Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delau...@st.com>
---
arch/arm/dts/stm32mp157.dtsi | 28 +++++++++++
arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi | 21 ++++++++
arch/arm/dts/stm32mp157c-ed1.dts | 37 ++++++++++++++
board/st/stm32mp1/README | 83 +++++++++++++++++++++++---------
configs/stm32mp15_basic_defconfig | 1 +
include/configs/stm32mp1.h | 1 +
6 files changed, 147 insertions(+), 24 deletions(-)
diff --git a/arch/arm/dts/stm32mp157.dtsi b/arch/arm/dts/stm32mp157.dtsi
index 32d3984..77953c8 100644
--- a/arch/arm/dts/stm32mp157.dtsi
+++ b/arch/arm/dts/stm32mp157.dtsi
@@ -86,6 +86,20 @@
status = "disabled";
};
+ sdmmc3: sdmmc@48004000 {
+ compatible = "st,stm32-sdmmc2";
+ reg = <0x48004000 0x400>, <0x48005000 0x400>;
+ reg-names = "sdmmc", "delay";
+ interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>;
+ clocks = <&rcc_clk SDMMC3_K>;
+ resets = <&rcc_rst SDMMC3_R>;
+ st,idma = <1>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <120000000>;
+ status = "disabled";
+ };
+
rcc: rcc@50000000 {
compatible = "syscon", "simple-mfd";
@@ -288,6 +302,20 @@
status = "disabled";
};
+ sdmmc2: sdmmc@58007000 {
+ compatible = "st,stm32-sdmmc2";
+ reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
+ reg-names = "sdmmc", "delay";
+ interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>;
+ clocks = <&rcc_clk SDMMC2_K>;
+ resets = <&rcc_rst SDMMC2_R>;
+ st,idma = <1>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <120000000>;
+ status = "disabled";
+ };
+
i2c4: i2c@5c002000 {
compatible = "st,stm32f7-i2c";
reg = <0x5c002000 0x400>;
diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
index 94d27fb..5d43753 100644
--- a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
@@ -11,6 +11,7 @@
/ {
aliases {
mmc0 = &sdmmc1;
+ mmc1 = &sdmmc2;
i2c3 = &i2c4;
};
};
@@ -77,6 +78,7 @@
CLK_SDMMC12_PLL3R
CLK_I2C46_PCLK5
CLK_I2C12_PCLK1
+ CLK_SDMMC3_PLL3R
CLK_I2C35_PCLK1
CLK_UART1_PCLK5
CLK_UART24_PCLK1
@@ -131,3 +133,22 @@
&sdmmc1 {
u-boot,dm-spl;
};
+
+/* MMC2 boot */
+&sdmmc2_b4_pins_a {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc2_d47_pins_a {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc2 {
+ u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
index 4b20fab..129cd02 100644
--- a/arch/arm/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/dts/stm32mp157c-ed1.dts
@@ -112,6 +112,31 @@
bias-pull-up;
};
};
+ sdmmc2_b4_pins_a: sdmmc2-b4@0 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+ <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+ <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+ <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+ <STM32_PINMUX('E', 3, AF9)>, /* SDMMC2_CK */
+ <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
+
+ sdmmc2_d47_pins_a: sdmmc2-d47@0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+ <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+ <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+ <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
};
&pinctrl_z {
@@ -160,6 +185,18 @@
status = "okay";
};
+&sdmmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,dirpol;
+ st,negedge;
+ bus-width = <8>;
+ status = "okay";
+};
+
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
diff --git a/board/st/stm32mp1/README b/board/st/stm32mp1/README
index 4adc978..42a39d0 100644
--- a/board/st/stm32mp1/README
+++ b/board/st/stm32mp1/README
@@ -115,7 +115,31 @@ the supported device trees for stm32mp157 are:
+ FSBL = spl/u-boot-spl.stm32
+ SSBL = u-boot.img
-6. Prepare an SDCard
+6. Switch Setting for Boot Mode
+===============================
+
+You can select the boot mode, on the board ed1 with the switch SW1
+
+ -----------------------------------
+ Boot Mode BOOT2 BOOT1 BOOT0
+ -----------------------------------
+ Reserved 0 0 0
+ NOR 0 0 1
+ SD-Card 1 1 1
+ SD-Card 1 0 1
+ eMMC 0 1 0
+ NAND 0 1 1
+ Recovery 1 1 0
+ Recovery 0 0 0
+
+Recovery is a boot from serial link (UART/USB) and it is used with
+STM32CubeProgrammer tool to load executable in RAM and to update the flash
+devices available on the board (NOR/NAND/eMMC/SDCARD).
+The communication between HOST and board is based on
+- for UARTs : the uart protocol used with all MCU STM32
+- for USB : based on USB DFU 1.1 (without the ST extensions used on MCU STM32)
+
+7. Prepare an SDCard
===================
The minimal requirements for STMP32MP1 boot up to U-Boot are:
@@ -147,13 +171,13 @@ for example: with gpt table with 128 entries
# sgdisk -o /dev/<SDCard dev>
b) create minimal image
- # sgdisk --resize-table=128 -a 1 \
+ # sgdisk --resize-table=128 -a 1 \
-n 1:34:545 -c 1:fsbl1 \
-n 2:546:1057 -c 2:fsbl2 \
-n 3:1058:5153 -c 3:ssbl \
-p /dev/<SDCard dev>
- you can add other partition for kernel (rootfs)
+ you can add other partition for kernel (rootfs for example)
c) copy the FSBL (2 times) and SSBL file on the correct partition.
in this example in partition 1 to 3
@@ -163,29 +187,40 @@ for example: with gpt table with 128 entries
# dd if=u-boot-spl.stm32 of=/dev/mmcblk0p2
# dd if=u-boot.img of=/dev/mmcblk0p3
-7. Switch Setting
-==================
-
-You can select the boot mode, on the board ed1 with the switch SW1
+To boot from SDCard, select BootPinMode = 1 1 1 and reset.
- -----------------------------------
- Boot Mode BOOT2 BOOT1 BOOT0
- -----------------------------------
- Reserved 0 0 0
- NOR 0 0 1
- SD-Card 1 1 1
- SD-Card 1 0 1
- eMMC 0 1 0
- NAND 0 1 1
- Recovery 1 1 0
- Recovery 0 0 0
+8. Prepare eMMC
+===============
+You can use U-Boot to copy binary in eMMC.
+In the next example, you need to boot from SDCARD and the images
(u-boot-spl.stm32, u-boot.img)
+are presents on SDCARD (mmc 0) in ext4 partition 4 (bootfs).
To boot from SDCard, select BootPinMode = 1 1 1 and reset.
-Recovery is a boot from serial link (UART/USB) and it is used with
-STM32CubeProgrammer tool to load executable in RAM and to update the flash
-devices available on the board (NOR/NAND/eMMC/SDCARD).
-The communication between HOST and board is based on
-- for UARTs : the uart protocol used with all MCU STM32
-- for USB : based on USB DFU 1.1 (without the ST extensions used on MCU STM32)
+Then you update the eMMC with the next U-Boot command :
+
+a) prepare GPT on eMMC,
+ example with 2 partitions, bootfs and roots:
+
+ # setenv emmc_part
"name=ssbl,size=2MiB;name=bootfs,type=linux,bootable,size=64MiB;name=rootfs,type=linux,size=512"
+ # gpt write mmc 1 ${emmc_part}
+
+b) copy SPL on eMMC on firts boot partition
+ (SPL max size is 256kB, with LBA 512, 0x200)
+
+ # ext4load mmc 0:4 0xC0000000 u-boot-spl.stm32
+ # mmc dev 1
+ # mmc partconf 1 1 1 1
+ # mmc write ${fileaddr} 0 200
+ # mmc partconf 1 1 1 0
+
+b) copy U-Boot in first GPT partition of eMMC
+
+ # ext4load mmc 0:4 0xC0000000 u-boot.img
+ # mmc dev 1
+ # part start mmc 1 1 partstart
+ # part size mmc 1 1 partsize
+ # mmc write ${fileaddr} ${partstart} ${partsize}
+
+To boot from eMMC, select BootPinMode = 0 1 0 and reset.
diff --git a/configs/stm32mp15_basic_defconfig
b/configs/stm32mp15_basic_defconfig
index 4ab1d4c..0f5950f 100644
--- a/configs/stm32mp15_basic_defconfig
+++ b/configs/stm32mp15_basic_defconfig
@@ -19,6 +19,7 @@ CONFIG_SYS_PROMPT="STM32MP> "
# CONFIG_CMD_IMPORTENV is not set
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PMIC=y
diff --git a/include/configs/stm32mp1.h b/include/configs/stm32mp1.h
index aae2cb8..6281dd5 100644
--- a/include/configs/stm32mp1.h
+++ b/include/configs/stm32mp1.h
@@ -71,6 +71,7 @@
/*MMC SD*/
#define CONFIG_SYS_MMC_MAX_DEVICE 3
+#define CONFIG_SUPPORT_EMMC_BOOT
#if !defined(CONFIG_SPL) || !defined(CONFIG_SPL_BUILD)
--
2.7.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
