to specify this address so that images boot
> correctly.
>
> Also add comments to the zimage.h header.
>
> Signed-off-by: Simon Glass
>
Add a new entry argument to the fit entry which allows selection of the
default configuration to use. This is the 'default' property in the
'configurations' node.
Update the Makefile to pass in the value of DEVICE_TREE or
CONFIG_DEFAULT_DEVICE_TREE to provide this information.
Signed-off-by:
In some cases it is useful to generate a FIT which has a number of DTB
images, selectable by configuration. Add support for this in binman,
using a simple iterator and string substitution.
Signed-off-by: Simon Glass
---
Changes in v3:
- Rebase on top of earlier binman series
Changes in v2:
-
At present 64-bit sunxi boards use the Makefile to create a FIT, using
USE_SPL_FIT_GENERATOR. This is deprecated.
Update sunxi to use binman instead.
Signed-off-by: Simon Glass
---
(no changes since v2)
Changes in v2:
- Add a 'fit-fdt-list' property
- Fix 'board' typo in commit message
This file is no-longer used. Drop it.
Signed-off-by: Simon Glass
---
(no changes since v1)
board/sunxi/mksunxi_fit_atf.sh | 87 --
1 file changed, 87 deletions(-)
delete mode 100755 board/sunxi/mksunxi_fit_atf.sh
diff --git a/board/sunxi/mksunxi_fit_atf.sh
Add a special help message pointing to the relevant README.
Signed-off-by: Simon Glass
---
(no changes since v1)
arch/arm/dts/sunxi-u-boot.dtsi | 1 +
tools/binman/missing-blob-help | 4
2 files changed, 5 insertions(+)
diff --git a/arch/arm/dts/sunxi-u-boot.dtsi
When an external blob is missing it can be quite confusing for the user.
Add a way to provide a help message that is shown.
Signed-off-by: Simon Glass
---
Changes in v3:
- Add a way to show help messages for missing blobs
tools/binman/README| 6 ++
Add an entry for ARM Trusted Firmware's 'BL31' payload, which is the
device's main firmware. Typically this is U-Boot.
Signed-off-by: Simon Glass
---
Changes in v3:
- Rebase on top of earlier binman series
Changes in v2:
- Add the URL of ARM Trusted Firmware and mention of U-Boot docs
- Fix
This patch allows uboot scripts make choices about where to boot from based on
the active mmc boot partition. This allows having two copies of kernel,
filesystems etc, and choosing which to boot from based off the active
bootloader partition.
Signed-off-by: Reuben Dowle
---
cmd/mmc.c | 2 ++
Its common to use dt-bindings instead of hard-coding clocks or resets.
So lets use the imported Linux GCC bindings on IPQ40xx target.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
arch/arm/dts/qcom-ipq4019.dtsi| 3 ++-
arch/arm/mach-ipq40xx/clock-ipq4019.c | 4 +++-
2 files changed,
Since we have a driver for the reset controller, lets add the necessary node.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
arch/arm/Kconfig | 1 +
arch/arm/dts/qcom-ipq4019.dtsi | 9 +
2 files changed, 10 insertions(+)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the
reset controller.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
MAINTAINERS | 2 +
drivers/reset/Kconfig
There is already existing driver for SMEM so lets enable it for IPQ40xx as well.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
arch/arm/Kconfig | 2 ++
arch/arm/dts/qcom-ipq4019.dtsi | 5 +
drivers/smem/Kconfig | 2 +-
3 files changed, 8 insertions(+), 1
Import Qualcomm IPQ4019 GCC bindings from Linux.
This will enable using bindings instead of raw clock numbers both in the driver
and DTS like Linux does.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
MAINTAINERS | 1 +
This patch series builds on the previously merged basic
Qualcomm IPQ40xx series support.
Signed-off-by: Robert Marko
Cc: Luka Perkov
Robert Marko (9):
dt-bindings: clock: import Qualcomm IPQ4019 bindings
IPQ40xx: clk: Use dt-bindings instead of hardcoding
IPQ40xx: Add SMEM support
Add driver for Qualcomm DWC3 based dual role xHCI USB controller.
Currently tested on IPQ40xx, but should support other Qualcomm SoC families as
well.
Only host mode is supported.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
MAINTAINERS | 2 +
There are drivers to support built in USB controller and PHY-s now, so lets add
the USB nodes to DTSI.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
arch/arm/dts/qcom-ipq4019.dtsi | 50 ++
1 file changed, 50 insertions(+)
diff --git
PHY handling functions should depend also on CONFIG_USB_DWC3 aka DM DWC3
version.
Otherwise when using the non DM version with PHY subsystem enabled there will
be a linking error due to missing dwc3_setup_phy and dwc3_shutdown_phy.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
Add a driver to setup the USB PHY-s on Qualcomm IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: Robert Marko
Cc: Luka Perkov
---
MAINTAINERS| 1 +
drivers/phy/Kconfig| 6 ++
drivers/phy/Makefile | 1 +
On Tue, Sep 01, 2020 at 10:36:31PM +0800, Bin Meng wrote:
> Hi Tom,
>
> This PR includes the following x86 changes for v2020.10:
>
> - Fix parsing of "mtrr list" command
> - Introduce USE_EARLY_BOARD_INIT option and remove dead codes for most
> x86 boards
>
> Azure results : PASS
>
Hi Michal,
On Tue, 1 Sep 2020 at 09:15, Michal Simek wrote:
>
> Hi Simon,
>
> On 30. 08. 20 22:37, Simon Glass wrote:
> > Hi Michal,
> >
> > On Wed, 26 Aug 2020 at 08:12, Michal Simek wrote:
> >>
> >> Hi,
> >>
> >> On 25. 08. 20 18:57, Simon Glass wrote:
> >>> Hi Michal,
> >>>
> >>> On Tue, 25
Hi Sam,
On Tue, Sep 01, 2020 at 01:31:46PM +0300, Sam Protsenko wrote:
> Hi Gary,
>
> On Thu, 27 Aug 2020 at 11:51, Gary Bisson
> wrote:
> >
> > The size returned by 'getvar partition-size' should be in bytes, not in
> > blocks as fastboot uses that value to generate empty partition when
> >
Hi Daniel,
Hi Stefan,
comments inline below.
Many Thanks
Mauro
On 9/1/20 1:41 AM, Daniel Schwierzeck wrote:
> Am Montag, den 31.08.2020, 23:53 +0200 schrieb Mauro Condarelli:
>> Thanks Daniel.
>>
>> On 8/31/20 10:36 PM, Daniel Schwierzeck wrote:
>>> Hi Mauro,
>>>
>>> Am Montag, den 31.08.2020,
Hi Simon,
On 30. 08. 20 22:37, Simon Glass wrote:
> Hi Michal,
>
> On Wed, 26 Aug 2020 at 08:12, Michal Simek wrote:
>>
>> Hi,
>>
>> On 25. 08. 20 18:57, Simon Glass wrote:
>>> Hi Michal,
>>>
>>> On Tue, 25 Aug 2020 at 09:13, Michal Simek wrote:
Hi Simon,
On 25. 08. 20
Am Dienstag, den 01.09.2020, 15:09 +0200 schrieb Mauro Condarelli:
> Hi Daniel,
> Hi Stefan,
> comments inline below.
>
> Many Thanks
> Mauro
>
> On 9/1/20 1:41 AM, Daniel Schwierzeck wrote:
> > Am Montag, den 31.08.2020, 23:53 +0200 schrieb Mauro Condarelli:
> > > Thanks Daniel.
> > >
> > > On
On Wed, 26 Aug 2020 at 07:34, Michal Simek wrote:
>
> Fix typo.
>
> Fixes: 19790632648b ("binman: Support accessing binman tables at run time")
> Signed-off-by: Michal Simek
> ---
>
> include/binman_sym.h | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
Reviewed-by: Simon Glass
On Mon, 31 Aug 2020 at 03:59, Alper Nebi Yasak wrote:
>
> When reading subentries of each image, the FIT entry type directly
> concatenates their contents without padding them according to their
> offset, size, align, align-size, align-end, pad-before, pad-after
> properties.
>
> This patch makes
On Wed, 26 Aug 2020 at 07:13, Michal Simek wrote:
>
> There is prepared function for filing rom_offset. That's why use it instead
> of copying content of it.
>
> Signed-off-by: Michal Simek
> ---
>
> lib/binman.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
Reviewed-by: Simon Glass
On Mon, 31 Aug 2020 at 03:59, Alper Nebi Yasak wrote:
>
> Switch to str.startswith for matching like the FIT etype does since the
> current version doesn't ignore 'hash-1', 'hash-2', etc.
>
> Signed-off-by: Alper Nebi Yasak
> ---
>
> Changes in v2:
> - Add test to check that sections ignore
Hi Alper,
On Tue, 1 Sep 2020 at 06:23, Alper Nebi Yasak wrote:
>
> On 01/09/2020 13:36, Simon Glass wrote:
> > Hi Alper,
> >
> > I found that evb-rk3288 fails to build with the final patch from your
> > series. See u-boot-dm/testing for the tree.
>
> I had seen your patch and assumed that
1 - 100 of 124 matches
Mail list logo
