Re: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support
Hi, On 10/09/2014 06:37 PM, Jagan Teki wrote: > Hi Peng Fan, > > Before reviewing these two patches, I'm requesting some sort work from > your side like > Can you update/fix the driver "drivers/spi/fsl_qspi.c" without using > flash opcodes. > > Using flash opcode's with in the (q)spi driver is not recommended > please think on that > direction. Yeah, many OPCODE_XX are used in this driver. There is a LUT table containing 16 entries in the QSPI Controller. The Look-up-table or LUT consists of a number of pre-programmed sequences. Each sequence is basically a sequence of instruction-operand pairs which when executed sequentially generates a valid serial flash transaction. Each sequence can have a maximum of 8 instruction-operand pairs. The instruction holds the flash opcode that should be pre-programmed, and the qspi_set_lut in drivers/spi/fsl_qspi.c does this work. It is not easy to program the lut dynamically in the driver without using the flash opcodes. So I wonder whether CMD_xxx in drivers/mtd/spi/sf_internal.h can be used or not. Or, can QSPI_CMD_xxx be used but not OPCODE_xx? Actually if QSPI_CMD_xx can be used, the value QSPI_CMD_xx is the same with OPCODE_xx, just different macro names. Regards, Peng. > > On 9 October 2014 14:37, Peng Fan wrote: >> >> Hi, >> >> Any reply about this patch? It is long time since this patch was sent out. >> >> Regards, >> Peng. >> On 09/11/2014 10:30 AM, Fan Peng-B51431 wrote: >>> Just CC Stefano Babic >>> >>> Regards, >>> Peng. >>> >>> -Original Message- >>> From: u-boot-boun...@lists.denx.de [mailto:u-boot-boun...@lists.denx.de] On >>> Behalf Of Peng Fan >>> Sent: Thursday, September 11, 2014 9:56 AM >>> To: Estevam Fabio-R49496; Li Ye-B37916 >>> Cc: u-boot@lists.denx.de >>> Subject: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support >>> >>> Configure the pad setting and enable qspi clock to support qspi flashes >>> access. >>> >>> This patch has been tested on mx6sxsabresd board. >>> >>> Signed-off-by: Peng Fan >>> --- >>> >>> Changelog v2: >>> Take Fabio's suggestion, split soc code and board code into two patches. >>> This patch needs 'ARM:MX6SX Add QSPI support' patch. >>> >>> board/freescale/mx6sxsabresd/mx6sxsabresd.c | 40 >>> + >>> include/configs/mx6sxsabresd.h | 14 ++ >>> 2 files changed, 54 insertions(+) >>> >>> diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c >>> b/board/freescale/mx6sxsabresd/mx6sxsabresd.c >>> index 5eaec1b..f9cad5a 100644 >>> --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c >>> +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c >>> @@ -272,11 +272,51 @@ int board_mmc_init(bd_t *bis) >>> return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); } >>> >>> +#ifdef CONFIG_FSL_QSPI >>> + >>> +#define QSPI_PAD_CTRL1 \ >>> + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ >>> + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) >>> + >>> +static iomux_v3_cfg_t const quadspi_pads[] = { >>> + MX6_PAD_NAND_WP_B__QSPI2_A_DATA_0 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_READY_B__QSPI2_A_DATA_1| >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_CE0_B__QSPI2_A_DATA_2 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_CE1_B__QSPI2_A_DATA_3 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_ALE__QSPI2_A_SS0_B | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_CLE__QSPI2_A_SCLK | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_DATA07__QSPI2_A_DQS| >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_DATA01__QSPI2_B_DATA_0 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_DATA00__QSPI2_B_DATA_1 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_WE_B__QSPI2_B_DATA_2 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_RE_B__QSPI2_B_DATA_3 | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_DATA03__QSPI2_B_SS0_B | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_DATA02__QSPI2_B_SCLK | >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> + MX6_PAD_NAND_DATA05__QSPI2_B_DQS| >>> MUX_PAD_CTRL(QSPI_PAD_CTRL1), >>> +}; >>> + >>> +int board_qspi_init(void) >>> +{ >>> + /* Set the iomux */ >>> + imx_iomux_v3_setup_multiple_pads(quadspi_pads, >>> + ARRAY_SIZE(quadspi_pads)); >>> + >>> + /* Set the clock */ >>> + enable_qspi_clk(1); >>> + >>> + return 0; >>> +} >>> +#endif >>> + >>> int board_init(void) >>> { >>> /* Address of boot parameters */ >>> gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; >>> >>> +#ifdef CONFIG_FSL_QSPI >>> + board_qspi_init(); >>> +#endif >>> + >>> return 0; >>> } >>> >>> diff --git a/include/configs/mx6sxsabresd.h >>> b/include/configs/mx6sxsabresd.h index 1eda65e..00031ec 100644 >>> --- a/include/configs/mx6sxsabresd.h >>> +++ b/include/configs/mx6s
Re: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support
Hi Peng Fan, Before reviewing these two patches, I'm requesting some sort work from your side like Can you update/fix the driver "drivers/spi/fsl_qspi.c" without using flash opcodes. Using flash opcode's with in the (q)spi driver is not recommended please think on that direction. On 9 October 2014 14:37, Peng Fan wrote: > > Hi, > > Any reply about this patch? It is long time since this patch was sent out. > > Regards, > Peng. > On 09/11/2014 10:30 AM, Fan Peng-B51431 wrote: >> Just CC Stefano Babic >> >> Regards, >> Peng. >> >> -Original Message- >> From: u-boot-boun...@lists.denx.de [mailto:u-boot-boun...@lists.denx.de] On >> Behalf Of Peng Fan >> Sent: Thursday, September 11, 2014 9:56 AM >> To: Estevam Fabio-R49496; Li Ye-B37916 >> Cc: u-boot@lists.denx.de >> Subject: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support >> >> Configure the pad setting and enable qspi clock to support qspi flashes >> access. >> >> This patch has been tested on mx6sxsabresd board. >> >> Signed-off-by: Peng Fan >> --- >> >> Changelog v2: >> Take Fabio's suggestion, split soc code and board code into two patches. >> This patch needs 'ARM:MX6SX Add QSPI support' patch. >> >> board/freescale/mx6sxsabresd/mx6sxsabresd.c | 40 >> + >> include/configs/mx6sxsabresd.h | 14 ++ >> 2 files changed, 54 insertions(+) >> >> diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c >> b/board/freescale/mx6sxsabresd/mx6sxsabresd.c >> index 5eaec1b..f9cad5a 100644 >> --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c >> +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c >> @@ -272,11 +272,51 @@ int board_mmc_init(bd_t *bis) >> return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); } >> >> +#ifdef CONFIG_FSL_QSPI >> + >> +#define QSPI_PAD_CTRL1 \ >> + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ >> + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) >> + >> +static iomux_v3_cfg_t const quadspi_pads[] = { >> + MX6_PAD_NAND_WP_B__QSPI2_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_READY_B__QSPI2_A_DATA_1| MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_CE0_B__QSPI2_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_CE1_B__QSPI2_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_ALE__QSPI2_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_CLE__QSPI2_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_DATA07__QSPI2_A_DQS| MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_DATA01__QSPI2_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_DATA00__QSPI2_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_WE_B__QSPI2_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_RE_B__QSPI2_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_DATA03__QSPI2_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_DATA02__QSPI2_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> + MX6_PAD_NAND_DATA05__QSPI2_B_DQS| MUX_PAD_CTRL(QSPI_PAD_CTRL1), >> +}; >> + >> +int board_qspi_init(void) >> +{ >> + /* Set the iomux */ >> + imx_iomux_v3_setup_multiple_pads(quadspi_pads, >> + ARRAY_SIZE(quadspi_pads)); >> + >> + /* Set the clock */ >> + enable_qspi_clk(1); >> + >> + return 0; >> +} >> +#endif >> + >> int board_init(void) >> { >> /* Address of boot parameters */ >> gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; >> >> +#ifdef CONFIG_FSL_QSPI >> + board_qspi_init(); >> +#endif >> + >> return 0; >> } >> >> diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h >> index 1eda65e..00031ec 100644 >> --- a/include/configs/mx6sxsabresd.h >> +++ b/include/configs/mx6sxsabresd.h >> @@ -201,6 +201,20 @@ >> /* FLASH and environment organization */ #define CONFIG_SYS_NO_FLASH >> >> +#define CONFIG_FSL_QSPI >> + >> +#ifdef CONFIG_FSL_QSPI >> +#define CONFIG_CMD_SF >> +#define CONFIG_SPI_FLASH >> +#define CONFIG_SPI_FLASH_SPANSION >> +#define CONFIG_SPI_FLASH_STMICRO >> +#define CONFIG_SYS_FSL_QSPI_LE >> +#define CONFIG_QSPI_BASE QSPI2_BASE_ADDR >> +#define CONFIG_QSPI_MEMMAP_BASE QSPI2_ARB_BASE_ADDR >> +#define FSL_QSPI_FLASH_SIZE SZ_16M >> +#define FSL_QSPI_FLASH_NUM 2 >> +#endif >> + >> #define CONFIG_ENV_OFFSET(6 * SZ_64K) >> #define CONFIG_ENV_SIZE SZ_8K >> #define CONFIG_ENV_IS_IN_MMC >> -- >> 1.8.4 thanks! -- Jagan. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support
Hi, Any reply about this patch? It is long time since this patch was sent out. Regards, Peng. On 09/11/2014 10:30 AM, Fan Peng-B51431 wrote: > Just CC Stefano Babic > > Regards, > Peng. > > -Original Message- > From: u-boot-boun...@lists.denx.de [mailto:u-boot-boun...@lists.denx.de] On > Behalf Of Peng Fan > Sent: Thursday, September 11, 2014 9:56 AM > To: Estevam Fabio-R49496; Li Ye-B37916 > Cc: u-boot@lists.denx.de > Subject: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support > > Configure the pad setting and enable qspi clock to support qspi flashes > access. > > This patch has been tested on mx6sxsabresd board. > > Signed-off-by: Peng Fan > --- > > Changelog v2: > Take Fabio's suggestion, split soc code and board code into two patches. > This patch needs 'ARM:MX6SX Add QSPI support' patch. > > board/freescale/mx6sxsabresd/mx6sxsabresd.c | 40 > + > include/configs/mx6sxsabresd.h | 14 ++ > 2 files changed, 54 insertions(+) > > diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c > b/board/freescale/mx6sxsabresd/mx6sxsabresd.c > index 5eaec1b..f9cad5a 100644 > --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c > +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c > @@ -272,11 +272,51 @@ int board_mmc_init(bd_t *bis) > return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); } > > +#ifdef CONFIG_FSL_QSPI > + > +#define QSPI_PAD_CTRL1 \ > + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ > + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) > + > +static iomux_v3_cfg_t const quadspi_pads[] = { > + MX6_PAD_NAND_WP_B__QSPI2_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_READY_B__QSPI2_A_DATA_1| MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_CE0_B__QSPI2_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_CE1_B__QSPI2_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_ALE__QSPI2_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_CLE__QSPI2_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_DATA07__QSPI2_A_DQS| MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_DATA01__QSPI2_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_DATA00__QSPI2_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_WE_B__QSPI2_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_RE_B__QSPI2_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_DATA03__QSPI2_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_DATA02__QSPI2_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_NAND_DATA05__QSPI2_B_DQS| MUX_PAD_CTRL(QSPI_PAD_CTRL1), > +}; > + > +int board_qspi_init(void) > +{ > + /* Set the iomux */ > + imx_iomux_v3_setup_multiple_pads(quadspi_pads, > + ARRAY_SIZE(quadspi_pads)); > + > + /* Set the clock */ > + enable_qspi_clk(1); > + > + return 0; > +} > +#endif > + > int board_init(void) > { > /* Address of boot parameters */ > gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; > > +#ifdef CONFIG_FSL_QSPI > + board_qspi_init(); > +#endif > + > return 0; > } > > diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h > index 1eda65e..00031ec 100644 > --- a/include/configs/mx6sxsabresd.h > +++ b/include/configs/mx6sxsabresd.h > @@ -201,6 +201,20 @@ > /* FLASH and environment organization */ #define CONFIG_SYS_NO_FLASH > > +#define CONFIG_FSL_QSPI > + > +#ifdef CONFIG_FSL_QSPI > +#define CONFIG_CMD_SF > +#define CONFIG_SPI_FLASH > +#define CONFIG_SPI_FLASH_SPANSION > +#define CONFIG_SPI_FLASH_STMICRO > +#define CONFIG_SYS_FSL_QSPI_LE > +#define CONFIG_QSPI_BASE QSPI2_BASE_ADDR > +#define CONFIG_QSPI_MEMMAP_BASE QSPI2_ARB_BASE_ADDR > +#define FSL_QSPI_FLASH_SIZE SZ_16M > +#define FSL_QSPI_FLASH_NUM 2 > +#endif > + > #define CONFIG_ENV_OFFSET(6 * SZ_64K) > #define CONFIG_ENV_SIZE SZ_8K > #define CONFIG_ENV_IS_IN_MMC > -- > 1.8.4 > > > ___ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot > ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support
Just CC Stefano Babic Regards, Peng. -Original Message- From: u-boot-boun...@lists.denx.de [mailto:u-boot-boun...@lists.denx.de] On Behalf Of Peng Fan Sent: Thursday, September 11, 2014 9:56 AM To: Estevam Fabio-R49496; Li Ye-B37916 Cc: u-boot@lists.denx.de Subject: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support Configure the pad setting and enable qspi clock to support qspi flashes access. This patch has been tested on mx6sxsabresd board. Signed-off-by: Peng Fan --- Changelog v2: Take Fabio's suggestion, split soc code and board code into two patches. This patch needs 'ARM:MX6SX Add QSPI support' patch. board/freescale/mx6sxsabresd/mx6sxsabresd.c | 40 + include/configs/mx6sxsabresd.h | 14 ++ 2 files changed, 54 insertions(+) diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index 5eaec1b..f9cad5a 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -272,11 +272,51 @@ int board_mmc_init(bd_t *bis) return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); } +#ifdef CONFIG_FSL_QSPI + +#define QSPI_PAD_CTRL1 \ + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ +PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) + +static iomux_v3_cfg_t const quadspi_pads[] = { + MX6_PAD_NAND_WP_B__QSPI2_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_READY_B__QSPI2_A_DATA_1| MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_CE0_B__QSPI2_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_CE1_B__QSPI2_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_ALE__QSPI2_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_CLE__QSPI2_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_DATA07__QSPI2_A_DQS| MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_DATA01__QSPI2_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_DATA00__QSPI2_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_WE_B__QSPI2_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_RE_B__QSPI2_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_DATA03__QSPI2_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_DATA02__QSPI2_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_NAND_DATA05__QSPI2_B_DQS| MUX_PAD_CTRL(QSPI_PAD_CTRL1), +}; + +int board_qspi_init(void) +{ + /* Set the iomux */ + imx_iomux_v3_setup_multiple_pads(quadspi_pads, +ARRAY_SIZE(quadspi_pads)); + + /* Set the clock */ + enable_qspi_clk(1); + + return 0; +} +#endif + int board_init(void) { /* Address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; +#ifdef CONFIG_FSL_QSPI + board_qspi_init(); +#endif + return 0; } diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h index 1eda65e..00031ec 100644 --- a/include/configs/mx6sxsabresd.h +++ b/include/configs/mx6sxsabresd.h @@ -201,6 +201,20 @@ /* FLASH and environment organization */ #define CONFIG_SYS_NO_FLASH +#define CONFIG_FSL_QSPI + +#ifdef CONFIG_FSL_QSPI +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SYS_FSL_QSPI_LE +#define CONFIG_QSPI_BASE QSPI2_BASE_ADDR +#define CONFIG_QSPI_MEMMAP_BASEQSPI2_ARB_BASE_ADDR +#define FSL_QSPI_FLASH_SIZESZ_16M +#define FSL_QSPI_FLASH_NUM 2 +#endif + #define CONFIG_ENV_OFFSET (6 * SZ_64K) #define CONFIG_ENV_SIZESZ_8K #define CONFIG_ENV_IS_IN_MMC -- 1.8.4 ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot