Re: [one-users] Automatic recover from hardware failure
Hi, I experience this issue with my production environment. The issue was OpenNebula network setting was reset (network down few minutes) therefore ONE think that all the node is offline / error. As we set “redeploy” when host is in error, ONE initiate the redeployment. The moment ONE’s network is up, cause intermittent network issue and read-only mode on the VMs. So, hope this will be addressed in the new solution as well. -- Regards, Anandharaj From: Users [mailto:users-boun...@lists.opennebula.org] On Behalf Of Robert Foote Sent: Monday, September 01, 2014 11:50 PM To: 'Carlos Martín Sánchez'; 'Sander Klein' Cc: 'users' Subject: Re: [one-users] Automatic recover from hardware failure I hope this particular feature is coming soon, as this is a standard ‘cloud’ feature for High Availability, and automatic failover. Robert Foote bpsNode www.bpsnode.comhttp://www.bpsnode.com From: Users [mailto:users-boun...@lists.opennebula.org] On Behalf Of Carlos Martín Sánchez Sent: Monday, September 01, 2014 10:46 AM To: Sander Klein Cc: users Subject: Re: [one-users] Automatic recover from hardware failure Hi, On Thu, Aug 14, 2014 at 8:36 PM, Sander Klein roe...@roedie.nlmailto:roe...@roedie.nl wrote: The delete-recreate action will create a new VM from the original template. This means that the VM will have a new ID, IP, and clean disks. We are working on a new mechanism for hosts with shared storage, to migrate the failed VM to a new host keeping the current IPs, disk state, etc. Is there an ETA on this new mechanism? I just ran into the same problem today in my test setup. I can't say when it will be ready. It's not a patch that you can apply, the changes are made in the core and the scheduler, so you will need to wait for the next OpenNebula release. Regards. -- Carlos Martín, MSc Project Engineer OpenNebula - Flexible Enterprise Cloud Made Simple www.OpenNebula.orghttp://www.opennebula.org/ | cmar...@opennebula.orgmailto:cmar...@opennebula.org | @OpenNebulahttp://twitter.com/opennebula [http://static.avast.com/emails/avast-mail-stamp.png]http://www.avast.com/ This email is free from viruses and malware because avast! Antivirushttp://www.avast.com/ protection is active. DISCLAIMER: This e-mail (including any attachments) is for the addressee(s) only and may be confidential, especially as regards personal data. If you are not the intended recipient, please note that any dealing, review, distribution, printing, copying or use of this e-mail is strictly prohibited. If you have received this email in error, please notify the sender immediately and delete the original message (including any attachments). MIMOS Berhad is a research and development institution under the purview of the Malaysian Ministry of Science, Technology and Innovation. Opinions, conclusions and other information in this e-mail that do not relate to the official business of MIMOS Berhad and/or its subsidiaries shall be understood as neither given nor endorsed by MIMOS Berhad and/or its subsidiaries and neither MIMOS Berhad nor its subsidiaries accepts responsibility for the same. All liability arising from or in connection with computer viruses and/or corrupted e-mails is excluded to the fullest extent permitted by law. -- - - DISCLAIMER: This e-mail (including any attachments) is for the addressee(s) only and may contain confidential information. If you are not the intended recipient, please note that any dealing, review, distribution, printing, copying or use of this e-mail is strictly prohibited. If you have received this email in error, please notify the sender immediately and delete the original message. MIMOS Berhad is a research and development institution under the purview of the Malaysian Ministry of Science, Technology and Innovation. Opinions, conclusions and other information in this e- mail that do not relate to the official business of MIMOS Berhad and/or its subsidiaries shall be understood as neither given nor endorsed by MIMOS Berhad and/or its subsidiaries and neither MIMOS Berhad nor its subsidiaries accepts responsibility for the same. All liability arising from or in connection with computer viruses and/or corrupted e-mails is excluded to the fullest extent permitted by law. ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
Re: [one-users] Softlayer Error
Dear Vicenzo, How is the SoftLayer plugin evaluation going? We are very interested in receiving feedback about this feature introduced in OpenNebula 4.8. Thanks in advance, -Tino -- OpenNebula - Flexible Enterprise Cloud Made Simple -- Constantino Vázquez Blanco, PhD, MSc Senior Infrastructure Architect at C12G Labs www.c12g.com | @C12G | es.linkedin.com/in/tinova -- Confidentiality Warning: The information contained in this e-mail and any accompanying documents, unless otherwise expressly indicated, is confidential and privileged, and is intended solely for the person and/or entity to whom it is addressed (i.e. those identified in the To and cc box). They are the property of C12G Labs S.L.. Unauthorized distribution, review, use, disclosure, or copying of this communication, or any part thereof, is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify us immediately by e-mail at ab...@c12g.com and delete the e-mail and attachments and any copy from your system. C12G thanks you for your cooperation. On 31 August 2014 15:21, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Hi I ran the command /usr/share/one/install_gems and it will be installed Grazie Vincenzo Barbieri -Original Message- From: Giovanni Toraldo [mailto:m...@gionn.net] Sent: domenica 31 agosto 2014 14:49 To: Vincenzo Barbieri Cc: Users OpenNebula Subject: Re: [one-users] Softlayer Error Ciao Vincenzo, On Fri, Aug 29, 2014 at 11:57 PM, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Fri Aug 29 23:46:33 2014 [Z0][InM][I]: /usr/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require': no such file to load -- softlayer_api (LoadError) remember to run install_gems after the ruby upgrade since gems needs to be installed for the newer Ruby version. Cheers, -- Giovanni Toraldo http://gionn.net ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
Re: [one-users] Softlayer Error
Hi I have a problem that I think is related to the version of Ruby. I ran the update, and I know how the Ruby version 2.1. But when I look in the logs I see that the service oned makes a call using version 1.8. I also run install_gem but nothing changes Grazie Vincenzo Barbieri via Borgazzi, 27 20900 Monza c.so Orbassano, 336 10137 Torino Mobile: (+39) 342 6521139 vincenzo.barbi...@blueit.it www.blueit.it Please consider the environment before printing this document Questo messaggio di posta elettronica contiene informazioni di carattere riservato, privato e confidenziali rivolte esclusivamente al destinatario sopra indicato. E' vietato l'uso, la diffusione, distribuzione o riproduzione da parte di ogni altra persona. Nel caso aveste ricevuto questo messaggio di posta elettronica per errore, siete pregati di segnalarlo immediatamente al mittente e distruggere quanto ricevuto (compresi i file allegati) senza farne copia. Qualsivoglia utilizzo non autorizzato del contenuto di questo messaggio costituisce violazione dell'obbligo di non prendere cognizione della corrispondenza tra altri soggetti, salvo piu grave illecito, ed espone il responsabile alle relative conseguenze. This e-mail message is for the designated recipient only and may contain legally privileged, proprietary, or otherwise private information. If you are not the intended recipient(S) and/or if you have received this e-mail in error, please notify the sender and destroy the original message and its attachments without reading or saving it in any manner. Any use, distribution, reproduction or disclosure by any other person is strictly prohibited. -Original Message- From: Tino Vazquez [mailto:cvazq...@c12g.com] Sent: martedì 2 settembre 2014 11:45 To: Vincenzo Barbieri Cc: Giovanni Toraldo; Users OpenNebula Subject: Re: [one-users] Softlayer Error Dear Vicenzo, How is the SoftLayer plugin evaluation going? We are very interested in receiving feedback about this feature introduced in OpenNebula 4.8. Thanks in advance, -Tino -- OpenNebula - Flexible Enterprise Cloud Made Simple -- Constantino Vázquez Blanco, PhD, MSc Senior Infrastructure Architect at C12G Labs www.c12g.com | @C12G | es.linkedin.com/in/tinova -- Confidentiality Warning: The information contained in this e-mail and any accompanying documents, unless otherwise expressly indicated, is confidential and privileged, and is intended solely for the person and/or entity to whom it is addressed (i.e. those identified in the To and cc box). They are the property of C12G Labs S.L.. Unauthorized distribution, review, use, disclosure, or copying of this communication, or any part thereof, is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify us immediately by e-mail at ab...@c12g.com and delete the e-mail and attachments and any copy from your system. C12G thanks you for your cooperation. On 31 August 2014 15:21, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Hi I ran the command /usr/share/one/install_gems and it will be installed Grazie Vincenzo Barbieri -Original Message- From: Giovanni Toraldo [mailto:m...@gionn.net] Sent: domenica 31 agosto 2014 14:49 To: Vincenzo Barbieri Cc: Users OpenNebula Subject: Re: [one-users] Softlayer Error Ciao Vincenzo, On Fri, Aug 29, 2014 at 11:57 PM, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Fri Aug 29 23:46:33 2014 [Z0][InM][I]: /usr/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require': no such file to load -- softlayer_api (LoadError) remember to run install_gems after the ruby upgrade since gems needs to be installed for the newer Ruby version. Cheers, -- Giovanni Toraldo http://gionn.net ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
Re: [one-users] Softlayer Error
Hi Vincenzo, Yes, the problem is most likely the ruby version, as the softlayer gem requires a higher version that what is packaged in most distributions. What OS are you using? Did you use rbenv or rvm to bump the ruby version? If so, you may try what is suggested in this ticket [1] Regards, -Tino [1] http://dev.opennebula.org/issues/3139 -- OpenNebula - Flexible Enterprise Cloud Made Simple -- Constantino Vázquez Blanco, PhD, MSc Senior Infrastructure Architect at C12G Labs www.c12g.com | @C12G | es.linkedin.com/in/tinova -- Confidentiality Warning: The information contained in this e-mail and any accompanying documents, unless otherwise expressly indicated, is confidential and privileged, and is intended solely for the person and/or entity to whom it is addressed (i.e. those identified in the To and cc box). They are the property of C12G Labs S.L.. Unauthorized distribution, review, use, disclosure, or copying of this communication, or any part thereof, is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify us immediately by e-mail at ab...@c12g.com and delete the e-mail and attachments and any copy from your system. C12G thanks you for your cooperation. On 2 September 2014 11:49, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Hi I have a problem that I think is related to the version of Ruby. I ran the update, and I know how the Ruby version 2.1. But when I look in the logs I see that the service oned makes a call using version 1.8. I also run install_gem but nothing changes Grazie Vincenzo Barbieri via Borgazzi, 27 20900 Monza c.so Orbassano, 336 10137 Torino Mobile: (+39) 342 6521139 vincenzo.barbi...@blueit.it www.blueit.it Please consider the environment before printing this document Questo messaggio di posta elettronica contiene informazioni di carattere riservato, privato e confidenziali rivolte esclusivamente al destinatario sopra indicato. E' vietato l'uso, la diffusione, distribuzione o riproduzione da parte di ogni altra persona. Nel caso aveste ricevuto questo messaggio di posta elettronica per errore, siete pregati di segnalarlo immediatamente al mittente e distruggere quanto ricevuto (compresi i file allegati) senza farne copia. Qualsivoglia utilizzo non autorizzato del contenuto di questo messaggio costituisce violazione dell'obbligo di non prendere cognizione della corrispondenza tra altri soggetti, salvo piu grave illecito, ed espone il responsabile alle relative conseguenze. This e-mail message is for the designated recipient only and may contain legally privileged, proprietary, or otherwise private information. If you are not the intended recipient(S) and/or if you have received this e-mail in error, please notify the sender and destroy the original message and its attachments without reading or saving it in any manner. Any use, distribution, reproduction or disclosure by any other person is strictly prohibited. -Original Message- From: Tino Vazquez [mailto:cvazq...@c12g.com] Sent: martedì 2 settembre 2014 11:45 To: Vincenzo Barbieri Cc: Giovanni Toraldo; Users OpenNebula Subject: Re: [one-users] Softlayer Error Dear Vicenzo, How is the SoftLayer plugin evaluation going? We are very interested in receiving feedback about this feature introduced in OpenNebula 4.8. Thanks in advance, -Tino -- OpenNebula - Flexible Enterprise Cloud Made Simple -- Constantino Vázquez Blanco, PhD, MSc Senior Infrastructure Architect at C12G Labs www.c12g.com | @C12G | es.linkedin.com/in/tinova -- Confidentiality Warning: The information contained in this e-mail and any accompanying documents, unless otherwise expressly indicated, is confidential and privileged, and is intended solely for the person and/or entity to whom it is addressed (i.e. those identified in the To and cc box). They are the property of C12G Labs S.L.. Unauthorized distribution, review, use, disclosure, or copying of this communication, or any part thereof, is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify us immediately by e-mail at ab...@c12g.com and delete the e-mail and attachments and any copy from your system. C12G thanks you for your cooperation. On 31 August 2014 15:21, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Hi I ran the command /usr/share/one/install_gems and it will be installed Grazie Vincenzo Barbieri -Original Message- From: Giovanni Toraldo [mailto:m...@gionn.net] Sent: domenica 31 agosto 2014 14:49 To: Vincenzo Barbieri Cc: Users OpenNebula Subject: Re: [one-users] Softlayer Error Ciao Vincenzo, On Fri, Aug 29, 2014 at 11:57 PM, Vincenzo Barbieri vincenzo.barbi...@blueit.it wrote: Fri Aug 29 23:46:33 2014 [Z0][InM][I]: /usr/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require': no such file to load -- softlayer_api (LoadError) remember to
Re: [one-users] Can't loginto sunstone after upgrade to 4.8
Hi, On 29 August 2014 12:29, Daniel Dehennin daniel.dehen...@baby-gnu.org wrote: # Make serveradmin using core auth to change the password oneadmin@nebula:~$ oneuser chauth serveradmin core -r serveradmin.pwd # Switch back to server_cipher oneadmin@nebula:~$ oneuser chauth serveradmin server_cipher You can just use this command to change the password oneadmin@nebula:~$ oneuser passwd serveradmin -r serveradmin.pwd --sha1 Cheers -- -- Daniel Molina Project Engineer OpenNebula - Flexible Enterprise Cloud Made Simple www.OpenNebula.org | dmol...@opennebula.org | @OpenNebula ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
Re: [one-users] Type Filesystem
Hi Maria, It depends on your use case, but vmdk_thin is probably a good choice since it will create a DATABLOCK that will take only the space that is actually consuming, and it will grow up to the DATABLOCK size as soon as data is stored in it (ie, sparse file) You can find other options here: http://docs.opennebula.org/4.8/administration/virtualization/evmwareg.html#datablocks-volatile-disks Best regards, -Tino -- OpenNebula - Flexible Enterprise Cloud Made Simple -- Constantino Vázquez Blanco, PhD, MSc Senior Infrastructure Architect at C12G Labs www.c12g.com | @C12G | es.linkedin.com/in/tinova -- Confidentiality Warning: The information contained in this e-mail and any accompanying documents, unless otherwise expressly indicated, is confidential and privileged, and is intended solely for the person and/or entity to whom it is addressed (i.e. those identified in the To and cc box). They are the property of C12G Labs S.L.. Unauthorized distribution, review, use, disclosure, or copying of this communication, or any part thereof, is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify us immediately by e-mail at ab...@c12g.com and delete the e-mail and attachments and any copy from your system. C12G thanks you for your cooperation. On 22 August 2014 08:30, Maria Jular maria.ju...@fcsc.es wrote: Hello, I attach a pic with the field where you have to fill the filesystem type. I’m using “vmdk_thin”. Thank you! *María Jular Castañeda* *Técnico de Sistemas* Tfn: +34-987-29 33 23 / e-mail: maria.ju...@fcsc.es x...@fcsc.es http://www.fcsc.es Edificio CRAI-TIC. Campus de Vegazana, s/n. Universidad de León 24071 León [image: cid:image004.jpg@01CEDEE4.54E4BEB0] [image: logoFCSCL_bn.png] Este mensaje se dirige exclusivamente a su destinatario y puede contener información privilegiada o confidencial. Si Vd. no es el destinatario indicado, queda notificado de que la lectura, utilización, divulgación y/o copia sin autorización está prohibida en virtud de la legislación vigente. Si ha recibido este mensaje por error, le rogamos que nos lo comunique inmediatamente por esta misma vía y proceda a su destrucción. El correo electrónico vía Internet no permite asegurar la confidencialidad de los mensajes que se transmiten ni su integridad o correcta recepción. La Fundación Centro de Supercomputación de Castilla y León no asume ninguna responsabilidad por estas circunstancias. This message is intended exclusively for its addressee and may contain information that is CONFIDENTIAL and protected by a professional privilege or whose disclosure is prohibited by law. If you are not the intended recipient you are hereby notified that any read, dissemination, copy or disclosure of this communication is strictly prohibited by law. If this message has been received in error, please immediately notify us via e-mail and delete it. Internet e-mail neither guarantees the confidentiality nor the integrity or proper receipt of the messages sent. Fundación Centro de Supercomputación de Castilla y León does not assume any liability for those circumstances. *De:* Javier Fontan [mailto:jfon...@opennebula.org] *Enviado el:* jueves, 21 de agosto de 2014 15:48 *Para:* Maria Jular *CC:* users *Asunto:* Re: [one-users] Type Filesystem I don't fully inderstand the question. Anyway for VMware you either use a SAN connected to the hypervisor nodes using vmfs or you export an NFS share to them. For NFS we have been using ext4 from a linux machine without troubles. 2014-08-20 10:01 GMT+02:00 Maria Jular maria.ju...@fcsc.es: Hello, What filesystem type is the best to create a datablock image in Sunstone using vmware with opennebula 4.6.2? Thank you! *María Jular Castañeda* *Técnico de Sistemas* Tfn: +34-987-29 33 23 / e-mail: maria.ju...@fcsc.es x...@fcsc.es http://www.fcsc.es Edificio CRAI-TIC. Campus de Vegazana, s/n. Universidad de León 24071 León [image: cid:image004.jpg@01CEDEE4.54E4BEB0] [image: logoFCSCL_bn.png] Este mensaje se dirige exclusivamente a su destinatario y puede contener información privilegiada o confidencial. Si Vd. no es el destinatario indicado, queda notificado de que la lectura, utilización, divulgación y/o copia sin autorización está prohibida en virtud de la legislación vigente. Si ha recibido este mensaje por error, le rogamos que nos lo comunique inmediatamente por esta misma vía y proceda a su destrucción. El correo electrónico vía Internet no permite asegurar la confidencialidad de los mensajes que se transmiten ni su integridad o correcta recepción. La Fundación Centro de Supercomputación de Castilla y León no asume ninguna responsabilidad por estas circunstancias. This message is intended exclusively for its addressee and may contain information that is CONFIDENTIAL and protected by a professional privilege or whose
Re: [one-users] ubuntu 14.04 as image - no network on first boot
There is a pull request that should fix this problem. I'll generate new packages as soon as possible. Thanks for the tip. https://github.com/OpenNebula/addon-context-linux/pull/4 On Wed, Aug 6, 2014 at 5:40 PM, Wilma Hermann wilma.herm...@gmail.com wrote: Hi, Just stumbled on a curious case today: Using the new context packages under Ubuntu 14.04 killed my loopback NIC since it was left it without an IP (so 127.0.0.1 was not set). I changed the script to call '/sbin/ifquery -X lo -la' to leave the loopback device as is. Furthermore, under Ubuntu 12.04 ifquery has different console options. No idea if they changed it recently, but for the same functionality under 12.04 one must call '/sbin/ifquery -e lo --list'. Using the 14.04 call from above throws an error. Greetings Wilma 2014-04-28 22:20 GMT+02:00 Javier Fontan jfon...@opennebula.org: I've updated the debian packages with the ip flush command sent by Stefan (thanks!). Now it seems to work even when an IP was previously configured in the interfaces file. This will make the context scripts more resilient when you save a disk without cleaning the interfaces file. http://dev.opennebula.org/attachments/download/780/one-context_4.6.0.deb If there are no major bugs with the new package this will be the one linked in the documentation. ML, the source of the context packages in the OpenNebula repository [1]. We usually put the created packages in the files section of the development web pages [2] and link them in the documentation [3]. [1] https://github.com/OpenNebula/one/tree/master/share/scripts/context-packages [2] http://dev.opennebula.org/projects/opennebula/files [3] http://docs.opennebula.org/4.6/user/virtual_machine_setup/bcont.html On Mon, Apr 28, 2014 at 5:55 PM, ML mail mlnos...@yahoo.com wrote: Thanks for the new package. I just tested this version 4.6.0 which now works perfectly with ubuntu 14.04 and I have network access from the first boot. Btw: is there an official repository or download page for the ONE context packages? On Saturday, April 26, 2014 2:28 AM, Javier Fontan jfon...@opennebula.org wrote: We have applied the changes made by Michael. That seems to do the trick. Thank you! You can find the package at http://dev.opennebula.org/attachments/download/779/one-context_4.6.0.deb Cheers On Fri, Apr 25, 2014 at 8:54 AM, ML mail mlnos...@yahoo.com wrote: Small addition here: after the first boot (where the network is not available) instead of rebooting (where the network works afterwards), I can simply run ifup eth0 and the network is working. So somehow ONE context sets things up correctly but eth0 is simply not up after the first boot... On , ML mail mlnos...@yahoo.com wrote: I also had no problems with Ubuntu 12.04, this problem only arises with 14.04. After installing the package I did not touch the interfaces file, actually I never touched it and strangely enough it has the correct context data in it but eth0 is just not configured upon first boot. Maybe it's my Ubutnu 14.04 image itself... I installed a minimal server version of Ubuntu with only OpenSSH from the tasksel menu. Do I maybe need additional packages or to run/configure anything additional post-installation? Regards ML On Thursday, April 24, 2014 7:57 PM, Javier Fontan jfon...@opennebula.org wrote: We have tested the package in both 12.04 and 14.04. Network works fine in the first boot. Did you modify interfaces file after installing the package? One of the things the package does is to empty the interfaces file, just has the loopback configured so it does not configure the network before the context package starts. On Thu, Apr 24, 2014 at 2:55 PM, Javier Fontan jfon...@opennebula.org wrote: Thanks! I'll take a look at it and test it in other distros. On Thu, Apr 24, 2014 at 8:00 AM, Michael Kutzner michael.kutz...@virtion.de wrote: Hi Javier, Am 23.04.2014 um 21:18 schrieb Javier Fontan jfon...@opennebula.org: Network restart is not supported in ubuntu. There is new code to overcome this issue but we are still testing the packages. A package with the latest code is attached if you want to try. You can install it over the previous version. I run into the same problem today and tried to figure out what could be a way also to included fixed interfaces configured in /etc/network/interfaces.d. So, I slightly changed at the end of 00-network (from configure_network on) == snip == configure_network() { gen_network_configuration /etc/network/interfaces echo source /etc/network/interfaces.d/*.cfg /etc/network/interfaces } deactivate_network() { . /etc/os-release if [ $ID = ubuntu ]; then IFACES=`/sbin/ifquery -la` for i in $IFACES; do DEV=`get_dev $i` /sbin/ifdown $i done else
Re: [one-users] CentOS 7 - KVM - OpenNebula 4.8 from Marketplace doesn't start
Hi, I've just uploaded a new version of the image with the correct format. On Tue, Aug 26, 2014 at 11:52 AM, Pavel Tankov pavel.tan...@strategyobject.com wrote: We are going to convert it to a more compatible version and reupload. Hello, guys. Any progress on that? Thanks. On 08/21/2014 04:23 PM, Javier Fontan wrote: We found a problem with the format of that image. It only works with qemu = 1.10. We are going to convert it to a more compatible version and reupload. In case you have a machine with a newer qemu version you can use this command to convert it: $ qemu-img convert -f qcow2 -O qcow2 -o compat=0.10 orig_image dest_image Sorry for the inconveniences. On Thu, Aug 21, 2014 at 10:16 AM, Pavel Tankov pavel.tan...@strategyobject.com wrote: Hello Users, I have the following setup: Physical host: CentOS 6.5 (64 bit, of course), KVM, all set up following the Quickstart Guide here: http://docs.opennebula.org/4.8/design_and_installation/quick_starts/qs_centos_kvm.html Opennebula 4.8.0 I got from the Marketplace the image named CentOS 7 - KVM - OpenNebula 4.8. Imported it and it and created the template automatically for me. I modified the template to add my ssl public key to be able to login as root, added a network and pretty much that was it. I tried to instantiate the template, but the VM keeps getting into the FAILED status. Do you have any idea why it wouldn't start? Thanks in advance. Here is the VM log: BEGIN LOG Wed Jul 30 18:00:53 2014 [DiM][I]: New VM state is ACTIVE. Wed Jul 30 18:00:53 2014 [LCM][I]: New VM state is PROLOG. Wed Jul 30 18:00:56 2014 [LCM][I]: New VM state is BOOT Wed Jul 30 18:00:56 2014 [VMM][I]: Generating deployment file: /var/lib/one/vms/9/deployment.0 Wed Jul 30 18:00:56 2014 [VMM][I]: ExitCode: 0 Wed Jul 30 18:00:56 2014 [VMM][I]: Successfully execute network driver operation: pre. Wed Jul 30 18:00:57 2014 [VMM][I]: ExitCode: 0 Wed Jul 30 18:00:57 2014 [VMM][I]: Successfully execute virtualization driver operation: deploy. Wed Jul 30 18:00:57 2014 [VMM][I]: ExitCode: 0 Wed Jul 30 18:00:57 2014 [VMM][I]: Successfully execute network driver operation: post. Wed Jul 30 18:00:57 2014 [LCM][I]: New VM state is RUNNING Thu Jul 31 14:03:18 2014 [LCM][I]: New VM state is SHUTDOWN Thu Jul 31 14:03:51 2014 [VMM][I]: ExitCode: 0 Thu Jul 31 14:03:51 2014 [VMM][I]: Successfully execute virtualization driver operation: shutdown. Thu Jul 31 14:03:51 2014 [VMM][I]: ExitCode: 0 Thu Jul 31 14:03:51 2014 [VMM][I]: Successfully execute network driver operation: clean. Thu Jul 31 14:03:51 2014 [LCM][I]: New VM state is EPILOG Thu Jul 31 14:03:51 2014 [DiM][I]: New VM state is DONE Thu Aug 7 12:09:20 2014 [DiM][I]: New VM state is ACTIVE. Thu Aug 7 12:09:20 2014 [LCM][I]: New VM state is PROLOG. Thu Aug 7 12:09:21 2014 [LCM][I]: New VM state is BOOT Thu Aug 7 12:09:21 2014 [VMM][I]: Generating deployment file: /var/lib/one/vms/9/deployment.0 Thu Aug 7 12:09:21 2014 [VMM][I]: ExitCode: 0 Thu Aug 7 12:09:21 2014 [VMM][I]: Successfully execute network driver operation: pre. Thu Aug 7 12:09:22 2014 [VMM][I]: ExitCode: 0 Thu Aug 7 12:09:22 2014 [VMM][I]: Successfully execute virtualization driver operation: deploy. Thu Aug 7 12:09:22 2014 [VMM][I]: ExitCode: 0 Thu Aug 7 12:09:22 2014 [VMM][I]: Successfully execute network driver operation: post. Thu Aug 7 12:09:22 2014 [LCM][I]: New VM state is RUNNING Thu Aug 7 12:24:05 2014 [LCM][I]: New VM state is SHUTDOWN Thu Aug 7 12:24:15 2014 [VMM][I]: ExitCode: 0 Thu Aug 7 12:24:15 2014 [VMM][I]: Successfully execute virtualization driver operation: shutdown. Thu Aug 7 12:24:15 2014 [VMM][I]: ExitCode: 0 Thu Aug 7 12:24:15 2014 [VMM][I]: Successfully execute network driver operation: clean. Thu Aug 7 12:24:15 2014 [LCM][I]: New VM state is EPILOG Thu Aug 7 12:24:16 2014 [DiM][I]: New VM state is DONE Tue Aug 19 16:03:52 2014 [DiM][I]: New VM state is ACTIVE. Tue Aug 19 16:03:52 2014 [LCM][I]: New VM state is PROLOG. Tue Aug 19 16:03:53 2014 [LCM][I]: New VM state is BOOT Tue Aug 19 16:03:53 2014 [VMM][I]: Generating deployment file: /var/lib/one/vms/9/deployment.0 Tue Aug 19 16:03:53 2014 [VMM][I]: ExitCode: 0 Tue Aug 19 16:03:53 2014 [VMM][I]: Successfully execute network driver operation: pre. Tue Aug 19 16:03:53 2014 [VMM][I]: ExitCode: 0 Tue Aug 19 16:03:53 2014 [VMM][I]: Successfully execute virtualization driver operation: deploy. Tue Aug 19 16:03:53 2014 [VMM][I]: ExitCode: 0 Tue Aug 19 16:03:53 2014 [VMM][I]: Successfully execute network driver operation: post. Tue Aug 19 16:03:53 2014 [LCM][I]: New VM state is RUNNING Tue Aug 19 16:05:37 2014 [LCM][I]: New VM state is CLEANUP. Tue Aug 19 16:05:37 2014 [DiM][I]: New VM state is DONE Tue Aug 19 16:05:37 2014 [VMM][W]: Ignored: LOG I 9 Driver command for 9 cancelled Tue Aug 19 16:05:38 2014 [VMM][W]: Ignored: LOG I 9 error:
Re: [one-users] Can't loginto sunstone after upgrade to 4.8
Daniel Molina dmol...@opennebula.org writes: [...] You can just use this command to change the password oneadmin@nebula:~$ oneuser passwd serveradmin -r serveradmin.pwd --sha1 Ok, I did not understand why it was not working without the --sha1. Thanks. -- Daniel Dehennin Récupérer ma clef GPG: gpg --recv-keys 0xCC1E9E5B7A6FE2DF Fingerprint: 3E69 014E 5C23 50E8 9ED6 2AAD CC1E 9E5B 7A6F E2DF signature.asc Description: PGP signature ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
[one-users] Thin provisioning and image size
Hello, The size of my qcow2 images is always reported as 1M: IMAGE 114 INFORMATION ID : 114 NAME : debian-wheezy USER : nebula GROUP : nebula DATASTORE : default TYPE : OS REGISTER TIME : 04/10 10:18:26 PERSISTENT : No SOURCE : /var/lib/one/datastores/1/5d2be6f9746fc3447be11c6621da87df FSTYPE : save_as SIZE : 1M STATE : rdy RUNNING_VMS: 0 PERMISSIONS OWNER : um- GROUP : u-- OTHER : u-- IMAGE TEMPLATE DEV_PREFIX=vd DRIVER=qcow2 SAVED_DISK_ID=0 SAVED_IMAGE_ID=17 SAVED_VM_ID=347 SAVE_AS=YES As far as I understand, the size is calculated only at creation time and never updated. I think we could differentiate the real size from the virtual size in case of thin provisioning like qcow2, qemu-img actually reports: qemu-img info /var/lib/one/datastores/1/5d2be6f9746fc3447be11c6621da87df image: /var/lib/one/datastores/1/5d2be6f9746fc3447be11c6621da87df file format: qcow2 virtual size: 40G (42949672960 bytes) disk size: 629M cluster_size: 65536 Format specific information: compat: 1.1 lazy refcounts: false Regards. -- Daniel Dehennin Récupérer ma clef GPG: gpg --recv-keys 0xCC1E9E5B7A6FE2DF Fingerprint: 3E69 014E 5C23 50E8 9ED6 2AAD CC1E 9E5B 7A6F E2DF signature.asc Description: PGP signature ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
Re: [one-users] OpenNebula 4.8 ESX Sandbox (from marketplace) has no eth0 attached
Hi Rustam, You are right, the udev persistent rule was preventing for a correct network configuration. We've updated the appliance to remove the rule: http://marketplace.c12g.com/appliance/53e4e9258fb81d6a8207 Let us know if you find anything else, we appreciate the feedback. Best regards, -Tino -- OpenNebula - Flexible Enterprise Cloud Made Simple -- Constantino Vázquez Blanco, PhD, MSc Senior Infrastructure Architect at C12G Labs www.c12g.com | @C12G | es.linkedin.com/in/tinova -- Confidentiality Warning: The information contained in this e-mail and any accompanying documents, unless otherwise expressly indicated, is confidential and privileged, and is intended solely for the person and/or entity to whom it is addressed (i.e. those identified in the To and cc box). They are the property of C12G Labs S.L.. Unauthorized distribution, review, use, disclosure, or copying of this communication, or any part thereof, is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify us immediately by e-mail at ab...@c12g.com and delete the e-mail and attachments and any copy from your system. C12G thanks you for your cooperation. On 2 September 2014 02:36, Rustam Ismail rustam.ism...@gmail.com wrote: Hi, I want to inform you that the appliance linked here OpenNebula 4.8 ESX Sandbox has no eth0 available. I was using VMware ESXi. The result was the same when running it via Virtualbox. Only br0 availble. It gave me a lot headache to find out why since eth0 is standard nowadays, a must have one. I thought that when building the appliance, then he/she must have at least one ethernet card attached physically, right? I saw that /etc/sysconfig/network-script/ifcfg-eth0 was there, using dhcp as bootproto. Running ifcofig eth0 up showed up a failure message. I found the answer why while reading an ebook, I noticed that there is a mention that you need to remove the /etc/udev/rules.d/70-persistent-net.rules in order to prevent the network interface coming up as an interface other than eth0. So, I did just as told, restart the network service, and voila! It works, the eth0 is now there and enabling me to login to Sunstone. The funny thing is, that ebook I read and found the answer is an ebook about OpenStack :) Perhaps you guys should add a note about this and howto overcome the missing eth0 in the appliances. Regards, Salam, Rustam ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org ___ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org