Add command "boot_bank X" to switch the boot bank to either
1 or 2.
Signed-off-by: Jagdish Gediya
---
board/freescale/ls1012ardb/ls1012ardb.c | 85 +
1 file changed, 85 insertions(+)
diff --git a/board/freescale/ls1012ardb/ls1012ardb.c
b/board/freescale/ls1012ar
Fix various style violations in elf.h
- use correct comment format if the comment fits in just one line
- remove the ending period for the one-line comment
- use tab for the indention instead of space
- put the opening brace at the same line of a typedef/union
- remove in a 'typedef struct' for co
If CONFIG_FRAMEBUFFER_SET_VESA_MODE is not set, don't switch
graphics card to VESA mode. This applies to both native mode
and emulator mode of running the VGA BIOS.
Signed-off-by: Bin Meng
---
Changes in v2: None
arch/x86/lib/bios.c | 4
drivers/bios_emulator/atibios.c | 4 +++
There is a small duplication in do_bootvx() that does the bootline
copy. Refactor this a little bit to make it simpler.
Signed-off-by: Bin Meng
---
Changes in v2: None
cmd/elf.c | 15 +--
1 file changed, 5 insertions(+), 10 deletions(-)
diff --git a/cmd/elf.c b/cmd/elf.c
index cd9
If video initialization fails, the "Video:" output message will be
mixed with the next console log. Change to print out such message
only when everything is OK, which improves the boot log readability.
Signed-off-by: Bin Meng
---
Changes in v2: None
drivers/pci/pci_rom.c | 4 +---
1 file chang
This adds a very simple ELF64 loader via program headers, similar
to load_elf_image_phdr() that we already have.
Signed-off-by: Bin Meng
---
Changes in v2:
- update the ELF32 and ELF64 loader comments
cmd/elf.c | 44 +++-
1 file changed, 43 insertions(+
This changes 'struct e820entry' to 'struct e820_entry' to conform
with the coding style.
Signed-off-by: Bin Meng
---
Changes in v2: None
arch/x86/cpu/coreboot/sdram.c| 2 +-
arch/x86/cpu/qemu/e820.c | 2 +-
arch/x86/cpu/tangier/sdram.c | 4 ++--
arch/x86/include/asm/bootparam.h
This changes the default FRAMEBUFFER_VESA_MODE to use 32-bit pixel
format for better VxWorks compatibility.
Signed-off-by: Bin Meng
---
Changes in v2: None
drivers/video/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
in
This fixes the following checkpatch warning:
warning: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Bin Meng
---
Changes in v2: None
arch/x86/cpu/coreboot/sdram.c | 7 ---
arch/x86/cpu/qemu/e820.c | 3 ++-
arch/x86/cpu/tangier/sdram.c | 6 --
arch/x86/include/
On VxWorks x86 its bootline address is at a pre-defined offset @
0x1200. If 'bootaddr' is not passed via environment variable, we
assign its value based on the kernel memory base address.
Signed-off-by: Bin Meng
---
Changes in v2: None
cmd/elf.c | 91 +--
This updates the doc of booting VxWorks, like loading an x64 kernel,
and how to make VxWorks graphics console driver work.
Signed-off-by: Bin Meng
---
Changes in v2:
- update the graphics console driver information
doc/README.vxworks | 21 +++--
1 file changed, 19 insertions(+
When booting from EFI BIOS, VxWorks bootloader stores the EFI GOP
framebuffer info at a pre-defined offset @ 0x6100. When VxWorks
kernel boots up, its EFI console driver tries to find such a block
and if the signature matches, the framebuffer information will be
used to initialize the driver.
Howe
This corrects a typo and updates several places for clarity.
Signed-off-by: Bin Meng
Reviewed-by: Christian Gmeiner
---
Changes in v2: None
doc/README.vxworks | 8
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/doc/README.vxworks b/doc/README.vxworks
index 3433e4f..eb1
This adds ELF header, program header and section header structure
defines for the 64-bit ELF image.
Signed-off-by: Bin Meng
---
Changes in v2: None
include/elf.h | 43 +++
1 file changed, 43 insertions(+)
diff --git a/include/elf.h b/include/elf.h
index
This changes 'struct e820info' to 'struct e820_info' to conform
with the coding style.
Signed-off-by: Bin Meng
---
Changes in v2: None
cmd/elf.c | 6 +++---
include/vxworks.h | 2 +-
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/cmd/elf.c b/cmd/elf.c
index 4638d79..071
Exit the 'bootvx' command if bootline address is not specified.
Signed-off-by: Bin Meng
---
Changes in v2: None
cmd/elf.c | 109 ++
1 file changed, 53 insertions(+), 56 deletions(-)
diff --git a/cmd/elf.c b/cmd/elf.c
index 22ff254..0
This changes some boards' default FRAMEBUFFER_VESA_MODE to use 32-bit
pixel format for better VxWorks compatibility.
Signed-off-by: Bin Meng
---
Changes in v2: None
configs/bayleybay_defconfig | 2 +-
configs/minnowmax_defconfig | 2 +-
configs/qemu-x86_64_defconfig
VxWorks bootloader stores its size at a pre-defined offset @ 0x5004.
Later when VxWorks kernel boots up and system memory information is
retrieved from the E820 table, the bootloader size will be subtracted
from the total system memory size to calculate the size of available
memory for the OS.
Exp
At present two environment variables 'e820data'/'e820info' are required
to boot a VxWorks x86 kernel, but this is superfluous. The offset of
these two tables are actually at a fixed offset from the kernel memory
base address and we can provide the kernel memory base address to U-Boot
via only one v
This introduces various enhancements to booting VxWorks x86 kernels.
It also cleans up the 'bootvx' x86 path a little bit.
Test was performed on MinnowMax, with VxWorks 7 generic x86/x64
images, with VGA text mode and EFI graphics mode console drivers.
This series is available at u-boot-x86/bootv
On Tue, Apr 10, 2018 at 10:42:45AM -0400, Simon Glass wrote:
> +U-Boot, Tom, Masahiro
>
> Hi David,
>
> On 10 April 2018 at 01:22, David Gibson wrote:
> > On Wed, Apr 04, 2018 at 01:21:10AM +0800, Simon Glass wrote:
> >> Hi David,
> >>
> >> On 3 April 2018 at 23:02, David Gibson wrote:
> >> >
>
Hi Marcin,
Marcin Niestroj wrote:
Hi Witold,
On 11.04.2018 08:18, sdrb wrote:
Hi,
I use Grinn's chiliSOM and very old U-boot 2014.07 on it.
Unfortunately the newest u-boot doesn't run SPL properly - so I'm
forced to use 2014.07 version.
What are your problems exactly with SPL? What versio
On Tue, Apr 10, 2018 at 06:36:06PM -0400, Tom Rini wrote:
> On Tue, Apr 10, 2018 at 10:42:45AM -0400, Simon Glass wrote:
> > +U-Boot, Tom, Masahiro
> >
> > Hi David,
> >
> > On 10 April 2018 at 01:22, David Gibson wrote:
> > > On Wed, Apr 04, 2018 at 01:21:10AM +0800, Simon Glass wrote:
> > >> H
2018-04-12 12:28 GMT+09:00 Marek Vasut :
> The following changes since commit
> d79dfd4519c3f357a2523acfeb26eca6f59eae4d:
>
>
>
>
>
> spl: ram: Add TPL Kconfig symbols (2018-04-11 13:22:06 -0400)
>
>
>
>
>
> are available in the Git repository at:
>
> git://git.denx.de/u-boot-sh.git master
>
>
The following changes since commit c4446b1d6c96de406972690083e2884bf69bce5c:
Merge git://git.denx.de/u-boot-ubi (2018-04-11 10:05:41 -0400)
are available in the Git repository at:
git://git.denx.de/u-boot-usb.git master
for you to fetch changes up to 2960e27e3834ef2e6d506b21a582bd97ac18bbb0
The following changes since commit
d79dfd4519c3f357a2523acfeb26eca6f59eae4d:
spl: ram: Add TPL Kconfig symbols (2018-04-11 13:22:06 -0400)
are available in the Git repository at:
git://git.denx.de/u-boot-sh.git master
for you to fetch changes up to 97ed677831e45b789fc19bd807273ff344
Hi,
On Thu, 30 Nov 2017 01:25:01 +
Andre Przywara wrote:
> SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
> timer) in U-Boot.
> At the moment it is mandatory for ARMv8 and used by two ARMv7 boards.
> Add a proper Kconfig symbol to express this dependency properly,
> allow
From: Andre Przywara
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable
After commit 46fc679ede5f69 ("arm: timer: get frequency for arch timer
armv7 in cp15 cntfrq") the ARM architected timer driver knows how to
determine the timer frequency at runtime by reading the CNTFRQ register,
so we don't need to hardcode the timer frequency anymore.
Signed-off-by: Tuomas Tynkk
Hello all,
I've been playing around with signed FIT images and I found some unexpected
behavior.
I was hoping to get some input on whether this behaves as expected or whether
there's
an issue that needs resolving.
I have a board where I am attempting to sign both the config and image nodes of
The Gen3 kernel images are often above 8 MiB, increase the
maximum kernel size to 64 MiB to future-proof it, just like
many other ARM64 boards do.
Signed-off-by: Marek Vasut
Cc: Nobuhiro Iwamatsu
---
include/configs/rcar-gen3-common.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/
On Sat, Apr 07, 2018 at 05:03:28PM +0200, Marek Vasut wrote:
> This patch is a preparation for adding TPL support for RAM loading.
> CONFIG_IS_ENABLED allows for proper handling of the U-Boot/SPL/TPL
> differences in config symbol names.
>
> Signed-off-by: Marek Vasut
> Cc: Tom Rini
Applied to
On Sat, Apr 07, 2018 at 05:03:45PM +0200, Marek Vasut wrote:
> Add TPL config symbols for RAM loading matching the SPL ones.
>
> Signed-off-by: Marek Vasut
> Cc: Tom Rini
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: PGP signature
_
On Sat, Apr 07, 2018 at 04:06:22PM +0200, Marek Vasut wrote:
> This patch fixes a situation where CONFIG_DM_SERIAL is enabled for
> regular U-Boot and SPL, but not for TPL. In that case, the build
> will try to include serial-uclass into the TPL nonetheless, because
> CONFIG_DM_SERIAL is set.
>
>
On Sat, Apr 07, 2018 at 04:05:46PM +0200, Marek Vasut wrote:
> Add Kconfig entry for CONFIG_TPL_SPI_LOAD symbol to match the SPL one.
>
> Signed-off-by: Marek Vasut
> Cc: Tom Rini
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: PGP signature
On Sat, Apr 07, 2018 at 04:06:11PM +0200, Marek Vasut wrote:
> Add Kconfig entry for CONFIG_TPL_YMODEM_SUPPORT symbol to match the SPL one.
>
> Signed-off-by: Marek Vasut
> Cc: Tom Rini
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: PGP signature
__
On Sat, Apr 07, 2018 at 04:06:36PM +0200, Marek Vasut wrote:
> The tiny variants of memset and memcpy implementations can be
> built for TPL as well, check whether a TPL build is in progress
> and avoid including the default variants.
>
> Signed-off-by: Marek Vasut
> Cc: Simon Glass
> Cc: Tom R
On Sat, Apr 07, 2018 at 04:05:27PM +0200, Marek Vasut wrote:
> Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
> configurations using it to Kconfig.
>
> Signed-off-by: Marek Vasut
> Cc: Tom Rini
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: PGP signature
On Wed, Apr 11, 2018 at 09:26:40PM +0200, Sjoerd Simons wrote:
> Since commit 8e14ba7bd524 ("gpio: omap_gpio: Add DM_FLAG_PRE_RELOC
> flag") omap GPIO gets bound before relocation. Unfortunately due to
> this, on at least the beaglebone black, the pre-relocation memory pool
> gets exhausted befor
Since commit 8e14ba7bd524 ("gpio: omap_gpio: Add DM_FLAG_PRE_RELOC
flag") omap GPIO gets bound before relocation. Unfortunately due to
this, on at least the beaglebone black, the pre-relocation memory pool
gets exhausted before probing the serial port. This then causes u-boot
to panic as CONFIG_RE
To make it simpler to enable the debug uart on boneblack add debug
uart configuration as an example in the defconfig but with
CONFIG_DEBUG_UART disabled. Which allows a user to simple enable it when
needing easily without figuring out the right values for memory
base/clock and shift.
Signed-off-by
Hello Alexander,
Am 27.03.2018 um 16:52 schrieb Alexander Kochetkov:
The commit implement a gpio-based software deblocking. The code
extract I2C pins description from device tree, switch pins to GPIO
mode, toggle SCL until slave release SDA, send I2C stop and switch
I2C pins back to I2C mode.
S
Hello Mario,
Am 28.03.2018 um 14:37 schrieb Mario Six:
Add an option to get the clock speed from the device tree, hence adding
compatibility with DM clock drivers.
Signed-off-by: Mario Six
---
drivers/i2c/fsl_i2c.c | 8 +++-
1 file changed, 7 insertions(+), 1 deletion(-)
Applied to u-
Hello Alexander,
Am 27.03.2018 um 16:52 schrieb Alexander Kochetkov:
The commit describe usage of gpios and pinctrl device tree
properties in order to enable gpio-based software deblocking.
Signed-off-by: Alexander Kochetkov
---
doc/device-tree-bindings/i2c/i2c.txt | 13 +
1 f
Hello Mario,
Am 28.03.2018 um 14:37 schrieb Mario Six:
Since bus translations are now fully supported, use a plain
"dev_read_addr" to get the device address from the device tree.
Signed-off-by: Mario Six
---
drivers/i2c/fsl_i2c.c | 5 +
1 file changed, 1 insertion(+), 4 deletions(-)
A
Hello Mario,
Am 28.03.2018 um 14:37 schrieb Mario Six:
The fpgamap interface has been switched to a "single function + data
size" interface. Reflect this change in the IHS I2C driver.
Signed-off-by: Mario Six
---
drivers/i2c/ihs_i2c.c | 45 -
1 fi
On 11/04/2018 17:08, Neil Armstrong wrote:
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong
---
drivers/usb/host/Kconfig | 7 +++
drivers/usb/host/Makefile | 1
Hi Witold,
On 11.04.2018 08:18, sdrb wrote:
Hi,
I use Grinn's chiliSOM and very old U-boot 2014.07 on it. Unfortunately
the newest u-boot doesn't run SPL properly - so I'm forced to use
2014.07 version.
What are your problems exactly with SPL? What version of chiliSOM does
you board have? M
On Wed, Apr 11, 2018 at 12:52 PM, Guillaume Gardet
wrote:
> So, how to handle dtb filenames? Update with wrong soc definition ? Or drop
> this patch and define a FDTFILE for each flavor?
You can take a look at how we handle this for wandboard, cuboxi,
sabresd, for example.
Taking mx6sabresd as
From: Stefan Agner
Report correct ECC parameters back to the stack. Do not report
bytes as we have it not immeaditly available and the Linux version
also does not report it. It seems to have no aversive effect.
Signed-off-by: Stefan Agner
---
Changes in v3: None
Changes in v2:
- Extend the pat
From: Stefan Agner
Add support for minimum ECC strength supported by the NAND chip.
This aligns with the behavior when using the fsl,use-minimum-ecc
device tree property in Linux.
Signed-off-by: Stefan Agner
---
Changes in v3: None
Changes in v2: None
drivers/mtd/nand/Kconfig| 8 +
From: Stefan Agner
Add config option which allows to enable on flash bad block table
support. This has the same effect as when using the device tree
property "nand-on-flash-bbt" in Linux.
Signed-off-by: Stefan Agner
---
Changes in v3: None
Changes in v2: None
drivers/mtd/nand/mxs_nand.c | 4
From: Stefan Agner
Calculate BCH geometry at start and store the information in
a structure. This avoids recalculation on every page access
and allows to calculate ECC relevant information in one place.
This patch does not change ECC layout or driver behavior in
any way.
The patch aligns the dri
From: Stefan Agner
Instead of completing initialization via scan_bbt callback use
NAND self init to initialize the GPMI (MXS) NAND controller.
Suggested-by: Scott Wood
Signed-off-by: Stefan Agner
---
Changes in v3:
- Fix indentation
Changes in v2: None
drivers/mtd/nand/Kconfig| 1 +
d
From: Stefan Agner
This patchset reworks the drivers ECC calculation to align more
with the Linux driver gpmi-nand.c. It aims to implements minimal
ECC support as supported by the NAND chip.
This is the rebased version after moving MXS NAND to Kconfig.
--
Stefan
Changes in v3:
- Fix indentatio
Le 11/04/2018 à 17:46, Gary Bisson a écrit :
Hi Guillaume,
On Wed, Apr 11, 2018 at 12:38:48PM +0200, Guillaume GARDET wrote:
Signed-off-by: Guillaume GARDET
Cc: Troy Kisky
Cc: Stefano Babic
Cc: Fabio Estevam
Cc: Gary Bisson
---
arch/arm/mach-imx/mx6/soc.c | 34
Hi Neil,
while trying to test your patches on dwc3, I ran into a compilation issue.
On 03/04/2018 11:40, Neil Armstrong wrote:
This patch adds a "bulk" API to the reset API in order to get/deassert/
assert/release a group of reset signals associated with a device.
This bulk API will avoid addi
Hi Guillaume,
On Wed, Apr 11, 2018 at 12:38:48PM +0200, Guillaume GARDET wrote:
> Signed-off-by: Guillaume GARDET
> Cc: Troy Kisky
> Cc: Stefano Babic
> Cc: Fabio Estevam
> Cc: Gary Bisson
>
> ---
> arch/arm/mach-imx/mx6/soc.c | 34 ++
> 1 file changed, 34 in
The pinctrl bindings has changed for Amlogic Meson SoCs since Linux 4.13,
update the pinctrl driver to take this in account.
Signed-off-by: Neil Armstrong
---
drivers/pinctrl/meson/pinctrl-meson-gxbb.c | 12 ++--
drivers/pinctrl/meson/pinctrl-meson-gxl.c | 14 +++---
2 files cha
On Wed, Apr 11, 2018 at 11:41 AM, Guillaume Gardet
wrote:
> This is for efi fdtfile fallback definition for default distro config for
> nitrogen6x board.
> Is it ok for you?
Yes, this is the explanation that I was looking for :-)
Please send a new version with this info added in the commit log.
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.16.0.
Signed-off-by: Neil Armstrong
---
arch/arm/dts/meson-gx.dtsi| 87 ++-
arch/arm/dts/meson-gxbb-odroidc2.dts | 56 --
arch/arm/dts/meson-gxbb.dtsi |
Synchronize the Amlogic Meson GX Device Tree and bindings with Linux 4.16 to
beneficiate with the new DT nodes.
The pinctrl bindings has changed since 4.13, so the pinctrl driver must be
updated with the changes.
Neil Armstrong (2):
ARM64: meson: Sync DT and Bindings with Linux 4.16
pinctrl:
On 04/11/2018 05:07 PM, Neil Armstrong wrote:
> This patchset adds support for USB for the Amlogic Meson GXL SoCs following
> the work done for Linux by Martin Blumenstingl at [1] [2] [3].
>
> The support consist of :
> - A port of dwc3-of-simple from Linux to U-boot
> - A change to support more
It may be unnecessary to check signature on unlocked board.
Get the hint from platform specific code to support secure boot
and non-secure boot with the same binary, so that boot is not
blocked if board is not locked and has no key for signature
verification.
Signed-off-by: Jun Nie
---
common/im
Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.
Signed-off-by: Neil Armstrong
---
Changes since v1:
- Resent as single patch since cpuinfo needs further work
- Aligned the defines in gx.h
arch/arm/include/asm/arch-meson/gx.h | 70 +++
The Amlogic Meson GXL and GXM (simple variant) embeds up to 3 USB2 PHYs
and an USB3 PHY. This patch adds drivers for these for the standard generic
PHY interface and supports the power-on/off calls and set the Host mode by
default.
They are based on the excellent work from Martin Blumenstingl merge
This patchset adds support for USB for the Amlogic Meson GXL SoCs following
the work done for Linux by Martin Blumenstingl at [1] [2] [3].
The support consist of :
- A port of dwc3-of-simple from Linux to U-boot
- A change to support more than 2 PHYs in the DWC3 DM driver
- An USB2 PHY Driver a
DWC3 Ips can have more than 1 PHY for USB2 and 1 PHY for USB3, add support
for a generic number of PHYs and adapt the code to handle a generic
number of PHYs.
Signed-off-by: Neil Armstrong
---
drivers/usb/host/xhci-dwc3.c | 113 +--
1 file changed, 66 inse
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong
---
drivers/usb/host/Kconfig | 7 +++
drivers/usb/host/Makefile | 1 +
drivers/usb/host/dwc3-of-simple.c | 109 ++
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard
Tested By: Bruno Herrera
---
drivers/clk/clk_stm32f.c | 36 +---
drivers/misc/stm32_rcc.c | 12 +--
From: Stefan Agner
Add writebcb command which creates a NAND Boot Configuration Block
(BCB) at the beginning of the active flash device. The BCB stores
the information for the SoC internal boot ROM where the application
with a valid IVT header can be found on the NAND device. The first
two argume
On 04/11/2018 04:53 PM, Neil Armstrong wrote:
> Hi Marek,
>
> On 11/04/2018 16:37, Marek Vasut wrote:
>> On 04/11/2018 04:29 PM, Neil Armstrong wrote:
>>> This is a port of the dwc3-of-simple driver from Linux to enable/deassert
>>> clock and resets of a simple DWC3 Controller HW glue.
>>>
>>> Sig
Hi Marek,
On 11/04/2018 16:37, Marek Vasut wrote:
> On 04/11/2018 04:29 PM, Neil Armstrong wrote:
>> This is a port of the dwc3-of-simple driver from Linux to enable/deassert
>> clock and resets of a simple DWC3 Controller HW glue.
>>
>> Signed-off-by: Neil Armstrong
>
> Looks good, except can w
Hi Icenowy & Jagan,
I see bananapi zero patch was posted and discussed in [1], but without
further follow up. Maybe we can decide which name is more maintainable
first, bananapi-*, Bananapi-* or Sinovoip_BPI_*. And add all new
boards with following the rule. Which one do you prefer?
If possible,
On Wed, Apr 11, 2018 at 7:55 AM, Alexander Graf wrote:
> On 04/11/2018 02:37 PM, Marek Vasut wrote:
>>
>> On 04/11/2018 02:26 PM, Tom Rini wrote:
>>>
>>> On Wed, Apr 11, 2018 at 10:12:42AM +0200, Marek Vasut wrote:
On 04/11/2018 04:52 AM, Dinh Nguyen wrote:
[...]
u-boo
On 04/11/2018 04:29 PM, Neil Armstrong wrote:
> This is a port of the dwc3-of-simple driver from Linux to enable/deassert
> clock and resets of a simple DWC3 Controller HW glue.
>
> Signed-off-by: Neil Armstrong
Looks good, except can we reduce the number of ifdefs, ie. by using
empty functions
Hi,
Le 11/04/2018 à 16:23, Fabio Estevam a écrit :
Hi Guillaume,
On Wed, Apr 11, 2018 at 7:38 AM, Guillaume GARDET
wrote:
Please explain in the commit log why this is needed. Thanks
This is for efi fdtfile fallback definition for default distro config for
nitrogen6x board.
Is it ok for yo
Hi Jaehoon,
On 10/04/2018 18:01, Heinrich Schuchardt wrote:
> On 03/24/2018 03:57 PM, Heinrich Schuchardt wrote:
>> On 03/18/2018 01:03 AM, Vagrant Cascadian wrote:
>>> On 2018-03-17, Heinrich Schuchardt wrote:
The Odroid C2 fails to read from mmc with U-Boot v2018.03.
The change avoids
The Amlogic Meson GXL and GXM (simple variant) embeds up to 3 USB2 PHYs
and an USB3 PHY. This patch adds drivers for these for the standard generic
PHY interface and supports the power-on/off calls and set the Host mode by
default.
They are based on the excellent work from Martin Blumenstingl merge
DWC3 Ips can have more than 1 PHY for USB2 and 1 PHY for USB3, add support
for a generic number of PHYs and adapt the code to handle a generic
number of PHYs.
Signed-off-by: Neil Armstrong
---
drivers/usb/host/xhci-dwc3.c | 113 +--
1 file changed, 66 inse
This patchset adds support for USB for the Amlogic Meson GXL SoCs following
the work done for Linux by Martin Blumenstingl at [1] [2] [3].
The support consist of :
- A port of dwc3-of-simple from Linux to U-boot
- A change to support more than 2 PHYs in the DWC3 DM driver
- An USB2 PHY Driver a
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong
---
drivers/usb/host/Kconfig | 7 +++
drivers/usb/host/Makefile | 1 +
drivers/usb/host/dwc3-of-simple.c | 123 ++
Hi Guillaume,
On Wed, Apr 11, 2018 at 7:38 AM, Guillaume GARDET
wrote:
Please explain in the commit log why this is needed. Thanks
> Signed-off-by: Guillaume GARDET
> Cc: Troy Kisky
> Cc: Stefano Babic
> Cc: Fabio Estevam
> Cc: Gary Bisson
___
U-
Hi,
I use Grinn's chiliSOM and very old U-boot 2014.07 on it. Unfortunately
the newest u-boot doesn't run SPL properly - so I'm forced to use
2014.07 version.
I noticed that there is some problem with USB maintenance. As far as I
know the chiliSOM is TI AM335x compatible system so it uses Me
Boards have an option to rewrite variable locations in their own board
files. This is necessary for qspi and nand configurations where boot
image can be bigger then 896k(current limit).
Signed-off-by: Michal Simek
---
include/configs/zynq-common.h | 8 ++--
1 file changed, 6 insertions(+),
There is no need to use zynq name as SYS_BOARD for all boards.
The patch is adding an option to change it.
Signed-off-by: Michal Simek
---
arch/arm/mach-zynq/Kconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/mach-zynq/Kconfig b/arch/arm/mach-zynq/Kconfig
index 87729047f999..1
When static memory configuration is used U-Boot has capability to detect
memory size in setup range. Enable this feature for static
configuration.
Signed-off-by: Michal Simek
---
board/xilinx/zynq/board.c| 3 ++-
board/xilinx/zynqmp/zynqmp.c | 3 ++-
2 files changed, 4 insertions(+), 2 dele
On Tue, Apr 03, 2018 at 11:44:18AM +0200, Neil Armstrong wrote:
> This patch adds a "bulk" API to the clock API in order to get/enable/disable
> /release a group of clocks associated with a device.
>
> This bulk API will avoid adding a copy of the same code to manage
> a group of clocks in driver
On Mon, Apr 02, 2018 at 02:42:53AM -0600, Simon Glass wrote:
> Without the units these numbers are confusing. Add a comment about the
> unit being 'bytes' and mention 'buildman' as the source.
>
> Suggested-by: Lukasz Majewski
> Signed-off-by: Simon Glass
Applied to u-boot/master, thanks!
--
On Tue, Apr 03, 2018 at 11:44:19AM +0200, Neil Armstrong wrote:
> This patch adds the bulk clock API tests for the sandbox test suite.
>
> It's very similar to the main test but only uses the _bulk() API and
> checks if the clocks are correctly enabled/disabled.
>
> Signed-off-by: Neil Armstrong
On Wed, Apr 04, 2018 at 03:39:20PM +0200, Heinrich Schuchardt wrote:
> Update scripts/checkpatch.pl from upstream.
>
> One of the many corrections is not creating an error for cover-letters.
>
> Reintroduce U-Boot's
> 5c761ce58666b3a1695697498598f8bf3484a0c7
> checkpatch.pl: Add warning for new
On Wed, Apr 04, 2018 at 01:16:08AM +0200, Heinrich Schuchardt wrote:
> Provide correct file paths.
>
> Signed-off-by: Heinrich Schuchardt
> Reviewed-by: Patrick Delaunay
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: PGP signature
__
On Wed, Apr 04, 2018 at 01:54:26AM +0200, Heinrich Schuchardt wrote:
> The most significant change is the addition of the --self-test option
> which allows to run a consistency check on all MAINTAINERS files.
>
> Signed-off-by: Heinrich Schuchardt
Applied to u-boot/master, thanks!
--
Tom
si
On Tue, Apr 03, 2018 at 11:40:51AM +0200, Neil Armstrong wrote:
> This patch adds the bulk reset API tests for the sandbox test suite.
>
> Unlike the main test, it also check the "other" reset signal using the bulk
> API
> and checks if the resets are correctly asserted/deasserted.
>
> To allow
On Wed, Apr 11, 2018 at 03:16:21PM +0200, Heiko Schocher wrote:
> Hello Tom,
>
> please pull from u-boot-ubi master
>
> The following changes since commit 2600df4f8ef12ece9cec13030005919e0ba2b0d5:
>
> Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblaze
> (2018-04-09 11:
On Fri, Mar 30, 2018 at 10:28:19AM +0200, Guillaume GARDET wrote:
> Commit 253c60a breaks the exit value of 'mkimage -T rkimage'
> and print the following error:
> mkimage: Can't print header for Rockchip Boot Image support: Success
>
> It is not a failure to not print headers, so just display
On Wed, Apr 04, 2018 at 10:09:57AM +0200, Kristian Amlie wrote:
> Using sizeof gives the size of the pointer only, not the string. This
> could easily lead to crashes when using -l argument.
>
> Signed-off-by: Kristian Amlie
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description
On Fri, Mar 30, 2018 at 09:22:40AM +0200, Patrice Chotard wrote:
> Similarly to ARMV7, on ARMV7M instruction cache memory needs
> to be disabled before running linux kernel to avoid kernel to
> be stuck.
>
> Signed-off-by: Patrice Chotard
Applied to u-boot/master, thanks!
--
Tom
signature.a
On Thu, Mar 29, 2018 at 02:55:25PM +0200, Neil Armstrong wrote:
> The Amlogic Meson SoCs embeds up to 256 reset lines, add the corresponding
> driver.
>
> Signed-off-by: Neil Armstrong
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: PGP signature
On Tue, Apr 03, 2018 at 11:40:50AM +0200, Neil Armstrong wrote:
> This patch adds a "bulk" API to the reset API in order to get/deassert/
> assert/release a group of reset signals associated with a device.
>
> This bulk API will avoid adding a copy of the same code to manage
> a group of reset si
1 - 100 of 139 matches
Mail list logo