paul- wrote:
> What version Synoligy Software are you running, I'll check my setup
> tonight.
I run DSM 6.2-23739. I am able to mount the partition manually with the
following command:
sudo mount -v -t nfs -o addr=NAS_IP,nolock, NAS_IP:/volume1/music
/mnt/NAS
But as you can see, I need the
jmlaniel wrote:
> I don't see the tool tip that you are mentioning... Are you running
> 3.5.0?
>
> In that case, how am I supposed to enter the full path for my shared NFS
> folder? Synology does not let me access volume1.
>
> Thanks for your time!
What version Synoligy Software are you
ian_heys wrote:
> I installed this yesterday. I think there was a capitalisation issue in
> the automatic assignment of the device name on the squeezelite settings
> page.
>
> Working name in my config is:
>
> sysdefault:CARD=IQAudIODigi
>
> Thanks again for this great system.
Thanks for
jmlaniel wrote:
> I don't see the tool tip that you are mentioning... Are you running
> 3.5.0?
>
> In that case, how am I supposed to enter the full path for my shared NFS
> folder? Synology does not let me access volume1.
>
> Thanks for your time!
Yes, 3.5.0 on all Pi's.
I can't really
kidstypike wrote:
> Well the tooltip says no "/".
>
> 25361
I don't see the tool tip that you are mentioning... Are you running
3.5.0?
In that case, how am I supposed to enter the full path for my shared NFS
folder? Synology does not let me access volume1.
Thanks for your time!
jmlaniel wrote:
> This does not help. The problem seems to be with the html interface.
> When I input my share name "volume1/music", the interface prevent me
> from activating the "Set NET mount" button and gives me the "Match the
> requested format".
>
> When I try the CIFS, the script does
kidstypike wrote:
> Possibly - see the _*Notes*_ in the first post in this thread, and my
> post #6.
This does not help. The problem seems to be with the html interface.
When I input my share name "volume1/music", the interface prevent me
from activating the "Set NET mount" button and gives me
jmlaniel wrote:
> I am trying to mount a NFS share on my Synology NAS and all I get in the
> Share Name box is "Match the requested format".
>
> The folder I am trying to mount is in "volume1/music" so I put
> "volume1/music" in the Share Name box. I am currently using version
> 3.5.0. In
I am trying to mount a NFS share on my Synology NAS and all I get in the
Share Name box is "Match the requested format".
The folder I am trying to mount is in "volume1/music" so I put
"volume1/music" in the Share Name box. I am currently using version
3.5.0. In older version, I did not have
I installed this yesterday. I think there was a capitalisation issue in
the automatic assignment of the device name on the squeezelite settings
page.
Working name in my config is:
sysdefault:CARD=IQAudIODigi
Thanks again for this great system.
*Music Store & VPN Server: *Synology DS215J
kidstypike wrote:
> Well I'm fairly certain that if you click the "Beta" tab, and heed the
> fearsome warning, you'll see what I'm seeing in my screenshot :rolleyes:
At one stage the [Resize FS] was in [Beta] and it could destroy the SD
Card, hence the warning.
> Why there's a need for so
Beta mode used to stand for anything that modified the contents of the
card, but as we have added so much, it has become less relevant.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
Please 'donate'
cramcram wrote:
> No, advanced tab
Well I'm fairly certain that if you click the "Beta" tab, and heed the
fearsome warning, you'll see what I'm seeing in my screenshot :rolleyes:
Why there's a need for so many different tabs along the bottom,
completely baffles me :(
*Study/Server - LMS
kidstypike wrote:
> Have you selected the "Beta" tab?
>
> 25342
No, advanced tab
cramcram's Profile: http://forums.slimdevices.com/member.php?userid=22906
View this thread:
cramcram wrote:
> Nope. The feature in the web interface just doesn't work here. I'm only
> getting this and nothing more:
>
> Brand new install without any tinkering around. Tried Firefox and
> Chrome, so shouldn't be a frontend issue.
Have you selected the "Beta" tab?
25342
kidstypike wrote:
> When I click on the "LMS update" button I get feedback as in picture
> below. Maybe try clicking it again just out of curiosity?
Nope. The feature in the web interface just doesn't work here. I'm only
getting this and nothing more:
25326
Brand new install without any
kidstypike wrote:
> Maybe one day someone will see a need to change line 5 :(
>
Well then we would also have to change the title to the document
too.lol. As we transition to our new site, the instructions will
need to change a little bit.I'll catch it then.
piCorePlayer a small
cramcram wrote:
> Did that, works like a charm. Thank you! It would be good to give some
> user-feedback in the web-interface on the LMS page such as "no udpate
> available" or similar...
Maybe one day someone will see a need to change line 5 :(
When I click on the "LMS update" button I get
kidstypike wrote:
> Yes, but change 7.9.1 to 7.9.*2* in line 5 >, $ sudo ./lms-update.sh
> --mm 7.9.1 -s -r -u
Did that, works like a charm. Thank you! It would be good to give some
user-feedback in the web-interface on the LMS page such as "no udpate
available" or similar...
cramcram wrote:
>
>
> How can I update picoreplayer to the latest nightly build? Are these
> instructions still valid?
>
> http://picoreplayer.sourceforge.net/how_to_upgrade_lms.shtml
Yes, but change 7.9.1 to 7.9.*2* in line 5 >, $ sudo ./lms-update.sh
--mm 7.9.1 -s -r -u
*Study/Server
I'm new to picoreplayer and I'm trying to update LMS to the latest
nightly build. If I click on the update LMS button nothing actually
happens, all I'm getting is this screen:
25326
How can I update picoreplayer to the latest nightly build? Are these
instructions still valid?
Thanks for the reply Paul.
I right clicked the drive and didn't see an "eject" option so you are
right I just yanked it.
I f first you don't succeed...
Thanks for all your help!
(1) Pi 3 w/ HifiBerry Digi + Pro & piCorePlayer 3.5.0 LMS 7.9.2, (1)
Touch, (1) Transporter
when working with disks, you have to use the safe removal tool. In the
windows task bar.
Just do what it says, put the drive back on your Windows machine and
repair the disk, then be sure to remove it properly before unplugging.
piCorePlayer a small player for the Raspberry Pi in RAM.
Hi Paul,
Thanks for your help on my old drive. You were right about the network
drive it started giving me the same problem.
So I went out & bought a new drive and formatted it and loaded my
music files on my Windows 10 machine and it mounted fine on pCP.
But to be sure I ran dmesg and it says
Just uninstall shariport-sync.
For shairport-sync to work, you need to put in the appropriate mixer
control. Which for the Justboom amp, is "Digital" (Without the
quotes) Not sure why it's blanked out
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage:
Paul thank you for your reply.
Annoyingly, the PCP is still trying to announce it self directly on
Airplay (not via LMS) . an uninvited guest to a party! And it would
be nice to get rid of it and just use the LMS. How do I turn it off?
Since it tells me that Shairport is not running I am
If you are running the Shairtunes plugin to LMS, then do not run
Shairport-sync.
Shairtunes will announce the name that is set on the squeezelite tab.
Shairport-sync can be used in an environment without LMS
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage:
Pi3B+
piCorePlayer v3.5.0
Just Boom Amp HAT
B passive speakers
Ethernet only connection (wifi turned off)
ALSA 10 band equaliser on
Thank you to everybody for this community. Works like a charm; picked up
straightaway by LMS and have used ShairTunes2(fork) to relay as Airplay
target "Kitchen".
cramcram wrote:
> Trying to setup PiCorePlayer for the first time as LMS server. I'm not
> getting far, I can't download LMS:
>
> >
Code:
> > [ ERROR ] There was a error downloading slimserver.tcz.
> >
>
> My internet connection is fine. I tried
Trying to setup PiCorePlayer for the first time as LMS server. I'm not
getting far, I can't download LMS:
Code:
[ ERROR ] There was a error downloading slimserver.tcz.
My internet connection is fine. I tried 10 hours ago and now, same
result.
Squeezelite runs fine on a pi/piCorePlayer with Bluetooth as audio
output.
I have attached USB dongles for both wireless and bluetooth, both
built-in wireless and bluetooth are switched off.
25315
25316
25317
+---+
|Filename:
Greg Erskine wrote:
>
> So, can you show a screen shot of your Static IP page.
>
Hi Greg, I am continually being assigned 192.168.1.10 upon reboot, every
time! Have tried setting static IP to various numbers in the range that
are unused. My usual address has been 192.168.1.20 and have been
The Bluetooth works fine with a speaker..the speaker must be paired
and connected for squeezelite to run.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
Please 'donate'
Hi David,
I assume you are using the Static IP web page.
If you are not getting the right IP address (after a reboot) then
something is setting it for you. The only thing I can think of that
would do this is DHCP. What is the IP address DHCP assigns you?
So, can you show a screen shot of your
DavidBulluss wrote:
> Hi Paul, thanks for that. When I had bluetooth switched on it was paired
> with a Bose mini-link speaker, and connected to it. Because Squeezelite
> wouldn't start I switched bluetooth off, but Sqlite will still not
> start. Needless to say, cold restart after each change.
paul- wrote:
> David,
>
> When using Bluetooth, it is completely normal for squeezelite not to
> run. The speaker has to be paired and connected for squeezelite to run
> properly. The speaker connect daemon that runs will automatically
> restart squeezelite once a speaker connects.
>
>
David,
When using Bluetooth, it is completely normal for squeezelite not to
run. The speaker has to be paired and connected for squeezelite to run
properly. The speaker connect daemon that runs will automatically
restart squeezelite once a speaker connects.
Not sure about your IP problem.
My rPi3 is running pCP 3.5.0 and LMS n7.9.2, connected by LAN to my
computer for GUI and to server hard drive by USB. I have DCHP turned off
and a fixed IP address for the rPi. Have had no network issues until
today when I attempted to start Squeezelite and use bluetooth connection
to a
paul- wrote:
> To expand on Jeffs answer.
>
> It is the -G option in squeezelite. It can be set on the Squeezlite
> page. It will toggle based on the state of the player Power button.
> The powersave pluginis for LMS and will automatically turn off the
> player power if it is idle for
To expand on Jeffs answer.
It is the -G option in squeezelite. It can be set on the Squeezlite
page. It will toggle based on the state of the player Power button.
The powersave pluginis for LMS and will automatically turn off the
player power if it is idle for a set table amount of
wtnh wrote:
> Does anyone know of a script which will toggle a GPIO pin when the
> Jivelite screen saver goes active? Alternatively, when sleep kicks in
> would also be useful.
>
> I am interested in this because I want to control a LiPo battery charger
> and have it automatically switch to
Does anyone know of a script which will toggle a GPIO pin when the
Jivelite screen saver goes active? Alternatively, when sleep kicks in
would also be useful.
I am interested in this because I want to control a LiPo battery charger
and have it automatically switch to charge mode when the player
Man in a van wrote:
> Oh well, that's me told off and no mistake:(:o
>
> I'm off to the naughty step (on the shady side )
>
> Ronnie
Or You could LMGTFY google translate
:o
rPi 3 + rasPi 7" LCD + HiFiBerry DiGi+ | rPi 2 + IQaudio DAC+ |rPi 2 +
HiFiBerry DAC+ | Squeeze Box Touch | LMS +
I've just set up my first PiCorePlayer. Fantastic work on the software
and user GUI (donation made!). Using 3.5 and a rPi 3B+ (with built in
wifi) and hifiberry DAC + Pro and attached WD 4TB USB drive. Using it as
both LMS (nomysqueezebox start mode) and a player.
I'm going to be using this in
Oh well, that's me told off and no mistake:(:o
I'm off to the naughty step (on the shady side )
Ronnie
Man in a van's Profile: http://forums.slimdevices.com/member.php?userid=43627
View this thread:
Yes, it is really easy cool to consider people with commiseration when
they are trying to understand things in english language and when it is
not their mother language.
I've found the way to make 2 software players in the same PiCore player,
thanks a lot for the help.
Also, it is very easy to
man in a van wrote:
> like jeff says
>
> http://bfy.tw/iws7
>
> :rolleyes::p:)
>
> it's all this sunshine boss:( doin me ed in
>
> ronnir
:d
*Players:* SliMP3,Squeezebox3 x3,Receiver,SqueezeLiteX,PiCorePlayer
x3,Wandboard
*Server:* LMS Version: Latest Nightly on Centos 7 VM on ESXi
renaud wrote:
> Well, thank you for PicorePlayer, it is really wonderful.
> This morning I was changing the settings to go from M2Tech HiFace USB
> output to a simple Ti PCM5102 DAC. And I wondered myself: is it possible
> to have 2 SqueezLite with different parameters running in the same time
garym wrote:
> by the way. bought this via Amazon (US). Perfect little case and easy to
> install.
Glad you like it. :)
*Study/Server - LMS 7.9.2 -* Pi3B+/pCP 3.5.0/pi screen/HiFiBerry
DAC+/jivelite, 25K library and playlists on WDMyCloud, LMS cache on a
USB stick (formatted ntfs).
*Lounge*
renaud wrote:
> Well, thank you for PicorePlayer, it is really wonderful.
> This morning I was changing the settings to go from M2Tech HiFace USB
> output to a simple Ti PCM5102 DAC. And I wondered myself: is it possible
> to have 2 SqueezLite with different parameters running in the same time
Well, thank you for PicorePlayer, it is really wonderful.
This morning I was changing the settings to go from M2Tech HiFace USB
output to a simple Ti PCM5102 DAC. And I wondered myself: is it possible
to have 2 SqueezLite with different parameters running in the same time
?
Really, is it
kidstypike wrote:
> Hi Gary,
>
> If you're using a HiFiBerry DAC, have you looked at their cases? The all
> steel one is nice, it's weighty, and it stays put!
>
> There may be a reseller near you.
>
>
The pi boots in performance mode to speed up boot time, then after
startup switches to powersave (Or whatever you have set on the tweaks
page). It cuts a good 5 seconds off of boot time, but indeed does push
a poor power supply (Or cable with too thin of conductors)
piCorePlayer a small
paul- wrote:
> The undervoltage conditions have not changed. What changed is that it
> is now reported in the kernel log. Previously it would only be shown as
> a lightning bolt if there was a display connected. You should take a
> hard look at how you are powering the system.
>
> Thanks
The undervoltage conditions have not changed. What changed is that it
is now reported in the kernel log. Previously it would only be shown as
a lightning bolt if there was a display connected. You should take a
hard look at how you are powering the system.
Thanks for the comments on the
Not sure if we are tracking successful updates (or just problematic
ones), but I had no problem with this config going from 3.22 to 3.5.0:
Raspberry Pi 3B (not +)
Allo I2S isolator
Allo Boss (old version)
Audio Kernel
Official RPi touch display
LMS (yes I know - not recommended with the Audio
hi mcduman,
There is no fixed date for the next release. Hopefully it will come
together easily, there have been lots of changes.
I am sure we will let you know when it is released. :D
regards
Greg
Greg Erskine's
paul- wrote:
> Appreciate the comments ajuster. Feel free to drop me a PM with your
> thoughts.
>
> As for #2, we have completely reworked wifi for the next release.
i just got a second pi 3b+ and it sounds significantly better than the
3b. may be its because the additional shield on the cpu
Appreciate the comments ajuster. Feel free to drop me a PM with your
thoughts.
As for #2, we have completely reworked wifi for the next release.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
Please 'donate'
pavowren wrote:
> i just came from using max2play and happy with pCP with its simplicity
> and built-in support for Squeezelite.
> unfortunately, my 5" touch-screen is not quite right in terms of touch
> accuracy.
> it was fine on max2play with following entries in config.txt.
>
> hdmi_group=2
Man in a van wrote:
> I think that the standard version of pCP is generally considered to be
> best for a LMS and Player combination.
>
Indeed, avoid the problems with the real time kernel, and use the
regular PCP first.
Upgrade too the Audio Enthusiast version later when you know what you
I think that the standard version of pCP is generally considered to be
best for a LMS and Player combination.
Why not give that a try?
Also, this note from the first post on this thread may (or maybe not)
have some bearing.
> Notes:
> Kernel's in the 4.14.y and newer have increased the
It happens Bencat, great that it is working. Thanks for following up.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
Please 'donate'
Apologies for the below I took a break both to write this post and to
have drink and a think . If everything is the same and the other unit
works there must be something different about that unit . Yes there is
the Digi Hat . The Hifi Berry Pi Hat works mounted to the case door
which covers the
bencat wrote:
> I have already completed one SBt replacment player using the above but
> with Pi HAt Digi and this worked well first time . I have now decided to
> construct a second . Construction and set up seemed to go well system
> boots but having a little number of issues . Firstly each
I have already completed one SBt replacment player using the above but
with Pi HAt Digi . Construction and set up seemed to go well system
boots but having a little number of issues . Firstly each time I turn on
the set up Language Screen and then the Image Choice keeps showing and
will not save
Wigster wrote:
> Hi,
>
> Not sure how to start debugging this, so I thought I would start here.
>
> *Server:* latest LMS 7.9.2 on Windows Server 2012R2 with a bunch of
> plugins.
> *Players:* mix of PCP 3.5.0 RPi's with HiFiBerry DAC/Digi boards
>
> *Problem:* sometimes (not that frequently,
Hi,
Not sure how to start debugging this, so I thought I would start here.
*Server:* latest LMS 7.9.2 on Windows Server 2012R2 with a bunch of
plugins.
*Players:* mix of PCP 3.5.0 RPi's with HiFiBerry DAC/Digi boards
*Problem:* sometimes (not that frequently, so this is hard to track
down)
paul- wrote:
>
> Are you aware of this plugin
> https://forums.slimdevices.com/showthread.php?106289-announce-ShairTunes2W-Airtunes-on-LMS-(forked-version-with-Windows-support)
>
> It works much better with LMS.
Thanks Paul. I installed this plugin and it "just worked" perfectly!
Thanks
paul- wrote:
> With reference to the jivelite autostart button
>
> https://forums.slimdevices.com/showthread.php?108852-Announce-piCorePlayer-3-5-0=910047=1#post910047
hotfix is failing:
[ INFO ] Internet accessible.
[ OK ] Free space: 7035443k - Required space: 15k
[ INFO ] Downloading
With reference to the jivelite autostart button
https://forums.slimdevices.com/showthread.php?108852-Announce-piCorePlayer-3-5-0=910047=1#post910047
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
Please 'donate'
paul- wrote:
> The rpi 7" display works out of the box with pCP/jivelite
>
> Sounds like you just need new calibration data.Quite a few have
> setup other screens..take a look here
>
>
The rpi 7" display works out of the box with pCP/jivelite
Sounds like you just need new calibration data.Quite a few have
setup other screens..take a look here
https://forums.slimdevices.com/showthread.php?107366-picoreplayer-3-11-waveshare-3-5-TFT-jivelite-Raspberry-Pi-2B
pavowren wrote:
> i just came from using max2play and happy with pCP with its simplicity
> and built-in support for Squeezelite.
> unfortunately, my 5" touch-screen is not quite right in terms of touch
> accuracy.
> it was fine on max2play with following entries in config.txt.
>
> hdmi_group=2
i just came from using max2play and happy with pCP with its simplicity
and built-in support for Squeezelite.
unfortunately, my 5" touch-screen is not quite right in terms of touch
accuracy.
it was fine on max2play with following entries in config.txt.
hdmi_group=2
hdmi_mode=87
hdmi_cvt 800
paul- wrote:
> If you are using the pCP device as the LMS server, it is best to do a
> shutdown or halt. The only reason it should be done, is that LMS
> updates it cache files.
>
> There is a shutdown button on the web interface for pcp This can
> also be done from a shell with the
Hi Paul-
Yup, Script was on all my Pcp's
Modified as per your post seems to work fine !
Code:
tc@piCorePlayer:~$ /home/tc/pcp-powerbutton.sh -i 5 -o 6 --low --debug
piCorePlayer Power button shutdown script starting...
Asserting pins :
ShutDown : GPIO5=in,
Was the script on your system? I just realized that the input --low
option didn't work for a push button. It was originally setup for the
audiophonics board. Using inputs as low is much safer..less chance
of connecting voltage to the wrong pin.
So here is the fixed script.
Code:
Hi Paul-
Thanks for that !
> (Pardon the crude sketch) I know Doc you did'nt have time to paint or scale
> it :) (Back To The
Future 3)
Jeff
*Players:* SliMP3,Squeezebox3 x3,Receiver,SqueezeLiteX,PiCorePlayer
x3,Wandboard
*Server:* LMS Version: Latest Nightly on Centos 7 VM on ESXi
Take a look in the home directory, there should be a script called
pcp-powerbutton.sh
Connect a button to any GPIO pin, but GPIO 17 is default
(Pardon the crude sketch)
25223
Then put this command on the tweaks page. Full usage of the command is
in the script.
25224
> You could connect a button on GPIO to do this too.
Out of interest is there a thread on how to do this ?
Hopefilly not as complex as the Audiophonics way
Jeff
*Players:* SliMP3,Squeezebox3 x3,Receiver,SqueezeLiteX,PiCorePlayer
x3,Wandboard
*Server:* LMS Version: Latest Nightly on
If you are using the pCP device as the LMS server, it is best to do a
shutdown or halt. The only reason it should be done, is that LMS
updates it cache files.
There is a shutdown button on the web interface for pcp This can
also be done from a shell with the command "pcp sd"
You could
kidstypike wrote:
> Hi Gary,
>
> If you're using a HiFiBerry DAC, have you looked at their cases? The all
> steel one is nice, it's weighty, and it stays put!
>
> There may be a reseller near you.
>
>
garym wrote:
> Case to hold rPi 3B+ and hifiberry DAC+ Pro
>
> I'm finally putting one of these together to serve as both LMS Server
> (music on attached USB drive) and a Player via analog output. I've
> searched several threads but can't find any recommendations on a CASE to
> hold these.
I know one can simply power-off the rPi running picoreplayer. But I'll
be using it as an LMS Server with attached USB drive holding files.
Typically one has to "eject" the USB drive before removing power. Best
practices on how to handle this (or is it even needed)? Thanks.
*Home:*
rores wrote:
> Hi Paul, i just try it again in chrome browser instead of IE and now ist
> ok :cool:
> Thx for this great software and for your help
That helps alot. I've recently found some javascript code that runs on
everything but IE. I'll recheck before the next release.
piCorePlayer
Hi Paul, i just try it again in chrome browser instead of IE and now ist
ok :cool:
Thx for this great software and for your help
rores's Profile: http://forums.slimdevices.com/member.php?userid=67948
View this thread:
rores,
Make sure you don't have spaces in the mount path. Spaces in the remote
share name is ok. Otherwise, would you mind taking a screen shot of you
screen, just before you press the submit button.
I have tested setups with 4-5 mounts, so there has to be something odd
with your setup.
Hello, im not able to add a second nfs network share in the LMS section
"Setup Network Disk Mount".
One nfs share is working fine, but when i try to add an second one i get
this message:
Write to mount
[ERROR] Web Page Error, No MountType Submitted
after pressing the button "Set Net Mount".
Ist
ralphy wrote:
> We have updated the squeezelite package in the 3.5.0 repository to
> version 1.9.0-1105.
>
> It includes the removal of the hardcoded 5 minute GPIO and power script
> power off from Jeff07971 and a fix for the libmad mp3 decoder forbidden
> bitrate frame memory corruption and
I just re-imaged my pCP boxes with the 3.5 release. I had been on a
rev. 2 version for the last couple years. All went well but I can't
seem to get the shairport feature to turn on. It just shows a red
checkmark. Shairport worked fine prior. I've tried disabling and
re-enabling the feature
We have updated the squeezelite package in the 3.5.0 repository to
version 1.9.0-1105.
It includes the removal of the hardcoded 5 minute GPIO and power script
power off from Jeff07971 and a fix for the libmad mp3 decoder forbidden
bitrate frame memory corruption and eventual crash reported by
phildefer wrote:
> hi all,
>
> For the developper of piCorePlayer :
> thirst thank you for this very great software
>
> If i remenber piCorePlayer doesn't work with special characters in WIFI
> SSID and Password (FAQ number 4)
> here is my little Patch to deal with SSID or Password with "&"
next release
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
Please 'donate'
(https://www.paypal.com/cgi-bin/webscr?cmd=_donations=U7JHY5WYHCNRU=GB_code=USD=PP%2dDonationsBF%3abtn_donateCC_LG%2egif%3aNonHosted)
if you like
phildefer wrote:
> hi all,
>
> here is my little Patch to deal with SSID or Password with "&"
> character
>
> Could you check, and if is Ok for you, could you add this little code in
> your next release
We have already addressed it, you will be able to use almost any
character you want.
paul- wrote:
> I need to fix the beta mode thing.your not the first person hung up
> on that. What I find on bluetooth, is that sometimes you need to power
> both devices down.Start the pCP device, then start the speaker once
> the system begins to boot. Then check for the other
I have no idea what or how you are doing it foxsam. This is really off
topic for this thread. I would make a new thread for yourself,
explaining in detail what you are doing.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://sites.google.com/site/picoreplayer/home
paul- wrote:
> For what it is worth, the jsonrpc interface is quite a bit faster.
> ...
> In the next release of pCP, we have converted most of our builtin
> commands to use this interface.
When I used the jsonrpc PLAYERNAME power off command the player keeps
playing but in the web-interface
paul- wrote:
> Nickdanp,
>
> You are missing pressing the install button on on the card control page
Hi Paul,
D'oh - many thanks. As you can probably guess, I never thought
to switch the Beta tab on! All set up and paired, although no audio
output (but definitely paired and everything running
Liffy99,
Which Edimax device are you using? Some of them are a bit finicky and
the do use slot of power.
Please go to the diagnostics page on the pCP device and look at the
dmesg section. Look for voltage warnings.
Paul
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage:
101 - 200 of 541 matches
Mail list logo
