[ClusterLabs] Pacemaker starts with error on LVM resource

ils as it dose not find the DRBD disk. Any ideas on how to fix this ? Best regards Octavian Ciobanu ___ Users mailing list: Users@clusterlabs.org http://lists.clusterlabs.org/mailman/listinfo/users Project Home: http://www.clusterlabs.org Getting started: h

Re: [ClusterLabs] IP clone issue

> wrote: > I never tried to set an virtual ip in one interfaces without ip, because > the vip is a secondary ip that switch between nodes, not primary ip > > 2017-09-05 15:41 GMT+02:00 Octavian Ciobanu <coctavian1...@gmail.com>: > >> Hello all, >> >> I've e

[ClusterLabs] IP clone issue

erIP:1(ocf::heartbeat:IPaddr2):Stopped When the IP is active on both nodes the services are accessible so there is not an issue with the fact that the interface dose not have an IP allocated at boot. The gateway is set with another pcs command and it is working. Thank in advance for any info.

Re: [ClusterLabs] Resources are stopped and started when one node rejoins

Yes. I've removed ordered="true" from DLM resource and also added collocation constraints for Mount clones with both DLM and iSCSI. On Thu, Aug 31, 2017 at 3:34 PM, Vladislav Bogdanov <bub...@hoster-ok.com> wrote: > 31.08.2017 14:53, Octavian Ciobanu wrote: > >>

Re: [ClusterLabs] Resources are stopped and started when one node rejoins

it when it starts ? or a way to make it keep it's active allocation forcing the rejoining node to look for another unoccupied journal without pushing away the nodes that occupy the journal it allocates for the node that rejoins? Best regards On Mon, Aug 28, 2017 at 6:04 PM, Octavian Ciobanu

Re: [ClusterLabs] Resources are stopped and started when one node rejoins

you again for the help. On Mon, Aug 28, 2017 at 3:53 PM, Vladislav Bogdanov <bub...@hoster-ok.com> wrote: > 28.08.2017 14:03, Octavian Ciobanu wrote: > >> Hey Vladislav, >> >> Thank you for the info. I've tried you suggestions but the behavior is >> still the same. When a

Re: [ClusterLabs] Resources are stopped and started when one node rejoins

. Once again thank you for info. Best regards. Octavian Ciobanu On Sat, Aug 26, 2017 at 8:17 PM, Vladislav Bogdanov <bub...@hoster-ok.com> wrote: > 26.08.2017 19:36, Octavian Ciobanu wrote: > >> Thank you for your reply. >> >> There is no reason to set location for t

Re: [ClusterLabs] Pacemaker not starting ISCSI LUNs and Targets

use only one portal in my cluster configuration. This line I've found while I was searching to fix the same issue as you had. Best regards Octavian Ciobanu On Sat, Aug 26, 2017 at 6:25 PM, John Keates <j...@keates.nl> wrote: > Hey Octavian, > > I did that too, and it worked. Afterwar

Re: [ClusterLabs] Resources are stopped and started when one node rejoins

configured to use vmware esxi. Best regards Octavian Ciobanu On Sat, Aug 26, 2017 at 6:16 PM, John Keates <j...@keates.nl> wrote: > While I am by no means a CRM/Pacemaker expert, I only see the resource > primitives and the order constraints. Wouldn’t you need location and/or > col

Re: [ClusterLabs] Pacemaker not starting ISCSI LUNs and Targets

arget to be created if already exists. I hope this workaround will help you with your issue until a valid solution is available. Best regards Octavian Ciobanu On Tue, Aug 22, 2017 at 12:19 AM, John Keates <j...@keates.nl> wrote: > Hi, > > I have a strange issue where LIO-T based ISC

[ClusterLabs] Resources are stopped and started when one node rejoins

clone pcs constraint order DLM-clone then iSCSI3-clone pcs constraint order iSCSI1-clone then Mount1-clone pcs constraint order iSCSI2-clone then Mount2-clone pcs constraint order iSCSI3-clone then Mount3-clone If I issue the command "pcs cluster standby node1" or "pcs cluster st

Re: [ClusterLabs] Antw: fence_vmware_soap: reads VM status but fails to reboot/on/off

> The same phenomenon also occurs in connection with virsh. > > - https://communities.vmware.com/thread/542433 > > Best Regards, > Hideo Yamauchi. > - Original Message - > >From: Octavian Ciobanu <coctavian1...@gmail.com> > >To: Cluster Labs - All

Re: [ClusterLabs] Antw: fence_vmware_soap: reads VM status but fails to reboot/on/off

Hey Marek, I've run the command with --action off and uploaded the file on one of our servers : https://cloud.iwgate.com/index.php/s/1SpZlG8mBSR1dNE Interesting thing is that at the end of the file I found "Unable to connect/login to fencing device" instead of "Failed: Timed out waiting to power

Re: [ClusterLabs] Antw: fence_vmware_soap: reads VM status but fails to reboot/on/off

UUID" but the comand for power is not there. Regards Octavian On Aug 1, 2017 9:12 AM, "Ulrich Windl" <ulrich.wi...@rz.uni-regensburg.de> wrote: >>> Octavian Ciobanu <coctavian1...@gmail.com> schrieb am 31.07.2017 um 20:16 in Nachricht

[ClusterLabs] fence_vmware_soap: reads VM status but fails to reboot/on/off

Hello, Before I implement the cluster I'm testing the fence agents and I got stuck at the rebooting the VMware based VMs. I have installed VMware ESXi 6.5 Hypervisor with 5 VMs. If I call : # fence_vmware_soap --ssl --ip esxi_ip --username root --password pass --action list I get the list